Run notepad as administrator if modifying cuda_supported_cards.txt after 6.03 update ...

Your mileage may vary ... When I originally installed CS6 on my new PC with a GTX 670 card I had to go edit the cuda_supported_cards.txt file and add the card; plus tweak the Nvidia settings (see link below).   Anyway, tonight after I installed the 6.03 patch update I had to modify the file again.  But I could not get notepad to save the file without an access denied error.   Even though I installed the original program and patch update under my user name with administrator priveleges, I had to go back and run notepad as administrator.   Just an FYI post in case someone runs into this issue.
http://vimeo.com/13440307

You don't need to edit the file to recognize your card, simply delete the file and hardware MPE will be enabled! That's much easier.
Jim

Similar Messages

  • Apple tv3 runs slowly on all apps in the box,after the last update.Picture sometimes runs slowly on netflix ,and all the apps in the apple tv3 box.But the sound is ok.Anyone else have this problem?

    Apple tv3 runs slowly on all apps in the box,after the last update.Picture sometimes run's slowly on netflix ,and all the apps in the apple tv3 box.But the sound is ok.Anyone else have this problem?I have a 20Mbit wireless line,but i had put a cable from my router to my apple box,but it did not help.

    Are you using a home network?
    Try the following :                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings

  • While installing the latest iTunes version I get the following msg:"Service Apple Mobile Device failed to start.Verify that you have sufficient privileges to start system services. I already tried it from the installer Running it as Administrator

    While installing the latest iTunes version I get the following msg:"Service Apple Mobile Device failed to start.Verify that you have sufficient privileges to start system services. I already tried it from the installer Running it as Administrator and still get the same message.  I click "ignore" and finish the installation but when I try to open it I get this "Runtime Error! R6034 An application has made an attempt to load the C runtime library incorrectly."  I already uninstalled iTunes and all other applications involved and re-installed itunes from the itunes site and the problem persists. Please help!

    Solving MSVCR80 issue and Windows iTunes install issues.

  • Firefox will not open unless I run it in compatibility mode (Windows XP SP 3), run it as an administrator, or launch it immediately after a reinstall (the reinstall thing only works once.) How do I fix this?

    This morning, Firefox crashed. After this, when I click the Firefox icon, the hourglass appears and then nothing happens. Firefox does briefly appear in the task manager when I do this.
    I tried rebooting. I tried reinstalling multiple times. (Firefox will run when I select "Launch Firefox" from the installer. Then the problem occurs again.) I tried safe mode. I have found that Firefox will work if I select Windows XP compatibility mode from the icon properties menu or if I run the program as an administrator. When I do this, Windows asks me if I want a program to be able to make changes to my computer.
    I have noticed that a Windows Error Report is being generated each time Firefox will not open.

    A possible cause is security software (firewall,anti-virus) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox and the plugin-container from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
    See:
    *https://support.mozilla.org/kb/Server+not+found
    *https://support.mozilla.org/kb/Firewalls

  • Dear All, I can't play flash videos from any web site through firefox because it freezes but when i run firefox as administrator then it works fine (But Google Chrome Plays all videos normally.) . I am using Windows 7 & Firefox 7.0.1. Please help

    Dear All,
    Firefox hangs when i try to play flash videos from any site but when i run firefox as administrator it works fine. (but Google Chrome, Opera & I.E9 Plays videos without running as administrator.) I am using Windows 7 & Firefox 7.0.1. Please help.

    A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
    See:
    *https://support.mozilla.com/kb/Server+not+found
    *https://support.mozilla.com/kb/Firewalls

  • Cuda_supported_cards.txt no longer present in CC 2014 Premiere Pro, After Effects Folders

    I'm on a "gaming" Win laptop using one of the latest nVidia GPU's, the GTX 880M. Being new--year old really new?--, I had to add it to the list contained in cuda_supported_cards.txt for Pr, AE and AME. With the newest CC 2014 update, these .txt files are no longer present in their respective program folders.
    Does this mean that the programs no longer differentiate? If they see CUDA cores they enable the acceleration? Or does this mean they stopped the end-user from by-passing their filters? How to verify if I'm getting the acceleration? I recall having the feature greyed out in previous versions of these programs if I hadn't yet edited the list, and at the moment they are not greyed out despite not having found a list to edit.
    I've searched for mention of this change in newest version but have yet found a discussion.
    Thanks in advance,
    Andrew

    From CC 2014 menu, select: file / project settings / General
    And if the Renderer "drag down" shows a "Mercury Playback Engine GPU Acceleration" option, then rest assured that Premiere Pro is seeing and using your GPU!
    Regards,
    Jim

  • Running iTunes as Administrator fixed "iTunes has stopped working" error.

    I have this problem with iTunes.  Whenever I try to access the iTunes store, I get the Windows "iTunes has stopped working and needs to close" error.  I am running Windows 8 64-bit.
    If I run iTunes as Administrator by right clicking the iTunes icon and clicking "run as Administrator" I no longer experience the issue.
    I'm running the latest iTunes version as of 10/11/2013.

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    tt2

  • How to check which administrator had modified the AD Group properties

    Dear Sir,
    Some one had modified a Distribution group (removed email address). I checked it in group properties and last modified was on 22/09/14. How to find which administrator had modified.
    I dont have access to domain controller. Is there any way to find it?
    thanks in advance.
    Karan

    Hello,
    this will be logged on DCs and also auditing must be configured correct that this will show up in the event viewer from a DC.
    Without access to the DC contact your administrators and let them find out.
    Best regards
    Meinolf Weber
    MVP, MCP, MCTS
    Microsoft MVP - Directory Services
    My Blog: http://blogs.msmvps.com/MWeber
    Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
    Twitter:  

  • Queries run faster under Administrator account than from "regular" users

    We have OBIEE 10g used as a reporting tool against E-Business R11i. When OBI reports are run from the Administrator account, they complete in about 15 secs. When the same report , with same parameters is run from a non-administrator account, completion takes 5 mins. In this latter case, the E-Business DBA can clearly see the "expensive" query running in the E-Business database (module=nqsserver@<obi application server host>). In both cases, the results of the query are the same.
    What can account for the difference in performance when the user account is changed?
    TIA

    Hi SVS,
    Not too sure what you mean but I do know that,
    1. Authentication for end-users is through MS Active Directory (to login to OBI, they enter the same password as for the Windows Domain login to their PC's).
    2. Authorization is via responsibilities granted to their corresponding accounts in R11i E-Business Suite, ie the reports that they can run in OBIEE are determined by responsibilities in E-Business.
    Thanks,

  • How can IT departments set up basic users to run Captivate with Administrator privileges?

    As we all know, on WinVista and Win7 or later systems Adobe Captivate must be launched with Run As Administrator privileges in order to function correctly and not crash.  But the problem here is that in many corporate environments general users are not allowed to have Administrator access to their own work PCs.  This presents something of a dilemma for IT departments with Adobe Captivate users.
    Some time ago on this forum one of the Adobe technical staff chimed in on a thread about the Run As Administrator command and explained the technical steps required to set up a Group Policy in WinVista/Win7 that would allow a basic user to always launch Captivate with the necessary admin privileges even though they did NOT have Administrator access to any other app on their PC. 
    I have searched in vain to find that particular thread and post, so I've started this thread in the hope that someone at Adobe can again chime in to detail the necessary steps again.
    So is there anyone there that can help out?

    DOH! my bad.....I/we run WinXP at present and no UAC.
    However, all may not be lost, try some of these options as posted on teh MS Technet forums....An admin person may need t do this first to enable this for that user...
    Apologies for misundeerstand situation. ;-( hate it when that happens!
    Try these two options:
    Using Compatibility Mode
    NOTE: This will allow you to always have the program run as an administrator when you open it.
    1. Right click on the program shortcut or program .exe file, then click on Properties, and on the Compatibility tab. (See screenshots below)
    NOTE: If you are doing this while logged on as a standard user instead of an administrator, then you will need to also click on the Change settings for all users button and type in the administrator's password.
    http://www.sevenforums.com/attachments/tutorials/12832d1243933304-run-administrator-compat ibility_mode1.jpghttp://www.sevenforums.com/attachments/tutorials/12832d1243933304-run-administrator-compat ibility_mode1.jpghttp://www.sevenforums.com/attachments/tutorials/12832d1243933304-run-administrator-compat ibility_mode1.jpgUAC, then click on Yes to apply permission to allow the program to run with full permission as an administrator.
    2. To Always Run this Program as an Administrator
    A) Check the Run this program as an administrator box, and click on OK. (See screenshots above)
    3. To Not Always Run this Program as an Administrator
    A) Uncheck the Run this program as an administrator box, and click on OK. (See screenshots below step 1)
    4. Open the program.
    5. If prompted by
    NOTE: If you are doing this is while logged in as standard user instead of an administrator, then you will need to provide the administrator's password before the program will run as administrator.
    Using Advanced Properties
    NOTE: This will allow you to always have the program run as an administrator when you open it.
    1. Right click on the shortcut of the program, then click on Properties.
    2. Click on the Shortcut tab for a program shortcut, then cllick on the Advanced button. (See screenshot below)
    http://www.sevenforums.com/attachments/tutorials/12834d1243933304-run-administrator-advanc ed_properties1a.jpghttp://www.sevenforums.com/attachments/tutorials/12834d1243933304-run-administrator-advanc ed_properties1a.jpghttp://www.sevenforums.com/attachments/tutorials/12834d1243933304-run-administrator-advanc ed_properties1a.jpghttp://www.sevenforums.com/attachments/tutorials/12836d1243933304-run-administrator-advanc ed_properties2.jpghttp://www.sevenforums.com/attachments/tutorials/12836d1243933304-run-administrator-advanc ed_properties2.jpghttp://www.sevenforums.com/attachments/tutorials/12836d1243933304-run-administrator-advanc ed_properties2.jpgUAC, then click on Yes to apply permission to allow the program to run with full permission as an Administrator.
    3. To Always Run this Program as an Administrator
    A) Check the Run as administrator box, and click on OK. (See screenshot below)
    4. To Not Always Run this Program as an Administrator
    A) Uncheck the Run as administrator box, and click on OK. (See screenshot above)
    5. Click on OK. (See screenshot below step 2)
    6. Open the program.
    7. If prompted by
    NOTE: If you are doing this is while logged in as standard user instead of an administrator, then you will need to provide the administrator's password before the program will run as administrator

  • How to run notepad from a web application

    hi
    can any body know,how to run notepad from a web application under tomcat

    You already asked this question:
    http://forum.java.sun.com/thread.jspa?threadID=5150005&messageID=9561597
    Obviously running notepad on the clients PC is not possible (ignoring active x)

  • When I try to launch terminal, i get an error "You are not authorized to run this applicationThe administrator has set your shell to an illegal value."

    When I try to launch terminal, i get an error "You are not authorized to run this applicationThe administrator has set your shell to an illegal value."

    If you'd asked a question in your original post it might have solicited more pertinent responses. As it is, you were stating a fact. No one knew whether you considered that fact a problem, or what you were hoping to gain by doing so.
    The simple addition of 'can anyone help me fix this so I can run Terminal' would have counted for a lot.
    As it is, your solution is likely to require the Terminal, so you're going to need to fix that one way or another. The simplest would be to create a new admin account (System Preferences -> Users & Groups) then log in using that account.
    Then try and launch the terminal. If that works the problem is specific to your original account and can likely be fixed via some command-line tweaking. I'd start with:
    dscl . read /Users/<username>
    (where <username> is the short name of the account having a problem). This will show the records in the directory data for your account, one of which will be UserShell. Chances are that value is invalid, or missing, and can be corrected via:
    sudo dscl . -change /Users/<username> UserShell <currentValue> /bin/bash
    (where <currentValue) is the current setting for UserShell) which will change the user's shell to /bin/bash (the default).
    Of course, you might already know this and already tried, but since you didn't say so in your original post it's worth checking.

  • Various features in this run of AD Administration

    Dear All,
    I am new to Oracle EBS and working on R12.
    While running adadmin i observed it is displaying the status of various features of AD Administration.
    The status of various features in this run of AD Administration is:
                                               <-Feature version in->
    Feature                          Active?   APPLTOP    Data model    Flags
    CHECKFILE                        Yes       1          1             Y N N Y N Y
    PREREQ                           Yes       6          6             Y N N Y N Y
    CONCURRENT_SESSIONS              No        2          2             Y Y N Y Y N
    PATCH_TIMING                     Yes       2          2             Y N N Y N Y
    PATCH_HIST_IN_DB                 Yes       6          6             Y N N Y N Y
    SCHEMA_SWAP                      Yes       1          1             Y N N Y Y Y
    JAVA_WORKER                      Yes       1          1             Y N N Y N Y
    CODELEVEL                        Yes       1          1             Y N N Y N YPlease explain about the data model, and each flag stand for ?
    Thanks,
    Kods

    KODS wrote:
    Dear All,
    I am new to Oracle EBS and working on R12.
    While running adadmin i observed it is displaying the status of various features of AD Administration.
    The status of various features in this run of AD Administration is:
    <-Feature version in->
    Feature                          Active?   APPLTOP    Data model    Flags
    CHECKFILE                        Yes       1          1             Y N N Y N Y
    PREREQ                           Yes       6          6             Y N N Y N Y
    CONCURRENT_SESSIONS              No        2          2             Y Y N Y Y N
    PATCH_TIMING                     Yes       2          2             Y N N Y N Y
    PATCH_HIST_IN_DB                 Yes       6          6             Y N N Y N Y
    SCHEMA_SWAP                      Yes       1          1             Y N N Y Y Y
    JAVA_WORKER                      Yes       1          1             Y N N Y N Y
    CODELEVEL                        Yes       1          1             Y N N Y N YPlease explain about the data model, and each flag stand for ?
    Thanks,
    KodsPlease see (Oracle E-Business Suite Patching FAQ for Release 11i and Release 12 [ID 1325930.1]) -- "What is the AD Features matrix displayed on the AutoPatch screen and in the logfiles?" section.
    Thanks,
    Hussein

  • I can not run the account Administrator show me this letter Please help :

    I can not run the account Administrator show me this letter Please help
    http://im40.gulfup.com/4AXHK.png

    Hi,
    You need the administrator permission to enable the built-in administrator account.
     For secure concern, there is no other way to do this.
    Alex Zhao
    TechNet Community Support

  • Running Firefox without Administrator Permissions

    I am an enterprise administrator and want my users to be able to run Firefox on their Windows 7 desktops. I have installed using elevated permissions but when the users try to open the application without admin permissions (they are members of the Remote Desktop Users group) it just presents a dialog box that says "Firefox has stopped working." Any suggestions?

    Check that you do not run Firefox as Administrator.
    Right-click the Firefox desktop shortcut and choose "Properties".
    Make sure that all items are deselected in the "Compatibility" tab of the Properties window.
    * Privilege Level: "Run this program as Administrator" should not be selected
    * "Run this program in compatibility mode for:" should not be selected
    Also check the Properties of the firefox.exe program in the Firefox program folder (C:\Program Files\Mozilla Firefox\).

Maybe you are looking for