Routing Issue Cisco 2921
Hi Everyone.... I need urgent help on the below scenario....
ISP Managed Router connected to ADSL & looked for me to view or change configuration.... i have successfully configured my own 2921 to work with ISP router with IP NAT, Internet is working for all my LAN Users.
After connecting the VPN from outside to managed services router... i am able to reach my 2921 (10.10.10,100) but unable to access Internal LAN interface which is (10.10.100.1) on-wards....
ISP Managed Router (10.10.10.1) >>>>>>>>>> (10.10.10.100) MY Router (2921) (10.10.100.1)>>>>>>>>>>DHCP Users (10.10.100.21 to 100)
CONFIGURATION OF 2921 Attached.
Please give suggestions and advise if i need to so some more settings on 2921.
Hi Paul,
I have changed the config as required.... yes ISP router side is 10.10.10.1
Still issues.... Internet is working fine for my LAN users...
When i connect VPN on ISP managed router - 78.93.181.41 its connected....
I can ping 10.10.10.0 range.... and able to reach my router which is 10.10.100.1.... but unable to access anything on 10.10.100.0 (which is my LAN)
Any ideas.... as i asked ISP to allow this in their router which they did....
access-list 10 permit 10.10.100.0 0.0.0.255
this what i get from 2921 now....
RGTSTHALIA2900#show ip nat translations
Pro Inside global Inside local Outside local Outside global
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.1.111:161 192.168.1.111:161
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.100.11:161 192.168.100.11:161
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.100.111:161 192.168.100.111:161
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.100.112:161 192.168.100.112:161
tcp 10.10.10.100:1674 10.10.100.21:1674 2.21.39.117:80 2.21.39.117:80
tcp 10.10.10.100:1734 10.10.100.21:1734 2.21.39.117:80 2.21.39.117:80
tcp 10.10.10.100:1735 10.10.100.21:1735 2.21.39.117:80 2.21.39.117:80
RGTSTHALIA2900#show ip route
Gateway of last resort is 10.10.10.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 10.10.10.1, GigabitEthernet0/0
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
C 10.10.10.0/24 is directly connected, GigabitEthernet0/0
L 10.10.10.100/32 is directly connected, GigabitEthernet0/0
C 10.10.100.0/24 is directly connected, GigabitEthernet0/1
L 10.10.100.1/32 is directly connected, GigabitEthernet0/1
Similar Messages
-
Cisco IOS IPS in Cisco 2921/k9 router
Hi All,
I have a router of Cisco 2921 series (C2921/K9) basic box with IP BAse IOS image (SL-29-IPB-K9 IOS). I would like to enable IOS Level IPS feature on this Router now. Based on the Cisco Document i have found i need to purchase an additonal subscripton license to enale the IPS feature. My querry is-
Will it support on the Basic IP Base IOS or do i need to change the IOS?
If i need to purchase the Subscription Licesne, how can i get the part number and cost for the same?
Do i need to buy any addtional module for this like (NME-IPS-K9) ?
Thanks in advance for your quick support
regards
SunnyHi Sunny
1. Yes you can enable IPS on IOS with the security license, without buying a subscription, but this would make little sense - new signatures are being released all the time so you would not be protected from recently discovered vulnerabilities/attacks.
2. Correct, the modules and appliances run a different kind of software and are much more powerful
3. If you add the module, you do NOT need the security license. It would still be advised to get a subscription license to get signature updates for the module.
I hope this helps, let us know.
regards
Herbert
jacob.samuel wrote:Dear Herbert,Thanks alot for the wonderful post. It clear most of my doubts. Still i kindly need to know few more points-1) Cant we enable IPS Feature on 2921/K9 router (with Sec license or 2921Sec/K9 bundle) without signature subscription license (is it a must? it is for getting updates of signatures and for support only, right?)2) I came to know from a distributor pre-sales engineer that the Cisco IOS Level Intrusion Protection is not going to provide the full feature of IPS like NME module or IPS Applinace. Is that right?3) If i add NME-IPS-K9 Module to my 2921 Router, without enabling Sec License, can i enable IPS feature on the Router. Or is it a must that i need to buy Sec License (SL-29-SEC-K9)?Attaching the Datasheet of NME-IPS-K9 module (Page num 5 above Table 3) mentione as follows-Cisco IOS Software Feature Sets and ReleaseTable 3 lists the required Cisco IOS feature sets and releases for Cisco IPS AIM and IPS NME on the Cisco 1841,
2800 and 3800 series Integrated Services Routers Note that, IPS NME on the Cisco 2900 and 3900 Integrated
Services Routers does not require a Security Feature license.
In that case if i buy a module i can install it on the 2921K9 box directly and can enable the IPS feature right? I dont need any License and additonal signature subscription here to enable the IPS feature (if i dont need signature updates and support) right?
thanks alot for the support.
regards
Sunny -
Will a 2 port LAG setup between 2 cisco 200-50s create routing issues?
I followed this guide. http://sbkb.cisco.com/CiscoSB/GetArticle.aspx?docid=caae365b755f46f5989177cb68216304_Link_Aggregation_on_Cisco_Series_Managed_Switches.xml&pid=2&converted=0 and linked ports 2 and 26 on both switches. Outside IT staff seems to think this will cause routing issues if multiple vlans are not involved.
Hello,
VLANs are not required for LAGs to function properly. Once you configure the LAG members you can configure the LAG as a trunk port with multiple VLANs, and access port with just one, or even a routed port with an IP address on it.
As long as both sides of the LAG are configured the same way there won't be an issue. Since these switches are Layer 2 only, they don't even do any kind of routing, so your outside IT may have meant a layer 2 loop, which will happen with multiple connections between the same switches. But when you configure them as a LAG is treats those links as the same connection, so there is no layer 2 loop either.
Hope that helps,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts* -
Configuring - Cisco 2921 with Switch Module/POE PS and 3750-x 24 port switch
This is what I have
- Cisco 2921 router
with SM-ES2-24-P switch module and
POE power supply
-Cisco 3750x- 24 port Switch
I have port G1/0 (which connects to 24p Switch Module port g0/26 logically) configured with 3 sub interfaces (management, User and VOIP)
I want to connect 3750x to G0/1 on 2921 via fiber GBIC but want to use same three VLANs
I can not daisy chain 3750x via the switch module because it does not have fiber port.
I do not want to create another routed (g0/1) interface because I want to keep Users on both switches on the same subnet without further splitting the subnet in two.
I hope I am not making this confusing.
How can I bridge g1/0 and g0/1 so I can pass vlan traffic between two switches?
Second problem i have is ...
I have a VOIP connected to switch module (SM) and it is not getting any power.
I went in to all the interfaces on SM and issued power inline auto command
On the SM (sh power inline) - available is 0.0(w)
on the 2921 (sh power inline)
- power supply status is good,
- maximun power available is 280.
- interface G1/0( which connects to SM)
*device is unknown
* powered off
* allocated 0.0 watts.
I already tried resetting SM
Is there any other command I need to issue?
thanks for your help.I'm having a similar issue. I can get trunked connectivity between the switch module and the router if I put the IP address on the router sub interface, but not if I put it on a VLAN interface. I was hoping to have it on a VLAN sub interface on the router so I could use Gig0/1 and Gig0/2 to connect other switches and have them on the same VLANs. I'm using Gig1/0 on the router side and Gig0/51 on the switch side (48-port module).
Any help? Am I on the wrong track altogether? -
Problem whit cisco 2921 + EVM-HD-8FXS/DID whit CUCM
Hello everyone.
I have the following problem that I am not able to resolve. I define a new connection BRI.
I can make calls seamlessly between the Cisco Unified Communications Manager (version: 8.5.1.10000-26) and Cisco 2921 (CISCO2921-V/K9).
But when you receive calls from BRI Cisco receives the call but the Cisco Unified Communications Manager does not tranfere for Ext
And I can not understand why. In other BRI interfaces do not have this problem.
This configuration here that I'm using.
Current configuration : 17238 bytes
! Last configuration change at 18:02:34 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname <<omitted>>
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 <<omitted>>
aaa new-model
aaa authentication login default none
aaa authentication login <<omitted>>
aaa accounting connection h323 start-stop group radius
aaa session-id common
clock timezone PORT 0 0
clock summer-time PORT recurring last Sun Mar 1:00 last Sun Oct 1:00
network-clock-participate slot 1
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-participate wic 2
network-clock-participate wic 3
network-clock-select 1 BRI0/0/0
network-clock-select 2 BRI0/1/0
network-clock-select 3 BRI0/2/0
network-clock-select 4 BRI0/3/0
no ipv6 cef
ip source-route
ip cef
no ip domain lookup
ip domain name <<omitted>>
multilink bundle-name authenticated
isdn switch-type basic-net3
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed- <<omitted>>
enrollment selfsigned
subject-name cn= <<omitted>>
revocation-check none
rsakeypair TP-self-signed- <<omitted>>
crypto pki certificate chain <<omitted>>
<<omitted>>
quit
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call carrier capacity active
voice rtp send-recv
voice service voip
no ip address trusted authenticate
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
h323
modem passthrough nse codec g711ulaw
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class h323 1
h225 timeout tcp establish 5
voice translation-rule 1
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 2
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
rule 4 /^21 <<omitted>>/ /21 <<omitted>>/
rule 5 /^21 <<omitted>>/ /21 <<omitted>>/
rule 6 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 3
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 4
rule 1 /^0/ /400/
rule 2 /^/ /21 <<omitted>>/
voice translation-rule 5
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 11
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 12
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /.*/ /21 <<omitted>>/
voice translation-rule 13
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 14
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 15
rule 1 /.*/ /21<<omitted>>/
voice translation-rule 21
rule 1 /^./ /0&/
voice translation-rule 22
rule 1 /^./ /0&/
voice translation-rule 25
rule 1 /^./ /0&/
|
voice translation-rule 23
rule 1 /^./ /0&/
voice translation-rule 24
rule 1 /^./ /0&/
voice translation-rule 32
rule 1 /^212104974/ /21 <<omitted>>/
rule 2 /.*/ /212104975/
voice translation-profile INLINE_EMPA
translate calling 22
translate called 2
voice translation-profile INLINE_EMPB
translate calling 23
translate called 3
voice translation-profile INLINE_EMPC
translate calling 25
translate called 5
voice translation-profile INLINE_EMPE
translate calling 24
translate called 4
voice translation-profile INLINE_EMPD
translate calling 21
translate called 1
voice translation-profile OUTLINE_EMPA
translate calling 12
voice translation-profile OUTLINE_EMPA_NT_FAX
translate calling 32
voice translation-profile OUTLINE_EMPB
translate calling 13
voice translation-profile OUTLINE_EMPC
translate calling 15
voice translation-profile OUTLINE_EMPE
translate calling 14
voice translation-profile OUTLINE_EMPD
translate calling 11
license udi pid CISCO2921/K9 sn <<omitted>>
hw-module pvdm 0/0
hw-module sm 1
username admin privilege 15 password 0 <<omitted>>
redundancy
ip ssh time-out 60
ip ssh authentication-retries 2
class-map match-all Voz
match access-group 100
policy-map QoS
class Voz
priority 200
set precedence 5
class class-default
fair-queue
gw-accounting aaa
attribute acct-session-id overloaded
acct-template callhistory-detail
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address <<omitted>> 255.255.0.0
ip access-group BLOCK in
load-interval 30
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr <<omitted>>
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
interface BRI0/0/0
description EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/0/1
description Ecotel EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/0
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/0
description EMPB N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/1
description Ecotel EMPB N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/3/0
description EMPE N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/3/1
description Ecotel EMPA N
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/0
description B EMPC N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI1/1
description Ecotel EMPE N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/2
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/3
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/4
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/5
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/6
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/7
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip rtcp report interval 500
ip access-list extended BLOCK
deny ip any host <<omitted>>
deny ip any host <<omitted>>
deny ip any host <<omitted>>
deny ip any host <<omitted>>
permit ip any any
ip radius source-interface GigabitEthernet0/0
radius-server host <<omitted>> auth-port 1647
radius-server host <<omitted>> acct-port 1647
radius-server key <<omitted>>
radius-server vsa send accounting
control-plane
voice-port 0/0/0
translation-profile incoming INLINE_EMPD
translation-profile outgoing OUTLINE_EMPD
compand-type a-law
cptone PT
voice-port 0/0/1
compand-type a-law
cptone PT
voice-port 0/1/0
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
voice-port 0/1/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA_NT_FAX
compand-type a-law
cptone PT
voice-port 0/2/0
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
voice-port 0/2/1
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 0/3/0
translation-profile incoming INLINE_EMPE
translation-profile outgoing OUTLINE_EMPE
compand-type a-law
cptone PT
voice-port 0/3/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 1/0/0
compand-type a-law
cptone PT
voice-port 1/0/1
compand-type a-law
cptone PT
voice-port 1/0/2
compand-type a-law
cptone PT
voice-port 1/0/3
compand-type a-law
cptone PT
voice-port 1/0/4
compand-type a-law
cptone PT
voice-port 1/0/5
compand-type a-law
cptone PT
voice-port 1/0/6
compand-type a-law
cptone PT
voice-port 1/0/7
compand-type a-law
cptone PT
voice-port 1/0/8
translation-profile incoming INLINE_EMPC
translation-profile outgoing OUTLINE_EMPC
compand-type a-law
cptone PT
voice-port 1/0/9
compand-type a-law
cptone PT
voice-port 1/0/10
compand-type a-law
cptone PT
voice-port 1/0/11
compand-type a-law
cptone PT
voice-port 1/0/16
compand-type a-law
cptone PT
voice-port 1/0/17
compand-type a-law
cptone PT
voice-port 1/0/18
compand-type a-law
cptone PT
voice-port 1/0/19
compand-type a-law
cptone PT
ccm-manager music-on-hold
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp profile default
dial-peer voice 1 pots
description +++++ Dial-peer +++++
incoming called-number .
direct-inward-dial
port 0/0/0
dial-peer voice 10 pots
description touchwise
destination-pattern 1T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 20 pots
description globalmove
preference 1
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 30 pots
description globaltemp
shutdown
destination-pattern 3T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 40 pots
description EMPE
destination-pattern 4T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/3/0
dial-peer voice 100 voip
preference 1
destination-pattern .
session target ipv4:10.35.2.1
voice-class codec 1
no vad
dial-peer voice 21 pots
description globalmove
preference 2
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 101 voip
preference 2
destination-pattern .
session target ipv4:10.35.2.2
voice-class codec 1
no vad
dial-peer voice 24 pots
description globalmove
preference 1
destination-pattern 59[1236].......
port 0/3/1
forward-digits 9
dial-peer voice 25 pots
description globalmove
preference 1
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 26 pots
description globalmove
preference 2
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 27 pots
description globalmove
preference 1
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 28 pots
description globalmove
preference 2
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 34 pots
description globalTemp
preference 1
destination-pattern 39[1236].......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/1
forward-digits 9
dial-peer voice 35 pots
description globalTemp
preference 1
destination-pattern 300T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 37 pots
description globalTemp
preference 1
destination-pattern 3[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 14 pots
description empd
preference 1
destination-pattern 19386648.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 15 pots
description empd
preference 1
destination-pattern 19365483.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 16 pots
description empd
preference 1
destination-pattern 19341347.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 50 pots
description EMPC
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 1/0/8
gateway
timer receive-rtp 1200
gatekeeper
shutdown
call-manager-fallback
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.35.2.250 port 2000
max-ephones 100
max-dn 300
transfer-pattern 09........
transfer-pattern 02........
transfer-pattern 0.........
transfer-pattern 000T
transfer-pattern 4...
keepalive 10
time-format 24
date-format dd-mm-yy
shutdown
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login authentication touchwise
transport input ssh
line vty 5 15
login authentication touchwise
transport input ssh
scheduler allocate 20000 1000
ntp master 5
endIf t i "Translation Pattern Configuration" switch to another "Partition" existing or internal it works.
If change back for the new i create. It does not work.
So I must be some flaw i made in Cisco Unified CM. -
Hi @all,
wir würden gerne einen Cisco 2921 mittels PPPOE über einen FTTH-Link an einem Internet-Business Light Anschluss der Swisscom in Betrieb nehmen. Als Bridge ist das Zyxel FSG1100HN im Einsatz.
Die Bridge mit einem PC und PPPOE-Verbindung funktioniert einwandfrei.
Der Cisco-Router sendet zwar Datenpakete um die Authetifizierung zu starten, bekommt aber keine Rückmeldung (PADI timer expired).
Hat jemand von Euch einen TIP?
Besten Dank im Voraus
OlafHi Olaf,
This is the Optical Section I think your post would be better in the Switching Section.
Chris -
Routing Issue with 2 Nics on Windows Server 2008 R2
Good Day
My issue is I needed to set up port forwarding for a web server to communicate with our hotels management server to check availability.
Initially the server has a single Nic configured in the 172.26.1.0 /24 network , Its default gateway the Switch vlan interface 172.26.1.1
We have many vlans for all the systems in the hotel and the server also needs to communicate with 3 other servers on different subnets which it does just fine.
I now added an additional adsl line with a managed router which has an interface of 192.168.10.1 /24 , My servers second NIC has the IP address 192.168.10.2 with its gateway being the 192.168.10.1
This 192.168.10.0 network is in a L2 Vlan and the rest of the network does not know it exists. It was working fine then just stopped asfter i added a static route to the server , which i did with RRas... I did this as the server could not communicate with
just one of the servers..
If i disable the 172.26.1.0 NIC the port forwarding works but then obviously the rest of the network goes down.. I know its a routing issue but am lost
please helpHello,
using multiple default gateways is not a good idea.
See details in http://support.microsoft.com/kb/159168/en-us
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter: -
Routing issue- seeing same IPs for two hops
Hello All,
I'm seeing two same IPs in the traceroute output. Is that due to routing issue that nexhop is as the same device for the first time?
Log:
6 10.30.102.26 61.060 ms 10.30.100.142 61.266 ms 10.30.102.26 61.071 ms
7 10.30.102.26 61.139 ms 61.211 ms 10.61.191.2 60.948 ms
Can you guys help me to fix the issue??
Regards,
ThiyaguAre you load balancing anywhere?
6 10.30.102.26 61.060 ms
10.30.100.142 61.266 ms
10.30.102.26 61.071 ms
7 10.30.102.26 61.139 ms 61.211 ms
10.61.191.2 60.948 ms
HTH,
John
*** Please rate all useful posts *** -
I think verizon has a routing issue with Telia.
thought I would share this, Telia has admited an issue on their network
Twitter / Telia_service: @Ungvall routing problem? This ...
https://twitter.com/Telia_service/status/179661595276881921
Cached
Similar
Share
View shared post
BTW Apparently @Telia_service had routing problems on both the latest iOS and ... DNS problem and we are working with Akamai for a sollution to this problem -
I am having a routing issue with a 3550 switch. I have 5 vlans and I need one of the vlans to access a different router based on destination IP rather than our edge router. I have entered a static route on the 3550 that points to the secondary router whenever a certain network is tried to be accessed. My problem is I can't seem to get the traffic to flow correctly. When I trace route an address on the Internet the path shows as expected, the 3550 then my firewall then my edge router. When I trace an address that is on the other side of the secondary router I get the 3550 as the first hop, then nothing. I can ping the address so I know the path is up. What could be the issue? Thanks in advance.
Hello,
in addition to Mahmood´s post, what do you have defined as the next hop for the default route to the secondary router ? If you use an interface on the 3550 as the next hop, make sure that whatever is connected is in the same subnet, otherwise use the IP address of the next hop. So, let´s say your remote network is 192.168.1.0, and the secondary router is connected to FastEthernet0/1, your default route should look like this if the secondary router is in the same subnet (in this example, the IP address of the secondary router would be 172.16.1.2):
interface FastEthernet0/1
no switchport
ip address 172.16.1.1 255.255.255.252
ip route 192.168.1.0 0.0.0.255 FastEthernet0/0
Otherwise, try:
ip route 192.168.1.0 0.0.0.255 172.16.1.2
where 172.16.1.2 would be the address of the secondary router.
Does that make sense ?
Regards,
GNT -
No airtunes with pppoE due to routing issues?
I just switched to an optical fiber to the home internet connection (which is getting pretty popular here in Japan). Needless to say, the network is very fast, however, I can no longer use airtunes via my airport express network. The airport express stations (both of them) no longer show up in iTunes. My guess is that this is due to a routing issue and the same problem must have been encountered by others before and hopefully solved. The new internet connection uses pppoE to make a connection to the internet service provider. This gives me an internet address of the form 125.197.xx.yy. I still have my airport express set to get an address via dhcp (which the new optical fiber hub provides) and is of the typical private network form 192.168.1.4. When I am connected by pppoE to the internet, my iTunes cannot see my airport express due to routing issues I assume. Is there an elegant solution to this -- can I use my airtunes and the internet at the same time? Would modifying the internet routing help here (I have used this before when I have had multiple interfaces going (e.g. one in a secure local lan and the other supporting an internet connection via ssh to the outside world). Any advise would be much appreciated. I haven't tried asking my airport express to log in via pppoE -- is this the only solution?
Well as I have for my last several posts -- I solved the problem myself. I am pretty sure that the root cause was a routing problem (pretty obvious in fact). By have the airport express base station connect via pppoE itself (I have a remote relay airport express as well) and switching to NAT and DHCP distribution of addresses via the airport express, I can both see my airtunes as well as my ethernet connection. It is a non-ideal solution as I have a fixed IP which would have been convenient to log in from outside to, but I guess I can live with that.
-
Audio tracks playing different audio tracks - routing issue?
I'm having trouble with some routing issues I believe. Here's the deal:
Some audio tracks are playing different audio tracks, when that region is not even in it. For instance:
Track #2 is Soloed. Output is Output 1-2. I hear the audio file that is in Track #1, which is NOT Soloed and I shouldn't even hear. I don't hear anything from Track #2. The only way I can hear Track #2 is by playing it from the audio bin, which obviously isn't going to work out right.
If I drag the audio region of Track #2 to a brand new audio track, I still don't hear anything. Is it possible this audio file(s) got corrupted somehow?
Please help!Chris Joye wrote:
I'm having trouble with some routing issues I believe. Here's the deal:
Some audio tracks are playing different audio tracks, when that region is not even in it. For instance:
Track #2 is Soloed. Output is Output 1-2. I hear the audio file that is in Track #1, which is NOT Soloed and I shouldn't even hear. I don't hear anything from Track #2. The only way I can hear Track #2 is by playing it from the audio bin, which obviously isn't going to work out right.
If I drag the audio region of Track #2 to a brand new audio track, I still don't hear anything. Is it possible this audio file(s) got corrupted somehow?
Please help!
Check the parameters, in the left side of the arrange page window.
To me, it sounds as if you have a bunch of arrange tracks, which are all playing back through audio track #1.
Cheers -
I have a new Apple TV and am trying to set up airplay mirroring for my Ipad 2. I can stream music but not the images on the Ipad. The tech support says it is probably a router problem ( I have a Linksys WRT 400N router) but Cisco is not helping me. Anybody have any ideas how to get the two to work together? Thanks
What version is on the Apple TV? Go to settings - general - about. The latest firmware is 4.4.2
Also see if this helps
http://support.apple.com/kb/TS4085 -
IB Routing issue. Unable to find routing to the corresponding incoming msg
Hi All,
We are facing a Routing issue. The flow of message across the DB is given below.
1) Message will be triggered from 3rd party application to PeopleSoft portal with Service Operation A
2) From portal one more service operation B will be invoked to communicate with CRM
Both the service operations are synchronous. I have tested the Service operation in CRM and I am able to get the results. But in Portal if I test, I am getting the error like
+"Unable to find routing corresponding to the incoming request message"+
I have checked the routing alias name between Portal and CRM data bases and Its same.
could you please give us a clue to debug this further?
Thanks,
Hari.AYou should check which permission list the service operation is attached to, and check if the user has been granted to, Something like the following from the backend :
SELECT distinct c.roleuser
FROM psclassdefn a, psroleclass b, psroleuser c
WHERE a.classid = b.classid
AND b.rolename = c.rolename
AND a.classid = '<permission_list>' If nothing is returned for your user, then you could created a new role and give it to the user.
Also, since you are on Peopletools 8.52, all this configuration settings can be done through Integration Network WorkCenter. I wrote articles about that (and you can find something about permission list for a given service operation as well) :
http://gasparotto.blogspot.nl/2012/11/peopletools-852-integration-network.html
Nicolas. -
NO HELP WITH ROUTING ISSUES FROM VERIZON
Spend 2 hours with technical support to no avail. Have routing issues where I can’t get from my FIOS residential account to remote web site abroad. Trace route fails at so-0-0-0.XT1.AMS2.ALTER.NET [146.188.14.209]. FIOS technical support is incapable of doing any troubleshooting beyond basic customer premises equipment, refusing to escalate the case to network engineering team. I was basically told by FIOS tech support supervisor {edited for privacy} that this is not Verizon’s problem and no help will be provided. What is even more frustrating that Verizon agents are not capable of receiving emails from customers with details such as trace route.
Is there anyone at Verizon monitoring this and able to help? Just in case, ticket number that I have with Verizon is {edited for privacy}
Here is trace route details.
tracert 212.44.136.226
Tracing route to brserv.bridgetour.ru [212.44.136.226]
over a maximum of 30 hops:
1 1 ms <1 ms 1 ms Wireless_Broadband_Router.home [192.168.1.1]
2 12 ms 9 ms 9 ms L100.BSTNMA-VFTTP-71.verizon-gni.net [98.118.28
1]
3 16 ms 19 ms 19 ms G0-6-4-1.BSTNMA-LCR-21.verizon-gni.net [130.81.
75.132]
4 45 ms 15 ms 8 ms ae3-0.BOS-BB-RTR1.verizon-gni.net [130.81.151.6
5 19 ms 19 ms 19 ms 0.xe-3-2-0.IL1.NYC9.ALTER.NET [152.63.26.81]
6 21 ms 19 ms 19 ms 0.ge-1-2-0.IL1.NYC12.ALTER.NET [152.63.26.86]
7 107 ms 108 ms 107 ms so-0-0-0.XT1.AMS2.ALTER.NET [146.188.14.209]
8 * * * Request timed out.
9 * * * Request timed out.
10 * * * Request timed out.
11 * * * Request timed out.
12 * * * Request timed out.
13 * * * Request timed out.BT help aren't always that helpful, but BT engineers claim that it is a BT sales issue and nothing to do with them seems a bit extreme.
Are you sure your daily speed is 8Mbits, not 8Mbytes? How are you measuring this? Is it the number coming from the BT speedtest?
If it really is 8Mb, then I think it's worth checking with the mods; at: http://bt.custhelp.com/app/contact_email/c/4951 . But be aware they take 3 working days to reply: sometimes more if busy.
Maybe you are looking for
-
How do i delet music from my iTunes account?
How do I delete music from my iTunes account?
-
I wonder if anyone can check this behavior in CS3. I noticed that simply applying the Magic Bullet Looks effect, without ever opening the Looks Builder and making any adjustments, that my blue skies turn gray. Viewing on a calibrated, external NTSC m
-
.avi files and Final Cut
When I try to import an .avi file Final Cut says .avi files are not optimal and I need to recapture the footage - but all I need is to import an already edited .avi file from my desktop to Final Cut, if it supports .avi files why can't I import them?
-
Remove a row from multiple tables
Hello, I have a form that has what appears to be one table. Since I needed 30 columns (29 of them are single character fields) I had to use 2 table objects. Then I needed the ability to add and remove rows. Adding a row at the end is easy enough.
-
SampleCode for MQnWLS -- Unresolved:'wlsmqXAQCF'
Hi, I try the Using MQSeries as a Transactional Resource Manager with Weblogic Server V. 1.0. When I excute the sample code: java MQClient t3://localhost:7001 "hihi" occurs some error-message. Have an