RSM 5302 put Vlan in down

I had a strange issue on my Catalyst WS-5500 with RSM-5302 where I had 10 Vlan configured in HSRP mode with another Catalyst redundated on the same site.
In certain condition the Vlan11 close the communication with the switch and nobody on the LAN can work anymore.
I have no log on the RSM neither in Catalyst !
The only way is to reload the RSM (both side: primary and backup) and the connectivity restart.
I think its an HSRP problem
But the priority is correct
Anyone have some idea?
Thanks a lot!

I am sorry for the late .
But It happen again :
Jun 20 07:55:23.802: %C5IP-0-MSG: slot0 %DB-0-RESTART: Waiting for restart
Jun 20 07:55:24.810: %DBUS-3-DBUSINTERR: Slot 0, Internal Error
Jun 20 07:55:27.202: %RSP-3-RESTART: cbus complex
We change already :
Chassis
RSM 5302 ( routing module)
this is the config :
Current configuration : 4854 bytes
! No configuration change since last restart
version 12.2
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
no service password-encryption
no service single-slot-reload-enable
hostname wpa-lansrv-01-cstel
boot system flash slot0:c5rsm-isv-mz.122-7c.bin
logging buffered 128000 debugging
aaa new-model
aaa authentication login default group tacacs+ local
aaa authorization exec default group tacacs+ local
aaa authorization network default group tacacs+ local
enable secret 5
username wpa-lansrv-01-cstel password 0
clock timezone MET 1
clock summer-time MET-DST recurring last Sun Mar 2:00 last Sun Oct 2:00
ip subnet-zero
ip cef
ip tftp source-interface Loopback0
ip domain-name wind-lan
ip name-server 10.154.225.101
ip name-server 10.154.225.102
interface Loopback0
ip address 10.x.x.x 255.255.255.255
interface Vlan1
description Vlan di Management
ip address 10.x.x.x 255.255.255.0
no ip redirects
standby 100 ip 10.x.x.x
standby 100 priority 200
standby 100 preempt
interface Vlan2
description Vlan di Trasporto
ip address 10.x.x.x 255.255.255.248
ip access-group 173 out
interface Vlan3
description Vlan di Trasporto
ip address 10.x.x.x 255.255.255.248
ip access-group 173 out
interface Vlan5
description Vlan Servizi
ip address 10.x.x.x 255.255.255.0
no ip redirects
standby 5 ip 10.x.x.x
standby 5 priority 200
standby 5 preempt
interface Vlan10
description Piano Terra CC
ip address 10.154.233.252 255.255.255.0
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
no ip redirects
standby 10 ip 10.x.x.x
standby 10 priority 150
standby 10 preempt
interface Vlan11
description Primo Piano CC
ip address 10.154.235.252 255.255.255.0
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
no ip redirects
standby 11 ip 10.x.x.x
standby 11 priority 200
standby 11 preempt
interface Vlan12
description Secondo Piano CC
ip address 10.x.x.x 255.255.255.0
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
no ip redirects
standby 12 ip 10.x.x.x
standby 12 priority 150
standby 12 preempt
interface Vlan20
description Piano Terra CC 2
ip address 10.154.232.252 255.255.255.0
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
ip helper-address 10.x.x.x
no ip redirects
standby 20 ip 10.x.x.x
standby 20 priority 150
standby 20 preempt
interface Vlan23
description TEST
ip address 10.x.x.x 255.255.255.0
ip helper-address 10.x.x.x
no ip redirects
standby 23 ip 10.x.x.x
standby 23 priority 200
standby 23 preempt
router ospf 69
log-adjacency-changes
passive-interface default
no passive-interface Vlan2
no passive-interface Vlan3
network 10.x.x.x 0 0.0.31.255 area 10
ip classless
ip tacacs source-interface Loopback0
no ip http server
ip ospf name-lookup
ip pim bidir-enable
Many thanks for your help

Similar Messages

  • HT1338 How do I eject a dvd that may have been put in upside down by my toddler?

    How do I manually eject a DVD. It may have been put in upside down.

    Depress the mouse pad on startup. Should eject.
     Cheers, Tom

  • I was typing a n e-mail to my friend. I put the iPad down to answer the door and came back a few minutes later. The screen had gone blank and when i tried to get the message that i was typing back I could not find it. It was a lot of typing and pictures.

    I was typing an email to friend. I put the ipad down to answer the door and came back a few minutes later and the screen had gone blank and when I tried to get the message that I was typing back I could not find it.  The message contained a lot of text and pictures.  How can I find it? I have looked in drafts.

    Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    Wait for the Apple logo to Appear...
    Usually takes about 15 - 20 Seconds... ( But can take Longer...)
    Release the Buttons...

  • I can't access to control center (Swipe up), notification center (swipe down) and camera on my home screen when i put my phone down

    I Just bought my iphone 6 64GB iOS 8.1.2 few days ago , It can't access to control center , camera (swipe up) and notification center (swipe down) on home screen when i put my phone down (it also hardly to access assistive touch too ) . Is anyone having this situation too ?

    Are you using a iphone case or otterbox?  If so remove the case and see if you can swipe up.

  • Hi there I'm wanting 2 phones 1 for wk an a good ph for out of wk on 1 SIM card so I can finish wk put that ph down an use my good ph not call diversion , all these flash apps an you can't do this from any ph so I've been told iPad, iOS 6.1.3

    Hi there I'm wanting 2 phones 1 for wk an a good ph for out of wk on 1 SIM card so I can finish wk put that ph down an use my good ph not call diversion , all these flash apps an you can't do this from any ph so I've been told
    iPad, iOS 6.1.3

    why don't you post using full words, no abbreviations, and proper punctuation?  Then perhaps your question will actually be legibile.

  • I put accidentally upside down a music CD and it won't go out and it does not read it. How could I eject it?

    I don't know how to eject a music CD, that accidentally i put it upside down. And the computer doesnt read it. Please, someone could help me?

    all known methods to force eject a stuck cd from a mac:
    First try the normal methods to remove the disc. Drag its icon to the trash can in the dock or select 'Eject' from the File menu.
    If you are running a virtual machine, e.g. VMFusion, ensure that the CD is disconnected from the virtual machine. This will sometimes allow the CD to now show up in Mac OS X.
    Shut down the computer and start up whilst holding down the mouse button. This may take some time, but keep your finger on the mouse button right up until the disc comes out or the log-in screen has appeared.
    If you have Toast Titanium installed on your computer, choose EJECT DISC from the menubar.
    Sometimes you can successfully use the eject disc button in iTunes even if the disc is not visible to the Finder
    Open Disc Utilityand choose the disc you wish to eject in the left-hand pane, then click on the Eject button.
    Some Macintoshes have a paperclip hole that you can insert a straightened paperclip into, manually triggering the eject mechanism.
    Open Terminal and type "drutil tray eject" to eject the disc/tray, and "drutil tray close" to close the tray.
    If your computer has an eject button on the keyboard, restart the computer holding down the Option key. When the startup disk selection screen appears, let go of the option key and press the keyboard's eject button.

  • HT4583 MY IPHONE STARTED SMOKING YESTERDAY WHILE I AS USING IT. AS I AS PUTTING THE PHONE DOWN THE BATTERY EXPANDED AND BLEW UP IN MY HAND. NOW I HAVE ACID BURNS FROM THE BATTERY NOW I HAVE ACID BURNS ON MY HAND. WHAT CAN I DO????

    MY IPHONE STARTED SMOKING YESTERDAY WHILE I AS USING IT. AS I AS PUTTING THE PHONE DOWN THE BATTERY EXPANDED AND BLEW UP IN MY HAND. NOW I HAVE ACID BURNS FROM THE BATTERY NOW I HAVE ACID BURNS ON MY HAND. WHAT CAN I DO????

    Definitely see a doctor.
    If the phone was under warranty, make an appointment at the genius bar. Actually, you can do that even if it wasn't under warranty (and probably should).
    FWIW, nearly every documented case of this happening can be traced to liquid damage or a botched 3rd party repair.

  • My mac book air doesnt turn off and if i put the screen down doesnt sleep

    My mac book air doesnt turn off if i click on shut down . it is not sleeping either. if i put the screen down it keeps turning on and the apple logo keeps blinking. it only turns off if i press the power button for few seconds . Please help. Another thing is condensation . i opened my mac 2 days ago there was water on keys and on the screen I guess extremes of temperature caused moisture to develop. What seems to be the issue with its turning off and sleeping. Thank God the water didnt short circuit it. Its still working but just not sleeping or shutting down normally. Please help needed. I love my MAC and cant afford to loose it ! HELP !!

    You will want to show it to an AASP to have it checked.

  • Ip address on created Mangement VLAN shuts down 255 VLAN 1.0 subnet

    My predecessor created a VLAN 255 to replace VLAN 1 as the Management VLAN.  I noticed a some of the switches had there IP's on Fas0 out of band interface. To me it made more sense to put that ip address on a int vlan 255 on all the switches. As I did to my 4th Core Switch I added the ip address *.1.24 and it shut down the entire 255 vlan with affect the .1.0 subnet.  I for the life of me can can't figure out what is causing the problem. It is not like any other device is using the 1.24 ip address and even if it was it should affect access to that device not all other devices on the 1.0 subnet.
    The message in the log (doing the show log command) only shows interface 255 going up and down. The subnet mask is 255.255.255.0 (/24).  I just put the ip in the interface again and pinged devices in the 1.0 subnet when I brought the interface back up yet I could not access any services on the 1.0 subnet from my workstations. I shut the interface again and could access services In that subnet again.

    The VLAN is in the trunk. shouldn't that be enough as for as putting it in the port goes?  I already have the interface shut and configured. When I unshut the entire .1.0 subnet does down. To me it's just so unlogical.

  • Vlan interface down

    How do figure out why? I tryed no shut down, still down...
    41-Switch-1#sh int vlan 3
    Vlan3 is down, line protocol is down
    Hardware is EtherSVI, address is 000a.f421.e800 (bia 000a.f421.e800)
    Internet address is 10.7.41.210/24
    MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input never, output never, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
    Queueing strategy: fifo
    Output queue: 0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts (0 IP multicast)
    0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 1 interface resets
    0 output buffer failures, 0 output buffers swapped out

    Thanks for helping actually i was reading this part from book
    There are no SVIs active on the MSFC-not even VLAN 1. Let's add an SVI for VLAN 20 and see what happens:
    Code View: Scroll / Show All
    MSFC-6509# conf t
    Enter configuration commands, one per line. End with CNTL/Z.
    MSFC-6509(config)# int vlan 20
    MSFC-6509(config-if)# ip address 10.20.20.1 255.255.255.0
    MSFC-6509(config-if)# no shut
    MSFC-6509(config-if)# ^Z
    MSFC-6509#
    17w2d: %LINK-3-UPDOWN: Interface Vlan20, changed state to down
    17w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down
    MSFC-6509#
    MSFC-6509# sho ip int brief
    Interface IP-Address OK? Method Status Protocol
    Vlan20 10.20.20.1 YES manual down down
    The SVI is now there, but it won't come up. The SVI will not come up unless there is an active port in the VLAN in layer two. I often forget this fact and, after adding the SVIs, go off to create my VLANs only to find that none of them will come up. To illustrate the point, I'll assign an IP address to the CatOS management interface SC0, and place it in VLAN 20. This will put an active device in the VLAN:
    CatOS-6509: (enable) set int sc0 20 10.20.20.20 255.255.255.0
    Interface sc0 vlan set, IP address and netmask set.
    Now, with something active in VLAN 20, the VLAN 20 SVI comes up in the MSFC:
    Code View: Scroll / Show All
    MSFC-6509# sho ip int brief
    Interface IP-Address OK? Method Status Protocol
    Vlan20 10.20.20.1 YES manual up up
    Now i know that Sc0 management IP of Cat OS is assigned at switching side.and we can assign only 1 ip at switching side which is using CatOS right?

  • Cisco 2950 VLAN shutting down

    Hi,
    i have got cisco 2950T-24, in that vlan 2 has got ip address of 10.1.1.1 /24, it is up & running, now when i create vlan 3 interface & type "no shutdown", vlan 2 interface goes down, why is that so? how to i make both the interface up & running?

    As others have said you are not creating a vlan , you are creating a layer 3 SVI . This is used to manage the switch only and thus you only need one address to do this , thus the switch shuts down the other SVI. To create a layer 2 vlan just do a "conf t" enter, type vlan XX where XX is the vlan number you want to create, enter . Verify with the "show vlan" command , should show the vlan you just created and it should show active .

  • Please help after being on phone to bt about my slow internet, to be told that the best I can get, I put the phone down...but gone to turn my iMac on and Safari will not open I have tried to push reopen button but keeps going back to same menu sayin

    ssafari quit unexpectedly I keep pressing reopen button but nothing. Bt told me to put imac into safe mode, could this be the problem.

    Eustace
    Thank you so much for replying.  However I was about to remove this post.  I worked out how to do it!
    If anyone is having similar issues then turn off mirroring and change the arrangement in display preferences so that the monitor works as the main display and the macbook just shows the desktop.  I then turned down the brightness levels on the macbook to conserve power.
    Feel very proud of myself, but thank you!
    S

  • My macbook pro is getting really hot when I leave it running but put the screen down.   When I open it only shows password box not rest of screensaver.  I'm not doing anything differently

    The past 2 days my MacBook pro has been running really hot, especially when I close it.  When I open it the screensaver doesn't show completely.  Yesterday when I moved the mouse it made spiral trails with the graphics, very strange.  I'm really concerned!  Help... I've restarted it, powered it off last night, etc.

    You can always take your Mac in and give it a check-up for free. What will cost you is the repairs you select to have preformed. I recommend shutting your Mac down before you go to bed. Problem solved. There is no need for you to keep it running if all applications are quit. Why do you need it on?

  • The keyboard has become positioned near the top of the screen. How can I put it back down the bottom ?, The keyboard has become positioned near the top of the screen. How can I put it back down the bottom ?

    My keypad has become positioned at the top of the screen,hiding the text I am writing. How can I reposition it at the bottom of the screen?

    Hold down on the button iwht the keyboard on it (lower right of hte keyboard), after a few seconds a dialogue box will pop up offering you to redock the keyboard. choose it and it moves back where it was.

  • VLAN 1 down

    Hi,
    My Cat6 is running on intervlan routing (L3), with Vlan 1 shutdown status (coz I don't wan to utilize VLAN 1).
    But recently, need to enabled that for some unforeseen cases. But once I've enabled it, the VLAN won't come up.
    Experts, any idea ??
    Thanks

    only can show you one of the switch trunk status..didnt managed to capture the other switch status.
    SW1> (enable) show trunk
    * - indicates vtp domain mismatch
    # - indicates dot1q-all-tagged enabled on the port
    $ - indicates non-default dot1q-ethertype value
    Port Mode Encapsulation Status Native vlan
    1/24 on dot1q trunking* 1
    Port Vlans allowed on trunk
    1/24 1
    Port Vlans allowed and active in management domain
    1/24 1
    Port Vlans in spanning tree forwarding state and not pruned
    1/24 1
    hope this helps.

Maybe you are looking for

  • A totally different project is played when project is played in full screen view and project is not editable

    Hi I have problems with my imovie 09. After several days of work with an imovie project I was again about to start editing my project after startup of my mac. I played through the project and everything seemed fine, but when a movie clip was moved in

  • Unplug of private interconnect cable restart the system!

    Dear All, My Database is 2 Node RAC Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production on Linux. I had a strange experience with my private interconnect between the 2 nodes. I need to replace switch between the nodes with a

  • REUSE_ALV_GRID_DISPLAY

    Hi, I am using the REUSE_ALV_GRID_DISPLAY to display my list. I want to save the data from the displayed list in an excel file. My question is I don't see any icon saying 'spreadsheet' in the toolbar. Where as if we use REUSE_ALV_LIST_DISPLAY functio

  • 100% CPU load but no clue in thread dump, EP. Win a bottle of champagne...

    Hi, We are suddenly facing 100% CPU load in our EP cluster (5 x 8-way Xeon multiprocessor machines). We have a serious performance problem that is burning a lot of our time and causes a lot of stress for over 3 weeks now. We have taken tens of thread

  • Hide Region from Dynamically

    Hi, everyone Is it possible to dynamically hide a region? I have an HTML region with an <IMG> in it and i want to hide it after a report is fully displayed. am i able to do something like this? Thanks in advance Daniel