Router was not booting from flash

hi
my 2811 router was not able to from flash
while it booting it was showing below message. please find the image.
after this using tftp i was uploaded the ios after uploading it was booting sucessfully. after booting when i reload the router
the above message was showing. then i have to reload the ios. config reg is 0x2102, ios is c2800nm-adventerprisek9-mz.124-24.T.bin
and 15T. bot the ios. on this i have to configure mgcp for fxs ports.
please help me.
thankq.

Remove all the network modules and/or HWIC from the router and reboot again.
Can you please cut-and-paste the entire bootup process (please don't post a photo taken from your mobile phone because you might miss out some important details).

Similar Messages

2851 Router will not boot from CF, after reload goes into rommon

I recently obtained a 2851 and have been battling this issue for a week now. An odd set of circumstances happen with the bootstrap startup process. If the router has loss of power or when reloaded; it fails to read the CF card and boots to rommon. I can tftp an image to it (tftpdnld -r) and IOS CAN read the flash card along with any saved configuration.
In fact once in IOS, I can wr mem and print the hardware details of the CF card. Once I reload the router it goes to rommon, fails to open the flash, then sits until i tftp the image back. When the router load IOS, it also loads the startup config.
I don't think it's a problem with the CF card as IOS can read it. I've tried formatting the card from IOS and from my pc as FAT, FAT16, FAT32, and NTFS - it didn't make a different. I updated the ROMMON to allow for USB booting but haven't purchased a USB Drive yet for testing. The upgrade didn't resolve this issue either. It almost seems like a firmware problem with the EPROM.
I've played with the config register to see what, if any, impact it had. Currently it's set to 0x2102, putting it in the diag register didn't produce any other errors than what's listed below.
I'm stumped and out of ideas. Hoping somebody has some insight on what could be causing this to happen.
Apprecite your time reading my question.
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
loadprog: error - on file open
boot: cannot load "flash:c2800nm-advsecurityk9-
mz.151-3.T2.bin"
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon>

Yes, I have tried different types of CF and USB with the same result. I have "official" cisco 256mb cf and a sandisk cf. I have tried various brands of usbflash.
I added boot system statements to the config to cf, then usb0, then usb1 to see if perhaps one would read. It looks like it doesn't bother after the first device fails. This is only for my studies and I can deal with "tftpdnld -r" every time I boot it. Just was trying to nail down any other possibilies.
System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
Initializing memory for ECC
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
loadprog: error - on file open
boot: cannot load "flash:c2800nm-ipvoice-mz.151-2.T1.bin"
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
open(): Open Error = -66
boot: cannot open "flash:"
boot: cannot determine first executable file name on device "flash:"
c2851 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.
rommon 1 >

I get the message "Install Adobe Flash" can't be opened because it was not downloaded from the Mac App Store. This is the first time I have gotten the message. What do I need to do?

I get the message "Install Adobe Flash" can't be opened because it was not downloaded from the Mac App Store. This is the first time I have gotten the message. What do I need to do?

Hi Sandra,
you'll need to edit the security settings to install programs 'Mac App Store and identified developers'
Open the Systems Preference and go to Security & Privacy. There will be a section in the 'General' tab for 'Allow apps downloaded from:" The default selection is 'Mac App Store'. Change this setting to 'Mac App Store and identified developers".
This screenshot is taken on OS X 10.10 (Yosemite), so it may look slightly different if you're on a different OS X version.
Maria

My compaq cq62-214nr will not boot from a usb flash drive

I have a Compaq CQ62-214 NR Notebook. When I enter the bios boot options screen with F9 there is a blank space where Boot from USB/Flash Drive should be. If I enter the bios setup and move usb flash drive up to the first option above Notebook hardrive and Internal CD/DVD Rom ,save the changes to the BIOS then Reboot. Enter the boot options screen again the blank line moves up to the first choice slot but still is blank. If I press enter over that black option the computer does not boot from the OS I have install on the usb flash drive it just starts its normal windows boot screen. YES I have upgraded the BIOS to the lates version F.37
Can somone tell me what is wrong.

Try booting into the one time boot menu.
Step 1: As soon as you turn on the computer on the hp invent screen keep tapping F9 key.
Step 2: you will get boot otions such as hard drive, optical drive, USb drive
Step 3: You can hit enter on the usb flash drive. Should boot from the os on your flash drive
*Although I am an HP employee, I am speaking for myself and not for HP.
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

Aironet 1600 - A response was not received from the router or access point

Hi,
I'm trying to set up a wireless network with multiple SSID's. The new network only has CISCO products (router, switches). For the moment I'm trying to connect to 1 SSID (Windekind.Gast). the SSID is visible but when connecting devices have te folowing error message in the log:
Connection status summary
Connection started at: 2015-02-17 09:55:49-951
Profile match: Success
Pre-Association: Success
Association: Fail
Security and Authentication: Not started
Root cause:
Wireless association to "Windekind.Gast" failed
A response was not received from the router or access point.
Detailed root cause:
Wireless association to this network failed. Windows did not receive any response from the wireless router or accesspoint.
The signal is perfect (I'm only a few feet away from the AP).
To make sure there is no dhcp problem I tested the swich port in access mode for vlan 30 which supplied an IP correctly. I'm really not seeing the problem and searched the web for days now! Any help would be very much appreciated!
Below the config of the access point (done via de web interface).
! Last configuration change at 05:30:28 UTC Mon Mar 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2452
no preamble-short
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end

Hi Rasika
thanks for the reply! 10.0.0.81 belongs to vlan 1. I changed the config as suggested but no luck.. (same problems are logged in the event viewer). the ap is connected to a switchport in trunk mode and vlan 1 is the native lan (untagged). the port also is joined to vlan 30 (and others).
Below the new config. Hope you can see an error..
! Last configuration change at 22:56:10 UTC Thu Apr 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Default vlan 1
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
   vlan 50
   band-select
   authentication open
   mobility network-id 50
dot11 ssid Windekind.Gast
   vlan 30
   band-select
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   mobility network-id 30
   wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
   vlan 40
   band-select
   mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
no preamble-short
channel 2452
station-role root
payload-encapsulation dot1h
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
t

BIOS update, then will not boot from any drive

This old laptop, 3000 C200 8922 was acting very clunky when on wireless.
Downloaded Bios Version 63ET62WW and flashed it into the bios.
Now, even though I can get to the bios screen, and it shows the hard drive, DVD/CD drive, it will NOT boot from either.
It will also "see" a usb installed, but will not boot from it.
I have removed all power and cleared the CMOS several times and I still have nothing. Tried two different hdd's which have been in the machine and same results.
HELP!! I should have never messed with it......

hi k4pew,
One rule after a BIOS update is to Load optimize deafults after updating.
Try that go inside BIOS Hit F9 to load defaults then F10 to Save and Exit.
If not
Try turning on the computer and start hitting F1 to load the Recovery Menu and see if that will push then Try Reseting the PC.
If still the same Im afraid that the BIOS needs to be reflashed.
Im not aware of any flash tool or a your Previous BIOS Version Firmware available for download.
You can try calling Lenovo Technical Support for any options available for repair.
Im sorry to hear what happened
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Power Mac G4 400 MHz (AGP graphics) will not boot from hard drive

I have a Mac G4 400 MHz (AGP graphics) Machine Model: PowerMac 3.1 CPU Type:PowerPC G4 (2.8)
When I try to boot from the hard drive I get the folder with the flashing question Mark. The Machine will start up from the OSX 10.4 installer disk.
The system was running OSX 10.4.9 fine. I began to have problems with the hard drive, so I replaced it with an old Maxtor 5T040H4 40Gig Apple branded drive that I had sitting around.
The drive is jumpered (r50) for Master/Single.
I erased the drive in the old G4 using disk utility and wrote all zeros. I then used my store bought Tiger 10.4 install disk to install 10.4 on the drive.
After restarting I still get the flashing question mark. If I leave the Install disk in the DVD drive the system will attempt to install again.
I have zapped the PRAM, pressed the CUDA button, removed the battery and let the system sit unplugged for over and hour and it still will not boot from the hard drive.
To test the drive I removed it and put it in a Granite Digital firewire enclosure and connected it to another mac. The drive shows up and the system appears to be installed correctly.
What am I forgetting to do? Does anyone have any suggestions.
Thanks in advance.
Wesley G.

Hi! If Tom's solution doesn't work I would reboot from the install disc and then partition the drive as 1 partition instead of erasing it. Sounds like the driver on the disk is too old and installing a new partition map should write a new driver to the drive that is compatible with Tiger. Other than that it is possible that the drive has a spin delay jumper enabled and the drive isn't spinning up fast enough and the computer isn't looking long enough for the drive. Tom

IBook G3 will not boot from CD/DVD

Ok, I have an iBook G3.
I was restoring it to factory with the Software Restore disks which came with the unit as I was planning to move on to a new unit.. But there was a power cut in the middle of the process and the unit shut off. Now, it does not recognise a HD when booting holding option.
It also will not boot from any CD/DVD other than the Apple HW Test disk provided with the unit.. All other disks spin up and then get ejected, on the odd occasion it does not eject, it boots to a icon of a floppy diskette with a flashing ? (Saying that, I did manage to get it to load from the restore disk 1 once, but it just said it could not mount the image file)
The HW test disk returns no problems
I have reset PRAM multiple times, and reset nvram and all in Open Firmware. I have also reset PMU as a last resort, but no luck
Any ideas?

Hi, and welcome to Apple Discussions.
Do you have DiskWarrior, maybe?

6500 booting from flash

I need to boot my 6500 from external flash, and I put the command "boot system flash s72033-adventerprisek9_wan-mz.122-33.SXI13.bin" to set the boot variable. But still the switch is booting from flash sup-bootdisk: and also the boot variable is set to flash sup-bootdisk: . Can any one please tell me how to solve this issue
this is the show run
boot-start-marker
boot system flash sup-bootdisk:s72033-ipservicesk9_wan-mz.122-33.SXH4.bin
boot system flash s72033-adventerprisek9_wan-mz.122-33.SXI13.bin
boot-end-marker
and
Router#sho bootvar
BOOT variable = sup-bootdisk:s72033-ipservicesk9_wan-mz.122-33.SXH4.bin,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102

Hello
i would suggest to change the boot variable to contain both old and new iOS but have the new iOS try to boot first
Conf t
no boot system
r
boot system flash:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin
boot system flash sup-bootdisk:s72033-ipservicesk9_wan-mz.122-33.SXH4.bin
Sh boot
wr
res
paul

Not booting from 10.4.8 volumes after upgrade from 10.4.7

I'm sorry to report that my aged G4 450 MHz AGP with 4 internal Hard disk drives no longer boots from any of the 2 volumes upgraded to Mac OS X 10.4.8 as soon as it was started from another volume!
All was working fine as long as 10.4.7 was installed on the 2 232 GB disks connected to the SIIG ATA133 controller. I could boot from any OS on any of the 4 disks, 5 partitions:
internal ATA66 bus:
18 GB disk, 2 partitions: 'IBM_18GB' with OS 9.2.2 and TechTool Pro's 'eDrive' with 10.4.7
71 GB disk, 1 partition 'IBM_71GB' with OS 9.2.2
PCI SIIG ATA133 controller:
232 GB disk, one partition 'I1232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
232 GB disk, one partition 'I2232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
Now I can only boot from the Mac OS 9.2.2 or the eDrive 10.4.7 partitions.
What I did so far: 'I2232GB' was my main OS X startup volume, 'I1232GB' contains a clone of it, plus additional folders like software base and backups.
After upgrading 'I2232GB' to Mac OS X 10.4.8 through Software Update and repairing permissions all was OK as long as the Mac was just shut down or re-started: it always booted up in Mac OS X 10.4.8 from 'I2232GB' without any problems.
The next day I booted from 'I1232GB' to do the same there.
Afterwards I could no longer boot in Mac OS X 10.4.8 from 'I2232GB' nor in in Mac OS X 10.4.8 from 'I1232GB': it just gets to the grey screen with the Apple logo, but the round circle underneath indicating some progress never appears. I left it there for hours: it just hangs.
With the Option key held at startup I could boot from the other partitions with Mac OS 9.2.2 or the eDrive with 10.4.7. None of their Startup Control Panels was able to get me back to 10.2.8!
So I booted from the TechTool Pro 4.5.1 DVD to Optimize both volumes, 'I1232GB' & 'I2232GB', always Files only.
Then I booted from the DiskWorrior 3.0.3 CD to rebuild the directories of both volumes, 'I1232GB' & 'I2232GB'.
Still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
Downloaded the Mac OS X 10.2.8 Compo Update (for PPC) and installed it onto both 'I1232GB' & 'I2232GB' while booted from the eDrive which I keep on Mac OS X 10.4.7 - no luck either, still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
Then I backed up the users folder from 'I2232GB' onto 'I1232GB', booted from Mac OS 9.2.2 and used Intech's Hard Disk Speedtools 3.6 to format 'I2232GB', afterwards initialized it with Alsoft's Plus Maximizer Extension for a Block Size of 512 Bytes.
Installed Mac OS X 10.4 from DVD, as well as iLive '06 and upgraded everything to the latest releases with Software Update. All was working fine with all the required reboots until another startup volume was chosen: afterwards again I can no longer boot back into Mac OS X 10.2.8 on the fresch installed 'I2232GB'!
Any help would be appreciated.
Here is some information found by System Profiler from Mac OS X 10.4.7, eDrive, let me know if you need more:
Hardware Overview:
Machine Name: Power Mac G4 (AGP graphics)
Machine Model: PowerMac3,1
CPU Type: PowerPC G4 (2.8)
Number Of CPUs: 1
CPU Speed: 450 MHz
L2 Cache (per CPU): 1 MB
Memory: 2 GB
Bus Speed: 100 MHz
Boot ROM Version: 4.2.8f1
Serial Number: XA00715VHSF
Sales Order Number: M7628LL/A
ATA Bus:
IBM-DPTA-372050:
Capacity: 19.12 GB
Model: IBM-DPTA-372050
Volumes:
IBM_18GB:
Capacity: 13.12 GB
Available: 6.96 GB
eDrive:
Capacity: 6 GB
Available: 3.03 GB
IBM-DTLA-307075:
Capacity: 71.59 GB
Model: IBM-DTLA-307075
Volumes:
IBM_71GB:
Capacity: 71.59 GB
Available: 39.65 GB
ATA Bus:
PIONEER DVD-RW DVR-107D:
Model: PIONEER DVD-RW DVR-107D
Firmware Revision: 1.21
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
IOMEGA ZIP 100 ATAPI:
Model: IOMEGA ZIP 100 ATAPI
ACARD,6880M:
Name: ACARD,6880M
Type: scsi
Bus: PCI
Slot: SLOT-C
Vendor ID: 0x1191
Device ID: 0x0009
Subsystem Vendor ID: 0x1191
Subsystem ID: 0x0009
Revision ID: 0x0003
SCSI Parallel Domain 65536:
Initiator Identifier: 7
ATA HDT722525DLAT80:
Capacity: 232.89 GB
Manufacturer: ATA
Model: HDT722525DLAT80
Revision:
Removable Media: Yes
BSD Name: disk2
OS9 Drivers: Yes
SCSI Target Identifier: 0
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
Volumes:
I1232GB:
Capacity: 232.89 GB
Available: 14.1 GB
Writable: Yes
File System: HFS+
BSD Name: disk2s3
Mount Point: /Volumes/I1232GB
ATA HDT722525DLAT80:
Capacity: 232.89 GB
Manufacturer: ATA
Model: HDT722525DLAT80
Revision:
Removable Media: Yes
BSD Name: disk3
OS9 Drivers: Yes
SCSI Target Identifier: 2
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
Volumes:
I2232GB:
Capacity: 232.89 GB
Available: 180.11 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk3s3
Mount Point: /Volumes/I2232GB
The RAM consists of 4 identical modules and is about 1 year old:
DIMM0/J21 to DIMM3/J24:
Size: 512 MB
Type: SDRAM
Speed: PC133-333
Status: OK
Many thanks for your help!
Josef
Apple G4 AGP Mac OS X (10.4.8) 4 internal hard disks, dual layer DVD-RW, 2GB RAM

What I did so far: 'I2232GB' was my main OS X
startup volume, 'I1232GB' contains a clone of it,
plus additional folders like software base and
backups.
After upgrading 'I2232GB' to Mac OS X 10.4.8
through Software Update and repairing permissions all
was OK as long as the Mac was just shut down or
re-started: it always booted up in Mac OS X 10.4.8
from 'I2232GB' without any problems.
The next day I booted from 'I1232GB' to do the same
there.
Afterwards I could no longer boot in Mac OS X 10.4.8
from 'I2232GB' nor in in Mac OS X 10.4.8 from
'I1232GB': it just gets to the grey screen with the
Apple logo, but the round circle underneath
indicating some progress never appears. I left it
there for hours: it just hangs.
With the Option key held at startup I could boot from
the other partitions with Mac OS 9.2.2 or the eDrive
with 10.4.7. None of their Startup Control Panels was
able to get me back to 10.4.8!
So I booted from the TechTool Pro 4.5.1 DVD to
Optimize both volumes, 'I1232GB' & 'I2232GB',
always Files only.
Then I booted from the DiskWorrior 3.0.3 CD to
rebuild the directories of both volumes, 'I1232GB'
& 'I2232GB'.
Still I can not boot from either 'I1232GB' or
'I2232GB' in Mac OS X 10.4.8!
Downloaded the Mac OS X 10.4.8 Compo Update (for PPC)
and installed it onto both 'I1232GB' & 'I2232GB'
while booted from the eDrive which I keep on Mac OS X
10.4.7 - no luck either, still I can not boot from
either 'I1232GB' or 'I2232GB' in Mac OS X
10.4.8!
Then I backed up the users folder from 'I2232GB'
onto 'I1232GB', booted from Mac OS 9.2.2 and used
Intech's Hard Disk Speedtools 3.6 to format
'I2232GB', afterwards initialized it with Alsoft's
Plus Maximizer Extension for a Block Size of 512
Bytes.
Installed Mac OS X 10.4 from DVD, as well as iLive
'06 and upgraded everything to the latest releases
with Software Update. All was working fine with all
the required reboots until another startup volume was
chosen: afterwards again I can no longer boot back
into Mac OS X 10.4.8 on the fresch installed
'I2232GB'!
I found several typos in above post, wherever it was 10.2.8 it should have read 10.4.8 - I'm very sorry for confusing you, this would not have made sense, but I found no way to edit the existing text therefore I modified the quote of it here.
I do not need Mac OS X 10.2.8 back, but it would be nice to boot back in Mac OS X 10.4.8 from another volume as the current one - which was working fine before with Mac OS X 10.4.7.
Many thanks,
Josef

Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format

I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
So to sum up, the symptoms I'm seeing:
MacBook Pro CAN see internal SATA hard drives.
MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.

UPDATE: An interesting development!
I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
Onward!

Will Not Boot from Install Disc & 4SNS/1/40000000: TG0D - Thermal Sensor?

*Will Not Boot from Install Disc*
I used the "option key" approach with the gray start up disk. At first it ejected the start up disk. Then I nudged the disk back in the machine and it showed on the screen as an option. I clicked on the start up disk image and it finally loaded.
But, it won't accept the start up disk when holding down the "C" key at restart.
*4SNS/1/40000000: TG0D*
I did an Apple Hardware Test and received the following diagnostic:
Version: 3A121
Test Suite: Extended Test
Loop Count: 2
Result: Failed
Failure code: 4SNS/1/40000000: TG0D
*Thermal Sensor*
A search for the failure code 4SNS/1/40000000: TG0D brought up an Apple Discussion topic entry stating: That error code indicates a problem with a thermal sensor. It could be not working or possibly not connected. You will need to take it to Apple for repair.
Would a thermal sensor have anything to do with it not starting up when holding down the "C" key at restart? What are thermal sensor problem symptoms?
*User File Folder Opened Up*
The machine also starts up with my user file folder opened up rather than with a blank screen as it normally should
I completed a DiskWarrior rebuild on the disk and verify disk shows it is fine.
Any suggestions on what to do next with these issues?

The answer was in your post: "You will need to take it to Apple for repair."

Can not boot from OSX disc

I recently partitioned my internal drive with an 80 gig partition to run Ubuntu , removed Ubuntu and now can not resize hd to recover the 80 gig that I used , there was a program with this Ubuntu install called rEFIt that was installed for the dual boot , My problem is that Itunes keeps crashing and I have spent somewhere around 8 hours trying to fix this issue and in the process I discovered that I now can not boot from the osx disc but I can boot from the Ubuntu disc , what can I do to correct this issue or is there anything that I can do to correct this and recover the 80 gig that I used ?

The only solution was to erase hd and restore from time machine backup......
According to everything that I have seen , read and tried when you partition the mac hd the way that mac is designed it will lock the hd thus preventing any access even using the startup disc to repair. As far as restoring everything after the erase and reinstall of the OSX that was easy and painless. FOR ANYONE WHO DOES NOT BACKUP THEIR DATA THIS IS WHY YOU SHOULD!!!!
Once OSX is reinstalled the migration assistant will ask if you want to restore from a backup , if you have time machine or any other sort of backup simply choose the one you wish to restore from and continue , must admit I was a bit hesitant at first , I must say that everything restored with the exception of some settings that I have had to restore but they were not major settings , after the backup is restored simply run update check and reinstall all updates , may need to do this a couple of times.
Depending on the amount of data you have will determine the length of time for restore (500 gigs about 6 hrs.) but it will restore user account settings , connection settings and network settings.
Hope this will help if anyone has experienced the same problem.

G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD

We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
We were in the process of installing 10.4 Tiger before placing it for sale.
The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
We have done the following during our troubleshooting:
- Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
- Remove RAM 1 stick at a time and reboot
- Replace RAM with RAM from another working Quicksilver
- Replace Video Card with one from another working Quicksilver
- Zap PRAM
- Reset CUDA switch
- Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
- Tried booting from the Macintosh Server G4 Software Restore CD
- Tried booting from Mac OS X Server CD
- Tried booting from AppleCare Protection Plan CD with TechTool
- Tried booting from Diskwarrior CD
- Tried booting from an external FireWire drive with a disk image of Tiger OS Install
- Tried booting with the hard drive disconnected
The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.

Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
I would look at the CD drive cables, etc, and see if another drive gives different results.
You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
HT1310- Startup Manager: How to select a startup volume

IMac will not boot from any mode except Target Disk

I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot, and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
I reformatted the HD and installed 10.7 again, it still freezes up at the same point.
I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
UPDATE...
Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own. I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
I did manage to have it start one time got a copy of the the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
Specs...
The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
Error Report…
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

Here is the complete error log...
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80602db800 : 0xffffff801a41d5f6
0xffffff80602db870 : 0xffffff801a4b7b95
0xffffff80602dba40 : 0xffffff801a4ce4ad
0xffffff80602dba60 : 0xffffff7f9bab8654
0xffffff80602dbb60 : 0xffffff7f9baa218c
0xffffff80602dbbb0 : 0xffffff7f9baa20e2
0xffffff80602dbbd0 : 0xffffff7f9ba73554
0xffffff80602dbc00 : 0xffffff7f9aa8d470
0xffffff80602dbc40 : 0xffffff7f9aa8d3df
0xffffff80602dbc60 : 0xffffff7f9aa926ec
0xffffff80602dbcf0 : 0xffffff7f9aa8af20
0xffffff80602dbd20 : 0xffffff7f9aadacc7
0xffffff80602dbd70 : 0xffffff801a833b9b
0xffffff80602dbdc0 : 0xffffff801a862d57
0xffffff80602dbe30 : 0xffffff801a497cef
0xffffff80602dbe80 : 0xffffff801a420abd
0xffffff80602dbeb0 : 0xffffff801a410448
0xffffff80602dbf00 : 0xffffff801a4195fb
0xffffff80602dbf70 : 0xffffff801a4a5ad6
0xffffff80602dbfb0 : 0xffffff801a4ced13
      Kernel Extensions in backtrace:
         com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
         com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
         com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
            dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
12B19
Kernel version:
Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
Kernel slide:     0x000000001a200000
Kernel text base: 0xffffff801a400000
System model name: iMac8,1 (Mac-F227BEC8)
System uptime in nanoseconds: 26349024446
last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
loaded kexts:
com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
com.apple.driver.AppleHDA          2.3.0f2
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.filesystems.autofs          3.0
com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
com.apple.driver.AppleLPC          1.6.0
com.apple.driver.AppleMuxControl          3.2.6
com.apple.driver.AppleBacklight          170.2.3
com.apple.driver.AppleUpstreamUserClient          3.5.10
com.apple.driver.AppleMCCSControl          1.0.33
com.apple.GeForce          8.0.0
com.apple.driver.AppleSMCPDRC          1.0.0
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.ApplePolicyControl          3.2.6
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleIRController          320.15
com.apple.iokit.SCSITaskUserClient          3.5.1
com.apple.driver.AppleFileSystemDriver          3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.2.1
com.apple.driver.AppleFWOHCI          4.9.5
com.apple.driver.AppleUSBHub          5.1.6
com.apple.driver.AirPortBrcm43224          600.36.17
com.apple.iokit.AppleYukon2          3.2.3b1
com.apple.driver.AppleAHCIPort          2.4.0
com.apple.driver.AppleIntelPIIXATA          2.5.1
com.apple.driver.AppleUSBEHCI          5.1.5
com.apple.driver.AppleUSBUHCI          5.1.5
com.apple.driver.AppleEFINVRAM          1.6.1
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleHPET          1.7
com.apple.driver.AppleACPIButtons          1.6
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.6
com.apple.driver.AppleAPIC          1.6
com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2
com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
com.apple.driver.DspFuncLib          2.3.0f2
com.apple.iokit.IOAudioFamily          1.8.9fc9
com.apple.kext.OSvKernDSPLib          1.6
com.apple.kext.triggers          1.0
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.nvidia.nv50hal          8.0.0
com.apple.NVDAResman          8.0.0
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.AppleHDAController          2.3.0f2
com.apple.iokit.IOHDAFamily          2.3.0f2
com.apple.iokit.IOSurface          86.0.2
com.apple.iokit.IOBluetoothFamily          4.0.9f8
com.apple.driver.AppleGraphicsControl          3.2.6
com.apple.iokit.IONDRVSupport          2.3.4
com.apple.iokit.IOGraphicsFamily          2.3.4
com.apple.driver.AppleSMC          3.1.3d11
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.IOPlatformPluginFamily          5.2.0d16
com.apple.iokit.IOUSBHIDDriver          5.0.0
com.apple.driver.AppleUSBMergeNub          5.1.5
com.apple.driver.AppleUSBComposite          5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOATAPIProtocolTransport          3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOUSBUserClient          5.0.0
com.apple.iokit.IO80211Family          500.15
com.apple.iokit.IONetworkingFamily          3.0
com.apple.iokit.IOAHCIFamily          2.2.0
com.apple.iokit.IOATAFamily          2.5.1
com.apple.iokit.IOUSBFamily          5.1.6
com.apple.driver.AppleEFIRuntime          1.6.1
com.apple.iokit.IOHIDFamily          1.8.0
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          344
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.18
com.apple.driver.AppleACPIPlatform          1.6
com.apple.iokit.IOPCIFamily          2.7
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
Parallel ATA Device: MATSHITADVD-R   UJ-875
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
USB Device: Trackball, 0x046d (Logitech Inc.), 0xc404, 0x1d120000 / 4
USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

Router was not booting from flash

Similar Messages

Maybe you are looking for