RSV 400 best solution for this scenario?

Hi
As shown in the diagram below, I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pc’s at remote offices has IP communication with the server from the central office using a static route.
Does the solution would be to put some VPN routers between each LAN and the operator’s routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network?
I had thought to use RSV400 routers, Is this the most appropriate equipment for what we want to do?
Thank you very much for the help

Originally Posted by kjhurni
This is just my opinion, of course, but:
If you don't want to have to migrate your NSS data and keep the same server names/IP/s and cluster load scripts, then I believe a Rolling Cluster Upgrade is a good way to go.
If you look in my signature, there's a link to my OES2 guides. Somewhere there is one that I did for our Rolling Cluster Upgrade.
If all you have is NSS and iPrint, then you only need to use the miggui (migration utility) for iPrint--or so I think (I do have to followup on this one as I vaguely recall I asked this a while back and there may have been a way to do this without migrating stuff again).
But your NSS data will simply "re-mount" on the OES11 nodes and you'll be fine (so that's why I like the rolling cluster upgrades).
Let me double-check on the OES2 -> OES11 cluster option with iPrint.
--Kevin
Thank you Kevin for your answer.
Finally, I think Im going to proceed using transfer ID on my servers that Im only using NSS over NCS (I only have two machines with one NSS volume)
because it seems that its a good option. I would like to keep old IPs from all the servers, cluster and resources if possible. So, testing this
migration on my test environment it seems that it works fine:
- I use miggui for transfer id between all the machines: physical -> physical and virtual -> virtual. eDirectory assumes new hostname, IP, etc.
the only task "out of the box" is that I have to delete the cluster and regenerate (reconfigure NCS on the new servers) but its pretty easy. This way
I have the two old ips from the older machines and all the ips from the cluster and the cluster resources also. I think that its the best plan.
For the other two machines that has 4 nss volumes and iPrint I must think about a plan. But with those, Im going to proceed this way. I hope
I have chosen a good plan!
thank you so much all for your answers / advices

Similar Messages

TA24002 My 500 GB can't verify nor repair. I have photoshop work that I need to recover. I would like to know which erase option would be the best solution for this problem.

My 500 GB can't verify nor repair. I have photoshop work that I need to recover. I would like to know what option would be the best solution for this problem?

You appear to have two issues: 1) a hard drive that is not working properly and 2) files you wish to recover.
Re 1) you need to answer Kappy's questions.
Re 2) does the drive load and can you see your photo files? If so can you copy them to another drive?
Do you not have a backup of the photo files?

I have problems in the initiation of the Encore process when opening presents the following error message : "Encore CS6 Cannot Run in Non-Royalty Serialized".... What is the best solution for this problem ?

Help Me.
What is the best solution for this problem ?

Encore is activated when you activate Premiere Pro... so, as Stan asked, how did you install P-Pro?
Ask for serial number http://forums.adobe.com/thread/1234635 has a FAQ link
-and a fix for Encore http://forums.adobe.com/thread/1421765?tstart=0 in reply #7
-plus more Encore http://helpx.adobe.com/encore/kb/cant-write-image-fie-larger1.html

WhatÃÂ¢ÃÂÃÂs the best practice for this scenario?

Hi,
My users want the ability to change the WHERE and/or ORDER BY clause at runtime. They may define user preferences on each screen ( which is bind to a view object). They want to see the same records based on WHERE/ORDER BY defined on the last visit. That is why I keep the users preferences and load the screen based on that, using :
View.setWhereClause(...);
View.setOrderByClause(...);
View.executeQuery();
This works good when only one user working with the application but faced low performance when more than one user working with the application.
What are the points to increase the performance and what is the best practice for this scenario?
Thanks for your help in advance.

Sung,
I am talking only about 2 users in my testing. I am sure i missed something but could not recognize that.
This page is my custom query page including a tag to instantiate app module in stateful mode at the top <jbo:ApplicationModule..> and a tag to instantiate data source <jbo:Datasource...> and release tag at the bottom <jbo:ReleasePageResources..> and some java code in the middle(body). The java code constructed the query statement and then fires the query to set the view object based on the query statement using the above methods.
So, I am facing very slow performance(speed) when two clients load this page at the same time. Looks like the entire application locks for others when one client load this page and fire the query. i realized the battle neck is where executeQuery() is executing.
what do you think.
Thanks in advance for your comments.

Best plan for this scenario (migrate oes2 to oes11)

Hi there!
I would like to ask you guys the best plan for migrate a few servers that I have
in oes2 to oes11.
I have four servers in oes2sp2/sp3, these servers have a few NSS
volumes over NCS. Also I have my iPrint service on two machines,
also using NCS. I have one cluster between two machines and
other cluster between the other two machines. For exmaple,
machine1 and machine2, three NSS volumes (every NSS volume is a cluster
resource) and other resource in the same cluster for iPrint. Cluster: CL1
machine3 and machine4, one NSS volume (for other people in the company)
in other cluster. Cluster: CL2. In this cluster only have a NSS volume/resource.
Machine1/3 are physical, machine2/4 are virtual (vmware)
My CA is in other server that I will migrate after a while. So, It seems that there is
no problem with the certificate. Machine1 and machine3 are a replica for the eDir in
my organization.
My plan: I have deployed two virtual machines and one physical with oes11sp1 and sles11sp2.
I think that the best plan is migrate with migration tool iPrint first, like a cluster resource,
and NSS volumes, and after that, make a transfer ID (like a different project)
For machine1/3, move NSS volumes and after, make a transfer ID.
Is this correct? I dont know If I have to delete the current clusters (cl1 and cl2) and
create new ones, after that, create every resource as It was on the old ones.
thank you so much !
Antonio.

Originally Posted by kjhurni
This is just my opinion, of course, but:
If you don't want to have to migrate your NSS data and keep the same server names/IP/s and cluster load scripts, then I believe a Rolling Cluster Upgrade is a good way to go.
If you look in my signature, there's a link to my OES2 guides. Somewhere there is one that I did for our Rolling Cluster Upgrade.
If all you have is NSS and iPrint, then you only need to use the miggui (migration utility) for iPrint--or so I think (I do have to followup on this one as I vaguely recall I asked this a while back and there may have been a way to do this without migrating stuff again).
But your NSS data will simply "re-mount" on the OES11 nodes and you'll be fine (so that's why I like the rolling cluster upgrades).
Let me double-check on the OES2 -> OES11 cluster option with iPrint.
--Kevin
Thank you Kevin for your answer.
Finally, I think Im going to proceed using transfer ID on my servers that Im only using NSS over NCS (I only have two machines with one NSS volume)
because it seems that its a good option. I would like to keep old IPs from all the servers, cluster and resources if possible. So, testing this
migration on my test environment it seems that it works fine:
- I use miggui for transfer id between all the machines: physical -> physical and virtual -> virtual. eDirectory assumes new hostname, IP, etc.
the only task "out of the box" is that I have to delete the cluster and regenerate (reconfigure NCS on the new servers) but its pretty easy. This way
I have the two old ips from the older machines and all the ips from the cluster and the cluster resources also. I think that its the best plan.
For the other two machines that has 4 nss volumes and iPrint I must think about a plan. But with those, Im going to proceed this way. I hope
I have chosen a good plan!
thank you so much all for your answers / advices

Is JavaFX the right solution for this scenario...

Hi,
Is JavaFX the right choice for the following implementation choice I have to make? (see below for the requirement)
Requirements:
1. Provide a way to visualise within a web application an entity relationship type diagram (i.e. nodes with relationships between them). The backend database will hold the topology relationship. So to visualise this on a web application will need the ability to draw rectangles/lines/text etc.
2. Provide a way to allow the use to trigger "add a new node", or "edit info in this node". For example a right hand context sensitive menu for example.
3. Ideally will scale as the user resizes the browser window
4. Would like the main functionality of the application to remain web based (is a Ruby on Rails application in fact), but have the visualization of the diagram render within the web application as transparently as possible.
Options / Issues:
* Issues I've struck with some investigation I've done is that whilst the <canvas> tag looks good for Mozilla/Firefox etc, it does not seem to have support on InternetExplorer. Hence cross-browser compatibility seems to be a real issue for the JavaScript type solutions from what I can see. This is why I thought JavaFX may be good?
* Options therefore seem to me to be:
- javascript (e.g. <canvas> tag) => cross-platform issue
- JavaFX / Applet => (this is what I'm asking about)
- Microsoft => costs $$ for development environment etc
- AIR / Flex / Flex => ??? costs $$ again I think
Regards
Greg

thanks - I'm still a little confused re their products and which would fit best so I've sent them some questions (below if you're interested)
Hello,
Could you please assist me in understanding which of your products would satisfy my needs. In fact (a) whether JGraph itself would and if not, or if it's not ideal, (b) which other product would.
REQUIREMENTS:
1. Provide a way to visualise within a web application a connectivity type diagram (i.e. nodes with relationships between them, a network connectively type of diagram).
2. The server side (i.e. web application with database) will hold the topology relationship. HTTP type interfaces off the web application can be developed to provide the client side visualizing component with the topology data in the required format (assume this is XML)
3. As well as just visualizing in the browser there would need to be a way for user to trigger a context sensitive "add a new node", or "edit info in this node". For example a right hand context sensitive menu for example.
4. Ideally the diagram will scale as the user resizes the browser window
5. Would like the main functionality of the application to remain web based , but have the visualization of the diagram render within the web application as transparently as possible. The the visualizing component would just take topology data and intelligently display this.
6. DESIRABLE: Basic automated layout would be nice, or as a desirable (depending on cost) more sophisticated auto-mated layout.
QUESTIONS:
As well as your recommendation re which product would suite I had some specific questions which I would appreciate clarification on:
Q1 - I assume if I have a web backend that can deliver topology inforrmation in an appropriate XML format via a HTTP REST type GET call that this could be used as a the source of data for a jGraph visualisation running within an Applet?
Q2 - If running within an Applet, can jGraph cater for a right hand menu option off the nodes/links on the graph, that I could use to trigger other calls back to the backend? (e.g. to trigger an Add New Node call)
Q3 - Following on from Q2 scenario, if I trigger an add new node scenario, if I wanted to visualise the form to type in the attributes for the new node, could this be handled within the applet by jGraph, or would this be a case of just adding your own Swing based dialogs to handle this?
Q4 - Do the basic JGraph do any basic layout without having to go up to the layout Pro package (which I think costs if using it commercially).
Q5 - If the answer to Q4 is No, how difficult would it be using the base JGraph library to do a basic layout? Is this doable/recommended? i.e. how would one "layout" the diagram if using only the base JGraph component? (noting from my requirements I'm really after a component I could send my topology information to in XML form and have it just visualise it for me)
Q6 - Running the visualiation in an Applet in a browser, is the typical usage one where all changes to topology are made as calls to backend? i.e. or is there an approach where one would allow users to make changes to the topology within the applet and build up all the changes here on the client, and then at some point synch these back to the backend? (I'm assuming the keep it simple approach would be not to do this)
Q7 - Is there a sample application/project with source code that implements a JGraph in applet/browser talking to web backend for data?
Q8 - How does JGraphPro & mXGraph fit into the picture re solving my requirements in the most cost effective manner

Will use of Web Property Extractors be a good solution for this scenario?

Hi all
We have a scenario where we would like to use our existing SAP Portal
environment along with the TREX to search in a a database with 150000+
cases much similar to SAP Customer Messages.
We are thinking of implementing the following scenario:
1) We develop a custom application that extracts cases from
our "customer message application", and converts them into html-files.
2) These 150000+ html-files are published on a web server that can be
seen by the SAP Portal (and corresponding TREX).
3) We integrate this "artificial" web site into our portal using a Web
Repository Manager with configured Web Property Extractors (content is published in meta tags).
4) We set up an index and configure search iviews etc, so the
supporters are able to search in different parts of the "customer messages" (=different properties).
My questions are now:
1) Can the Web Property Extractors be used in other repository managers
(like the CM repository manager, eg) or can you set up a Web Repository
Manager to look into a file server instead of a web server or will the above mentioned scenario be the only feasible solution?
2) What considerations should be done in relation to the above scenario in order to assure good search
performance and a well performing database? We have a bunch of text
snippets (that can be very long) that we wants to extract into
properties - thus being stored in the database. Will this be a problem?
Or will it not effect performance if the database is running on a SAN?
Best regards,
Martin Søgaard

Maybe something along the lines of this A Form to Design a Form sample would suit?

Need Solution for this Scenario......

Hi All,
I am giving the scenario:
For Indian operation we have two set of books, one is for direct billing to the customers in India and the other is shipping to India and billing from Bangalore/Bombay or other branches. Though India operation is single, still for the operation purpose it should be considered as two entity/two Company. Similarly the service company under the group also has the same kind of operation structure.
How this can be done in SAP........
Thanks in Advance,
Subah Jo

Some of the container/app server vendors offer such tools. You should start by posting your question to the specific container/app server forum.

Is an array the best solution for this problem?

Hi there,
I'm working up a demo where a couple of little games would show up in a panel. There is a main menu that you bounce around to select things (the games as well as other apps.)
When a single game is running, it takes up the whole panel. When two or more are running, they run in a "mini" format. Also, when a game is running, a special "return to game" button appears in the main menu.
This is a click through dog and pony show demo. It's not a production app, but it has to work well enough to be played around with by internal clients. So it has to work well.
Right now I have some variables set up like so:
var gameActive:Boolean = false;
var gameDual:Boolean = false;
In my launch game and menu function, I am checking these (and one or two other) variables to see if I should do things like show a mini version of the game or show the return to game button. As I add features though, this is becoming slightly unwieldy.
The key issue is the games. Let's say I have only two. I could make an array, and then load in the game name when a game is launched. I could check this array in my functions to see not only if games are launched, but which game is launched so I can use the full or mini games as appropriate.
Is this a good approach, or is there a better way? I'm rusty with my coding and not super comfortable making objects right now. But I could go that way if it was the best.

there's not much to it. here are the only 3 things you're likely to need to do with your associative array:
var yourAA:Object={};
function addAAItem(aa:Object,o:DisplayObject){
aa[o.name]=o;
function removeAAItem(aa:Object,o:DisplayObject{
aa[o.name]=null;
function aaLength(aa:Object):int{
var i:int=0;
for(var s:String in aa){
i++;
return i;

I have a friend trying to update iOS7 using an ipad mini but during the process there is a message failed to update...whats the best solution for this??

need our help guys...thanks and more power

Apple's servers are being hammered by everyone and his dog trying to get the update the minute it was released. I'd suggest he/she wait a few hours, or perhaps until tomorrow, and then try again.
Regards.

SQL Server 2012 - Wat Is The Best Solution For Creating a Read Only Replicated/AlwaysOn Database

Hi there I was wondering if someone may have a best recommendation for the following requirement I have with regards setting up a third database server for reporting?
Current Setup
SQL Server 2012 Enterprise setup at two sites (Site A & Site B).
Configured to use AlwaysOn Availability groups for HA and DR.
Installed on Windows 2012 Servers.
This is all working and failover works fine and no issues. So…
Requirement
A third server needs to be added for the purpose of reporting, to be located on another site (Site C) possibly in another domain. This server needs to have a replicated read only copy of the live database from site A or Site B, whichever is in use. The Site
C reporting database should be as up-to-date to the Site A or Site B database as possible – preferably within a few seconds anyway….
Solution - What I believe are available to me
I believe I can use AlwaysOn and create a ReadOnly replica for the Site C. If so do I assume Site C needs to have the Enterprise version of SQL server i.e. to match Site A & Site B?
Using log shipping which if I am correct means the Site C does not need to be an Enterprise version.
Any help on the best solution for this would be greatly appreciated.
Thanks, Steve

for always on - all nodes should be part of one windows cluster..if there site C is on different domain - I do not think it works.
Logshipping works --as long as the sql on site C is is same or higher version(sql 2012 or above). you can only do read only.
IMHo, if you can make site C in the same domain then, Always is better solution else log shipping
also, if your database has enterprise level features such as - partitonin, data compression -- you cannot restore the database on lower editions- so you need to have enterprise edition.
Hope it Helps!!

Best Solution for Archiving Table data

Hi All,
I have a table with huge data. It is not partitioned table.
On an average per day 10000 records will be inserted into this table. Now I want to archive(backup)
every one years data manually and keep in safe location and hence delete those archived rows
from the table. Whenever required it should be easily imported back to this table. All this happens through
Application.
One appraoch in my mind right now, is transferring the data from table to flat file with comma separted,
and whenever required again importing back to the table from Flat file using external tables concept.
Can any body suggest what is best solution for this.
Thanks

The best solution would be partitioning.
Any other solution requires DML - running DELETE and INSERT transactions to remove a data set and to add a data set (if need be) again.
With partitioning this is achieved (in sub-seconds) using DDL by exchanging a partition's contents with that of a table. Which means that after the archived data has been loaded (SQL*Loaded, Import, etc) into a table (and indexes created), that table (with indexes) is "swapped" into the partition table as a partition.

Is RMI best choice for this?

Hello!
I have some experience using the .NET Remoting with VB. I have understood that Java RMI is Java equivalent to .NET Remoting?
I'd like to serialize my objects and transfer them between the server and the client in internet.
I have red some opinions saying that RMI is good for intranet but does have major latency and scalability issues when it comes to internet.
Is the Java RMI best solution for this? What are the other techniques available with Java?
- Jarno Kiviaho

OK: You want to use RMI to connect an outside-the-firewall web server to a behind-the-firewall business logic server.
This is probably not too bad.
There are a couple ways that you can go.
1. Use RMI with HTTP tunnelling. I've never dealt with this, but you can probably find more about this searching this forum.
2. If you can get some ports opened for you in the firewall, then you can use the RMI transport and skip the HTTP stuff.
In the latter case, you
o Need to talk your firewall folks into opening two ports for you - one for a registry listener, the other for actual remote procedure calls.
o You need to make sure that your RMI server is designed to operate through one fixed port, rather than using random port numbers. Take a look back through this forum and again, you'll find people who have done this. (I did an implementation by providing my own SocketFactory, but I believe RMI has been improved since then so that the server can simply ask for the socket numer it wants.)

Need inputs from u for this scenario?

Hi all,
I have one scenario I need all inputs from u all.
My scenario is like this.
I will get data from online transactions I need to collect all the day transaction into one folder and upload them into SAP system at one particular time.
Which are the best adapters for this scenario.
If I have standard IDOC I will go with IDOC adapter at receiver side if not proxy.
But collecting all the data into one folder and schedule the process at particular time.
How to do this and what are the adapter I can use.
Thanks and Regards,
Phani Kumar.

Hi,
I hope for online transactions and for tracking it and saving you can write a java script where you can prepare a XML file to get all transactions for particular order and always append it to the end of that xml file. At end of the day you will have a complete transaction list in the XML you are creating. You can use the file name as you desired but i will prefer datewise name.after the completion of that Transaction recording step, put it in some In folder from where your XI system willo take input.
Now this is file to Idoc scenario or whatever you want to use to post data to SAP Systems. The sechdule this scenario to run in the night or your desired time. After processing the XML file put that file\ to some other complete folder , not to get it again.
For collection of transactions you can also use databases. Then you scenario will be JDBC to IDOC or the thing you want to post data in SAP system.
Hope this will help you.
Regards
Aashish Sinha
PS : reward pints if helpful

Migrated Aperture 3 upgrade from old Mac Book Pro to new Mac Book Pro. Can't open Aperture on new machine because I don't have the original serial number for Aperture 2 program originally installed on the old machine. What is the best solution to this s

Migrated Aperture 3 upgrade from old Mac Book Pro to new Mac Book Pro. Can't open Aperture on new machine because I don't have the original serial number for Aperture 2 program originally installed on the old machine. What is the best solution to this situation

Call Apple and make a appointment.
You have 3 months of care and up to 3 years with paid AppleCare, let them handle it and bring everything in.
Good Luck

RSV 400 best solution for this scenario?

Similar Messages

Maybe you are looking for