Routing non-contiguous WAN with RV042?

Environment: RV042 V03 (firmware v4.0.0.07-tm) currently routing a /29 to an internal network.
We used up our /29 and now have a 2nd non-contiguous /29.  Both of these come over the same wire.
Is there any way to configure the RV042 to route both blocks?  I need to do 1:1 NAT with all of the addresses in the first /29 as well as 3 addresses in the second /29.  There is only one internal subnet.
Any help would be appreciated.

Or to ask an alternatie question, is there a Cisco product that would allow me to do this routing?

Similar Messages

  • Can I route non-XML files with NW PI 7.0?

    Hello,
    I have NW 7.0 PI installed. I need to implement very simple scenario:
    1. There are two folders Source and Target
    2. Any file (non-XML, binary for example) comes to the Source folder
    3. File needs to be picked up and routed without any modifications to the Target folder
    Questions:
    1. Can I implement that with NW? I guess I can
    2. How do I do that? Is there any example or some description of implementing such a simple scenario (I have a few samples on how to implement complex scenarios that work with XML files, but I don't need that complexity)
    Thanks in advance.

    Hi,
    Check out the Sravya's blogs for starters, It has lot of links which will help you to learn various pieces of XI.
    Aspirant to learn SAP XI...You won the Jackpot if you read this!-Part I
    Aspirant to learn SAP XI...You won the Jackpot if you read this!-Part II
    Aspirant to learn SAP XI...You won the Jackpot if you read this!-Part III
    Thanks,
    Pooja

  • Enumerators with Non-Contiguous Values?

    I have seen enumerators in labview that have non contiguous values, but i cannot figure out how to create them myself. Usually they are associated with calls to external .net or .dll libraries.
    In this case the return values of a function I am calling are enumerated in hexedecimal, and are basically 1 value per bit. Is it possible to create such an enum? Of course I can handle the result as an int, but this is not as readable.
    Thanks in advance

    You can display it as a ring control... To the user, it would be transparent (and that is what you probably saw).  Otherwise you will have to bit twiddle to get contiguous values for the enum.
    Message Edited by Stradis on 07-09-2007 02:35 PM
    Paul <--Always Learning!!!
    sense and simplicity.
    Browse my sample VIs?

  • Help with RV042 Static Routing

    I just purchased an RV042 Dual WAN Router. Both WAN's are connected from different ISP's. I have a PBX phone server connected to this router and want all traffic to and from this phone server going out strictly on one WAN and all the computers and the rest of the traffic on the other WAN. If I understand correctly, this needs to be set up in static routes? If that's the case, how would I do that? If not, the question still stands. Please help.

    Hello Vitaly,
    What you are looking for is Protocol Binding. By setting this up you will be able to control what traffic goes out which WAN port. Protocol Binding can be done for certain traffic types or for certain IP addressess.

  • Why is wireless router connectivity is different with Powerbook than iMac?

    I had problems with my 10.2 on the G3 450 iMac (that caused me to go to 10.3 about 2 weeks ago), my trusty old Buffalo router fried its WAN port. I replaced it with a Netgear unit, then a Linksys unit, now I'm back to Buffalo. The ongoing problem is that the laptop has a heck of a time connecting to the internet - while the iMac (via ethernet) has no problems whatsoever. It doess/did this with every manufacturer of routers I tried (since first I thought it may be a Netgear incompatibility issue).
    Strange part about the problems: Only initially does it spend 20+ seconds (close to Safari/Firefox timeout) "looking for" the host. Once it has found it, if you click on any links within the same host, it's lightning-fast. Just the initial callup seems to be inordinately difficult. I was hoping new firmware for the wireless modem, 10.4, the latest Airport update etc would alleviate the situation - no such luck. It USED to work fine on the old wireless router ... Also, it does this "looking for" business whether I have security enabled or not (I usually run 128bit encoding).
    I don't really mind waiting for a few seconds for a site to load, but when you're talking about something like Yahoo or ESPN, all these independent advertising servers have to be contacted to load the page and - you guessed it - it's a 20+ second delay for each one...
    I've rebooted the router and the laptop many times; I doubt it's the cable modem as the Ethernet on the iMac comes from the same router an doesn't have a problem at all. Any chance it's a setting of some sort in the preferneces panels?
    The problem appeared initially with the Netgear router. The whole reason I went back to Buffalo is that I never had any issues in the 4 years I owned the previous one (until the WAN port went out). I also tried a Linksys router but admittedly didn't spend a lot of time with it as the delay problem appeared right from the start.
    As far as 3rd party hardware is concerned, I wouldn't mind just getting an Apple Airport station at this time, but really don't want to spend the $ if it's an issue with either the laptop or its Airport card. I guess I could get one here at the local Apple store and bring it back if it doesn't work any differently (at least then I'd know it's either a laptop or a Comcast Cable-issue...).
    System setup:
    Desktop: G3 "Graphite" iMac / slot-loading / 400Mhz / 640MB RAM / 10.3.9
    Laptop: 15" G4 Aluninium Powerbook / 1.25Ghz / 1GB RAM / 10.4.6
    Wireless: Buffalo AirStation Turbo G WHR-HP-G54 (wireless to laptop / ethernet to iMac).
    Powerbook 15/1.25GHz/1GBRAM   Mac OS X (10.4.6)  

    It sounds as though you're having a problem with DNS lookups. Try this, type into Terminal (Applications > Utilities)…
    sudo lookupd -flushcache
    It will subsequently ask you for your administrator password. Type it in and then wait for the prompt to return. Do not do anything before then. Now, restart and see if things are any better.

  • Is there a way to copy non-contiguous words from a PDF

    Is there a way to copy non-contiguous words from a PDF?  Is there a way to use a template or mask that will isolate certian areas to be copied with spaces in between the words so that when you go to paste the contents into multiiple fileds, the separate words will pop into the appropriate fileds.  The fields will be in a submission form.
    Please let me know if this is possible.
    Thanks
    Linda

    No it's not.

  • How do I AI config for SCXI multiple non-contiguous channels

    I need to configure a measurement of with multiple groups of thermocouple channels.
    Using LV 5.1.1 (could use 6, but I am supporting lots of code built with 5.1.1), DAQ 6.8.1 (can up to 6.9.1 if it matters), PXI-6052E, SCXI-1102, SCXI-1303 (or TC-2095).(using SCXI addressing).
    The problem occurs when I try to configure multiple scan lists with gaps between channels.
    (see LV DAQ SCXI example SCXI-1102/1127/1101 Thermocouple)
    example channel list:
    ob1 ! sc1 ! md1 ! cjtemp
    ob1 ! sc1 ! md1 ! 0:3
    ob1 ! sc1 ! md1 ! 5:9
    This gives an error: -10370 in AI Group Config.
    Likewise if I use an individual channel in each address string. like:
    ...md1 ! 0
    ...md1 ! 1
    ...md1 ! 3
    But, I can skip channels betwe
    en cjtemp and the first channel of the next scanlist without error.
    Also, I can add scan lists for other modules, like:
    ...md1 ! 0:3
    ...md1 ! 4:8
    ...md3 ! 12:14
    without error!
    What I really want to do is to do AI Config first for all channels, then start, then loop on AI Read and some processing & storage.
    When I loop through the channel address lists (strings with contiguous channel sets e.g. 3:6) I get the same task # for all config calls. Then when I loop through the AI Start's for each , I get an error -10609 in AI Clock Config.
    The thing is that I cannot necessarily have all contiguous channels, and I don't want to go through a sequence of {AIConfig, AIStart, AIRead, AI CLear} for each scanlist each time through. That takes too much time and resources.
    Eventually I want to configure multiple non-contiguous scanlists in multiple SCXI modules.
    But, for right now I need to do this for one SCXI module.
    Anyone have any ideas?
    How can I approach this.
    Thanks
    Dave

    Dave
    Check the following link into the NI Knowledgebase (if you haven't already)
    which I think explains your situation.
    http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/02a55e1f39
    e8bd15862567e700577877?OpenDocument
    Bottom line is you will not be able to skip channels on any SCXI module
    other than the SCXI-1112. You will need to include the channels in your scan
    list then discard the data later.
    Either that or as the Knowledgebase suggests, use Virtual Channels. You can
    then miss channels out in the scan list as you require. They actually get
    scanned but NI-DAQ discards the data for you.
    Ian Bell
    NI UK
    "Dave Karon" wrote in message
    news:[email protected]...
    > I need to configure a measurement of with multiple groups of
    > thermocouple channels.
    > Using LV 5.1.1 (could use 6, but I am supporting lots of code built
    > with 5.1.1), DAQ 6.8.1 (can up to 6.9.1 if it matters), PXI-6052E,
    > SCXI-1102, SCXI-1303 (or TC-2095).(using SCXI addressing).
    >
    > The problem occurs when I try to configure multiple scan lists with
    > gaps between channels.
    > (see LV DAQ SCXI example SCXI-1102/1127/1101 Thermocouple)
    > example channel list:
    > ob1 ! sc1 ! md1 ! cjtemp
    > ob1 ! sc1 ! md1 ! 0:3
    > ob1 ! sc1 ! md1 ! 5:9
    > This gives an error: -10370 in AI Group Config.
    > Likewise if I use an individual channel in each address string. like:
    > ..md1 ! 0
    > ..md1 ! 1
    > ..md1 ! 3
    >
    > But, I can skip channels between cjtemp and the first channel of the
    > next scanlist without error.
    > Also, I can add scan lists for other modules, like:
    > ..md1 ! 0:3
    > ..md1 ! 4:8
    > ..md3 ! 12:14
    > without error!
    >
    > What I really want to do is to do AI Config first for all channels,
    > then start, then loop on AI Read and some processing & storage.
    > When I loop through the channel address lists (strings with contiguous
    > channel sets e.g. 3:6) I get the same task # for all config calls.
    > Then when I loop through the AI Start's for each , I get an error
    > -10609 in AI Clock Config.
    >
    > The thing is that I cannot necessarily have all contiguous channels,
    > and I don't want to go through a sequence of {AIConfig, AIStart,
    > AIRead, AI CLear} for each scanlist each time through. That takes too
    > much time and resources.
    >
    > Eventually I want to configure multiple non-contiguous scanlists in
    > multiple SCXI modules.
    > But, for right now I need to do this for one SCXI module.
    >
    > Anyone have any ideas?
    > How can I approach this.
    > Thanks
    > Dave

  • IRR and non-contiguous range

    I am looking to calculate an IRR with cash flows that are not in a single column or row.  I am wondering if Numbers can handle a non-contiguous range and if so, how?
    After experimenting a bit, I expected IRR((a, b:c, d), ) to work but it didn't. Instead, I got an error message that states, "The formula contains a list where a single argument is expected."
    I would suspect that dealing with (or not being able to handle) non-contiguous ranges is not an IRR issue but any function looking for range as an argument.
    Has anyone needed to do this and has done so successfully?
    -DaverDee

    you can make a single range by making a aux table which references all the non-contiguous data and makes it contiguous.:
    You could even do this in a different table, or sheet, to hide the non-contiguous data

  • Extend System Simple Volume to Non-Contiguous Unallocated Space

    Hi:
    I have a Windows Server 2008 R2 virtual machine for which I need to extend the system simple volume on a dynamic disk to non-contiguous unallocated space.  I realize 2008 Disk Manager and diskpart cannot accomplish this but that some 3rd party tools
    can get the job done.  Does anyone recommend a specific 3rd party application that they've used for this purpose successfully, or any horror stories/products to stay away from?
    Thank you!
    Bob Herman IT Tropolis

    Hi,
    Microsoft does not provide third party software, you can backup the partition which is contiguous with system simple volume and delete it. Then, merge unallocated space to the system simple volume with Disk Management snap-in. 
    Best Regards,
    Mandy 
    If you have any feedback on our support, please click
    here .
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Acro 8 Pro - Extract non-contiguous pages?

    A client says she has this ability in a previous version of Acrobat Pro, but not in 9:
    Is there a way to extract non-contiguous pages in one operation? For example, in the Pages panel, you can select pages 1, 3, 5, and 7. Can you extract these pages? If you right-click, Extract, it seems you are forced to choose a page range. But if you right-click, Delete, you have the option to delete your group of selected pages. It would be nice to do this with Extract.

    > A client says she has this ability in a previous version of Acrobat Pro, but not in 9
    What version?
    Workaround:
    Copy the file and delete the other pages.

  • Problem trying to clue non contiguous audio regions

    I'm trying to glue together non contiguous audio regions after cutting up loop.
    I know I should get a dialogue box telling me that logic will create a new region, but this is not happening and it wont let me glue the region together, is there an option or something to turn this function on?
    any help would be great thanks

    your problem is most likely that you're trying to do this with apple loops, not normal audio files. you can't use these functions with apple loops, along with others such as fade in/out and crossfade. you'll have to export the selection to a new audio file, or bounce it.

  • Db2ldif error: Non-contiguous attribute?

    Using db2ldif to dump out a 5.0 server I've started
    seeing the following message periodically. What does
    it mean? Looked in KB and nothing seemed to pop out.
    Anything to worry about?
    [25/Jan/2002:12:01:12 -0600] - slapi_str2entry_fast: Error. Non-contiguous attribute values for access

    Hi,
    We have the same problem since this weekend.
    [22/Feb/2010:10:29:09 +0100] - WARNING<5379> - Entry - conn=-1 op=-1 msgId=-1 - Entry error Convert LDIF entry into LDAP entry. Error: non-contiguous attribute type for mailmessagestore
    [22/Feb/2010:10:29:10 +0100] - WARNING<5379> - Entry - conn=-1 op=-1 msgId=-1 - Entry error Convert LDIF entry into LDAP entry. Error: non-contiguous attribute type for mailmessagestore
    [22/Feb/2010:10:29:10 +0100] - WARNING<5379> - Entry - conn=-1 op=-1 msgId=-1 - Entry error Convert LDIF entry into LDAP entry. Error: non-contiguous attribute type for mailmessagestore
    [22/Feb/2010:10:29:10 +0100] - WARNING<5379> - Entry - conn=-1 op=-1 msgId=-1 - Entry error Convert LDIF entry into LDAP entry. Error: non-contiguous attribute type for mailmessagestore
    We have two DS (master role) replicating each other (5.2 P6) and the same errors occurs on export to LDIF, on indexation, and sometimes, on access (for this attribute).
    I already have tested to:
    - reimport data for the suffix from the other replica
    - create an index to this attribute (for testing)
    - restart the DS and restart the DS with a "forced" recovery of the database
    and no changes :( I still have that errors.
    I have checked my exports (which are my backups) and I have the same amount of occurence for that attribute. All seems "fine"...
    Any advices ?
    Edited by: olivier_delcourt on Feb 22, 2010 10:52 AM

  • 3845 Router do not work with NME-X23ES-1GP Interface card

    Need help!
    I Trying install interface card NME-X 23ES-1GP on 3845 Router. I installed this card in slot 4, but router could not communicate with this card.
    IOS version in Router 12.3
    Here is results show diag command:
    Slot 4:
    Unknown (type 1187) Port adapter
    Port adapter is disabled deactivated
    Port adapter insertion time unknown
    EEPROM contents at hardware discovery:
    Hardware Revision : 1.0
    Top Assy. Part Number : 800-25011-01
    Board Revision : A0
    Deviation Number : 0-0
    Fab Version : 03
    PCB Serial Number : FOC090009VC
    RMA Test History : 00
    RMA Number : 0-0-0-0
    RMA History : 00
    Product (FRU) Number : NME-X-23ES-1G-P
    Version Identifier : V01
    Base MAC Address : 0013.8088.9f80
    MAC Address block size : 128
    EEPROM format version 4
    EEPROM contents (hex):
    Possibly IOS release too old?

    Thank you for link. I read all information on this link. But I can't solve the problem.
    Commands "show version" and "show flash:" show my the IOS image file version on Router (but not on interface modules). Here is Routers IOS image:
    c3845-advipservicesk9-mz.123-11.T5.bin
    I Can't connect to and open a session on the interface module. Command service-module interface slot/port session don't work.
    What I should do next?
    May is ncessarily upgrade Software on router?
    Here is results show version and show flash:
    BIG1#show flash:
    -#- --length-- -----date/time------ path
    1 29801400 Jun 28 2005 04:47:46 +00:00 c3845-advipservicesk9-mz.123-11.T5.bin
    2 1651 Jun 28 2005 04:55:18 +00:00 sdmconfig-38xx.cfg
    3 3085312 Jun 28 2005 04:55:40 +00:00 sdm.tar
    4 763392 Jun 28 2005 04:55:56 +00:00 es.tar
    5 820224 Jun 28 2005 04:56:10 +00:00 common.tar
    6 1038 Jun 28 2005 04:56:24 +00:00 home.shtml
    7 113152 Jun 28 2005 04:56:36 +00:00 home.tar
    8 749101 Jun 28 2005 04:56:52 +00:00 256MB.sdf
    9 1208320 Jun 28 2005 04:57:08 +00:00 ips.tar
    27451392 bytes available (36560896 bytes used)
    BIG1#show version
    Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.3(11)T5, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2005 by Cisco Systems, Inc.
    Compiled Sat 02-Apr-05 15:14 by yiyan
    ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
    BIG1 uptime is 57 minutes
    System returned to ROM by reload at 07:11:45 UTC Tue Jul 12 2005
    System image file is "flash:c3845-advipservicesk9-mz.123-11.T5.bin"
    Cisco 3845 (revision 1.0) with 223232K/38912K bytes of memory.
    Processor board ID FCZ0927714C
    2 Gigabit Ethernet interfaces
    1 Virtual Private Network (VPN) Module
    4 Voice FXS interfaces
    DRAM configuration is 64 bits wide with parity enabled.
    479K bytes of NVRAM.
    62720K bytes of ATA System CompactFlash (Read/Write)
    Configuration register is 0x2102

  • Error: there are non exicisable item with cenvat tax code

    I am getting an error message there are non exicisable item with cenvat tax code while trying to add po for pick and pack from sales order. I request all of you to help me with it.
    I have already checked if the item and ware house is exicisable in the check box of the master data.
    Best regards,
    Sandesh.Sreyamsh

    Thanks mahendra and rahul,
    Unfortunately my issue is not solved yet, the tax is not manually created it was created by sap during new company creation. I checked by adding other tax type in sales order but every time when I try to create sales bom it gives the above error.
    @ Rahul the tax is under cenvat type and the Items has been added under exercise transaction. here is what im trying to do
    I created a sales order for 4 of my items.
    Then i try to create po for two of my as pick and pack items by checking Purchase orders indicator under logistics tab of sales order.
    At this point i am getting the above said error.
    All the items i am trying to add is exisable and tax is also of cenvat type.
    Please help me out of this as im stuch very badly in this issue.
    Regards,
    Sandesh.Sreyamsh

  • I've set up email on my iPad (talk mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this

    I've set up email on my iPad (talktalk.net) and can send and receive mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this?

    I've set up email on my iPad (talktalk.net) and can send and receive mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this?

Maybe you are looking for