Run 10.6.2 and 10.5x at same time

I have run into several compatability problems with 10.6.2 ie., Roxio easy vhs to dvd and HP Scanjet G4050 scanner, and considered reverting to 10.5x but have read of the other problems doing this. I was wondering if it would be possible to run 10.5 either from my internal drive or my firewire 800 external drive using boot camp or VMWare Fusion 3 or Parallels Desktop 5 for Mac? I call Apple support a few weeks ago regarding a problem and the tech switched his machine to 10.5 to see if the problem I had was also in 10.5 and then he switched back to 10.6 while we talked. I did not ask about this at the time as I did not think about and had not had the Roxio or HP problems yet.
Any ideas regarding this would be appreciated.
Thank you

Install Mac OS X 10.5 normally onto a second partition or external drive, and then use the Startup DIsk pane of System Preferences or press the Option key at startup as desired. The client version of Mac OS X can't be run in emulation.
(49171)

Similar Messages

Is it possible to run both Netflow v5 and v9 at the same time

Hi All,
Just wondering if it is possible to run netflow version 9 and version 5 at the same time (to different destinations) on the same router please?
Thanks very much
Regards
Amanda

No Amanda,
we cannot simultaneously configure both versions of NETFLOW on cisco ios. After configuring firstone when you try to configure other version it will override the previously configured version.
"Please do rate helpful posts"

How can I run Macbook Pro screen and Thunderbolt display at same time with different programs?

I am running a Macbook Pro with Mavericks and using an Apple Thunderbolt display. I would like to run 2 different programs on the 2 screens at the same time. Is this possible?

Select Help from the Finder's Help menu and search for "mission control."
Mac Basics- Mission Control

WE HAVE A CLIENT COMPUTER IN THE SHOP (EXPANION UNIT). WE CAN'T RUN FIREFOX ON IT AND OFFICE COMPUTER AT SAME TIME. I HAVE CHECKED THE BOX THAT ALLOWS US TO RUN AS DIFFERENT USERS, BUT IT STILL IS NOT ALOWING ME TO LOG ON. SUGGESTIONS?

The box is under properties, 2nd tab, then advanced. We are currently using the same log on for both computers. Do we need to create a separate log on for the expanion unit or?

I would suggest trying it as different users.
'''If my reply solves your problem, please click "Solved It" next to this reply when signed-in to the forum.'''

Error Running Oracle Apps and Discoverer at the same time

Hello,
We are having trouble running Oracle Apps and Discoverer at the same time on certain user's machines. Here are the specifics:
The user opens Oracle Apps in Internet Explorer. The user then opens Discoverer in another Internet Explorer windows and receives the following error: Runtime Error! Program: C:\Program Files\Internet Explorer\iexplore.exe abnormal program termination
As a work around, I installed Firefox on those user's machines. These users run Oracle Apps in Internet Explorer and run Discoverer in FireFox. This has solved the problem in 99% of the cases. However, there is one user who is having FireFox using Discoverer freeze when running Oracle Apps in Internet Explorer.
Can anyone provide any insight on how I can solve these conflict issues so users can run Oracle Apps and Discoverer at the same time?
Thanks in advance for your help,
Carlos

Hi Michael,
I agree with you completely. It is reccommended to run 10g on a separate physical server unless you have sufficient resources to run on the same server (which even most large clients do not) Even then, I would recommend a separate server.
I should have put my comment in context :-)
a.) I was only stating that it was possible
and
b.) whether 10g is installed on the same physical server or separate should not affect the client browser crashing issue that was posted.
I do have an install with EBS11i and Discoverer 10g on the same physical server and it works fine (this is sandbox/ TEST). Most of my large customers have 10g installed on multiple physical servers due to load balancing (capacity).
I do work for Oracle. I try to help out on the forum when I can, but it is hit or miss :-(
I would be glad to discuss anything privately.
As for the issue at hand, I can reproduce the problem and here is what is occuring.
I have EBS 11i configured with Jiniator 1.3.24
I have Discoverer 10g configured with Sun Java plugin 1.4.2_06
1. If you launch EBS 11i apps and a form with MS IE, then the browser launches the form using Jiniator JRE 1.3.xx (whatever you have configured in AutoConfig for EBS11i)
2. Next, the user navigates to EBS 11i SSWA and launches a Discoverer workbook.
What occurs is a child IEXPLORE.exe process is spawned from the parent IEXPLORE.exe process and Discoveer Plus is launched. The parent iexplore.exe process will be attached to the Jiniator JVM. Now if Discoverer is configured with
a.) Sun Java Plugin or
b.)a version of Jinitiator that is a different version from what EBS 11i is configured with
then you may get this conflict.
It really is an MS IE/JRE conflict with Jinitiator and Sun Java Plugi and the way the broswers attaches to the JVM (IMHO) as this behaviour could be reproduced with other non-oracle java applets.
You can workaround the situation by:
a. configure EBS11i and Discoverer to use the same version of Jiniator 1.3.xx
b. educate the users to open one MS IE browser to connect to EBS11i and then open a second MS IE browser to login to EBS11i SSWA or Discoverer 10g Plus directly to launch workbooks. They need to to this by clicking on the icon and not using File >> New browser. Clicking on the icon will spawn a new parent iexplore.exe process that can attach to a second/different JVM. File >> New Window will spawan a child of the parent.
c. As you did use two browser versions. MS IE for EBS11 connection and FireFox for Disocverer 10g connection.
I would choose optoin b, so that you can use Sun Java Plugin with Discoverer.
Open to any comments. I hope that helps you workaround the problem. The ideal solution is to have EBS 11i use/cerified with the 1.4 or 1.5 JRE. In poking around, I see there is a related post to this on one of Oracle's EBS 11i Product Managers Blog.
See:
http://blogs.oracle.com/schan/2006/04/18#a23

Running Leopard and Tiger at the same time VMWare fusion/Parallels?

Hello,
I was wondering, is it possible to run Tiger and Leopard at the same time? Some older applications won't run properly in Leopard. The iMac came both with Tiger and Leopard (last November). It has been described elsewhere that one can install Tiger and Leopard on separate partitions and switch by rebooting. But it would be nice if one could run Tiger in Leopard like one can run Windows/Unix using VMWare Fusion or Parallels. Is that feasible?
best wishes

I agree with you that virtualizing Mac OS X would be great. I'm an Apple technician and it would really help with my work. But Apple's EULA does not permit the use of OS X in a VM. They changed OS X Server's EULA recently to permit it, but not the "client version".
So your Mac can virtualize nearly any OS out there, but not OS X. And I believe (not sure) that a VM of OS X Server will only run on OS X Server.

Since upgrading to Mavericks, I can't run Mail and Safari at the same time.

Since upgrading to Mavericks, I can't run Mail and Safari at the same time.
Either Mail will crash or the iMac will run so slowly as to be unusable. With both running, the HDD spins constantly at a high rate of speed.

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, look under User Diagnostic Reports for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents — again, the text, not a screenshot. In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.) Please don’t post shutdownStall, spin, or hang logs — they're very long and not helpful.

Running steps and sequences at the same time

Hi,
I need to run some steps and sequence at the same time in my application due to test time restrictions. I am using Teststand 2.0. Colud you please describe me the methodology.

Hi,
Synchronization Step types came in at version 2 and there should be an example in the \teststand\examples folder.
Regards
Ray Farmer
Regards
Ray Farmer

Running RIPv2 and OSPF at the same time

What are the problems with running RIPv2 and OSPF at the same time if any? I have the gear capable of that and I have been doing this for over a year now. I wanted to get rid of RIP but my couterpart is scared because he is not OSPF skilled. I do have some remote sites with old 1601s to consider. Any suggestions or recommendations.
Thanks

Hi Friend,
OSPF is far better than RIP when it comes to performance and advatnages compared to RIP and no doubt in that though it is complex to implement compared to RIP but once done it is smooth.
It is important to have a very well designed network with OSPF otherwise the behavior is unpredictable sometimes and it may not give desired results.
Also for your low capability routers like 1601s you can put them into stub or total stubby area so that they may have less load on them.
HTH
Ankur

Running Reports 6i and 9i at the same time

I was wondering what the issues were with running Reports 6i and 9i at the same time. We are planning on up grading at a client, and I heard that there are some problems with doing this. I was thinking that installing them in different ORACLE_HOME's would help keep problems to a minimum. At home I have Reports 6i and 9i running, and I have not seen any problems.

We suggest you install 6i and 9i at different oracle home. There are no known issue about running 6i and 9i at the same time.
Thanks,
-Shaun Lin

Why can't I run Safari and Skype at the same time without making my computer freeze up?

I can't believe I can't run Safari and Skype at the same time without my computer freezing up, it's a MacBook Pro with Mac OS 10.6.8 and it has an Intel Core 2 Duo CPU with 2.2 Ghz and 2 Gb of RAM. Is this a hardware problem or a software problem?

I haven't gone to the trouble of actually testing to see which uses more CPU power, but Firefox has been faster than Safari on every Mac I've ever owned.
To see CPU usage by process, open the terminal (in Utilities) and enter 'top' at the command line. You might have to expand the window as processes don't appear in any logical order.
It could also be hardware-related: I have late 2009 mini with similar specs and it pinwheels easily.

Recording Audio and Midi at the same time in Logic 7 Express Can it be done

I am wondering if I can record audio and midi at the same time in Logic 7 Express. I am running my guitar thrugh a Roland GR 33, and a line out and using the GR 33 to trigger sounds in the Logic's synth section but cant seem to record all three tracks at once. If any one knows how let me know. Oh and I am running the GR Synth and Guitar into the Prosonus Fire Fox and have the GR 33 out midi to the Fire Box as well. So I guss the question is how do I sent up two audo tracks and one midi track to record in real time. Thanks Victor

I am wondering if I can record audio and midi at the
same time in Logic 7 Express. I am running my guitar
thrugh a Roland GR 33, and a line out and using the
GR 33 to trigger sounds in the Logic's synth section
but cant seem to record all three tracks at once. If
any one knows how let me know. Oh and I am running
the GR Synth and Guitar into the Prosonus Fire Fox
and have the GR 33 out midi to the Fire Box as well.
So I guss the question is how do I sent up two audo
tracks and one midi track to record in real time.
Thanks Victor
Try arming the audio tracks, select one of the tracks, then while holding down the shift key, select the midi track you want to record, arming the "r" on the midi track. Press "record".....
HL

Can we use both INSERT and UPDATE at the same time in JDBC Receiver

Hi All,
I would like to know is it possible to use both INSERT and UPDATE at the same time in one interface because I have a requirement in which I have to perform both the task.
user send the file which contains both new and old record and I need to save those in MS SQL database.
If the record exist then use UPDATE otherwise use INSERT.
I looked on sdn but didn't find any blog which perform both the things at the same time.
Interface Requirement
FILE -
> PI -
> JDBC(INSERT & UPDATE)
I am thinking to use JDBC Lookup but not sure if it good to use for bulk record.
Can somebody please suggest me something or send me the link of any blog or anything to solve this problem.
Thanks,

Hi ,
          If I have understood properly the scenario properly,you are not performing insert and update together. As you posted
"If the record exist then use UPDATE otherwise use INSERT."
Thus you are performing either an insert or an update which depends on outcome of a search if the records already exist in database or not. Obviously to search the tables you need " select * from ... where ...." query. If your query returns some results you proceed with update since this means there are some old records already in database. If your query returns no rows you proceed with "insert into tablename....." since there are no old records present in database.
Now perhaps the best method to do the searching, taking a decision to insert or update, and finally insert or update operation is to be done by a stored procedure in MS SQL database. A stored procedure is a subroutine available to applications accessing a relational database system. Here the application is PI server.   If you need further help on how to write and call stored procedure in MS SQL you can look into these links
http://www.daniweb.com/web-development/databases/ms-sql/threads/146829
http://www.sqlteam.com/article/stored-procedures-parameters-inserts-and-updates
[ This part you can ignore, Since its not sure that you will face this situation
    Still you might face some problems while your scenario runs. Lets consider this scenario, after the stored procedure searches the database it found no rows. Thus you proceed with an insert operation. If your database table is being accessed by multiple applications (or users) other than yours then it is very well possible that after the search operation completed with a null result, an insert/update operation has been performed by some other application with the same primary key. Now when you are trying to insert another row with same primary key you get an error message like "duplicate entry not possible for same primary key value". Thus you need to be careful in this respect. MS SQL has a feature called "exclusive locks ". Look into these links for more details on the subject
http://msdn.microsoft.com/en-us/library/aa213039(v=sql.80).aspx
http://www.mssqlcity.com/Articles/Adm/SQL70Locks.htm
http://www.faqs.org/docs/ppbook/r27479.htm
http://msdn.microsoft.com/en-US/library/ms187373.aspx
http://msdn.microsoft.com/en-US/library/ms173763.aspx
http://msdn.microsoft.com/en-us/library/e7z8d5hf(v=vs.80).aspx
http://mssqlserver.wordpress.com/2006/11/08/locks-in-sql/
http://www.mollerus.net/tom/blog/2008/03/using_mssqls_nolock_for_faster_queries.html
    There must be other methods to avoid this problem. But the point is you need to be sure that all access to database for insert/update operations are isolated.
regards
Anupam

Run invoke-command on multiple machines at the same time

Hey all so I read that if I store my New-pssession in a variable then used that in my invoke-command it would run all computers at the same time.
$a = Get-Content "C:\Users\cody-horton\Desktop\list.txt"
$session
for($i=0;$i -lt $a.Length;$i++){
if(!(Test-Connection -Cn $a[$i] -BufferSize 16 -Count 1 -ea 0 -quiet)){
Write-Host $a[$i] -foregroundcolor red
else{
$session = New-PSSession $a[$i]
Invoke-Command -Session $session -FilePath "\\My computer\C`$\Users\public\Documents\zip folder.ps1"
What exactly am I doing wrong I just need to run this script on multiple machines at the same time.
Thanks.
Edit: Also what would be the best way to close all the sessions thanks.

Hi there,
So what I think you are doing wrong here is that you are overwriting the value in $Session everytime you executed code inside for loop. try the below:
$a = Get-Content "C:\Users\cody-horton\Desktop\list.txt"
$session = @() #define this as an array
for($i=0;$i -lt $a.Length;$i++){
if(!(Test-Connection -Cn $a[$i] -BufferSize 16 -Count 1 -ea 0 -quiet)){
Write-Host $a[$i] -foregroundcolor red
else{
$session += New-PSSession $a[$i] #add the new session to the array, at the end it will be a collection of sessions
Invoke-Command -Session $session -FilePath "\\My computer\C`$\Users\public\Documents\zip folder.ps1" #I think the above one won't work..first you need to copy the script locally on the machine and then execute it#Why this won't work because of Second-Hop Authentication
Have put comments where I edited your code.
Hope this helps
Knowledge is Power{Shell}. http://dexterposh.blogspot.com/

How can i run multiple instances of Photoshop EXE at the same time on windows 7

Alright. You may ask why do you need multiple ?
Assume that i have 10000 PSD files in 10 different folders
I have a script that just save as them as PNG
And these files are each 3000x3000 px
My computer has 8 cores and 1 photoshop exe is only using 1 cpu core
Also i have SSD raid system it has 750 mb read write per second
So right now i am wasting my time with running only 1 photoshop exe instead of at least 4

I'm not aware of a way to run multiple instances or different versions of photoshop at the same time on windows.
Assuming of course they are all installed on the same operating system.
On mac versions you can running two different versions of photoshop at the same time, but i don't think that's possible on windows where it
appears that only one version of photoshop can run at a time.

Run 10.6.2 and 10.5x at same time

Similar Messages

Maybe you are looking for