Router web page not working

My dad has a WRT54GS that we can't get the WEP key set. We can get onto the router site but when I click on the wireless tab it goes to an empty page. I thought it may be popups so I turned all that stuff off but it didn't work. Can anybody help me? Thanks

To view the router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

Similar Messages

827H router web setup not working

We were having problems with our 827H router, so I decided to reset it to the factory defaults and re-run the quick setup. I've done that before with no problems.
This time, after it loads the configuration in the web setup, it keeps checking the model, IOS version, etc.--over and over again. It won't stop, nor can we exit out of it to get to the quick setup.
Originally the router was connected to a hub. When we couldn't configure it from the web setup, we put the router directly onto a pc with an ethernet cable. We could ping the router. Using the console cable, we are able to see the router's settings. (See attached)
The pc was set to dhcp. The dns was originally set to "Obtain automatically". We also tried to set the dns and the gateway to the router's ip, and added the domain controller's dns as another dns server. Nothing has worked.
Any help will be greatly appreciated.
Thanks!

Your description of the symptoms is quite puzzling as is the console log that you sent. You say that you connected a PC directly to the router. Was that using a cross over Ethernet cable?
You say that when you connected the PC to the router you could ping the router. What IP address was on the PC at that point.
The console output that you included has a kind of garbled output in the show run. It looks as if two things were outputting at the same time. I am not clear if there were actually two things happening together or if the router is really messed up. (Though most of the config that showed up looked reasonable)
I would suggest that you connect to the console port again and capture all of the console output. I would suggest that whle you are connected and capturing output that you power cycle the router (it may be very helpful to see what messages go to the console while the router is booting).
After the router boots again, you may be able to use the web interface. If the web interface does not work you should be able to use the console interface to get a congif that should work basically.
Try these steps and post the output. Maybe then we can find a solution.
HTH
Rick

EA4500 router web page not accessible for use.

I cannot login, web page pops up but its only a blue screen with help icon and privacy icon at bottom nothing is interactive. Have tried mylocalrouter.com, linksyssmartwifi.com. When uninstall software, hard reset router then reinstall software I get to the the login icon but when try to login it shows blue screen as previously mentioned in message. Router works but at a reduce speed and cannot manage any options. Tried updating firmware but once I unzip there is no way to install the .ssa firmware file

Hi mtebaldi, have you tried using another browser and computer? If you're using a wireless computer, you may also try to turn the wireless computer WiFi switch to off then connect it directly to the router using an Ethernet cable. Once done, reaccess UI again. You may also try to access UI using "myrouter.local".

Web pages not working

When I load a p0age from lightroom's web module. They don't work properly.
1) the directorys are wrong It's lin the first line.
2) it won't load the large image to be viewed on my web page
3) some of the line are looing for flasf and some are looking for adobe flash which seems to creat another problem keeping them from not working
I use a MAc computer

OK, that's much better. This looks like an odd error that has been seen with some types of server configuration. I can't recall exactly what caused it, but I think you could get round it by not including a logo.
Take a look at http://www.bluefire.tv/blog/FlashGalleries/headerfix.html and other postings on that blog. These guys designed the Flash galleries for Adobe. Also search back in this forum and in the LR forum at Luminous Landscape. It has definitely been discussed - look out for postings by Micah Bowers who is part of Bluefire. Hope this helps.
John

Oracle 8i online docs web pages not working in IE5.5?

Up until about a week ago, I was able to browse the online docs for Oracle 8i, using Internet Explorer 5.5 SP2 on Windows 2000 SP2. Now, I am getting incomplete web page loads and/or pages that repeatedly reload themselves. I do not experience this problem browsing the same pages with Netscape 6.2 on the same PC. The only relevant change on my PC I can think of was application of Service Pack 2 to Internet Explorer 5.5.
An example URL is http://technet.oracle.com/docs/products/oracle8i/doc_library/817_doc/server.817/a76965/c01intro.htm#12981 - this page loads only down to the section "Data Integrity". Other pages exhibit similar behaviour. I don't experience this problem using IE5.5 with any other Web sites.
I have tried clearing all cookies, cached files, etc. to no avail.
Any help or suggestion will be appreciated.
Regards,
Philip Steiner

Hi,
You need to follow below steps:
1) cd $JAVA_TOP
    2) zip -r customprod.zip. Where the list of all directory paths are present, relative to $JAVA_TOP, for custom application's java files at non-standard location.
    3) Generate & sign customprod.jar file.
Command: adjava oracle.apps.ad.jri.adjmx -areas $JAVA_TOP/customprod.zip -outputFile $JAVA_TOP/customprod.jar -jar $CONTEXT_NAME 1 CUST jarsigner -storePass -keyPass
    4) Delete temporary customprod.zip.
Command: rm $JAVA_TOP/customprod.zip
    5) Follow below steps to make the custom jar available for WebLogic
a) Take a back-up of existing /admin/template/ebsProductManifest_xml.tmp
b) Modify /admin/template/ebsProductManifest_xml.tmp to add entry for customprod.jar (after customall.jar)
c) Run AutoConfig
d) Bounce the Mid-tier services
Thanks,
Anupam

Web page not working for vi when launched from testsetand

we've setup a web page for a vi in labview (web publishing tool) and its visible in IE until you close labview
this vi is then run from teststand thou the web page isnt being updated?
we need to be able to view the contents of the vi remotely

Hi,
Would it be possible for you to upload either the programs that demonstrate this (if not too large) or quickly create a program and run instructions in order to replicate this behaviour here? Also which versions of TestStand and LabVIEW are you running?
Once I have this extra information and code I will replicate the issue here and look into it further for you,
All the best,
Applications Engineer

Web page not working.

HI Im new to the forum. I have had a web site for about 2 years and for the first time I have had a problem with my web page. I can publish when done adding picture etc but when I go to look at the web site it is not there. Here is what I thought all along is my web address but I am not so sure anymore.
http://web.mac.com/yiotta55/sljewelrydesign/WELCOME_.html
I also tried web.mac.com/yiotta55 and nothing. Im pretty bad at this kind of stuff and am hoping that someone can give me a hand and tell me what to do?
Thanks so much

What's not there, the picture or the site? If it's just the picture then clear your browser's cache files and then reload the site. The both links you gave loaded OK for me, Simple Brass Tools for the Glass Artist.
Give the cache cleaning a try.
OT

Chat Support web page not working

Can anybody tell me when it is expected that the chat support page for smart storage / small business warranty support will be fixed.
https://supportforums.cisco.com/community/netpro/small-business/sbproductwarranty It broke about 2 - 3 weeks ago and whilst I am being told that it does operate if you have Firefox or Chrome Internet Explorer 9 is not supported! The second drop down list is non functioning.
I find this unbelievable. I thought that IE was the most used browser (I appreciate some people do not like it) and the fact that Cisco have not accommodated this product when supposedly designing their support web pages worries me, as I use IE and have just purchased some Cisco hardware / software.
Kriss

Dear Cindy
Thank you for your reply. But I think the issue is related to software, as I feel that the web page support provided by Cisco, is part of the overall package which I purchased. In unrelated areas I have also had to turn on compatibility view in IE9 to gain correct access to elements of the hardware of my CISCO product, therefore the hardware has also been indirectly affected.
Surely the new support web page was tested prior to going live? cant you put the old page back until you sort this out? I appreciate these are simplistic statements but you can see my point of view.
My original question is how long will it take to put right the defect in the support web pages?.
Kind Regards
Kriss

Why does Create PDF from Web Page not work with certain URLs?

I'm creating a large number of PDFs from Web Pages on Adobe Acrobat XI Pro and occasionally come across certain URLs that fail to generate a web page. The process begins as normal but eventually the status window lists a few errors or canceled processes and that there are now 0 Connections Active. This only occurs for certain URLs, but when it happens it consistently fails for that URL (as in trying it a few mroe times doesn't let it work). Is there any specific reason this happens or a way I can prevent it? The above example is of a URL that fails to generate a PDF :
http://www.pcmag.com/encyclopedia_term/0,1237,t=access+point&i=37393,00.asp

I tested this in Acrobat X and the exact same issue occurs
http://www.quantumdynamix.net/clients/image-map-test/ImageMapTest-AcrobatX.pdf
This has to be considered a legatimate bug, especially since IMAGE MAPS is listes as one of the supported HTML features via the help files

Recovery media kit order web page not working for Canada site

The laptop crashed (Pavilion G6-2288ca with Windows 8). I'm planning to replace the hard drive. I want to order the recovery media kits from hp but the Canada site is not working. After I entered the postal code, the site says it is temperarily out of service. I tried the same on the US site with a pretended zipcode and it worked fine. Can someone please help?
Thanks.

Try phoning HP Support. 1-800-474-6836
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Software Update web page not working

For several days I can't access the "device software update" web page. I click on Get Started with the intention to download the NSU but the page is contentless.
Is anyone experiencing such an issue? Any suggestions?
Solved!
Go to Solution.

Hi pepelyankov
There is no problem at time of post with download here:
http://europe.nokia.com/A4579163
Happy to have helped forum in a small way with a Support Ratio = 37.0

Sending a web page not working

I usually send web pages as a link only, but this time i want to send the whole page. I know the Mac can do this, because I've done it before. Now, when I try to sent the web page with "Send Web Content As: Web Page" selected, I get the endless spinning gear with "Loading..." next to it. What's up?

This is more serious than I thought.
I tried to restart Mail to see if it would fix things, and got this:
And, there are 2 Mail icons in the Dock, neither of which will do anything:

Cisco asdm web page not working

yes i have

hello,
i have a cisco ASA 5505 with os version 8.4(5) and asdm 7.1(1)52.
i do enable http server.
i luch asdm image
i checked if the http port is open (it is)
but i can't acces the web page of asdm.
any suggestions?
thank you
This topic first appeared in the Spiceworks Community

Router web page not showing correctly

I use WRT54G wireless router. When trying to change options on my router, I go to 192.168.1.1 in a browser and put in my password. When the site opens, it resembles what it is supposed to look like but is kind of messed up. Here is a picture of what my page looks like: http://img383.imageshack.us/my.php?image=linksysbb5.png With it like that it is almost impossible to change anything. I'm not sure what's wrong. I've looked around for help on the web but most of the things I've found is people who just can't even connect to the site. By the way, I don't know if this has anything to do with it but when running the CD to hookup the modem, once it gets to the part where it asks for the password, I put it in and once the loading bar comes up I get a pop-up saying I have low or no internet connection for a second or two then goes away. It continues to load but nothing happens and eventually the password thing pops up again and it starts all over. Any help is appreciated, thanks.
Message Edited by pb93 on 03-08-2008 09:41 AM

I'm not sure but could the problem possibly be with the router itself. I checked many other topics of people reporting the same problems as me and the person above me. They all seem to be the same WRT54G wireless routers and all seem to have been reported at least within the last couple weeks. It seemed like the help given too never really helped the problem. I'm sure it's not the browser because I have had the same result on all that I've tried or the firewall because I have had that off while trying just like everyone else who seemed to have the problem.

Safari email web page not working

I'm trying to use Safari to create an HTML email. I've made a page which is on my Me server but when I use Safari to email it it doesn't work. The page displays perfectly in my send window in Mail but the subsequent email arrives empty. What am I doing wrong?
My page is here: http://web.me.com/hayesdavies/jane/febpage.html
Thank you

Yes. But both are in Mail so it went from one to the other in Mail and the second one gets nothing. It works in Entourage but I get a "this message is in MIME format, since your mail reader does not understand this format" etc error which is no good either.

Router web page not working

Similar Messages

Maybe you are looking for