Runcluvfy.sh failed on user equivalence check for user "oracle"
I have user oracle set up on both nodes -RHEL5 as:
uid=505(oracle) gid=87(oinstall) groups=87(oinstall),88(dba)
but when run the runcluvfy.sh stage -pre crsinst -n node1,node2 -verbose
get the ERROR:
user equivalence check failed for user "oracle"
user equivalence unavailable on all the nodes.
Help appreciated!
When you test this, are you using the fully qualified domain name (FQDN) like node1.domain.com or just node1? Oracle is most likely using the FQDN, so if you did "ssh node1 date" and that worked fine, I'll bet that "ssh node1.domain.com date" will result in a prompt to authorize the host first and that's probably the issue.
I also usually ssh over the private interface as well. That is, do both of these from the node where the installer runs:
ssh node2.domain.com date
ssh node2-priv.domain.com date ### assuming that node2-priv is the name of the private network interface
Let us know if that's the issue.
Dan
Similar Messages
-
Failed to activate authorization check for user SAPSYS
Hi Experts
I am trying to run the sdcc, it was throwing time_out error. i have increased the work process runtime. now
i am getting a error Failed to activate authorization check for user SAPSYS.
Please help me to solve this issue.
Regards
VenkatHi, Mr. Joe Bo.
Thanx for your reply. We are using ECC6 (HP Unix with Oracle)
Basis Patch - 15, Kernel 159
I have seen the the note but it's showing ccms method defination settings, but for my case we are yet to go live we have not made any settings from sap they are planning to run a session for the go live. When i am running sdcc i am getting a error in the system log "Failed to activate authorization check for user SAPSYS"
Thanks & Regards
Venkatesan J -
RUNCLUVFY Result: PRVF-4007 : User equivalence check failed for user "orac
hello
try to run runcluvfy.sh I receive the following screen rac2 is passed but rac 1 is failed can sombody help me?
thanks
[oracle@rac1 grid]$ ./runcluvfy.sh stage -pre crsinst -n rac1,rac2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "rac1"
Destination Node Reachable?
rac2 yes
rac1 yes
Result: Node reachability check passed from node "rac1"
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
rac2 passed
rac1 failed
Result: PRVF-4007 : User equivalence check failed for user "oracle"
WARNING:
User equivalence is not set for nodes:
rac1
Verification will proceed with nodes:
rac2
Checking node connectivity...Check this older thread which has a lot of information on this:
User equivalence check failed (RAC setup) -
Result: User equivalence check failed for user "oracle".
While installing on Solaris-10, ssh, rlogin, scp works fine.
Running runcluvfy.sh stage -post hwos -n rac-1,rac-2 -verbose returns the above error.
Result: User equivalence check failed for user "oracle".
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
/bin/ssh & /bin/scp is in use.Hello,
I am facing User equivalence check failed for user "oracle" error on my newly to be built RAC cluster.
The Oracle users have been created identically and ssh have been setup as per RAC installation manual.
Still I am facing the below problem. Please help me out
Node1 > uname -a
Linux purple-rac-node2 2.6.18-194.el5 #1 SMP Mon Mar 29 22:10:29 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux
Node2 > uname -a
Linux purple-rac-node1 2.6.18-194.el5 #1 SMP Mon Mar 29 22:10:29 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux
clusterware/cluvfy/runcluvfy.sh stage -post hwos -n purple-rac-node1,purple-rac-node2 -verbose
Performing post-checks for hardware and operating system setup
Checking node reachability...
Check: Node reachability from node "purple-rac-node1"
Destination Node Reachable?
purple-rac-node2 yes
purple-rac-node1 yes
Result: Node reachability check passed from node "purple-rac-node1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
purple-rac-node2 failed
purple-rac-node1 failed
Result: User equivalence check failed for user "oracle".
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
[oracle@purple-rac-node1 ~]$ id oracle
uid=501(oracle) gid=501(dba) groups=501(dba),502(oper),503(oinstall)
[oracle@purple-rac-node2 ~]$ id oracle
uid=501(oracle) gid=501(dba) groups=501(dba),502(oper),503(oinstall) -
User equivalence check failed for user "oracle".
Hi,
I am trying to install the Oracle Clusterware 10g as part of my RAC setup.
I have configured RHEL 4 in 2 nodes (rac and rac2). But when I run the runcluvfy utility, I get the below error:
[oracle@rac cluvfy]$ ./runcluvfy.sh stage -pre crsinst -n rac,rac2
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "rac".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
rac
WARNING:
User equivalence is not set for nodes:
rac
Verification will proceed with nodes:
rac2
The problem is only with the first node(rac). The second node passes succesfully.
ssh works fine. Not sure what is wrong!
Thanks!Did you do Configure SSH for User Equivalence ?
Or
Did you Establish User Equivalence ?
If yes.. please check...
$ ssh rac hostname
rac
$ ssh rac2 hostname
rac2
You should Establish User Equivalence before...
exec /usr/bin/ssh-agent $SHELL
/usr/bin/ssh-add
If You don't configure ssh for user equivalence
http://www.oracle.com/technology/pub/articles/smiley_rac10g_install.html
Or
read SSH User equivalence is not set up on the remote nodes -
User equivalence check failed for user "oracle" while running cluvfy
Hi All,
I am getting User equivalence error as follows while executing cluvfy. I want to install CRS on this server.
oracle@node200$ ./runcluvfy.sh stage -pre crsinst -n node200,node201,node202
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "node200".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
node202,node201,node200
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
I have sucessfully configured ssh and able to do ssh from all the nodes without prompting for the password. Also oracle uid and gid on all the servers are same.
I also checked in .kshrc file and there is no tty entry in that file. and I have also setup /etc/hosts.equiv file on all the node.
I still get the user equivalance error. Can anybody help me in this ?
Regards,
Raj.Hi,
thanks.
i need some more help because first time i am working on RAC,
i am also having User equivalence check failed for user "oracle"
i got two machines, one is IBM machine and one is DELL machine installed with solais 10 (AIX installation). both machines are not connected by private network now. and no shared external HDD available now. it will take one week time to set up the HW. the user equivalence check depends the above two factors?
now public network is available and node reachability test "passed"
could you please tell me what may be the reason for the user equivalence check in my case. details are given below
i have oracle user in both machine. user creation done through SMC. home directory is /export/home/oracle
the following are the details.
1) $ ssh pc000905 id -a oracle
Enter passphrase for key '/home/oracle/.ssh/id_rsa':
uid=100(oracle) gid=300(oinstall) groups=301(dba)
$ ssh pc026376 id -a oracle
Enter passphrase for key '/home/oracle/.ssh/id_rsa':
uid=100(oracle) gid=300(oinstall) groups=301(dba)
2) user nobody exists.
3) all files n .ssh directory have same permissions.
4) ssh and scp is working with out password(rsa and dsa keys generated).
5) oracle user is using bourne shell
6)soft link of /usr/bin/ssh and /usr/bin/scp are created to /export/home/oracle/bin
7)ForwardX11 is "yes" in sshd_config
8) created a config file in .ssh directory and ForwardX11 is "no" in that file
8) umask =022 in both nodes.
error displaying is
$/export/gome/cluvfy/runcluvfy.sh stage -pre crsinst -n pc026376,pc000905
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "PC026376".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
pc026376,pc000905
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
$ -
User equivalence check failed for user "oragrid" in HP-UX
Dear Friends,
while cluster verification utility i gotthe below error.
$ ./runcluvfy.sh stage -pre crsinst -n aeadsverp11-adp.adp.ae,aeadsverp12-adp.adp.ae -fixup -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "aeadsverp11-adp"
Destination Node Reachable?
aeadsverp11-adp yes
aeadsverp12-adp yes
Result: Node reachability check passed from node "aeadsverp11-adp"
Checking user equivalence...
Check: User equivalence for user "oragrid"
Node Name Comment
aeadsverp12-adp failed
aeadsverp11-adp failed
Result: PRVF-4007 : User equivalence check failed for user "oragrid"
ERROR:
User equivalence unavailable on all the specified nodes
Verification cannot proceed
Pre-check for cluster services setup was unsuccessful on all the nodes.
I had configred ssh and scp on both nodes.
$ ssh aeadsverp11-adp.adp.ae date
Wed Sep 28 04:26:55 MDT 2011
$
$ ssh aeadsverp12-adp.adp.ae date
Wed Sep 28 13:28:26 WAT 2011
ssh is wrking fine without any issues on both nodes.
Please advice.
Thanks,
RajendraHi,
Just ignore it and proceed with installation.
Its an bug.
Kind Regards,
Rakesh -
CLUVFY failing with 'User Equivalence check failed for...'
New 2 node RAC configuration. Oracle 10gR2, Linux RHEL 5 x64. I'm at the post hardware config, pre install clusterware stage.
Running the cluster verification utility command:
cluvfy comp sys -n node-01,node-02 -p crs -verboseReturns the following error:
Verifying system requirement
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Verification of system requirement was unsuccessful on all the nodes.I've verified the following:
1) RSA keys correctly configured on both nodes and I can ssh between without a password
2) ping ip and private work correctly to and from both nodes.
3) user, group ids are identical on both systems.
I also ran cluvfy stage -post hwos -n node-01,node-02 -verbose and received the following output. This output is from node-01. node-02's is identical, except with equivalence to itself failing.
Checking node reachability...
Check: Node reachability from node "node-01"
Destination Node Reachable?
node-02 yes
node-01 yes
Result: Node reachability check passed from node "node-01".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node-02 passed
node-01 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
node-01
Verification will proceed with nodes:
node-02
Checking node connectivity...I get the same behavior on both nodes. Not quite sure what else to check. Any thoughts or suggestions? Thanks.No, no banners. And I followed note 300548.1 to the letter. Several times :-)
However, I believe my issue has to do with a CVUHOME/cv/admin/cvu_config.
According to the documentation:
CV_XCHK_FOR_SSH_ENABLED—If set to TRUE, it enables the X-Windows check for verifying user equivalence with ssh. By default, this entry is commented out and X-Windows check is disabledIt was not, unfortunately, disabled by default - once I set it to false, everything succeeded. I still need to figure out why XCHK itself is failing, but I think I can troll through the log to figure that out. -
Result: PRVF-4007 : User equivalence check failed for user "oracle"
Hi
I get below error everytime I run ./cluvfy stage -pre crsinst -n node01,node02 -fixup -verbose > a.log
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node02 passed
node01 failed
Result: PRVF-4007 : User equivalence check failed for user "oracle"
WARNING:
User equivalence is not set for nodes:
node01
Verification will proceed with nodes:
node02
node01 is the local node, if I run from node02 It comes back saying the same thing about node2!
I have checked oracle uid and groups all set correctly and ssh working fine ...
I have ran the same command for grid user and getting the same error !!i know what it was, i should have done ssh localnode date for once at least!!
I only did ssh remotenode date :) -
PRVF-4007 : User equivalence check failed for user "grid"
Oracle Version 11.2.0.3.0 patched to 11.2.0.3.1
I had installed GIU and RAC db on 2 node cluster
but since yesterdy has this issue when running the commands
[grid@vmorarac2 ~]$ cluvfy comp ocr -n all -verbose
Verifying OCR integrity
ERROR:
PRVF-4008 : User equivalence unavailable on all the specified nodes
Verification cannot proceed
vmorarac1 and vmorarac2 r the two nodes
as a grid user, from vmorarac1 i ran ssh vmorarac2 and it failed with above error and vice versa
so i did the following
from vmorarac1
ssh vmorarac2
yes and enter key
exec /usr/bin/ssh-agent $SHELL
/usr/bin/ssh-add
i did the same on other node
but the problem still exists.
Edited by: 912919 on 23-May-2012 06:58Hi,
The subject of thread "*PRVF-4007 : User equivalence check failed for user "grid*"
Now..
{code}
PRVF-4657 : Name resolution setup check for "vmorarac-scan.pbi.global.pvt" (IP address: 152.144.199.201) failed
PRVF-4664 : Found inconsistent name resolution entries for SCAN name "vmorarac-scan.pbi.global.pvt"
PRVF-4664 : Found inconsistent name resolution entries for SCAN name "vmorarac-scan.pbi.global.pvt"
{code}
If you can see are different issue.
If you are using DSN to resolve hostname "vmorarac-scan.pbi.global.pvt" check with "nslookup" if the name is resolved correctly.
If you are using Hosts File to resolve hostname "vmorarac-scan.pbi.global.pvt" you must configure only one ip (152.144.199.201) to resolve "vmorarac-scan.pbi.global.pvt" this entrie must be on host file of all nodes of cluster.
Levi Pereira -
User equivalence check failed, both side say other node passed, why?
SPARC Soloris 10, clusterware 11gr1
two nodes cluster checking, both side say itself fail, other side is passed. why?
./runcluvfy.sh stage -pre crsinst -n bclabdb01,bclabdb02 -verbose
on node1(bclabdb0):
Checking user equivalence...
Check: User equivalence for user "crs"
Node Name Comment
bclabdb02 passed
bclabdb01 failed
Result: User equivalence check failed for user "crs".
WARNING:
User equivalence is not set for nodes:
bclabdb01
Verification will proceed with nodes:
bclabdb02
on node2:
Check: User equivalence for user "crs"
Node Name Comment
bclabdb02 failed
bclabdb01 passed
Result: User equivalence check failed for user "crs".
WARNING:
User equivalence is not set for nodes:
bclabdb02
Verification will proceed with nodes:
bclabdb01Hi
Which user equivalence you have configured rsh or ssh.If you have configured through ssh check it as oracle user through
ssh <nodename> <command>
if you have configure rsh then you need to create hosts.equiv file inside /etc/ and give proper permission to oracle user.Before installing clusterware I used CVU and its shown me passed for user equivalence .
Tinku -
User equivalence check failed in solaris 10
Hi,
i am trying to install oracle clusterware on solaris10.
when i executed clusture varification utility , user equivalence test is failed.
each node have same username,userid,group id
and i configured SSH also using
exec /user/bin/ssh-agent
/usr/bin/ssh-add after generation of rsa and dsa keys and putting this to authorization file.
it is not asking password for ssh and scp after executing this command but again user equivalence check failed
but after logging of and do login again to oracle user its not working. then again i have to set ssh that is
exec /user/bin/ssh-agent
/usr/bin/ssh-add
wat else i have to check for this?
can sombody help me to solve thisUmesh Gupta wrote:
Thay are same, i have already taken care of that..
Node1:-
$ id oracle
uid=101(oracle) gid=300(oinstall)
Node2:-
$ id oracle
uid=101(oracle) gid=300(oinstall)
Please suggest..
Regards
Umesh$exec /usr/bin/ssh-agent $SHELL
$/usr/bin/ssh-add
on any one of the nodes
and check the output of cluvfy
also refer the link:-
http://download.oracle.com/docs/cd/B28359_01/install.111/b28263/crsunix.htm#BEHIHBBF
User equivalence check failed (RAC setup)
Edited by: rajeysh on Aug 18, 2011 7:09 PM -
11g Cluster: User equivalence check failed on Node1 but passed on Node2,
From Node1:
[oracle@redhat4_1 bin]$ ./cluvfy stage -pre crsinst -n redhat4_1,redhat4_2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "redhat4_1"
Destination Node Reachable?
redhat4_2 yes
redhat4_1 yes
Result: Node reachability check passed from node "redhat4_1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
redhat4_2 passed
redhat4_1 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
redhat4_1
Verification will proceed with nodes:
redhat4_2
From Node2:
[oracle@redhat4_2 bin]$ ./cluvfy stage -pre crsinst -n redhat4_1,redhat4_2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "redhat4_2"
Destination Node Reachable?
redhat4_2 yes
redhat4_1 yes
Result: Node reachability check passed from node "redhat4_2".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
redhat4_2 passed
redhat4_1 passed
Result: User equivalence check passed for user "oracle".
Why cluvfy failed on node1 but passed on node2? Thanks.Last time I saw that, the password-less SSH was working only in one direction. Root cause was not quite following the instructions to copy the authorized_keys to all nodes.
-
User equivalence check failed (RAC setup)
Hello All,
I am trying to set up user equivalence between 2 nodes, following instructions from "Oracle® Database Oracle Clusterware and Oracle Real Application Clusters Installation Guide 10g Release 2 (10.2) for Solaris Operating System (SPARC 64-Bit)"
I have created user accounts on both nodes, .ssh folder with appropriate permissions, dsa and rsa keys on both nodes, copied them to authorized_keys on halfway, and scp authorozed_keys to wabasca. Now I am able to do 'ssh wabasca date' and 'ssh halfway date' on each node without being asked for password or passphrase:
$ whoami
ora10gr2
$ hostname
halfway
$ ssh halfway date
Thu Oct 6 16:51:37 MDT 2005
$ ssh wapiti date
Thu Oct 6 16:51:11 MDT 2005
$
$ whoami
ora10gr2
$ hostname
wapiti
$ ssh halfway date
Thu Oct 6 16:52:04 MDT 2005
$ ssh wapiti date
Thu Oct 6 16:51:38 MDT 2005
$Yet, the CVU verification of user equivalence fails:
$ whoami
ora10gr2
$ hostname
halfway
$ /Oracle10/cvu/bin/cluvfy comp admprv -n halfway,wapiti -o user_equiv -sshonly -verbose
Verifying administrative privileges
Checking user equivalence...
Check: User equivalence for user "ora10gr2"
Node Name Comment
wapiti failed
halfway failed
Result: User equivalence check failed for user "ora10gr2".
Verification of administrative privileges was unsuccessful on all the nodes.
$If I can 'ssh <nodename> date' sucessfully what may cause the CVU check of user equivalence to fail? (I see that timing is off between these 2 machines...)
Thank you very much for your time.
DanielDIt turns out that CVU is also requiring scp to be in /usr/local/bin; the idiot thing doesn't even try to use the scp that's in the execution $PATH, and on Solaris ends up failing silently early in the script (when ssh is in /usr/local/bin and scp is not).
I was finally able to figure out what was foobar'ed by turning on the trace mode and reviewing the logs:
export SRVM_TRACE=true
cluvfy stage -pre crsinst -n tri1-ora1,tri1-ora2 -verbose
This leaves you with log files in the CVU installation directory, under [CVU_HOME]/cv/log/; in mine I found...
[Worker 0] [20:7:53:400] [RuntimeExec.runCommand:74] Calling Runtime.exec() with the command ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:400] [RuntimeExec.runCommand:76] /usr/local/bin/scp ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:400] [RuntimeExec.runCommand:76] -p ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:401] [RuntimeExec.runCommand:76] /opt/oracle/cvu//cv/remenv/exectask ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:401] [RuntimeExec.runCommand:76] tri1-ora2:/tmp//CVU_10.2.0.1.0.1_oinstall/exectask ; Fri Nov 18 20:07:53 GMT+00:00 2005
[Worker 0] [20:7:53:402] [RuntimeExec.runCommand:90] exec exception:/usr/local/bin/scp: not found; Fri Nov 18 20:07:53 GMT+00:00 2005
Whoever programmed this thing seems slightly naive about host environment checking. Also, the Sun ssh package by default installs ssh and scp in /usr/bin; it's pretty popular to install the 3rd-party package that goes into /usr/local/bin though... -
Failing all pre-requisite checks for 11.2.0.2.0 RAC on HP-UX Itanium 64
Hi Guys,
For Typical OR Advanced Grid Installation (GUI), all pre-requisites are failing on both nodes, like memory, swap, node reachability, groups, user & lot more.....
But when I try to check Pre-requisite from command line, everything seems to be ok.
This is what the output...
$ ./runcluvfy.sh stage -pre crsinst -n sph1erp,sph2erp -fixup -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "sph1erp"
Destination Node Reachable?
sph1erp yes
sph2erp yes
Result: Node reachability check passed from node "sph1erp"
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
sph2erp passed
sph1erp passed
Result: User equivalence check passed for user "oracle"
Checking node connectivity...
Checking hosts config file...
Node Name Status Comment
sph2erp passed
sph1erp passed
Verification of the hosts config file successful
Interface information for node "sph2erp"
Name IP Address Subnet Gateway Def. Gateway HW Address MTU
lan2 10.10.16.51 10.10.16.48 10.10.16.51 10.10.1.12 78:AC:C0:8A:07:76 1500
lan900 10.10.1.174 10.10.0.0 10.10.1.174 10.10.1.12 78:AC:C0:8A:07:6E 1500
Interface information for node "sph1erp"
Name IP Address Subnet Gateway Def. Gateway HW Address MTU
lan2 10.10.16.50 10.10.16.48 10.10.16.50 10.10.1.12 3C:4A:92:48:71:BE 1500
lan900 10.10.1.173 10.10.0.0 10.10.1.173 10.10.1.12 3C:4A:92:48:71:B6 1500
Check: Node connectivity of subnet "10.10.16.48"
Source Destination Connected?
sph2erp[10.10.16.51] sph1erp[10.10.16.50] yes
Result: Node connectivity passed for subnet "10.10.16.48" with node(s) sph2erp,sph1erp
Check: TCP connectivity of subnet "10.10.16.48"
Source Destination Connected?
sph1erp:10.10.16.50 sph2erp:10.10.16.51 passed
Result: TCP connectivity check passed for subnet "10.10.16.48"
Check: Node connectivity of subnet "10.10.0.0"
Source Destination Connected?
sph2erp[10.10.1.174] sph1erp[10.10.1.173] yes
Result: Node connectivity passed for subnet "10.10.0.0" with node(s) sph2erp,sph1erp
Check: TCP connectivity of subnet "10.10.0.0"
Source Destination Connected?
sph1erp:10.10.1.173 sph2erp:10.10.1.174 passed
Result: TCP connectivity check passed for subnet "10.10.0.0"
Interfaces found on subnet "10.10.0.0" that are likely candidates for VIP are:
sph2erp lan900:10.10.1.174
sph1erp lan900:10.10.1.173
Interfaces found on subnet "10.10.16.48" that are likely candidates for a private interconnect are:
sph2erp lan2:10.10.16.51
sph1erp lan2:10.10.16.50
Result: Node connectivity check passed
Check: Total memory
Node Name Available Required Comment
sph2erp 63.9GB (6.7004024E7KB) 4GB (4194304.0KB) passed
sph1erp 63.9GB (6.7004024E7KB) 4GB (4194304.0KB) passed
Result: Total memory check passed
Check: Available memory
Node Name Available Required Comment
sph2erp 53.3556GB (5.5947372E7KB) 50MB (51200.0KB) passed
sph1erp 52.2323GB (5.47695E7KB) 50MB (51200.0KB) passed
Result: Available memory check passed
Check: Swap space
Node Name Available Required Comment
sph2erp 188.7773GB (1.97947352E8KB) 4GB (4194304.0KB) passed
sph1erp 188.7773GB (1.97947352E8KB) 4GB (4194304.0KB) passed
Result: Swap space check passed
Check: Free disk space for "sph2erp:/var/tmp/"
Path Node Name Mount point Available Required Comment
/var/tmp/ sph2erp /var 13.8074GB 1GB passed
Result: Free disk space check passed for "sph2erp:/var/tmp/"
Check: Free disk space for "sph1erp:/var/tmp/"
Path Node Name Mount point Available Required Comment
/var/tmp/ sph1erp /var 13.8158GB 1GB passed
Result: Free disk space check passed for "sph1erp:/var/tmp/"
Check: User existence for "oracle"
Node Name Status Comment
sph2erp exists(199) passed
sph1erp exists(199) passed
Checking for multiple users with UID value 199
Result: Check for multiple users with UID value 199 passed
Result: User existence check passed for "oracle"
Check: Group existence for "oinstall"
Node Name Status Comment
sph2erp exists passed
sph1erp exists passed
Result: Group existence check passed for "oinstall"
Check: Group existence for "dba"
Node Name Status Comment
sph2erp exists passed
sph1erp exists passed
Result: Group existence check passed for "dba"
Check: Membership of user "oracle" in group "oinstall" [as Primary]
Node Name User Exists Group Exists User in Group Primary Comment
sph2erp yes yes yes yes passed
sph1erp yes yes yes yes passed
Result: Membership check for user "oracle" in group "oinstall" [as Primary] passed
Check: Membership of user "oracle" in group "dba"
Node Name User Exists Group Exists User in Group Comment
sph2erp yes yes yes passed
sph1erp yes yes yes passed
Result: Membership check for user "oracle" in group "dba" passed
Check: Run level
Node Name run level Required Comment
sph2erp 3 3 passed
sph1erp 3 3 passed
Result: Run level check passed
Check: Hard limits for "maximum open file descriptors"
Node Name Type Available Required Comment
sph2erp hard 63488 63488 passed
sph1erp hard 63488 63488 passed
Result: Hard limits check passed for "maximum open file descriptors"
Check: Soft limits for "maximum open file descriptors"
Node Name Type Available Required Comment
sph2erp soft 1024 1024 passed
sph1erp soft 63488 1024 passed
Result: Soft limits check passed for "maximum open file descriptors"
Check: Hard limits for "maximum user processes"
Node Name Type Available Required Comment
sph2erp hard 3687 3686 passed
sph1erp hard 3687 3686 passed
Result: Hard limits check passed for "maximum user processes"
Check: Soft limits for "maximum user processes"
Node Name Type Available Required Comment
sph2erp soft 3687 2047 passed
sph1erp soft 3687 2047 passed
Result: Soft limits check passed for "maximum user processes"
Check: System architecture
Node Name Available Required Comment
sph2erp ia64 ia64 passed
sph1erp ia64 ia64 passed
Result: System architecture check passed
Check: Kernel version
Node Name Available Required Comment
sph2erp HP-UX B.11.31 B.11.31 passed
sph1erp HP-UX B.11.31 B.11.31 passed
Result: Kernel version check passed
Check: Kernel parameter for "ksi_alloc_max"
Node Name Configured Required Comment
sph2erp 32768 32768 passed
sph1erp 32768 32768 passed
Result: Kernel parameter check passed for "ksi_alloc_max"
Check: Kernel parameter for "executable_stack"
Node Name Configured Required Comment
sph2erp 0 0 passed
sph1erp 0 0 passed
Result: Kernel parameter check passed for "executable_stack"
Check: Kernel parameter for "max_thread_proc"
Node Name Configured Required Comment
sph2erp 1024 1024 passed
sph1erp 1024 1024 passed
Result: Kernel parameter check passed for "max_thread_proc"
Check: Kernel parameter for "maxdsiz"
Node Name Configured Required Comment
sph2erp 1073741824 1073741824 passed
sph1erp 1073741824 1073741824 passed
Result: Kernel parameter check passed for "maxdsiz"
Check: Kernel parameter for "maxdsiz_64bit"
Node Name Configured Required Comment
sph2erp 2147483648 2147483648 passed
sph1erp 2147483648 2147483648 passed
Result: Kernel parameter check passed for "maxdsiz_64bit"
Check: Kernel parameter for "maxssiz"
Node Name Configured Required Comment
sph2erp 134217728 134217728 passed
sph1erp 134217728 134217728 passed
Result: Kernel parameter check passed for "maxssiz"
Check: Kernel parameter for "maxssiz_64bit"
Node Name Configured Required Comment
sph2erp 1073741824 1073741824 passed
sph1erp 1073741824 1073741824 passed
Result: Kernel parameter check passed for "maxssiz_64bit"
Check: Kernel parameter for "maxuprc"
Node Name Configured Required Comment
sph2erp 3686 3686 passed
sph1erp 3686 3686 passed
Result: Kernel parameter check passed for "maxuprc"
Check: Kernel parameter for "msgmni"
Node Name Configured Required Comment
sph2erp 4096 4096 passed
sph1erp 4096 4096 passed
Result: Kernel parameter check passed for "msgmni"
Check: Kernel parameter for "msgtql"
Node Name Configured Required Comment
sph2erp 4096 4096 passed
sph1erp 4096 4096 passed
Result: Kernel parameter check passed for "msgtql"
Check: Kernel parameter for "ncsize"
Node Name Configured Required Comment
sph2erp 35840 35840 passed
sph1erp 35840 35840 passed
Result: Kernel parameter check passed for "ncsize"
Check: Kernel parameter for "shmmax"
Node Name Configured Required Comment
sph2erp 1073741824 1073741824 passed
sph1erp 1073741824 1073741824 passed
Result: Kernel parameter check passed for "shmmax"
Check: Kernel parameter for "shmmni"
Node Name Configured Required Comment
sph2erp 4096 4096 passed
sph1erp 4096 4096 passed
Result: Kernel parameter check passed for "shmmni"
Check: Kernel parameter for "shmseg"
Node Name Configured Required Comment
sph2erp 512 512 passed
sph1erp 512 512 passed
Result: Kernel parameter check passed for "shmseg"
Check: Kernel parameter for "tcp_smallest_anon_port"
Node Name Configured Required Comment
sph2erp 9000 9000 passed
sph1erp 9000 9000 passed
Result: Kernel parameter check passed for "tcp_smallest_anon_port"
Check: Kernel parameter for "tcp_largest_anon_port"
Node Name Configured Required Comment
sph2erp 65500 65500 passed
sph1erp 65500 65500 passed
Result: Kernel parameter check passed for "tcp_largest_anon_port"
Check: Kernel parameter for "udp_smallest_anon_port"
Node Name Configured Required Comment
sph2erp 9000 9000 passed
sph1erp 9000 9000 passed
Result: Kernel parameter check passed for "udp_smallest_anon_port"
Check: Kernel parameter for "udp_largest_anon_port"
Node Name Configured Required Comment
sph2erp 65500 65500 passed
sph1erp 65500 65500 passed
Result: Kernel parameter check passed for "udp_largest_anon_port"
Check: Package existence for "OS-Core-B.11.31( ia64)"
Node Name Available Required Comment
sph2erp OS-Core-B.11.31-0 OS-Core-B.11.31( ia64) passed
sph1erp OS-Core-B.11.31-0 OS-Core-B.11.31( ia64) passed
Result: Package existence check passed for "OS-Core-B.11.31( ia64)"
Check: Operating system patch for "Patch PHKL_38938"
Node Name Applied Required Comment
sph2erp Patch PHKL_39646 Patch PHKL_38938 passed
sph1erp Patch PHKL_39646 Patch PHKL_38938 passed
Result: Operating system patch check passed for "Patch PHKL_38938"
Check: Operating system patch for "Patch PHKL_39351"
Node Name Applied Required Comment
sph2erp Patch PHKL_40207 Patch PHKL_39351 passed
sph1erp Patch PHKL_40207 Patch PHKL_39351 passed
Result: Operating system patch check passed for "Patch PHKL_39351"
Check: Operating system patch for "Patch PHSS_36354"
Node Name Applied Required Comment
sph2erp Patch PHSS_40546 Patch PHSS_36354 passed
sph1erp Patch PHSS_40546 Patch PHSS_36354 passed
Result: Operating system patch check passed for "Patch PHSS_36354"
Check: Operating system patch for "Patch PHSS_37042"
Node Name Applied Required Comment
sph2erp Patch PHSS_37042 Patch PHSS_37042 passed
sph1erp Patch PHSS_37042 Patch PHSS_37042 passed
Result: Operating system patch check passed for "Patch PHSS_37042"
Check: Operating system patch for "Patch PHSS_37959"
Node Name Applied Required Comment
sph2erp Patch PHSS_40804 Patch PHSS_37959 passed
sph1erp Patch PHSS_40804 Patch PHSS_37959 passed
Result: Operating system patch check passed for "Patch PHSS_37959"
Check: Operating system patch for "Patch PHSS_39094"
Node Name Applied Required Comment
sph2erp Patch PHSS_40538 Patch PHSS_39094 passed
sph1erp Patch PHSS_40538 Patch PHSS_39094 passed
Result: Operating system patch check passed for "Patch PHSS_39094"
Check: Operating system patch for "Patch PHSS_39100"
Node Name Applied Required Comment
sph2erp Patch PHSS_40540 Patch PHSS_39100 passed
sph1erp Patch PHSS_40540 Patch PHSS_39100 passed
Result: Operating system patch check passed for "Patch PHSS_39100"
Check: Operating system patch for "Patch PHSS_39102"
Node Name Applied Required Comment
sph2erp Patch PHSS_41496 Patch PHSS_39102 passed
sph1erp Patch PHSS_41496 Patch PHSS_39102 passed
Result: Operating system patch check passed for "Patch PHSS_39102"
Check: Operating system patch for "Patch PHSS_38141"
Node Name Applied Required Comment
sph2erp Patch PHSS_38141 Patch PHSS_38141 passed
sph1erp Patch PHSS_38141 Patch PHSS_38141 passed
Result: Operating system patch check passed for "Patch PHSS_38141"
Check: Operating system patch for "Patch PHCO_40381"
Node Name Applied Required Comment
sph2erp Patch PHCO_40381 Patch PHCO_40381 passed
sph1erp Patch PHCO_40381 Patch PHCO_40381 passed
Result: Operating system patch check passed for "Patch PHCO_40381"
Check: Operating system patch for "Patch PHKL_38038"
Node Name Applied Required Comment
sph2erp Patch PHKL_41005 Patch PHKL_38038 passed
sph1erp Patch PHKL_41005 Patch PHKL_38038 passed
Result: Operating system patch check passed for "Patch PHKL_38038"
Checking for multiple users with UID value 0
Result: Check for multiple users with UID value 0 passed
Check: Current group ID
Result: Current group ID check passed
Starting Clock synchronization checks using Network Time Protocol(NTP)...
NTP Configuration file check started...
Network Time Protocol(NTP) configuration file not found on any of the nodes. Oracle Cluster Time Synchronization Service(CTSS) can be used instead of NTP for time synchronization on the cluster nodes
No NTP Daemons or Services were found to be running
Result: Clock synchronization check using Network Time Protocol(NTP) passed
Checking Core file name pattern consistency...
Core file name pattern consistency check passed.
Checking to make sure user "oracle" is not in "root" group
Node Name Status Comment
sph2erp does not exist passed
sph1erp does not exist passed
Result: User "oracle" is not part of "root" group. Check passed
Check default user file creation mask
Node Name Available Required Comment
sph2erp 022 0022 passed
sph1erp 022 0022 passed
Result: Default user file creation mask check passed
Checking consistency of file "/etc/resolv.conf" across nodes
Node Name Status
sph2erp passed
sph1erp passed
The DNS response time for an unreachable node is within acceptable limit on all nodes
File "/etc/resolv.conf" is consistent across nodes
Check: Time zone consistency
Result: Time zone consistency check passed
Checking settings of device file "/dev/async"
Node Name Available Comment
sph2erp yes failed (incorrect setting for minor number.)
sph1erp yes failed (incorrect setting for minor number.)
Result: Check for settings of device file "/dev/async" failed.
Starting check for The SSH LoginGraceTime setting ...
WARNING:
PRVE-0038 : The SSH LoginGraceTime setting on node "sph2erp" may result in users being disconnected before login is completed
PRVE-0038 : The SSH LoginGraceTime setting on node "sph1erp" may result in users being disconnected before login is completed
Check for The SSH LoginGraceTime setting passed
Fixup information has been generated for following node(s):
sph2erp,sph1erp
Please run the following script on each node as "root" user to execute the fixups:
'/tmp/CVU_11.2.0.2.0_oracle/runfixup.sh'
Pre-check for cluster services setup was unsuccessful on all the nodes.
What could be the issue ????
Any help would be appreciated...
Regards,
ManishStarted with Grid Installation. Copying Software to remote node & linking libraries were successfully without any issue (upto 76%). But got issue while executing root.sh on Node1
sph1erp:/oracle/11.2.0/grid #sh root.sh
Running Oracle 11g root script...
The following environment variables are set as:
ORACLE_OWNER= oracle
ORACLE_HOME= /oracle/11.2.0/grid
Enter the full pathname of the local bin directory: [usr/local/bin]:
Copying dbhome to /usr/local/bin ...
Copying oraenv to /usr/local/bin ...
Copying coraenv to /usr/local/bin ...
Creating /etc/oratab file...
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
Using configuration parameter file: /oracle/11.2.0/grid/crs/install/crsconfig_params
Creating trace directory
LOCAL ADD MODE
Creating OCR keys for user 'root', privgrp 'sys'..
Operation successful.
OLR initialization - successful
root wallet
root wallet cert
root cert export
peer wallet
profile reader wallet
pa wallet
peer wallet keys
pa wallet keys
peer cert request
pa cert request
peer cert
pa cert
peer root cert TP
profile reader root cert TP
pa root cert TP
peer pa cert TP
pa peer cert TP
profile reader pa cert TP
profile reader peer cert TP
peer user cert
pa user cert
Adding daemon to inittab
CRS-2672: Attempting to start 'ora.mdnsd' on 'sph1erp'
CRS-2676: Start of 'ora.mdnsd' on 'sph1erp' succeeded
CRS-2672: Attempting to start 'ora.gpnpd' on 'sph1erp'
CRS-2676: Start of 'ora.gpnpd' on 'sph1erp' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 'sph1erp'
CRS-2672: Attempting to start 'ora.gipcd' on 'sph1erp'
CRS-2676: Start of 'ora.gipcd' on 'sph1erp' succeeded
CRS-2676: Start of 'ora.cssdmonitor' on 'sph1erp' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 'sph1erp'
CRS-2672: Attempting to start 'ora.diskmon' on 'sph1erp'
CRS-2676: Start of 'ora.diskmon' on 'sph1erp' succeeded
CRS-2676: Start of 'ora.cssd' on 'sph1erp' succeeded
ASM created and started successfully.
Disk Group OCRVOTE created successfully.
clscfg: -install mode specified
Successfully accumulated necessary OCR keys.
Creating OCR keys for user 'root', privgrp 'sys'..
Operation successful.
CRS-4256: Updating the profile
Successful addition of voting disk ab847ed2b4f04f2dbfb875226d2bb194.
Successful addition of voting disk 85c05a5b30384f8dbff48cc069de7a7c.
Successful addition of voting disk 649196fbdd614f9cbf26a9a0e6670a6e.
Successful addition of voting disk 8815dfcee2e64f64bf00b9c76626ab41.
Successful addition of voting disk 8ce55fe5534f4f77bfa9f54187592707.
Successfully replaced voting disk group with +OCRVOTE.
CRS-4256: Updating the profile
CRS-4266: Voting file(s) successfully replaced
## STATE File Universal Id File Name Disk group
1. ONLINE ab847ed2b4f04f2dbfb875226d2bb194 (/dev/oracle/ocrvote1) [OCRVOTE]
2. ONLINE 85c05a5b30384f8dbff48cc069de7a7c (/dev/oracle/ocrvote2) [OCRVOTE]
3. ONLINE 649196fbdd614f9cbf26a9a0e6670a6e (/dev/oracle/ocrvote3) [OCRVOTE]
4. ONLINE 8815dfcee2e64f64bf00b9c76626ab41 (/dev/oracle/ocrvote4) [OCRVOTE]
5. ONLINE 8ce55fe5534f4f77bfa9f54187592707 (/dev/oracle/ocrvote5) [OCRVOTE]
Located 5 voting disk(s).
Start of resource "ora.cluster_interconnect.haip" failed
CRS-2672: Attempting to start 'ora.cluster_interconnect.haip' on 'sph1erp'
CRS-5017: The resource action "ora.cluster_interconnect.haip start" encountered the following error:
Start action for HAIP aborted
CRS-2674: Start of 'ora.cluster_interconnect.haip' on 'sph1erp' failed
CRS-2679: Attempting to clean 'ora.cluster_interconnect.haip' on 'sph1erp'
CRS-2681: Clean of 'ora.cluster_interconnect.haip' on 'sph1erp' succeeded
CRS-4000: Command Start failed, or completed with errors.
Failed to start Oracle Clusterware stack
Failed to start High Availability IP at /oracle/11.2.0/grid/crs/install/crsconfig_lib.pm line 1046.
/oracle/11.2.0/grid/perl/bin/perl -I/oracle/11.2.0/grid/perl/lib -I/oracle/11.2.0/grid/crs/install /oracle/11.2.0/grid/crs/install/rootcrs.pl execution failed
sph1erp:/oracle/11.2.0/grid #
Last few lines from CRS Log for node 1, where error came
[ctssd(6467)]CRS-2401:The Cluster Time Synchronization Service started on host sph1erp.
2011-02-25 23:04:16.491
[oracle/11.2.0/grid/bin/orarootagent.bin(6423)]CRS-5818:Aborted command 'start for resource: ora.cluster_interconnect.haip 1 1' for resource 'ora.cluster_int
erconnect.haip'. Details at (:CRSAGF00113:) {0:0:178} in */oracle/11.2.0/grid/log/sph1erp/agent/ohasd/orarootagent_root/orarootagent_root.log.*
2011-02-25 23:04:20.521
[ohasd(5513)]CRS-2757:Command 'Start' timed out waiting for response from the resource 'ora.cluster_interconnect.haip'. Details at (:CRSPE00111:) {0:0:178} in
*/oracle/11.2.0/grid/log/sph1erp/ohasd/ohasd.log.*
Few lines from */oracle/11.2.0/grid/log/sph1erp/agent/ohasd/orarootagent_root/orarootagent_root.log.*
=====================================================================================================
2011-02-25 23:04:16.823: [ USRTHRD][16] {0:0:178} Starting Probe for ip 169.254.74.54
2011-02-25 23:04:16.823: [ USRTHRD][16] {0:0:178} Transitioning to Probe State
2011-02-25 23:04:17.177: [ USRTHRD][15] {0:0:178} [NetHAMain] thread stopping
2011-02-25 23:04:17.177: [ USRTHRD][15] {0:0:178} Thread:[NetHAMain]isRunning is reset to false here
2011-02-25 23:04:17.178: [ USRTHRD][12] {0:0:178} Thread:[NetHAMain]stop }
2011-02-25 23:04:17.178: [ USRTHRD][12] {0:0:178} thread cleaning up
2011-02-25 23:04:17.178: [ USRTHRD][12] {0:0:178} pausing thread
2011-02-25 23:04:17.178: [ USRTHRD][12] {0:0:178} posting thread
2011-02-25 23:04:17.178: [ USRTHRD][12] {0:0:178} Thread:[NetHAWork]stop {
2011-02-25 23:04:17.645: [ USRTHRD][16] {0:0:178} [NetHAWork] thread stopping
2011-02-25 23:04:17.645: [ USRTHRD][16] {0:0:178} Thread:[NetHAWork]isRunning is reset to false here
2011-02-25 23:04:17.645: [ USRTHRD][12] {0:0:178} Thread:[NetHAWork]stop }
2011-02-25 23:04:17.645: [ USRTHRD][12] {0:0:178} Thread:[NetHAWork]stop {
2011-02-25 23:04:17.645: [ USRTHRD][12] {0:0:178} Thread:[NetHAWork]stop }
2011-02-25 23:04:17.891: [ora.cluster_interconnect.haip][12] {0:0:178} [start] Start of HAIP aborted
2011-02-25 23:04:17.892: [ AGENT][12] {0:0:178} UserErrorException: Locale is
2011-02-25 23:04:17.893: [ora.cluster_interconnect.haip][12] {0:0:178} [start] clsnUtils::error Exception type=2 string=
CRS-5017: The resource action "ora.cluster_interconnect.haip start" encountered the following error:
Start action for HAIP aborted
2011-02-25 23:04:17.893: [ AGFW][12] {0:0:178} sending status msg [CRS-5017: The resource action "ora.cluster_interconnect.haip start" encountered the foll
owing error:
Start action for HAIP aborted
] for start for resource: ora.cluster_interconnect.haip 1 1
2011-02-25 23:04:17.893: [ora.cluster_interconnect.haip][12] {0:0:178} [start] clsn_agent::start }
2011-02-25 23:04:17.894: [ AGFW][10] {0:0:178} Agent sending reply for: RESOURCE_START[ora.cluster_interconnect.haip 1 1] ID 4098:661
2011-02-25 23:04:18.552: [ora.diskmon][12] {0:0:154} [check] DiskmonAgent::check {
2011-02-25 23:04:18.552: [ora.diskmon][12] {0:0:154} [check] DiskmonAgent::check } - 0
2011-02-25 23:04:19.573: [ AGFW][10] {0:0:154} Agent received the message: AGENT_HB[Engine] ID 12293:669
2011-02-25 23:04:20.510: [ora.cluster_interconnect.haip][18] {0:0:178} [start] got lock
2011-02-25 23:04:20.511: [ora.cluster_interconnect.haip][18] {0:0:178} [start] tryActionLock }
2011-02-25 23:04:20.511: [ora.cluster_interconnect.haip][18] {0:0:178} [start] abort }
2011-02-25 23:04:20.511: [ora.cluster_interconnect.haip][18] {0:0:178} [start] clsn_agent::abort }
2011-02-25 23:04:20.511: [ AGFW][18] {0:0:178} Command: start for resource: ora.cluster_interconnect.haip 1 1 completed with status: TIMEDOUT
2011-02-25 23:04:20.512: [ora.cluster_interconnect.haip][8] {0:0:178} [check] NetworkAgent::init enter {
2011-02-25 23:04:20.513: [ora.cluster_interconnect.haip][8] {0:0:178} [check] NetworkAgent::init exit }
2011-02-25 23:04:20.517: [ AGFW][10] {0:0:178} Agent sending reply for: RESOURCE_START[ora.cluster_interconnect.haip 1 1] ID 4098:661
2011-02-25 23:04:20.519: [ USRTHRD][8] {0:0:178} Ocr Context init default level 23886304
2011-02-25 23:04:20.519: [ default][8]clsvactversion:4: Retrieving Active Version from local storage.
[ CLWAL][8]clsw_Initialize: OLR initlevel [70000]
Few lines from */oracle/11.2.0/grid/log/sph1erp/ohasd/ohasd.log.*
=====================================================================================================
2011-02-25 23:04:21.627: [UiServer][30] {0:0:180} Done for ctx=6000000002604ce0
2011-02-25 23:04:21.642: [UiServer][31] Closed: remote end failed/disc.
2011-02-25 23:04:26.139: [ CLSINET][33]Returning NETDATA: 1 interfaces
2011-02-25 23:04:26.139: [ CLSINET][33]# 0 Interface 'lan2',ip='10.10.16.50',mac='3c-4a-92-48-71-be',mask='255.255.255.240',net='10.10.16.48',use='cluster_int
erconnect'
2011-02-25 23:04:26.973: [UiServer][31] CS(60000000014b0790)set Properties ( root,60000000012e0260)
2011-02-25 23:04:26.973: [UiServer][31] SS(6000000001372270)Accepted client connection: saddr =(ADDRESS=(PROTOCOL=ipc)(DEV=92)(KEY=OHASD_UI_SOCKET))daddr = (A
DDRESS=(PROTOCOL=ipc)(KEY=OHASD_UI_SOCKET))
2011-02-25 23:04:26.992: [UiServer][30] {0:0:181} processMessage called
2011-02-25 23:04:26.993: [UiServer][30] {0:0:181} Sending message to PE. ctx= 6000000001b440f0
2011-02-25 23:04:26.993: [UiServer][30] {0:0:181} Sending command to PE: 67
2011-02-25 23:04:26.994: [ CRSPE][29] {0:0:181} Processing PE command id=173. Description: [Stat Resource : 600000000135f760]
2011-02-25 23:04:26.997: [UiServer][30] {0:0:181} Done for ctx=6000000001b440f0
2011-02-25 23:04:27.012: [UiServer][31] Closed: remote end failed/disc.
2011-02-25 23:04:31.135: [ CLSINET][33]Returning NETDATA: 1 interfaces
2011-02-25 23:04:31.135: [ CLSINET][33]# 0 Interface 'lan2',ip='10.10.16.50',mac='3c-4a-92-48-71-be',mask='255.255.255.240',net='10.10.16.48',use='cluster_int
erconnect'
2011-02-25 23:04:32.318: [UiServer][31] CS(60000000014b0790)set Properties ( root,60000000012e0260)
2011-02-25 23:04:32.318: [UiServer][31] SS(6000000001372270)Accepted client connection: saddr =(ADDRESS=(PROTOCOL=ipc)(DEV=92)(KEY=OHASD_UI_SOCKET))daddr = (A
DDRESS=(PROTOCOL=ipc)(KEY=OHASD_UI_SOCKET))
2011-02-25 23:04:32.332: [UiServer][30] {0:0:182} processMessage called
2011-02-25 23:04:32.333: [UiServer][30] {0:0:182} Sending message to PE. ctx= 6000000001b45ef0
2011-02-25 23:04:32.333: [UiServer][30] {0:0:182} Sending command to PE: 68
2011-02-25 23:04:32.334: [ CRSPE][29] {0:0:182} Processing PE command id=174. Description: [Stat Resource : 600000000135f760]
2011-02-25 23:04:32.338: [UiServer][30] {0:0:182} Done for ctx=6000000001b45ef0
2011-02-25 23:04:32.352: [UiServer][31] Closed: remote end failed/disc.
2011-02-25 23:04:36.155: [ CLSINET][33]Returning NETDATA: 1 interfaces
2011-02-25 23:04:36.155: [ CLSINET][33]# 0 Interface 'lan2',ip='10.10.16.50',mac='3c-4a-92-48-71-be',mask='255.255.255.240',net='10.10.16.48',use='cluster_int
erconnect'
2011-02-25 23:04:37.683: [UiServer][31] CS(60000000014b0790)set Properties ( root,60000000012e0260)
2011-02-25 23:04:37.683: [UiServer][31] SS(6000000001372270)Accepted client connection: saddr =(ADDRESS=(PROTOCOL=ipc)(DEV=92)(KEY=OHASD_UI_SOCKET))daddr = (A
DDRESS=(PROTOCOL=ipc)(KEY=OHASD_UI_SOCKET))
2011-02-25 23:04:37.702: [UiServer][30] {0:0:183} processMessage called
2011-02-25 23:04:37.703: [UiServer][30] {0:0:183} Sending message to PE. ctx= 6000000002604ce0
2011-02-25 23:04:37.703: [UiServer][30] {0:0:183} Sending command to PE: 69
2011-02-25 23:04:37.704: [ CRSPE][29] {0:0:183} Processing PE command id=175. Description: [Stat Resource : 600000000135f760]
2011-02-25 23:04:37.708: [UiServer][30] {0:0:183} Done for ctx=6000000002604ce0
2011-02-25 23:04:37.722: [UiServer][31] Closed: remote end failed/disc.
2011-02-25 23:04:41.156: [ CLSINET][33]Returning NETDATA: 1 interfaces
2011-02-25 23:04:41.156: [ CLSINET][33]# 0 Interface 'lan2',ip='10.10.16.50',mac='3c-4a-92-48-71-be',mask='255.255.255.240',net='10.10.16.48',use='cluster_int
erconnect'
What could be the issue ????
Experts Please help me. Doing setup for the PRoduction Env...
Do response ASAP...... Thanks
Regards,
Manish
Maybe you are looking for
-
Final Cut Studio 2(Color) and AGP graphics cards
So I have ordered FCS 2 for my business(Videography with HDV cameras). I am on the 2.0 Ghz G5 with dual processors and a 23' Apple Cinema Display. The computer came with the ATI 9600 Pro Radeon card. All the technical requirements for Color are PCI s
-
Is there a way to zoom images in and out without changing the frame?
It is easy to move an image around within a frame without touching the frame, but I have not found a way to zoom in and out without touching the frame. I'm working with a lot of images (Indesign CS6 for PC) and I need to do this a lot. Thanks.
-
How to restrict the PA30 and PA40.
Dear Experts, Need so help to resolve the below issue. Through the ABAP-HR program we are sending an email to the particular mail ID. FOR HIRING A NEW EMPLOYEE: while performing PA40 it has give authorization to user to update 0000,0001 and 0002 and
-
Changing Dimensions of menu items in menubar
I wanted to make the menu items have an auto width instead of a fixed with. So I followed the direction in the Help file under "Change dimensions of menu items" to change the .css. The menu items now seem to stretch to fit the width of the text, but
-
Hi I need to move the Purchase Requistion, data from legacy to Oracle I found the interface table "PO_REQUISITIONS_INTERFACE" for Requistions, There is oracle Concurrent program also to move the data from the interface table, i am interested to know