Run SATA and EIDE HDs (P7N SLI Platinum)

What would be the BIOS setup and cableing to run an EIDE drive as D: when the primary boot drive (C:) is a SATA? [P7N SLI Platinum].
BTW: from an earlier post, new computer up and running- I cloned my EIDE HD on old system to new SATA HD. Installed SATA HD into new system, booted XP CD and ran the Repair (the later one). Booted into Safe-Mode and loaded nVidi Ethernet Drivers, rebooted, reactivate and all is working.

Drive letters are not assigned by BIOS or hardware, but by the operating system. If you install the operating system on the SATA Drive, it should automatically become drive C:. If you want to make that automatism faik-safe, simply unplug the IDE Drive when you are installing the operating system on the SATA Hard Drive,

Similar Messages

MSI P7N SLI Platinum and OCZ DDR2 PC2-6400 SLI-Ready Edition

Hello,
I have a MSI P7N SLI Platinum nForce 750i SLI motherboard and I would like to inquire if it is fully compatible with OCZ DDR2 PC2-6400 SLI-Ready Edition memory? Firstly, I do not seem to get the correct timings with the default settings, speed is not very good, after 5 hours of running Memtest86+ there was 30 errors. I have never had the memory crash and games seem to run fine, but the memory feels much slower than it should be. Is the memory supposed to work fine with this motherboard and I'm just imagining everything? I don't know if I'm also supposed to be worried by the errors Memtest86+ returned?
Thank you in advance for any help.

Quote from: Del UK on 07-September-08, 05:44:14
If memtest returned errors, yes
Well, there does not have to be a problem with the memory just because it returned errors. There could be many other explanations why there are errors.
Quote from: Jack the Newbie on 07-September-08, 08:04:45
Jacobl, please post full system specs. Read the >>Posting Guide<< to get an idea of the details you should provide.
How many modules of what capacity do you have? What are your current RAM-related BIOS settings?
If you have more than one stick of RAM, please test each stick seperately with memtest86+ and see if the errors are caused by one of the sticks only. Otherwise there is no way to tell if there is a compatibility problem or just a faulty memory stick.
Please post a link to the OCZ product site and also a screenshot of the CPU-Z "SPD" tab.
I have this memory: http://www.ocztechnology.com/products/memory/ocz_ddr2_pc2_6400_sli_ready_edition_4gb_dual_channel.
This is the rest of the components as instructed by the forum post you linked to:
Intel E8200
MSI P7N SLI Platinum
OCZ DDR2 PC2-6400 SLI-Ready Edition 4GB Dual Channel
Gigabyte Geforce 8800GT 512MB PCI
500GB Western Digital SATA
SATA DVD burner
Windows XP SP3
Antec 500W PSU
I usually troubleshoot components step by step - eliminating all possible reasons until I have found the solution. My first step was to post here to find out if there are any known compatibility issues with the motherboard and memory. I adjusted the memory timings with a slight overclock because the motherboard did not load the default timings by default. I will start by adjusting the BIOS settings, check if the memory is inserted into the right DIMM slots and then test the memory sticks one by one. But to answer my own question: I think the motherboard and memory should have no compatibility issues and it must be something else.
Quote from: Freestate on 07-September-08, 23:06:36
I have the OCZ 6400 Fatal1ty modules 2x2 GB that is very similar of the ones you ask.And they are running perfectly but i must set the epp latency and voltaje values in BIOS! The simple modules of ocz are in the memory compatibilty list i thought that the SLI and Falal1ty modules are just the same with a little boost.
I had to set the right timings also. As far as I know, the SLI and Fatal1ty modules are probably the same, just with a little boost. I think it would be very strange if a module with the name "SLI-Ready Edition" and a Nforce 750i motherboard would not be compatible together.
Anyway, any other advice on what steps I should take? I assume by now that the motherboard and memory should work together without problem. Sorry if I started out bad by not following the posting guidelines on the forum.

P7N SLI Platinum Unstable with over 2GB ram and/or dual channel memory on.

Hello need some help or to report something to MSI regarding blue screens, freezes when booting Vista 64 (SP1 + all fixes installed) with more then 2GB ram. Single channel mode works (either 1 stick of 2 GB or 3 sticks of 2GB) and is rock stable. Booting with 2 x 2 or 4 x 2 yields instability and blue screens.
I read over Microsoft's hotfix KB929777 however it appears this patch was applied during SP1. http://support.microsoft.com/kb/929777 - when I attempted to apply this hotfix I got the message this update does not apply to your system.
Memory tested in other gaming system using 4 sticks of G.Skill 1066 DDR2 ram and still have the same issues. Other forums like Evga.com, Tom's hardware and 411overkill.com tend to suggest some problem with this new bios version 2.0, written by Nvidia. Some others mention possibly an Nvidia nforce driver issue.
Therefore, under duress during testing - with 1 stick or 3 sticks of ram, all tests perfect and passes all stability tests, good marks in Sandra, plays any game. With 2 or 4 sticks of ram, very unstable won't stay up but for seconds.
Any ideas? (Tested 7 ways until Sunday!)
My other rig, rocks solid and stable with Vista 64.... It's the Evga new mainboard 780i with triple SLI (132-CK-NF78-A1), 8gb of Gskill 1066ddr2, MSI 8800GT (x2 sli mode) Q6600 @ 3.2 ghz - Raid 0 on dual WD caviar 640 gb/sata 3.0gb/sec. Seasonic 700w p/s. 8gb of memory and not a hiccup. Ram 2.0 volts, cpu @ 1.36v. Will handle the memory from both systems with out fault.
Considering I can swap memory back and forth and confirm it's not the sticks, swap graphics boards (own 3 of them!) and rule out that....
Fyi. Any help is appreciated!

Dump question, but have you pickup the correct update e.g. for 64bit? ==> http://www.microsoft.com/downloads/details.aspx?FamilyId=91672C7C-614B-404C-850C-377541E93C18&displaylang=en
"This comes inside SP1 for vista 64, as noted with my other system during the build. "
Better double check it.
Install all four memory sticks and do a memory check with >>Memtest86<< 1st, ensure that no error(s) will comes during testing.
Also how about that?:
Quote from: BOSSKILLER on 07-April-08, 23:55:36
Remove your OC then see how its goes.
"When the system boots in single channel mode (only 2 or 6gb of ram meaning 1 or 3 sticks installed into the 4 slots) its' rock stable. When it boots into dual channel mode (2 x 2 sticks or 2 x 4 sticks) extemely unstable. "
That means, timings are too tight, or they need a bit more vcore help, or some of the memory stick has failure.
"MSI P7N SLI Platinum - MS-7380 - Bios 2.0 on Vista Ultimate 64-bit - all updated."
That BIOS is not for your board, you should use 1.xx

P7N SLI Platinum and power consumption?

In few day I'll get a Msi P7N SLI platinum to replace my Gigabyte P35,I would like to know the power consumption for 750i? Is lower than 780i?
You can see in the picture the 780i 48W and P35 only 16W So big different!!!

A quick Google search pulled this article. Not sure if it helps you any, but here you go...
http://hothardware.com/Articles/NVIDIA_nForce_780i_SLI_Arrives/?page=11

New P7N SLI Platinum Boot Issue with PS/2 Keyboard [Solved but RAID problem now]

This issue taken me back !!!! Never thought I might face issue with a PS/2 Keyboard.
Here it is.. I just assembled my new system...
P7N SLI Platinum Motherboard
E8400 CPU
EVGA 256-P2-N751-TR GeForce 8600 GT Video Card
Creative Soundblaster Audio Card
So, before I boot, I connected good old PS/2 Keyboard. The POST Screen comes up that says Press DEL to enter BIOS Setup... but then, it reboots.. indefinitely... I have no idea why it does that. However, if I boot the PC with no PS/2 Keyboard connected, POST screen comes up and that's it.. (no reboot). So, you see, I cannot proceed further in anyway.... I cannot go beyond POST without a keyboard, but then with the keyboard it reboots indefinitely... kinda catch 22 situation
Any suggestion / ideas that anyone can offer here???

Hello Folks... it took long time to "solve the issue that had to begin with"....
I purchased a cheapo Celeron processor to get into the BIOS and update it... but it didn't even work... I couldn't boot at all. So, I called MSI and they asked me to RMA it. They replaced my MOBO with the latest BIOS - which was good news
So, now, I'm able to boot - good news...
Now, this is an upgrade for me.... from my previous MOBO. My boot drive was RAIDed (RAID 0). So, now, I will have to RAID my drives again and run Win XP repair. I was able to RAID my drives and all good... now, I went into Windows installation and did F6 to install NVIDIA Raid.... but, here is my problem, when the prompt asks me to input the floppy drive, and when I did it.... it re-prompts me to put the floppy drive again... I see that the floppy drive is read... but, for some reason it doesn't detect the files in there properly.... I downloaded nVidia C72+MCP55 SATA RAID / AHCI Driver (For floppy driver) for windows xp 32-bit and copied the sataraid folder contents into the floppy. Now, here I am stuck again....
Anybody experienced this problem?

MSI P7N SLI Platinum Freezes using USB Device

Whenever I insert my Sony K810i Mobile USB Data Cable into a USB Socket on my P7N Motherboard and select File Transfer
To access my Mobile, the Computer freezes ???
I have to reboot the system to get control of the Computer..
Any known USB problems with this board..
My Sony K810i worked fine with my old AMD K9N SLI Platinum Motherboard, no problems..
Any ideas to fix this ?
(USB Mouse works fine..)
Specs:
Mobo: MSI P7N SLI Platinum
CPU:Quad Q6600 - Alpine H/s (Temps at idel 17c)
Graphics: 2x MSI 8800GT running in SLI
Memory:4x2GB Patriot DDR2 6400 800mhz
HDD 2x Sata Drives
O/s Vista 32bit
DVDWriter:LG

Located the problem, turned out to be a missing driver from Sony
All the USB ports work fine...
This post is now closed..

MOVED: P7N SLI Platinum Mobo Memory overclock

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=121549.0

Quote from: kourosh on 19-November-08, 15:23:58
that is even better for an air cool, by the way did you increase the memory freq manually or it was increased as you increased fsb?? ??? cheers
Once again a slight manual tweak on the FSB and Memory settings and I can now getting it stable running at 3.66Ghz (Air Cooled)
Temps 37c idle to 46c running UT3 (running for about an hour)
I'm running the Memory Voltage at 2.10v, everything is stable no problems, no crashes or BSOD,
The OCZ SLI Edition Memoryboards seems to handling it well..
Memory is clocked at 966Mhz, this seems to be the highest I can take it, any higher and Quake3 Demo locks and it says driver fault..
This seems to be the most stable overclocking setting I can reach so far..
Maybe a increase on the CPU or FSB,NB voltages might gain me a few more higher freq settings..
BIOS Settings
And from 764fps on Q3 Demo Test at 1280x1024 running at 3.54Ghz
To 796.9 fps at the same Screen Res running at 3.66Ghz
Regards
NC....
Windows Vista 64 Ultimate
Motherboard - MSI P7N SLI Platinum
CPU - Core2Duo E8500 + Cooler - Arctic Pro 7
Graphics - 2 X MSI 8800GT (SLI)
Memory - 2 x 4Gb DDR 2 PC6400 OCZ SLI Edition
Antec Nine Hundred Case [4 Fans]
LG x22 DVD Writer (Lightscribe) SATA
2 x Samsung Spinpoint SATA Hard Drives 100Gb/250GB
PSU - Cosair 650w TX
Fav Game - Call of Duty 4 (yeah bring it on and kick my ass if you see me on there)

Help with ram slots on MSI P7N SLI PLATINUM

rig config:
MSI P7N SLI PLATINUM (MS-7380)
bios version: 1.3v
Q6600 quard core 2.66GHz
Zotac modded 9800GTX+ amped version
2x2 Gb DDR2 800MHz Kingston
500 watt (absolute) power supply (taken form an old HP workstation)
windows 7 X64
Everything's on stock setting
Its been almost 1 & 1/2 years since i bought this rig, and from first month itself i have been having problem with the ram. The problem is not with the sticks, its with the ram slots. There are different things that happen. Sometimes when i boot my system:
1) either, it wont start, i.e. no boot screen.
2) It will load upto windows startup screen, crash and restart in an infinite loop.
3) It will load windows, then crash after sometime.
4) If i run any memory diagnostic, it will give errors.
At these times, i take out my 2 ram sticks, tinker with them, place them in different combination of ram slots, try push them in, in a certain way, keep trying until it yields and it boots up again ( generally a process of 1/2 an hr to an hr). After this my system will work fine ( no errors on any memory diagnostic) and boot properly for a week or 2, maybe even a month, but then again the same problem happens. I know for sure that there is no problem with my dimms (have checked them in other system and they work fine), its something to do with ram slots, or memory bus-controller structure.
Recently the problem happened again, though my tinkering didn't help. My system only boots up if i place any of the ram sticks in the 3rd slot (the 1st orange one). It wont work for any other slot and neither will it work if i place both of the sticks together. I have tried resetting my bios as well cmos settings, but it has not helped. My mb is still in warranty, but if i give it for repair, it will be gone for a good month or so, which doesn't go well with me. If someone has any suggestions, or a way out, it will be highly appreciated. Please help!

Quote from: nellinil on 10-July-10, 10:27:51
yes the psu has a single +12v rail with 21A rating, but somehow i don't feel the problem is because of it. When my system successfully boots, it works properly. I can play or work on high performance softwares for any number of hours without fail, which ought not to happen if the psu is bad.
Hmm, you are ignoring the possibility that your PSU is "flaky" (that's a technical term)!!!! You've never had any gizmo where "sometimes it works and sometimes it doesn't work"?
If you don't want to buy a new PSU then at least beg-borrow-steal another one and see if your symptoms change.

Having a hard time OC'ing my Q6600 on the P7N SLI platinum!!

Well, first of all, I am new here, so hello to you all guys!
I just purchased the p7n yesterday. I had a P6N SLi-V2 before and wasn't able to get over the 3.0 GHz (stable)! I thought the P7N will a much better overclocker but find myself having a really hard time get it over 3.0 GHz again!?
Tried different versions of the bios (1.0,1.1,P04 and now 2.0) with no succes! Maybe anyone can help me out here and maybe share some bios setup? Will really appreciate it
My rig:
Q6600 C2Q G0-stepping
Tuniq Tower 120 CPU cooler
P7N SLI Platinum
1 x 2 GB TakeMS PC6400 DDR2 RAM
2 x MSI NX8800GT OC 512MB
1 x 200 GB + 1 x 250 GB HD
Cooler Master Extreme Power 650w

Quote from: troopertroop on 20-April-08, 22:22:09
Man, this turns out to be like a disaster :S:S I tried everything and now it won't even be stable @ 3.0 GHz with vcore 1.35, vram 2.2, fsb vtt 1.45, nb 1.4 and SB 1.5 (random reboots like crazy!). I have the intention to get some better OC's going from a p6n sli v2 to this board and it's even doing WORSE??????? The only weakpoint I can think about is my single stick 2GB TakeMS pc6400, but I never go over the stock speed of 800 MHz, so can that still be a bottleneck even at stock speed or even lower?
Any help will be welcome...
I found out the hard way.........if you are not running memory from the QVL list with this mobo, you will have problems with it. I was running mine with team xtreem 3-3-3-8 microns and all I had was errors and corruption when I overclocked. I had to reformat and switch back to the performance bios and now running corsair dominators 3-4-3-9 and this is the first set that can run at 1200 mhz at 5-5-5-18 2T 2.2 v with the fsb at 1600. I 'm using an E8400. I have read that using non approved memory and this board will not overclock properly. The only non approved memory that works in my system is geil ultra 8000's and these are the originals running D9GCT's. For stability you should try OCZ, Corsair, Mushkin, Buffalo, Kingston. I have also had problems with crucial ballistix as I've found most of there modules are in someway defective and or not compatible with MSI and have rma multiple sets. I have a previous post going from P6N FI to P7N and have listed all the memory that I have tried on this board. OCZ and corsair work the best and geil can be used but will not oc past 1142 mhz with stability. I think after a few bios updates this board will be able to use more different types of memory without stability issues.

Problem with my p7n sli platinum

Hello,
i just bought the P7N SLI Platinum for my new system and use an old ATI X1800XT as my gpu.
after finished installing all the hardware,then i tried to install a fesh copy of windows xp...
the problem is, every time my computer tried to login into the windows.. a blue screen will appear..
i suspect the problem is due to the x1800xt..therefore i tried to use it with my old intel motherboard but it can login into windows perfectly well..
does anyone know what the cause of this problem? is it because i'm using ati card with nvidia chipset?
please everyone help me!!

Quote from: BOSSKILLER on 23-November-08, 21:04:26
STOP: 0x0000001E
* There is insufficient disk space on the drive on which you installed Windows.
* There is an outdated or incompatible third-party driver (or drivers) installed on your computer -- for example a faulty video driver.
* There are system BIOS incompatibilities.
Finally, my system is now working perfectly but I'm still not sure what is the cause for all of this madness.
I didn't change any of the hardware or the drivers.
I don't think this is because of the insufficient disk space because after many series of failure with this board, I have tried to install a fresh windows copy using the same hard drive with my previous motherboard and everything seems to be running smoothly...it could finish the installation process..and safely loading into windows...
Then when I tried with this board again, still no improvement at all...i tried again..again...and again...until i was frustrated enough to made some random changes in the bios settings and FINALLY...it works!!..
I have no idea what were the changes that I've made in the bios...maybe it was just my luck....but I do notice the change in my cpu vcore..before this, it was running at 3.0GHz with default vcore of 1.080v...but now, the default vcore has suddenly changed to 1.250v with the same frequency of 3.0Ghz...and I couldn't find any way to return the voltage back as before..is this normal? I thought E8400 with E0 stepping should have lower vcore...isn't it?

RAID 0 on my board (P7N SLI Platinum)

Hi guys, I'm gonna be honest and admit I'm a beginner when it comes to these kinds of things.
Now thats out of the way, I've got two drives of the same size, revision and manufacturer, so I wanted to set them up in RAID 0 for faster load times and such. Though I don't have any idea where to start with this..
I have Vista 64bit Home Premium,
MSI P7N SLI Platinum
Q6600
8800GT SLI
2x 500gb SATA Seagate Barracuda 7200.11
4gb of RAM
I was wondering if it would be possible for someone to give me a simple, easy to follow step-by-step process for setting up a RAID 0 system. I need help with the BIOS settings, the drivers and where to get them, and anything else (intel matrix if needed??)
The manual doesn't mention how to do it, well..if it does I dont understand it, also I couldn't find any help on google so I thought I would come to a place where people will know about these things.
It's going to be for gaming and general windows use so I want to it to be as performance orientated as possible - I daren't try myself as I don't have the ability to fix it if I really mess it up I will seriously appreciate it if you can help me!
Thanks

here is how I did it:
enter the bois by pressing del, then go to integrated peripherals then to on-chip ata devices. You will see there a setting called raid mode it is set to ide change that to raid mode. Now enable sata1 and sata 2 oh make sure u drives is on sata1 & 2 . now save and exit. As the pc boot up there will a option to press f10 to create the raid. once in the utility change the mode from mirror to stripping(raid 0) , at the bottom of the screen you will see 2 boxes one on the left hand side will have your drives in it now move to the drive with the arrow keys and move both to the right hand side once there press ctrl+x to create the raid or read at the bottom of the screen for the options.
Once your is created load vista normally and then when it asks to what drive u want to install it will be blank remove the vista cd and insert your driver cd for vista. Now click on load then browser then navigate to E:\ChipSet\Nvidia\Vista64\C72+MCP55\IDE\WinVista64\sataraid and click ok a list of driver will appear select all and click next. After this u will be taken back to the screen where you will now see your hard drive click on it and install vista like normal
Hope this was help full as i do it this way

MSI P7N SLI Platinum CPU Power Socket

I have a MSI P7N SLI Platinum and I just noticed I dont have a 8pin power plug on my ATX PSU ( this PSU is in my AMD rig)
I've just had a go of trying out my MSI P7N SLI Platinum board as a computer shop said just insert the 4 pin plug you used on your AMD board near the CPU..
I questioned him about it leaving 4 sockets bare, he said it would be fine..
Well I've tried booting up the rig and I get nothing on the screen (No Signal ) checked all sockets (graphics card, cpu)
I do get a little red and blue light on the board and the CPU fan and graphics fan are running fine,, but no signal...
I'm using a Intel Pentium 4, 2.8 GHz Processor Socket 775 which I know is fine,,,
Any views on this "you can use a 4pin plug on the 8pin CPU power socket " ?
Could this be the reason my rig is not booting ?
THanks

"Any views on this "you can use a 4pin plug on the 8pin CPU power socket " ?"
Yes you can. Make sure that 4pin cable is connected properly at correct side of 8pin socket.
"Could this be the reason my rig is not booting ?"
Nop. You can plug 8pin CPU cable if you want to test opposite Should boot with both 4 or 8.
Read >>Posting Guide<<

MSI P7N SLI Platinum Compatibility with Dominator PC10000

Hello forummer,its been a while since I last posted..I wanted to ask
I wanted to buy a MSI P7N SLI Platinum 750i motherboard and wonder if it fits my Corsair Dominator DDR2 1250MHz PC10000..
I read reviews that the most it can support is DDR2 800,hmm can it support the RAM ?thanks for ur help guys

Quote from: asamkipas on 15-March-09, 16:13:51
Hello forummer,its been a while since I last posted..I wanted to ask
I wanted to buy a MSI P7N SLI Platinum 750i motherboard and wonder if it fits my Corsair Dominator DDR2 1250MHz PC10000..
I read reviews that the most it can support is DDR2 800,hmm can it support the RAM ?thanks for ur help guys
DDR2-1250 is an overclocking rating. The memory modules should run fine @DDR2-800. Maybe you can stably overclock the modules to higher speeds, however, nobody can really guarantee you that those sticks will be able to operate @DDR2-1250 (625 MHz) on this board/chipset.

Msi p7n sli platinum ram chips problem

ok i have a msi p7n sli platinum mother board, i've had it now for the past 2 - 3 years. I finally got around to upgrading the ram from 2xcorsair xms2 ddr2 1024mb ram chips to 2x corsair dominator 2048mb ram chips.
i have checked the motherboard specs the voltage and MHz arent a problem.
But when i use 2 of the new chips my computer wont load the boot screen a 10th of the time. When i use 1 of the new chips it runs all the time. I was thinking it maybe a problem with the bios, i have reset it several times to the correct voltage, as it doesnt automatically some times.
anyone have and idea what i can do to fix this.

Please give full system specs --> >>Posting Guide<<
Try running the RAM at 800MHz 5-5-5-15 1.8V 2T.

HELP!!!!! P7n sli platinum cd-in problem.

Dear msi members.
I've got a p7n sli platinum board in, but now the cd-in (audio-in) (you know that 4 pinned thing you can connect a dvd drive too) connector on the board is in the way of my gtx 260, "they collide" now my question is, i'm pretty good at soldering, is it safe to unsolder the port completely?
as this way i'd have room for my gfx card.
If it's not. be sure to let me know how i can get this thing out of the way please.
Thanks in advance, Scorp.
P.s. Thats seriously my only issue, if i remove that thing everything will fit, (and i could mostlikely unsolder it carefully and resolder it should i need to rma). it's just the question that if i remove it completely does the board still run properly?

hello i have the same problem, i recently bought gtx260 to find out the JCD is on the way . I'm using my 2nd Pci-E slot at the moment. i was reading the forums and find out that this has been affecting many users with similar components, and they say they can remove the plastic as posted on this link http://forums.hardwarezone.com.sg/showthread.php?p=31163282 i
m not sure if that would void warranty or not

Run SATA and EIDE HDs (P7N SLI Platinum)

Similar Messages

Maybe you are looking for