Router time setting

right now, my time setting (under status, router) reads "not available". It used to show the date and time, but I had to power reset the router. How do I get the router to recapture the date and time? I need this to engage the access restrictions policy.

On most Linksys routers, you can only set the time zone. Then connect the router to the Internet, and it will pick up the correct time automatically.
If you need more help, please state your router model and version.
Message Edited by toomanydonuts on 04-28-200710:34 PM

Similar Messages

Router Filter Setting

I need help on router filter setting. I am using router model WRT160Nv3. I have a very specific set of filtering requirements (see below) to be implemented. I implemented all of them except the first one. It is not clear to me how I could implement that. I am including all the requirements because I think I run out of filtering policy (the router allows only 10 policies)
Filtering requirements:
1. Allow all machines access to internet from 3:00 to 4:00pm, and from 7:00 to 12:00 midnight (each policy can have only one time range)
2. Block 6 different sites 24 x 7 (each policy can block up to 4 sites)
3. Block 30 different keywords (each policy can block up to 4 keywords)
Couple questions:
1. What is the "combining" logic on multiple policies? Are they AND together or OR together? Do ALLOW and DENY use the same or different logic?
2. Each policy allows only one time range. Does it mean that I have to split requirement 1 into 2 policies, one for each range? If I use two policies,
    it seems the "combining" logic may be difficult?
Thank you for your help in advance,
AK

Mario,
I resolved my problem.
Make sure your router is also WRT160Nv3. My solution applies only to that model.
There were couple things that I did:
1. Reduced the number of keywords to be filtered so that they used up less policies.
2. All policies have the same logics:
    If the conditions meet, it will apply the actions. The conditions are: time range, site names, keywords, etc.
    The actions are allow or deny corresponding to the condition.
    For example, if one of the policy said site www.xyz.com would be blocked. If the site occurred, that policy would
    fire and block the site. That means the logic is OR among the policies.
3. You can use up all the conditions in the same policy. All the conditions are independent of each other.
    For example, each keyword is blocked independent of other keywords, regardless of the time range.
4. I set up one policy with time range = 24 hours for allow.
    Then set up another policy with time range = 4:00pm to 7:00pm for deny. That covered my time range requirements.
5. Then I set up other policies to cover sites and keywords. Since they were all independent to each other,
    as long as the condition occurred to any one of the policies, the policy would fire and perform the action.
I hope that would answer your question.
Andrew K

EA6900 Router Time incorrect

Hi,
I get the following in linksys smartwifi, showing that the router time is way off:
Current Router Time:
Monday, 23 March 2015 13:38:22 (GMT +01:00)
Current Browser Time:
Sunday, 05 April 2015 11:28:43 (GMT +02:00)
(don't mind the GMT+1 and +2 difference, that is because DST was not active on 23/03).
The difference was something around 5 hours until I rebooted the router. Now it is 13 days...
The problem is that there is NO option to set the time, or even an option to manually trigger a sync. I have tried to reinstall the firmware, which is the solution from the thread http://community.linksys.com/t5/Wireless-Routers/WRT-1900ac-Router-Time-Inaccurate/m-p/930840 , to no avail.
What I actually want to do is use the parental controls, but I cannot do that unless the router time is correct.
Please help!

Also, look in the logs for a cnnection that goes to 'ntp' which is how it gets the time settings.

How to get calendar travel time (set up in Mavericks) to show on iOS 7 calendar?

I was wondering how to get calendar travel time (set up in Mavericks) to show on iOS 7 calendar? If I change a location in mavericaks it is updated in my iOS 7 calendar, but if I add travel time to an appointment, that does not show up on my iphone. This seems like a big miss for apple if this is the case. I could maybe understand not adding the ability to add travel time in iOS 7, but not being able to see the travel times you set up seems very incomplete. Any ideas or insight?

Hello Cheer,
I don't believe the table changed when migrating from Access. I had two tables before the migration, one was for the SwitchBoard Manager and the other table was for the database table. I used the Switchboard to navigate to different menus, such
as the Main Form, Power Form, Server Form, etc. Let me know if I can provide any other information to help you narrow this down for me.
Thank you for your assistance.
Thai

Is there a way to automatically change tabs with different times set for each tab?

I found a few add-ons that will automatically change tabs based on a configurable time. But all the tabs use the same time setting. What I need is the ability to have tabs displayed for different amounts of time. Ex, Tab 1 for 30 seconds, Tab 2 for 10 seconds, Tab 3 and 4 for 5 seconds. Ideally, I will have the ability to modify these settings as the amount of tabs and the content will change a couple times a week.
Currently I'm using Tab Slideshow with each tab displayed for 15 seconds. But it sounds like Tab Rotate and Auto Toggle Tabs essentially do the same. If there is already a solution that would be great but if not is there someone available for hire to help modify one of the existing add-ons? Thank you in advance for your time.
John

Currently Firefox don't have any options like that.
You can ask the Addon developers
*http://addons.mozilla.org/

First time setting up a Time Capsule on Windows 7

Hi all!
I know this is not a new issue but I can't seem to find the right answer to my problem.
I have a Time Capsule here and my actual setup is: Modem -> Router -> PC / Modem -> Router -> Time Capsule, and I would like to access my Time Capsule from my Windows PC.
I've installed the Airport Utility but it can't find the Time Capsule.
What should I do? Do I really need to connect it directly to my computer?

I have a Time Capsule here and my actual setup is: Modem -> Router -> PC / Modem -> Router -> Time Capsule
Just to be sure I understand your current network configuration. You have a single modem. You have a router connected directly to this modem via Ethernet, and in turn, you have both your PC & the Time Capsule connected to the router, each with its own Ethernet cable.
If this is correct, then the only thing necessary to allow the PC to access the Time Capsule's internal drive is to reconfigure the Time Capsule as a bridge.
To do so you would use AirPort Utility for Windows, as follows:
Run the AirPort Utility.
Select the Time Capsule, and then, select Manual Setup.
Select the Internet tab.
Change the Connection Sharing option to: Off (Bridge Mode)
Click on Update and allow the Time Capsule to restart.

Having very difficult time setting up and running time capsule and airport

I am having a very difficult time setting up and running airport express and time capsule. My time machine is not being recognized by my mac. The amber light keeps blinking. I'm ready to stsrt over.

#3 for itunes streaming. I reset the base station and eventually was able to get the backup working and now my green light is on. Next I'd like to be able to play itunes using Airport Express and have connected to my stereo receiver in another room.
AirPort Express Base Station (AX) - iTunes Setup
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <existing TC's wireless network>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
Verify Password: <re-enter the existing wireless network password>
AirPort Utility > Select the AX > Manual Setup >Music
Enable AirTunes (checked)
iTunes Speaker Name: <enter desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings to the AX

To use a router to set up a local wifi network. Would this system be suitable to use with an Apple TV or is internet access require

I'm considering using Apple TV to connect to a projector in a church hall which does not have any internet access. I intend to use a router to set up a local wifi network. Would this system be suitable to use with an Apple TV or is internet access require

Welcome to the Apple Community.
Yes, that will be fine providing you don't want to play any protected content.

Can not acces the router's set up page

I am trying to access the router's set up page and can't. I typed in 192.168.1.1 and typed in the word "admin" in the password (left the username blank), and get nothing. I tried unplugging, and resetting the router and still dont get anything, it just keeps asking me for the right password. Can someone help me please? I need to get my passphrase (which I forgot), so I can access my wireless internet. I never needed this before now, so I don't remember what it is. I was able to get online just fine, but now all of the sudden it is asking for my passphrase. Can someone please help.
Thanks

To view the router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
Some Zone Alarm users have reported that adding 192.168.1.1 to their list of "trusted" addresses fixed the problem. This trick might also work with other firewalls.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If you still have trouble, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

How to change LACPDU timer setting on Microsoft Network Adapter Multiplexor Driver

We’re installing our first Windows 2012 R2 server, and one of the network settings is different from what’s on a comparable Windows 2008 R2 server, and it's not what our network group would like to see connected to their switches. Both servers have
2 NICs teamed using the LACP protocol and are connected to 2 different switches for high availability. In both cases I just teamed the NICs with whatever driver was on the server.
On the 2008 R2 server (the one our network group likes), it’s an Intel driver, “Intel(R) Advanced Network Services Virtual Adapter”. On the 2012 R2 server it’s a Microsoft driver, “Microsoft Network Adapter Multiplexor Driver”. The setting that
our network group is concerned about is the LACPDU timer setting. Apparently it can be either “fast” or “slow”. What they see on the switches is that on the 2008 Intel driver NICs the setting is “slow” and on the 2012 Microsoft driver NICs the
setting is “fast”. The switches are expecting “slow”.
I spent some time searching on Microsoft.com and other places, as well as poking around on the server, but I couldn’t find that setting or how to change it on the Microsoft Network Adapter Multiplexor Driver. Does anyone know how I can change it?
Thanks!

Hi,
According to my knowledge, we can’t change the value of LACP timer.
Here is a related question,
How to change LACP timer-value on Windows server 2012 Network Teaming, from short to long?
http://social.technet.microsoft.com/Forums/en-US/05e2761f-e165-44f6-9bed-d91e9eeba687/how-to-change-lacp-timervalue-on-on-windows-server-2012-network-teaming-from-short-to-long
Hope this helps.
Steven Lee
TechNet Community Support

Is there a DJ app for the Ipad that will read the "start" and "stop time" setting for each individual song, as they are set in the song Options screen in Itunes?

Is there a DJ app for the Ipad that will read the "start" and "stop time" setting for each individual song, as they are set in the song Options screen in Itunes? The Ipod Touch, by itself does not allow cross-fading, therefore when the stop time is edited short, the song jusst truncates then goes to the next song. I tried the DJay ap and while it would crossfade, it would NOT read the song settings for the stop marker. So now I want to try and Ipad and see if there is an app that will READ the Itune stop settings within the song. I do NOT want an app that will allow me to DO the stop marker. I want an app that will READ the stop marker from the song as it is set in Itunes.

Itunes provides the option for setting the Start and Stop times of each music track. However, the start and stop times do not synchronize to the iPhone. I don't understand why this option is even available as it doesn't work when listening to music on the phone. I have not found another application that will support the start and stop time markets. I have searched quite a bit for this but can't find anything. I hope we can find something.

My airport extreme has connected to a Tplink router, i set my AE in Create network, so i get a problem of Double NAT. How can i repair this probleme because i have to use TPlink for my IP TV and i want to use AE to creat my network and the guest NW.

my airport extreme has connected to a Tplink router, i set my AE in Create network, so i get a problem of Double NAT. How can i repair this probleme because i have to use TPlink for my IP TV and i want to use AE to creat my network and the guest NW. If we don't have a solution for this question, can i set my AE to use the IP TV and how??? I'm using a 4th Airport extreme

No, not unless it is simply a network connection.
How is your IPTV being provided.. if it is using a separate vlan or separate vpi/vci in the adsl connection. Who is your ISP?
Is the TP-Link ADSL?
Is the IPTV using a separate voice channel on adsl?
Or a different vlan.
Sorry but it is something where a definite answer is not possible unless you provide all the details.
The setups are unique to each ISP around the world..
Here is one for our local ISP.
http://www.avenard.org/iptv/Setup.html
He has a section on getting this working with apple router over wireless.. look
http://www.avenard.org/iptv/IPTV_and_Wireless.html
Google around and see if other people have had success.. the whole setup is tricky.. and it is hard if nobody has used it who actually understands networking.

Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.

Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.

Mac OS X 10.6 Help: Sharing your Internet connection

The date and time setting go crazy[SOLVED]

Hello,
Each time, I boot up the time setting changes. Sometime two hours behind, sometimes five. Even if I set the time and date by using the "date -s" command or kde time setting feature when reboot the time changes.
Any idea how to fix this for good?
Thanks,
jmak
Last edited by jmak (2009-11-20 00:19:17)

Thanks for all the suggestions.
This what happened. From some strange reasons the system clock setting and the distro setting were different. The bios clock was two hours before the distro clock. I adjusted the bios clock to real time—to correct time thinking this will set the disto time to the correct time too. Rebooted and I was put on the commandline with an error message:"superblock last mount time Thu Nov 19 11:41:29 2009, now=Thu Nov 19 10::53:27 2009 is in the future"
Then I entered the root password and did a "fsck" and rebooted. It booted up fine
but the distro time setting was still wrong. Rebooted again and checked the bios clock and it was reset to the distro clock. Both were wrong but at least have the same settings. Then I boot up again and set the time to the right setting in KDE. Rebooted and checked the bios clock which was adjusted to the distro setting—in other words to the correct settings. Now the time is ok. So it seems that the bios setting depends on the distro setting. I thought it was the other way around.
My computer is relatively new, 2 years old, so I dont think this was a battery problem. Also, I have other distros installed and I haven't experienced these kinds of problems with those distros.
Lately, I experimented with a few distros on different partitions, and what I am suspecting is that those might reset the bios clock which caused the inconsistencies in Kde.
jmak

I have a new WRV210 router, and set it up fine - works as...

I have a new WRV210 router, and set it up fine - works as expected for about 5-10 hours then hangs - pull the power, and restart the device it works again. This is getting old fast.
I use if for a VPN ipsec tunnel - tunnel works great when it is working.
It is also used as a NAT behind an AT&T router getting a DHCP address for the WAN connection.
It has the latest firmware as listed on the web site 1.1.16
I was thinking about reflashing the firmware - any suggestions?
Steve

Hey try resetting the router reset button in such a way that power
light is blinking on the router & then do a complete network power
cycle i.e., unplug the power cables from the modem & from the router &
then plug in the power cable to the modem first once all the lights are
solid green you could plug in the power cable to the router & check out
it will definately work!!

Router time setting

Similar Messages

Maybe you are looking for