Routing vs work scheduling

Hi Sir/Mdm,
Example: Under Routing CA03 - There are 1 operation namely Assembly 1 with labour time of 0.4 hours to produce 1 part. To produce 10 parts, I will require 0.4x10 = 40 hours. If I have two Assembly 1 station and to produce the same 10 parts, I will only require 20 hours. How can I reflect the additional work station capacity in the routing or work scheduling?

Hi Bala,
Thanks for the advice.
I realised that by playing with parameter "Splitting" under Operation details will also help in the work scheduling other then changing the capacity as what you mentioned.
Anyway, I have awarded reward points for your advice.

Similar Messages

Whether MRP can be carried out for work scheduling GR. 20 i.e. work to orde

Dear Experts,
Whether MRP can be carried out for work scheduling GR. 20 i.e. work to order.
mahendra

Hi MShirodkar,
Yes, s and it specifies the time needed to process the material in the operations at the different work centers.
The GR processing time depends on the order quantity.
The GR processing time is required to calculate the lot size dependent in-house production time. The system then uses the in-house production time to determine the planned dates for planned orders in materials planning.
You can define work scheduling times in the material master record in one of two ways.
Either you enter the in-house production time. If required, you can get the system to update this value from the routing.
Or you enter the setup, teardown, processing, and interoperation times. If you maintain these values, the system determines the in-house production time on the basis of lot size.
I hope it clears you doubt any queries please revert me back.
Regards,
Madhu.G

Work scheduling view-material master

Hi, wht is meant by lot size depenedent parameters and lot size independent parametrs? how to use that data in manufacturing industry? pls advise.

Dear Yadav,
case1: If you have maintained the Inhouse production time for any product in the MRP2 view,this get's automatically reflected
in Work scheduling view as lot size independent Inhouse production time.
At this point if basic scheduling is carried out during MRP then the date calculation will be based upon this number of days
irrespective of the order quantity.
case2:Once after maintaining the operation timings in the routing,you can update the same using CA97,for the relevant task list
type ,group and group counter no and include the check box for update material master directly,you can find the timings
maintained on hour basis in the setup,processing and inter operation (This calculation is based on the timings maintained in the
routing and also your work center capacity details,like the number of hours this capacity will be available for a day).
Once after performing this,even if you have maintained the inhouse production time in days,that value gets removed.
This time will be considered for basic scheduling purpose during MRP.
So in my understanding this will be helpful during the scheduling purpose for the date calculation.
Check and revert back with your further queries.
Regards
Mangalraj.S

Time Management - Work Schedule /Absence Quota / Part-time quota generation

Hi Experts,
Need your help!
We have a requirement where we need to create distinct work schedules for each irregular / part-time work pattern and the number of work patterns we have identified is more than 1000. We are using report RPTQTA00 to generate quota. We have used work contract, employee sub-group & employee payscale group in the QUOMO feature to get the base entitlement picked up. We have defined base entitlement for the full time workschedules with 37.0 / 38.5 hours and there is a reduction rule which reduce the absence entitlement for part time employees as per the employement percentage in IT0007. Now we have a scenario where we have created a work schedule with different no of hours for each day of week (M-4, T-6, W-4, TH-6, F-4, S-OFF, SU - OFF); this work schedule is treated as full time work pattern by the system and quota is generated as full time work schedule refering to the QUOMO settings, but as per my client employees with this work schedule have reduced hours of working hours (24 hours, not 37.0 or 38.5 hours)and hence it should be treated as part-time employees, and the quota generated should be proportionately reduced. I have very limited scope to create any ESG or PSG as we do not have any distinct emplyee sub-groups maintained for full-time and part-time employees and the project has already gone-live with payroll/time. It is worth mentioning over here that we are recording absence through ESS and it takes into account the daily planned working time maintained in IT0007, so we are very particular to keep it as accurate as possible.
I would really appreciate if somebody can please suggest any possible solution for the above issue, or guide me on what would be the best way to tackle it. I can give more details in case anybody need to have a better understanding of the issue to suggest a solution.
Thanks in advance
Sujit

Hi Kathy,
Yes, i have found the solution to it. I do not know whether it will fit into your situation or not, but i got two solutions for my issue mentioned above, please check it may help:
1) To use capacity utilization field in IT0008 to get the FTE hours and defining the reduction rule of absence quota based on the capacity utilazation percentage.
2) There are three user exits available in the standard report RPTQTA00, i have used one of them to write my own rules for the calculations (deduction rule)
Do let me know if i can help you in any respect. Thanks.
Regards,
Sujit

How do I Get My Router to Work With iChat ? FAQ 2

Replaces iCh: FAQ 2 How to get my router to work with iChat?
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have.
Routers seem to fall into two categories
Those that work straight from the box. See Apple Doc 93333
NOTE
This Doc has not been updated since Jan 04
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255).
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
DMZ Demilitarised Zone
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN)
NAT Sometimes called NAPT and related to Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You will need to set an incoming IP address (Usually 0.0.0.0 for any outside server), a port that data will arrive on, the Inside computers IP address (your computer) and the port it will deal with the data on and the protocol it will use.
iChat uses TCP and UDP so some devices will need the settings done twice, once for each protocol.
See Apple Doc 93208 for more information.
Note:
Note 1 should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, which need to be open for TCP only.
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678. When you click on the invite window the process moves to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP
Wireless
Here you will have to read around but this Apple Doc 58514 might be a good starting place.
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my pesonal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding.
Ralph
G4 Dual 1Ghz MDD with extra HDs X3. Mac OS X (10.4.3) Have you read the iChat FAQs ?? They have moved to Users Tips

Replaces iCh: FAQ 2 How to get my router to work with iChat?
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have.
Routers seem to fall into two categories
Those that work straight from the box. See Apple Doc 93333
NOTE :This Doc has not been updated since Jan 04
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
DMZ Demilitarised Zone
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN)
NAT Sometimes called NAPT and related to Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You will need to set an incoming IP address (Usually 0.0.0.0 for any outside server), a port that data will arrive on, the Inside computers IP address (your computer) and the port it will deal with the data on and the protocol it will use.
iChat uses TCP and UDP so some devices will need the settings done twice, once for each protocol.
See Apple Doc 93208 for more information.
Note:
Note 1 should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, which need to be open for TCP only.
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678. When you click on the invite window the process moves to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP
Wireless
Here you will have to read around but this Apple Doc 58514 might be a good starting place.
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my pesonal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding.
With thanks to Macmuse.
Ralph
G4 Dual 1Ghz MDD with extra HDs X3. Mac OS X (10.4.3) Have you read the iChat FAQs ?? They have moved to Users Tips<</a>/span>

HELP PLEASE !!! Can't get Linksys router to work.

Okay, I am a new owner of an Alu-imac 2.4 ghz !!!!!!
Installed Leopard last night and wanted to get my internet set up and ……. IT DIDN'T WORK !!!!!!!!
The Diagnostic thing wouldn't recognize my internet.
(Info for you):
1) I have an Linksys wireless router that is right behind the computer. I have to have a router for my 360 and my PS3 across the room. So I had the cable internet modem hooked to the wireless router and then to the computer. (just like it was hooked up to my PC)
2) I tried everything I could think of to get it to work. The diagnostic show that the Ethernet had a green light, but it would not let me online at all.
3) So then I tried unplugging the modem and the router and still nothing. (It gets stuck on the page where it asks "do you use a cable modem, if so please restart it and then hit continue") And still nothing.
4) So then I tried to just run the internet straight from the cable modem to the imac, and this didn't work either….. Then for some reason like a 1/2 later the network settings brought up the IP and everything and I had internet.
5) *But I need my Linksys router to be used !!!!* Is there any advice any of you can give me !!! I can call Linksys if I need to when I get off work, but I thought maybe some of you could help me first. *I did have to call Linksys before I could get the router to work on my old PC as well*, so maybe it's something with them ????
HELP PLEASE !!!! I want to love my Imac so much.

fonz500, are you still having this issue or is this now a dead thread?
Let us know if your still need help.

Function module to get holiday class from work schedule for current day

I need to determine what the public holiday class value is for the current day in a user exit. Is there an SAP function module that can return me this data? This would be the information that is displayed when pressing the work schedule button from infotype 0007

Function module HOLIDAY_CHECK_AND_GET_INFO is closer to what I need. This function module returns an X if the day is a holiday. I will create a Z program and instead of returning an X for a holiday I will return the THOL-KLASS (holiday class) value.

Report to check work schedule - If case more than hundreds of work schedule

dear experts,
I have one issue to create work schedule for the next year. I want to create(pt01) active work schedule for the next year(2012).
However i have issue because I don't remember which work schedule still active.This is because we have hundreds
of work schedule rule based on emp sub group grouping, holiday calendar,psa grouping and w schedule rule.
Is there any reports to check all the active work schedule .I'm afreaid ihave missing certain work schedule for next year...

If you use the IMG node for automatic generation of Work Schedule Rules
(Time Management > Work Schedules > Work Schedule Rules and Work Schedules > Generate Work Schedules in Batch)
you can generate all work schedules associated to a Holiday Calendar
and only the active work schedules will be generated.

Update to kichat: FAQ 2 - How to get my router to work with iChat?

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

How to fix an error (related to work schedule rule) in Time evaluation ?

Hi experts,
I am getting an error while running time evaluation - PT60.
Find the log
Log:TimeEvaluation General data
Schema ZM04 Time Evaluation Without Clock Times
00753402 Christoudas Natalie
Customizing error in work schedule rule 1 VM 01 5MTWTF Person rejected: 00753402
How to fix it? Its urgent.
Be assured of points for useful answers.
Rajesh

Hi All,
I have checked work schedules and work sc. rules. everything looks fine. Reason being fine, same work schrdule rule, i.e. 5MTWTF is used for other employees, whose payroll area, personnel area, personnel subarea, employee group and employee subgroups are same.
Why it is throwing error for one employee 753402.
I am providing you more information. In table V_T569r, if u select recalculation category as time evaluation, it is mentioned as 01.01.2003. Initially, one action called "Conversion take on" has been maintained as on 01.03.2002, where employee had payroll area -99 (payroll irrelevant) and personnel subarea - DAYY.
Then on 17.03.2008, another action ran "Conversion initial reassignment" where payroll area changed to "MT - monthly", subarea changed to DAYF. At that time PDC recalculation date in infotype 0003 was 01.03.2002 which was before recalculation date, i.e. 01.01.2003.
Time evaluation was throwing 2 error messages. one was solved by changing PDC recaluation date to 17.03.2008. But other error related to work sc rule 1 VM 01 5MTWTF still occurs.
Can some body now provide some useful information?
Thanks
Rajesh

Looking for an app that is easy to create a work schedule on PC and download to phone.

We have a small group of managers who have blackberry's and were wondering if there is an app that would allow us to easily download our individual schedules to our phones. We currently use excel to create the work schedule and even though we can view it through email it would be nice be able to plug it in with our calendars. Any help would be Great!

Are you all using BES or BIS? If you're not on a BES then you can use a program called Google Sync. If you all have a gmail account you can use this program to wirelessly sync between your BlackBerry calendar and Gmail calendar. Read more about it here
http://www.google.com/mobile/blackberry/sync.html
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

Error "No entry in table T551A" while creating set work schedule rule.

Dear Team,
I am getting following error while creating set work schedule rule.
Error "No entry in table T551A" for key 22 BBB [ here BBBB is my period work schedule]
The actual prob is i configured all the necessary steps but when i tried to create work schedule rule im getting this error. Also, in the same screen there is one field DWS grouping initially value in this is 00 and gread mode. But after giving ES grp, holiday calander ID etc etc when i try to save that screen that value is chainging to 22 from 00.
My ES grop=2 and PS grop=2 . Is that value is my ES and PS grouping..?? or some other thing.
Request you to please help me out.
Regards
Shab.

HI, there are 8 steps you need to do below:
1. Group Personnel Subareas for the Daily Work Schedule
2. Group Personnel Subareas for the Work Schedule
3. Define Break Schedules
4. Define Daily Work Schedules
5. Define Period Work Schedules
6. Define Employee Subgroup Groupings
7. Define Groupings for the Public Holiday Calendar
8. Set Work Schedule Rules and Work Schedules
All of them belong to TIME MANAGEMENT. I think you miss some steps above.
Please check it again.
Regards!
Minh

Error message while Creating Work Schedule

Hi,
While Hiring an Employee, and creating a work schedule, using the work schedule rule NORM, the error message "No work schedule rule for key 2 00NORM 20100501 ##"
How do I rectify this issue?
Regards,
Arvind
Please Type the Error in the search forum ............ feild you will find lot of threads related to this issue

check your PSA grouping in V_001P_ALL

Change/ removal of Unit of Issue in Material master Work scheduling view

Hi,
Is there a way to remove Unit of Issue from Work scheduling view? it is giving error message as "this is being used in BOM". Even if we put deletion indicator also it is showing same error message.
Regards,
R. Srinivasan

Do a CS15 for the material in question and make sure you go in the BOM and select the material and click on delete/remove you can then do this.
I have tested it and it works.
Regards
Adeel

Need Help in Calculation of Paid and Unpaid Break in Daily Work Schedule

hai,
I am a student of SAP-HCM. I am having problem with the calculation
in Paid and Unpaid Break in Daily work schedule (Time Management).
Please help.
thank you
Dev.

Hi,
The above screen shot is table where we maintain unpaid and paid breaks, we mention about when a break has to start under START tab and when it has to end under END button.
Under UNPAID and PAID tabs we mention duration of break, if its 15 mins break or half an hour or one hour depending on start and end timings.
Suppose a shift is for 9 hours in total and client wants there should be a paid break of one hour, then out of this 9 hours shift itself break would be considered.... and in case client wants unpaid break then shift would be for 10 hours out of which 9 hours will be working hours and one hour break.
When this concept has to be calculated in schema processing type would be assigned to this time pair showing break accordingly either paid or unpaid.

Routing vs work scheduling

Similar Messages

Maybe you are looking for