Routing from logic to spectral foo

I have installed the demo version of Spectral Foo (Stand Alone Application) on my PowerMac G5 (Audio Hardware: MOTU 2408mk3).
With the microphone input everything works fine, but I want also to analyze the main output from Logic with it. Has anyone experiences with this? Is it possible to route the main output from logic to the input of Spectral Foo?
PowerMac G5 Mac OS X (10.4.8)

If Spectrafoo is only a standalone application and doesn't run as a plugin, and just uses standard core audio to receive audio input, then you need to pipe the output of one application into another.
For this you'll need a virtual audio driver such as Soundflower or Jack. You route the output of Logic to your virtual driver, and use the virtual driver as the input to Spectrafoo.
You might want to create an agregate device in order to use both your main audio interface and the virtual ones together, as well, depending on your routing requirements.

Similar Messages

Where can i find the upgrade from logic pro 7.1.1 to 7.2?

Hello there.
Is the upgrade from logic pro 7.1.1 to 7.2 still available out there somewhere? I know I'm a bit behind the rest of the world but financially I'm taking the 'do the best with what you can' route!
Never used logic before, moving up from garageband and cubase sx cos everyone says it's a better program.
Many thanks,
GDx

Hi
If I remember correctly, the 7.2 update was a "Paid for" update, with a new dvd.... so you are most likely out of luck.
The good news is that Logic Pro is pretty cheap on the Appstore
CCT

UNABLE TO INJECT A STATIC DEFAULT ROUTE FROM PE????

UNABLE TO INJECT A STATIC DEFAULT ROUTE FROM PE????
Description:
I am unable to get a static default route via MPBGP session for a vrf, any other route redistributed the same way is getting through.
Just the static default route isn't ????
1>
SOURCE PE WHERE IS THE ROUTE REDISTRIBUTED:
pe1#
router bgp 4755
bgp router-id 10.10.10.103
no bgp default ipv4-unicast
bgp log-neighbor-changes
neighbor 10.10.10.100 remote-as 4755
neighbor 10.10.10.100 update-source Loopback0
address-family vpnv4
neighbor 10.10.10.100 activate
neighbor 10.10.10.100 send-community extended
exit-address-family
address-family ipv4 vrf B
redistribute static <<<<<<<<<<<<<< STATIC REDIS
no auto-summary
no synchronization
exit-address-family
address-family ipv4 vrf A
redistribute static <<<<<<<<<<<<<< STATIC REDIS
no auto-summary
no synchronization
exit-address-family
ip classless
ip route vrf A 0.0.0.0 0.0.0.0 Serial1/0 192.168.1.2 global <<<< STATIC ROUTE POINTING THE GLOBAL CONTEXT INTERFACE
ip route vrf B 0.0.0.0 0.0.0.0 Serial1/0 192.168.1.2 global <<<< STATIC ROUTE POINTING THE GLOBAL CONTEXT INTERFACE
DESTINATION PE HERE I CANNOT SEE THE STATIC DEFAULT ROUTE:
pe3(config-router-af)#do sh ip bgp vpnv4 all
BGP table version is 11, local router ID is 10.10.10.103
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 4755:1 (default for vrf A)
*>i172.16.1.0/30 10.10.10.101 0 100 0 ?
*>i172.16.2.0/30 10.10.10.102 0 100 0 ?
*>i172.16.10.0/24 10.10.10.101 2297856 100 0 ?
*>i172.16.20.0/24 10.10.10.102 2297856 100 0 ?
*>i172.16.200.0/24 10.10.10.102 2170112 100 0 ?
Route Distinguisher: 4755:2 (default for vrf B)
*>i172.16.1.0/30 10.10.10.101 0 100 0 ?
*>i172.16.2.0/30 10.10.10.102 0 100 0 ?
*>i172.16.10.0/24 10.10.10.101 2297856 100 0 ?
*>i172.16.20.0/24 10.10.10.102 2297856 100 0 ?
*>i172.16.200.0/24 10.10.10.102 2170112 100 0 ?
THE STAITC ROUTE IS REDISTRIBUTED TO LOCAL VRF CONTXT ASWELL AS WE CAN SEE:
pe3(config-router-af)#do sh ip route vrf A
Routing Table: A
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 192.168.1.2 to network 0.0.0.0
172.16.0.0/16 is variably subnetted, 5 subnets, 2 masks
B 172.16.200.0/24 [200/2170112] via 10.10.10.102, 00:00:23
B 172.16.20.0/24 [200/2297856] via 10.10.10.102, 00:00:23
B 172.16.10.0/24 [200/2297856] via 10.10.10.101, 00:00:23
B 172.16.1.0/30 [200/0] via 10.10.10.101, 00:00:23
B 172.16.2.0/30 [200/0] via 10.10.10.102, 00:00:23
S* 0.0.0.0/0 [1/0] via 192.168.1.2, Serial1/0
Hope I am clear in explaining the issue...
Thanks,
Dara

Hehehe :)
"Unfortunately" that's true !!!!
This could have been the last thing that I try.
Getting he techs work, protocols work is fine.
But if get to make myself understand the logic behind adding this command as well than ... :(
Thanks a lot,

HD video out from Logic - possible?

I have been trying to find if there is a way to get HD video out to an external monitor from Logic. Tried a Decklink "Intensity" card, wouldn't output HD. I called Aja and Decklink, neither company could tell me if it's possible with any of their products.
Another alternative would be to use a second video card and convert DVI to HDMI (I have two 30" monitors so am already using the two DVI outputs on the main video card), I want to output to a 47" TV monitor for client presentations. In the old days, it was always recommended not to use a second video card with music DAWs because of slowing down the PCI buss - is this still the case with the latest Mac Pro's?

The other thing we've done in the studio when working on films is to use two separate machines. One machine is running ProTools HD and it's the on that plays the video. Use MTC to lock the machines together, you hit play in Logic and hey presto, the ProTools locks to it and plays your video. No reason why you couldn't do this with two machines running Logic. The advantage with using ProTools (HD) is that you can have all of your reels in the one session, one after the other. Then (if your Logic work is properly organized and all of your cues have start points at the correct TC, then you don't even need to change ProTools sessions even once. You can switch between Logic projects (for each music cue) and the ProTools session will happily jump to the right part of the video at all times. This way you eliminate the question of trying to get the one machine to handle everything. Yes it's more of the old-school sync'd up video deck concept, but once you set it up, it's much faster and it works great. You can even route all of your physical outputs from Logic directly into the ProTools inputs and do one-pass (or almost one-pass) striping of all your Logic work to prepare your ProTools sessions for the orchestral sessions. We've done this for a couple of films and it was a very effective way of working.

Filtering OSPF routes from MPBGP to BGP speaker in the same VRF

I'm wondering if anyone has some ideas they an share on this.
Assume the following:
- CE1 is speaking *iBGP and OSPF to PE1 inside vrf foo
- PE1 is mutually redistributing CE1's OSPF table with MPBGP
- PE1 exchanges MPBGP routes with PE2.
- PE2 is mutually redistributing CE2's OSPF table with MPBGP
- CE2 is speaking *iBGP and OSPF to PE2 inside vrf foo
So the problem is that the OSPF routes redistributed into MPBGP from via one CE are being announced to the other CE via the PE-CE BGP process. Because those routes are already being received by the CE via the PE-CE OSPF process, they are showing up in the CE's BGP table as RIB failures.
Is there any way to filter those out? I've tried setting and matching tags and communities from within various redistribution points on the PE, but I can't seem to keep them out of the CE's BGP table.

are you sure you are using iBGP on both sides and not eBGP?
I'm asking because routes learnt by PE1 from CE via iBGP ( meaning same BGP AS number on CE1 and PE1 vrf foo) will not be propagated to CE2, because an iBGP route learned by a BGP speaker in not pushed to another iBGP speaker.
So it means that a show ip bgp neighbor vrf foo advertised routes on PE2 shall show that no routes from CE1 are being advertised to CE2.
As mentionned earlier, changing BGP admin distance is an option. Let BGP have a better distance on your CEs and this should do the trick :
router bgp xxx
distance bgp 20 20 20
Then after clearing bgp session, the rib failures are gone as OSPF is AD 110 and BGP is now AD 20 ( also remember that BGP does not annouces rib failure routes to other BGP peers)
cheers

Technical Routing Vs Logical Routing

Hi Friends,
Plz differentiale Technical Routing and Logical Routing

Routing
defines how the messages flow via XI (where to, via what) receiver and interface determinations in directory
Logical routing involves the definition of business services/systems for your interface.i.e we difine the flow of messages in a system landscape
Technical routing involves the definition of the communication channels, adapters, etc.
From a general point of view, whenever you talk about logical routing as such, it deals with the security and authentication aspect. By mentioning the business sytems/services for the interface, you are clearly telling, which client and logical system name XI should talk to, to either send or receive data..
.and technical routing involves exactly how the data will be sent or received.
Routing is one of the steps of the pipeline process.
Message was edited by:
Raghavesh Reddy

Latency Between Outputs After Project Conversion From Logic Pro 9

hiya!
i am experiencing a bizarre kind of latency – between outputs. for example, audio assigned to stereo outs 13-14 will leave my system 120 or so ticks after audio assigned to mono outputs 3 or 4. sometimes mono outputs are out of sync with one another too. there's no apparent rhyme or reason, and the latency itself seems to shift – even with plugins turned off and removed from the channel strips. if i have an aux that's outputting to channels 7-8 and do a send to an aux that outs to 13-14, this audio should be perfectly aligned, but it just isn't.
i experience this problem in sessions converted from logic 9 to logic x, though sometimes it seems to happen within sessions started in logic x. i can't for the life of me figure out why it's happening, but do believe there's some sort of error being introduced in the conversion. i can't find anything anywhere on the internet about it.
one temp fix i found was to insert an I/O plugin into the problematic aux, turn it on with an out assigned, then turn it off. sometimes that's worked, and sometimes it hasn't. i've been able to use delay compensation on certain tracks, but it's not an exact science, and sometimes the compensations themselves need to change in order for the tracks to sound aligned. it's beyond aggravating. in some situations, i've had to re-record entire sessions. not tight!
to be clear, this is not about monitoring latency, or having to slide tracks into alignment after recording, or the waveforms on the screen not matching up with what i'm hearing. this is not about plug-in latency. the situation i'm describing happens when plugins are entirely removed: audio that is supposed to be leaving logic at the same exact time via different outputs is somehow not aligned.
my signal chain:
logic pro x.0.7
mac pro quad core (trash can) into -->
apogee symphony 16x16 -->
neve 5059 16x2x2 -->
api 2500 -->
back into the symphony
i've been assured by both apogee and neve and sweetwater that this is not their issue--it's logic pro x. i'm inclined to agree, since it seems to be happening before the audio leaves logic.
please help! many thanks for anything!

godmodeinternet wrote:
thanks for your reply!
to answer some of your answers:
-i have all my channels go through auxes, in all projects, but i did attempt to route audio straight off the channels and encountered the same situation i described above.
-plug-in latency is likely set to ALL at all times, since i often track while in the 'mixing stage'. this is how i've always done everything.
ugh. the worst!
do you think there's anything in environment i might be able to swap around that might have gotten screwed up in the conversion?
thanks again.
I don't think it's an Environment issue, however, quite a few people have reported some corruption when importing Logic 9 projects, it usually takes the form of random Inspector Settings for Delay/Velocity and Preferences/Audio - Recording Delay being set to something other than 0 <zero>. This doesn't sound like your problem. Also sounds like your Plugin Latency setting (ALL) isn't the problem.. although if you're recording while mixing it should be set to Audio & Software instruments.
Have you used your hardware system successfully on an earlier version of OSX and Logic 9? If so then the answer is apparent, especially so if you notice it on projects started in Logic-X (current system) although it my take a certain level of project complexity before it shows up.

How to record video or use screen capture WHILE capturing audio from Logic??

Hi,
I want to record my self playing guitar and singing using my mac book pro built in camera. I want the audio to come from Logic so I can add whatever effects I want to the vocals. When I say audio from Logic I don't mean recording in Logic and adding it in post. I want it to be on the fly.
What I used to do was use the screen capturing program Snapz Pro. I would screen capture a box around photobooth for the video, and then record while having Logic's audio in the background. It screen captures my entire computers audio. So for example if I get an aim message the bleep would show up in the recording. Or if I raise the volume or lower it the little click sound fx would be in it as well.
Capturing the audio this way let me get Logic's audio effects in my video on the fly. It worked out great....until now! :/
I just got the audio interface "Duet 2". And am using a microphone instead of my mbp's built in one. When ever I tried to record and capture my systems audio - my entire computer would crash. Snapz Pro won't work with the system audio with the interface. It works fine without it though.
I then tried to use Quicktime's new movie recording feature. I see it only gives an option for microphone and now system audio. So I got soundflower to re route the audio but that doesn't help either. This is because when you capture this way you can't hear anything while your capturing. So if I were to record a video and wanted Logics audio in it, I would have to set the output to Soundflower first. So when I record I cant hear myself which defeats the purpose.
So my final question is, how can I record video while having Logic's audio? I don't need to record with the mic, because in Logic the mic audio is going thru the system audio with everything else.
I would like to use a process more similiar to Quicktimes straight movie recording instead of doing an odd way like I used to screen capturing a box around the photobooth screen.
Thanks

use Yawcam from Yawcam.com

Sending audio from logic to external hardware effects, and back into Logic

Hi,
I am currently trying to send audio from Logic to external hardware effects and then record this back into Logic.
My audio interface is a Edirol UA-25 which has only two outputs '1 and 2'.
I understand that I could create an 'aggregate device' which would create two more ins + outs being '3 & 4'.
I also understand that would need to use the Logic I/O plug in configuring this routing.
When treating the audio via the external hardware I particularly only want to hear the audio being processed and not the original 'uneffected' signal.
Can someone please explain if I am able to do all of this with just the UA-25, and if so, then how.
Cheers,
Mr Rock

You connect output 1 of your interface to your active speaker.
You connect output 2 of your interface to the input of your external effect.
You connect the output of your external effect to input 2 of your interface.
You route your track in Logic to output 2.
You create a new track.
You route this new track to output 1 and output 1 only.
You choose input 2 as the source for this track.
You arm the track.
You hit Record.
You hit Stop some time later.
Christian

When running a "stand-alone" APP..how do I send midi from Logic?

Hi all,
When running a "stand-alone" APP..how do I send midi from Logic?.....Please no IAC stuff it doesn't work.......thanx
SvK

using IAC here no problems. works very well.
you can host your au's in another app such as soundflower or au lab, but you are still going to need to get it to hear midi. you can use physical midi ports with something like a MTP midi interface, and getting the midi by routing the out of one port to the in of another (midi loop) but you have to be careful logic doesn't listen to the same midi signal or everything will jam up (midi feedback).

Extend routes from shipping point abc to xyz

Hi All,
i want to extend 5 routes from shipping point:abc to ftw
kindly help, Thanks

Hi,
You cannot define 5 routes for the same combination of departure zone and destination zone (including countries). For the same combination of departure country (plant country), departure zone, destination zone(from ship to party) destination country, even if you maintain different routes, there will be a problem in route determination in the sales order.
If there is a valid reason for doing this, you can mention the business logic. Then somebody can propose you a better solution.

Deleting the data from logical file/unix file

Hi all.
I need to delete the all the data from logical file (application server file/unix file).But I dont want to delete the logical file ( only data in the logical file should be deleted, i.e making file empty)
Thanks in advance.
Cheers.
sami

Hi Sami,
Refer thsi document https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/4d7aeb7d-0c01-0010-fa8a-a4a8e8968a93.
Regards,
Flavya

Acquired DVR, STB. and Router from Apartment cleanout; Return?

I am trying to do the right thing but poor customer service is not allowing me. I do IT work and received a DVR, STB, and Router from an apartment cleanout from a property owner. I am uncertain if the boxes are paid off or what, but rather than accept stolen property or flip them, I want to contact Verizon and have a return put out on the equipment. Hey maybe I'll get a credit or a few months of movies or something. But I certainly am not spending another minute sitting on hold to do this. I could not get through over 45 minutes yesterday. If I call and specify that I want to buy new service though, I get right through- only to be redirected anyways. Funny how it works. I love my FIOS service, always have, but to call them for anything requires taking a half day off of work. So, with that said- does anyone have contact info for equipment returns? Pittsburgh/Monroeville PA area. Again, if it's going to cost me anything, screw them. I will throw the stuff away as it should have been in the first place. If the equipment was paid for, it would be nice to have it activated to my account and no longer pay rental fees for my STB and DVR.
Message Edited by betteroff on 08-14-2009 06:47 AM

Don't know who to contact, but the video equipment is never considered paid off and remains forever Verizon property (that's how they make money on them). After a year I belive Verizon doesn't require the return of the router. They will not activate any STB without it being in their inventory and charging you a monthly fee.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

I am upgrading wi-fi router from Airport Express to Airport Extreme. I followed set up instructions yet I am still getting the flashing amber light and cannot setup (using manual setup or the continue button). What should I do??

Hello,
I am upgrading my wireless router from an Airport Express to an Airport Extreme. After disconnecting the Express and plugging the Extreme via ethernet cable to the modem, I am receiving a flashing amber light after connecting the power source. I also reset the modem while the Extreme was still powered and plugged into the modem, but no luck. I also tried resetting the modem and the Extreme and still no resolution. Please advise. Thank you!

This error usually occurs when the Windows Firewall and/or anti-virus software blocks the connection attempt from the PC to the AirPort Extreme.
Microsoft Security Essentials can do the same thing.
Things would be much easier if you had a Mac or iPhone or iPad to set up the AirPort Extreme. Otherwise try turning off the Windows Firewall and Anti-Virus programs, etc on the PC.
Restart the PC, then see if the PC can contact the AiPort Extreme. It will likely help to connect an Ethernet cable from the PC to one of the LAN <-> ports on the AirPort Extreme. You can disconnect the Ethernet cable once the AirPort Extreme has been configured.
Re-enable the Windows Firewall, Anti-Virus, etc and restart the PC.

How do I send my BMP info from logic to pedals and keys?

How do I send my BMP info from logic to pedals and keys?
Is it possible to sync my logic bmp with my microkorg so that my korg automatic will sync with the BMP from logic?

I'm not faniliar with the Micro, but logic outputs mtc and midi clock. The serttings are under project settings/synchronization. You'll have to set the Micro to external sync and be sending midi info from your computer to the Micro. Then if you hit play or record in Logic, the micro will chase it.

Routing from logic to spectral foo

Similar Messages

Maybe you are looking for