Routers that work with iChat AV?
Since Apple's list of approved routers hasn't been updated for years, I would love to hear from anyone who has purchased a router recently that works with iChat for audio/video, including any special setting changes/tips. Could anyone with a success story post here? I'm tired of the error 8 messages which in at least some cases seems to be router related.
@stevesol
I have used the DI-604 for about 5 years now. It is a great and cheap router/firewall. The only problem that I have ever had was an odd one. I have a mac pro. i have an external amp that I use for playing my music through. I had a cable run from the rear audio out to the amp. After the last firmware update (mac pro EFI firmware update 1.1) I could not use ichat anymore. If I bypassed the router and went straight to the modem then all was fine. It turned out that there was a major conflict with my setup using the router and rear audio out port but if i used the front headphone jack everything was fine. Other than that the DI-604 is very good. I open port 5190 on the router and have good results. If you are not sure how to open up ports then check out this site. It shows to open up a whole pile of ports but the 5190 port works fine for me.
http://www.portforward.com/english/routers/port_forwarding/Dlink/DI-604/iChat.ht m
I would also recommend this fine site from one of the other posters. Ralph Johns site is excellent
http://www.ralphjohnsuk.dsl.pipex.com/page2.html
and of course what Apple has to say about their firewall
http://docs.info.apple.com/article.html?artnum=93208
Similar Messages
-
What type of external webcam works with iChat?
Is there a certain type of external webcam that works with iChat or can any webcam do the job?
Logitech Quickcam Vision pro for the Mac was recently released and I am using it with G5 QUAD and OS X 10.5.4 without problems. It is quite expensive compared to other cameras but it has a Zeiss lens and I think a much better picture. Works with evocam also. (evocam is a shareware program to do time lapse photos, or motion sensor movies and webcam stuff). I'm very happy with it.
hth,
vince -
What is best mobile platform/os that will work with iChat? (pda/phone?)
hey dudes,
i was looking for a new smart phone that could use or work with some type of iChat client?
can anyone suggest a phone/pda that works well for them?
the 3 phones i have shortlisted so far are Treo 700p (but it isn't available in the UK yet), Nokia N-series phones, N92 or N93 maybe?
or as a last resort the HP hw6515 with GPS and wi-fi...
is working with iChat even possible?
thanks dudes!
http://NoteToSelfDontDie.comok, just found this thread...
http://discussions.apple.com/thread.jspa?messageID=2540185�
this dude says he uses the Nokia N80 - these phones use the Symbian OS...
interesting.... -
How do I Get My Router to Work With iChat ? FAQ 2
Replaces iCh: FAQ 2 How to get my router to work with iChat?
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have.
Routers seem to fall into two categories
Those that work straight from the box. See Apple Doc 93333
NOTE
This Doc has not been updated since Jan 04
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255).
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
DMZ Demilitarised Zone
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN)
NAT Sometimes called NAPT and related to Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You will need to set an incoming IP address (Usually 0.0.0.0 for any outside server), a port that data will arrive on, the Inside computers IP address (your computer) and the port it will deal with the data on and the protocol it will use.
iChat uses TCP and UDP so some devices will need the settings done twice, once for each protocol.
See Apple Doc 93208 for more information.
Note:
Note 1 should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, which need to be open for TCP only.
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678. When you click on the invite window the process moves to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP
Wireless
Here you will have to read around but this Apple Doc 58514 might be a good starting place.
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my pesonal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding.
Ralph
G4 Dual 1Ghz MDD with extra HDs X3. Mac OS X (10.4.3) Have you read the iChat FAQs ?? They have moved to Users TipsReplaces iCh: FAQ 2 How to get my router to work with iChat?
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have.
Routers seem to fall into two categories
Those that work straight from the box. See Apple Doc 93333
NOTE :This Doc has not been updated since Jan 04
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
DMZ Demilitarised Zone
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN)
NAT Sometimes called NAPT and related to Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You will need to set an incoming IP address (Usually 0.0.0.0 for any outside server), a port that data will arrive on, the Inside computers IP address (your computer) and the port it will deal with the data on and the protocol it will use.
iChat uses TCP and UDP so some devices will need the settings done twice, once for each protocol.
See Apple Doc 93208 for more information.
Note:
Note 1 should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, which need to be open for TCP only.
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678. When you click on the invite window the process moves to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP
Wireless
Here you will have to read around but this Apple Doc 58514 might be a good starting place.
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my pesonal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding.
With thanks to Macmuse.
Ralph
G4 Dual 1Ghz MDD with extra HDs X3. Mac OS X (10.4.3) Have you read the iChat FAQs ?? They have moved to Users Tips<</a>/span> -
Update to kichat: FAQ 2 - How to get my router to work with iChat?
kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008 -
USB Camera does not work with iChat
Hello,
I'm having a terrible time getting my ToUcam Pro II to work with iChat. I downloaded the iUSBcam program. That didn't work. I downloaded the program Macam, and copied the proper file into the Quicktime Library (as suggested) and that didn't work. I downloaded IOXwebcam, and got an error stating that it wouldn't run due to the fact that it didn't have the proper security settings. Sigh.
So... what am I to do?
I'd like to buy a webcam that does, actually, work with my 8 month old Mac Pro 4 core mac desktop, but the iSight camera is ridiculously expensive. Any other suggestions would be appreciated.
BradAn X-box 360 cam will do it although not in that list.
Anything that is USB 2.0 and marked UVC compliant or Vista Certified.
Be Aware some Mac Keyboards do not have USB 2.0 ports.
11:57 PM Tuesday; September 8, 2009 -
PC Webcam works with iChat and iSight
Before I purchase a web cam for my PC I need to know if it will work with iChat and iSight. Will I need to install any third party software for my mac or PC?
Hi Gene,
You will need to make a choice between AIM and Trillian
The AIM app is free but does not Audio only Chat to iChat users and has a very small pic.
Trillian costs $25 for the Pro version to Video chat but has a Bigger pic and can do full screen. The Basic version can alos Audio only chat to iChat users. Trillian can also join other IM services.
More info on setting up AIM on the PC http://www.ralphjohnsuk.dsl.pipex.com/page12.html and the XP Service Pack 2 firewall. The Firewall will need to have Trillain enabled though it as well if you use that.
Ralph -
I have an airport extreem network that works with my two MacBooks and a iMAC. I am having no luck in getting a PC (IBM ThinkPad0 that has the PC airport software to be recognized by the network. Any suggestions?
When you introduced the AirPort Extreme, you had a condition where you have two routers in series. The simpliest solution is to reconfigure the downstream router (in this case the Extreme) as a bridge. This will allow the upstream router to provide the required NAT & DHCP services to all network clients regardless of which router they are connected to.
To reconfigure the Extreme as a bridge, you will use the AirPort Utility. (Note: I will provide the steps for using AirPort Utility v5.x)
AirPort Utility > Select the AirPort > Manual Setup
Internet > Internet Connection tab > Connection Sharing = Off (Bridge Mode) -
Which USB Webcams will work with iChat?
Hi,
I'm new to these forums and am wanting to get a webcam, but iSights are no longer available and I don't have the interest or money to get a DV Camcorder.
So which USB webcams will work with iChat?
I take it I'll also have to purchase iChatUSBcam or whatever it's called.
Thanks
IainHi Iain:
There is a list of cams on their website:
http://ecamm.com/mac/ichatusbcam/configs.html
The only USB cam that doesn't require iChatUSBCam is the iMage.
-Ken -
Video & Voice Chat Not Working With ichat
Voice Chat and Video Chat is not working with ichat 6 in booth google and yahoo. One side is ichat and the other side is yahoo & google talk clients, Please confirm whether its a workable scenario or it only supports ichat to ichat.
Thanks & Regards
Sreejith RHi
Other alternatives based on the amount of info in your post.
Has she set up her Google Name in iChat or is she logged on via the Web Site (Google Mail page) ?
iChat cannot Video to the Google Mail Login page chat option or to the app called GoogleTalk on a PC.
Another thing.
If you login to the GoogleMail Web pages you will get logged out of iChat (GoogleTalk account) to a partial extent which may explain the loss of Video or Audio iCons.
iChat reports in a Text chat window that you have Logged Off.
However you seem to be able to continue the chat - but it separate from the web Page chat - You send from the web page and that chat will get the next response, send from iChat and it gets the next response (I can't remember if the Buddy told me he got two Chat windows at his end)
9:26 PM Wednesday; May 12, 2010
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat" -
I would like to know if it is possible to use ichat on my mac to communicate with someones Ipod or Iphone with facetime?
Thanks in advance for any help here.jwg777 wrote:
I would like to know if it is possible to use ichat on my mac to communicate with someones Ipod or Iphone with facetime?
Thanks in advance for any help here.
(1) FaceTime cannot work with iChat.
*FaceTime ONLY works with other FaceTimes*:
• iPhone 4 http://www.apple.com/support/iphone/facetime/
• iPod touch Gen4 http://www.apple.com/support/ipodtouch/facetime/
• FaceTime (beta) on iNtel Mac w/OS X 10.6.4 or later http://www.apple.com/mac/facetime/
*FaceTime works with _NO OTHER_ app from Apple, Skype, or anyone else*.
(2) You do not tell us which imac you use, so we cannot give a yes or no answer to your question about whether it is possible to use ichat *_on your mac_* to communicate with someones iPod or iPhone with facetime.
The answer to your question is yes, FaceTime is possible, but *ONLY IF* your Mac is an iNtel Mac that is using Snow Leopard (OS X 10.6.4 or later) with the FaceTime beta application software.
EZ Jim
Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.6); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.6)
LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod4touch4.2.1 -
How can I make an icon that links to a webpage that works with Mac and Windows??
Hi!
I burn CDs with my photos and send them to clients. Besides the photos folder, I would like to include a file (similar to the .webloc files on the Mac Desktop) that can be clicked and it will be linked to my website - it will open up a browser window and go to my website . Is it posssible to make one of these icons that works with both Macs and Windows machines? Thanks!Now it works! Thanks, Denico!
The reason I saved to text: The first time I followed your instructions, it did not work. I tried to figure out what I did wrong and saw that you wrote to "save as plain text." I did not know what this means and there was no option available to save a plain text. So I looked around and saw "save as stationery" and I guessed that maybe that was what you meant. And after that, it worked! But the next thing you know, the icons started duplicating themselves.
I guess I had made a different mistake in the beginning and I fixed it without knowing what it is.
Thanks for clearing that up.
But just one question. WHY does saving as "stationery" make an icon duplicate itself? -
I've tried 3 UPS's (2 APC and one TripLite) that state they are OSX compatible, however, they do not fully respond to the native osx setting in (system Preferences/ Energy Saver/ UPS/Start up automatically after a power failure). This is what happens:
During a power outage, the OS does a graceful shutdown, but does not reboot when power is restored.
Apparently, the UPS is not notified to turn off during the shut down process. The power (on-Off-On) cycle is required by the mac to restart.
Trip lite tech support says they have software that works with Windows and linux to do this, but not mac.
I've tried two older APC UPS's, One Smart UPS1500 and a Back-UPS 1500 with the same result on two different servers and one iMac.
At this point I'm looking for a make and model of a UPS that does work. If anyone can verify a make and model that actually does this, I'd greatly appreciate it.
Its a simple test, just pull the plug on your UPS, wait for the system to shut down, and then plug the UPS back in. The system should reboot.Many of the CyberPower UPS units are compatible. Checkout the home solutions on this page: http://www.cyberpowersystems.com/products/ups-systems.html
-
I just upgraded to os 10.9.5 on my 15 " macbook pro from os 10.7.5. When I try to open iPhoto, I get the message that it is not compatible with the os. How can that be??? It came with the upgrade. It says the version of iPhoto is 9.3. How do I get an iPhoto that works with os 10.9.5? TIA
This screenshot shows which previous versions of iPhoto are compatible with Mavericks. It also indicates which versions qualify for a free upgradeto iPhoto 9.5.1 and which require a purchase:
Note 1: every day more users are reporting problems with iPhoto 8.1.2 so I've included it in the non compatible category.
Note 2: If your previous version of iPhoto was iPhoto 7 (08) or earlier you'll need to download and run the iPhoto Library Upgrader 1.1 application on the library before opening it with iPhoto 9.5.1 -
Looking for an app that works with Mac and iPhone that will set calendar reminders of birthdays in contacts.
Hi ron1098,
Try my application Dates to iCal. it runs on the Mac, but you can sync the calendar to your iOS device.
See more about Dates to iCal here. It is £4 shareware with a 2 week demo.
Best wishes
John M
As I sell software on my site and ask for donations, the Apple Support Communities Use Agreement requires that I state that I may receive some form of compensation, financial or otherwise, from my recommendation or link.
Maybe you are looking for
-
How do I get a package to mount (for guests) over network - so confused.
Folks we've got a 10.3.9 server I am trying to develop. I am trying to get a Filemaker Pro installer package available over the network so users can install it without giving them the license key - per the Filemaker instructions. The folder that cont
-
How do I make itunes 11 go back to playing my whole library after search
I just upgraded to iTunes 11. I'll search an artist just to find a song more quickly and double click on a song to play it. Then, I'll press x in the search box so it displays my library again, and in previous versions of iTunes after the song ended
-
I am wondering whether anyone can help me with this one please ? We have recently had massive problems with slow broadband speeds. We have home hub 1 so have had the hub for a while now and have never had a problem with speed until the last month or
-
Query related to Information broadcasting
Hi, I just want to know how many workbooks can be broadcasted at a given point of time to the users via email. How do i know if there is a limit to this option. Thanks.
-
Is there any plan on cleaning this forum up?
If not can anyone recommend another source for ARD discussion.