Running horribly (stop errors installing XP or 2003)

P4 3.2GHz, HT enabled
Kingston DDR400 3-3-3 unbuffered non ecc
865PE Neo2-FIS2R
MSI FX5950 ultra 256mb no OC
Antec Trueblue 480W
Maxtor 80GB IDE on ata100
Samsung 120GB IDE on onboard promise ata133
Maxtor 250GB sata on the promise controller
BIOS - mostly default settings... need help here too
trying to install WinXP + SP1
my problem:
if i disable EVERYTHING including the l1 l2 cache and leave HT enabled, i can get xp to install VERY slowly.
if i enable l1 l2 cache, i get the bsod stop errors 'IRQL not less or equal'
so for now its installing VERY slowly.
i'm hoping to get XP installed so i can at least update all drivers and everything.
this is not easy for me.
can anyone give me a helping hand at configuring this system properly? basically what i need is for someone to go through with me what my bios settings should be so that the system runs properly.
i've built 6 systems and never had issues like this before. thanks in advance, and i apologize for my 'noobism'

Quote
Originally posted by REILLY875
Why do you have the Samsung 120 on the Promise controller?.....I would take it of that (IDE-3) as any performance that you may think you would get with the 133, will be wiped by the Fact that you will be jamming up the south-bridge, as that is the bus where the Promise Chip resides ...So IDE-2 ATA-100 would be a better place for that HDD.....As for your BIOS, I believe this is where your troubles lie....You are using Both P-ATA+S-ATA.....You have to go into "On-Chip IDE Configure" to make sure that you have it set the way you need.....By the way, which HDD are you putting WINDOWS on?.............Sean REILLY875
hey thanks for the quick reply!
i'll try moving the samsung to the ata 100.
right now its finally installing windows 2003. its taking a ridiculously long time. says 26 minutes left. it takes 30 minutes for every one minute to go by :(
i'm trying to install windows on the maxtor 80gb drive on the ata100 up top.
how should i configure bios for the one sata drive on the promise controller? i'm a newb with all this new technology.
my plan is to have my music archive on the 250gb drive, developmental stuff on the 120 (web/graphic design, video editing), and windows with apps and games installed on the 80gb
so basically i'm asking this:
where should i plug each drive?
i have 80gb as master of IDE2 (blue one) and i'll move the samsung to slave of ide2
i have my 2 cd roms set on the IDE1 (pioneer dvd master, mitsumi 54x burner slave)
and then the 250gb sata is on SATA4 right now. where should it be?
also, bios settings. as you said i have to set stuff up in ide config, what values should i have there?
and for memory timing and all that... should i leave it default?
and why am i getting stop errors with l1 l2 cache enabled?
thanks a lot again in adavance. i hope you can answer these ones now

Similar Messages

Windows 7 64bit STOP Error Code 0x000000F4

Hello, I got a BSOD when my computer was almost idle (only utorrent was running) with stop error code 0x000000F4.
Also at the blue screen it got stuck at the 2nd step (don't remember what it says) and as a result I don't have a minidump file.
My pc specs are:
Motherboard: ASUS Rampage III Extreme
CPU: Intel i7 - 950 @ 3,00GHz
RAM: 3x2GB @ 1866MHz
Windows Drive: 60GB SSD (OCZ Agility)
OS: Windows 7 Ultimate Sp1 64bit
This has happened quite a few times during the 1 year I have this computer. The previous times the SSD I had (Corsair F60) stopped working. (2 SSDs dead)
The problem is that I cannot reproduce the problem so that we find out the cause. Is it something with the controller of the motherboard? What should I do?
Thank you for your time!

* Bugcheck Analysis *
CRITICAL_OBJECT_TERMINATION (f4)
A process or thread crucial to system operation has unexpectedly exited or been
terminated.
Several processes and threads are necessary for the operation of the
system; when they are terminated (for any reason), the system can no
longer function.
Arguments:
Arg1: 0000000000000003, Process
Arg2: fffffa800a74ab30, Terminating object
Arg3: fffffa800a74ae10, Process image file name
Arg4: fffff8000339f8b0, Explanatory message (ascii)
Debugging Details:
PROCESS_OBJECT: fffffa800a74ab30
IMAGE_NAME: csrss.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 0
MODULE_NAME: csrss
FAULTING_MODULE: 0000000000000000
PROCESS_NAME: csrss.exe
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
BUGCHECK_STR: 0xF4_C0000005
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
CURRENT_IRQL: 0
STACK_TEXT:
fffff880`0c7d60e8 fffff800`034265e2 : 00000000`000000f4 00000000`00000003 fffffa80`0a74ab30 fffffa80`0a74ae10 : nt!KeBugCheckEx
fffff880`0c7d60f0 fffff800`033d399b : ffffffff`ffffffff fffffa80`0be7ab60 fffffa80`0a74ab30 fffffa80`0a74ab30 : nt!PspCatchCriticalBreak+0x92
fffff880`0c7d6130 fffff800`03353448 : ffffffff`ffffffff 00000000`00000001 fffffa80`0a74ab30 00000000`00000008 : nt! ?? ::NNGAKEGL::`string'+0x176d6
fffff880`0c7d6180 fffff800`0309aed3 : fffffa80`0a74ab30 fffff800`c0000005 fffffa80`0be7ab60 00000000`04040a40 : nt!NtTerminateProcess+0xf4
fffff880`0c7d6200 fffff800`03097470 : fffff800`030e767f fffff880`0c7d6b78 fffff880`0c7d68d0 fffff880`0c7d6c20 : nt!KiSystemServiceCopyEnd+0x13
fffff880`0c7d6398 fffff800`030e767f : fffff880`0c7d6b78 fffff880`0c7d68d0 fffff880`0c7d6c20 00000000`04041600 : nt!KiServiceLinkage
fffff880`0c7d63a0 fffff800`0309b2c2 : fffff880`0c7d6b78 00000000`778d8f36 fffff880`0c7d6c20 00000000`040410d8 : nt! ?? ::FNODOBFM::`string'+0x49874
fffff880`0c7d6a40 fffff800`03099e3a : 00000000`00000001 00000000`04040ff8 00000000`00000001 00000000`778d8f36 : nt!KiExceptionDispatch+0xc2
fffff880`0c7d6c20 00000000`778e9a9d : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiPageFault+0x23a
00000000`04041000 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x778e9a9d
STACK_COMMAND: kb
FOLLOWUP_NAME: MachineOwner
FAILURE_BUCKET_ID: X64_0xF4_C0000005_IMAGE_csrss.exe
BUCKET_ID: X64_0xF4_C0000005_IMAGE_csrss.exe
Followup: MachineOwner
Bug Check Code 0xF4: http://msdn.microsoft.com/en-us/library/ff560372(VS.85).aspx
The BSOD occured when csrss.exe was running. Have
a look to that: http://www.ehow.com/how_2104293_solve-csrssexe-problem.html
Please disable all security softwares you are using and check again.
If this does not help, zip memory dump MEMORY.DMP under c:\windows\ and upload it.
This
posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
Microsoft Student
Partner 2010 / 2011
Microsoft Certified
Professional
Microsoft Certified
Systems Administrator: Security
Microsoft Certified
Systems Engineer: Security
Microsoft Certified
Technology Specialist: Windows Server 2008 Active Directory, Configuration
Microsoft Certified
Technology Specialist: Windows Server 2008 Network Infrastructure, Configuration
Microsoft Certified
Technology Specialist: Windows Server 2008 Applications Infrastructure, Configuration
Microsoft
Certified Technology Specialist: Windows 7, Configuring
Microsoft
Certified Technology Specialist: Designing and Providing Volume Licensing Solutions to Large Organizations
Microsoft Certified
IT Professional: Enterprise Administrator
Microsoft Certified IT Professional: Server Administrator
Microsoft Certified Trainer

Blue screen error while trying to install windows server 2003 in Lenovo G500s essentials Notebook

Hi,
I bought a new lenovo G500s essentials note book. It's a freedos system. I am trying to install windows server 2003 in it. But I am getting blue screen error . error message like ths,
Technical Information:
STOP: 0*0000007B (0*FFFFFADF2CE323C0, 0*FFFFFFFFC0000034, 0*0000000000000000, 0*0000000000000000)
Can someone please help.
Regards,
Priya.
Solved!
Go to Solution.

I don't have a similar machine to look at so this is a bit of a guess:
Per page 30 or your user's guide http://download.lenovo.com/consumer/mobiles_pub/lenovo_g400sg400stouchg500sg500stouchg405sg505s_ug_e...:
How can I start the BIOS setup utility?
To start the BIOS setup utility:
1 Shut down the computer.
2 Press the Novo button and then select BIOS Setup
There should be a tab labelled something like "Configuration" and on that page something like "SATA controller mode". Select "compatible" and save and exit.
I'm not certain this will fix your problem, but it's worth a try.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Every time I sign into my Macbook, I get an error message from Automator; "The data couldn't be read because it has been corrupted.". I have never created an Automator workflow. How do I find out what Automator is trying to run and stop it?

Every time I sign into my Macbook, I get an error message from Automator; "The data couldn't be read because it has been corrupted.". I have never created an Automator workflow. How do I find out what Automator is trying to run and stop it?

Maybe it's set as a login item:
- System Preferences: Users and Groups:
- Highlight your user account in the left pane/list
- Click "Login" tab at the top.
See if you have an Automater action on the list
- Note, you can select it, then right-click, and can then select "Reveal in Finder". That way you might have an idea what installed it.

Error When Finish the Install on Windows 2003

When finish the install on Windows 2003 Server the last check list Oracle Audit Vault Asistant send error:
avca.bat initialize_av -crtscma N -avsysdba ${s_avsysdba} -avadm ${s_avadm} ${s_avauditor} -dvowner ${s_dvownerarg} ${s_dvacctmgr} -jdbc_str jdbc:oracle:oci:@av -dbalias av -sid av -avconsoleport 5700
dont run command.
which i can do. thanks for the help

Hi, Pankaj,
i encountered same problem as you did.
please could you elaborate how you resolve the problem "by passing oracle_sid at cmmond prompt and then starting the database, before that check listner is running or not , if not start listner"
many thanks,
lee

Error Installing EBS R12 - Win 2003 Server Standard R2

Hi Experts,
This is my 8th try to install EBS R12 and got same error.
OS - Win 2003 Server Standard R2.
used CYGWIN, MS Visual C++ 2010 and Strawberry Perl.
Used Oracle E-Business Suite R12 Installation Steps on Windows XP followed all steps......finally same error......
http://www.mediafire.com/?najx7zk8zl780x8
in the above link I added all th screen shots and some logfiles.
1. Can I use MS Visual C++ 2010??
2. Can I use Strawberry Perl?
Can any one please help me........Please let me know if you need any additional info or any other log files........
Thanks,
DK

1. Can I use MS Visual C++ 2010??You can use either Microsoft Visuall Studio 2005/2008 only.
Oracle E-Business Suite Installation and Upgrade Notes Release 12 (12.1.1) for Microsoft Windows Server (32-bit) [ID 761567.1]
MS Visual Studio 2008 and Visual C++ 2008 Express for Oracle E-Business Suite Release 12 on Windows [ID 1070674.1]
2. Can I use Strawberry Perl?Yes, as long as you installed the required version (or above).
Can any one please help me........Please let me know if you need any additional info or any other log files........I have checked the log files and I see that you get the same error you had in your other thread. Were you able to run md5sum to verify the integrity of the stage area directory?
Thanks,
Hussein

Am unable to install CS5 on mac running yosemite. Tried installing JavaFor OSX, it still doesn't work. Error message reads "inconsistency in the installer database"

Am unable to install CS5 on mac running yosemite. Tried installing JavaFor OSX, it still doesn't work. Error message reads "inconsistency in the installer database"

remove your caps database. this shows the location for cs3. make the obvious changes for cs5.
Error "...Installer Database is Corrupt..." when you install Adobe Creative Suite 3 products

Stop error on Q180 when trying to install windows 7 professional

I get the stop error 0x0000007E when i try to start to install windows 7 pro (64-bit), it goes through 2 "windows is loading files" screens after I select the usb drive to boot from.
The usb drive was formatted and the image copied onto using the Windows 7 USB Tool.
If anyone can assist it would be greatly appreciated, so far loving the little guy just need windows pro on it for work.

were did you get the iso image from dvd or download?
if dvd you might need to rip it again if download use http://www.askvg.com/direct-download-links-download-official-original-and-untouched-windows-7-iso-32...
Thx dave
yoga 2, lenovo b540
3 custom gaming pc systems

Show-stopping error when I try to load/run the muse code with JQuery version 1.9.1.

Version 1.9.1, and the muse code uses 1.8.3. As you can see HERE,http://jquery.com/download/ version 1.9.0 was a major milestone release for JQuery that eliminated much of the (deprecated) functionality of earlier versions. Unfortunately, the muse html uses some of that deprecated functionality (specifically, the "browser( )" function HERE)http://jquery.com/upgrade-guide/1.9/#jquery-browser-removed. Thus I am getting a show-stopping error when I try to load/run the muse code with version 1.9.1. Other people have had this same problem (see THIS)http://bugs.jquery.com/ticket/13214.
Do you see an update in the near future?

Version 1.9.1, and the muse code uses 1.8.3. As you can see HERE,http://jquery.com/download/ version 1.9.0 was a major milestone release for JQuery that eliminated much of the (deprecated) functionality of earlier versions. Unfortunately, the muse html uses some of that deprecated functionality (specifically, the "browser( )" function HERE)http://jquery.com/upgrade-guide/1.9/#jquery-browser-removed. Thus I am getting a show-stopping error when I try to load/run the muse code with version 1.9.1. Other people have had this same problem (see THIS)http://bugs.jquery.com/ticket/13214.
Do you see an update in the near future?

After Mountain Lion install, my MacBook Pro's fan is running non-stop.

After Mountain Lion install, my MacBook Pro's fan is running non-stop and you can hear the insides working extra hard. Is this normal? It's very loud and annoying?

http://support.apple.com/kb/HT3964?viewlocale=en_US

I'm running OS 10.4 and purchased Mac Box Set with Snow Leopard. When I run the Snow Leo install it errors saying I need OS 10.5 to run the install. How do I get around this? I've read that it's possible to go direcectly from 10.4 to 10.6.

I'm running OS 10.4 and purchased Mac Box Set with Snow Leopard. When I run the Snow Leo install it errors saying I need OS 10.5 to run the install. How do I get around this? I've read that it's possible to go direcectly from 10.4 to 10.6.

To buy a hard drive try Newegg.com http://www.newegg.com/Store/SubCategory.aspx?SubCategory=380&name=Laptop-Hard-Dr ives or OWC http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/
Here's a cheap SATA external hard drive case on eBay http://cgi.ebay.com/USB-2-5-SATA-HDD-HARD-DRIVE-EXTERNAL-ENCLOSURE-CASE-BOX-/120 636286623?pt=PCC_Drives_Storage_Internal&hash=item1c167ba69f
Here's instructions on replacing the hard drive http://creativemac.digitalmedianet.com/articles/viewarticle.jsp?id=45088

WRT160N Installed - Now Receiving Stop Error

I just installed the WRT160N. Everything seemed to install correctly, my new wireless even showed up in my list of wireless connections, then I was hit with the blue screen of death. It's a stop error: 0x0000000A. Now I only have internet access directly from modem to computer. As soon as I turn the wireless option on my laptop "ON" I get the blue screen again and have to restart. I think I've remove all unnecessary hardware and software, but it's still not working. I can't even turn on the wireless option. Can anyone help me?

Delete and de install you wireless adapter. Download the newest drivers and re install the adapter.

Can an error in battery cause a slow CPUS and the fan to run non-stop?

tthe battery need serviced but my computer runs slow and the fan is running non-stop. MacBook Pro 13" purchased around 2011.

OK, you really need to dump that Windows attitude quickly, because what worked over there is completely useless here. I never understood the "upgrade didn't work obviously, because this or that happened, so how do I downgrade." I hang out around here, and I haven't seen many comments about fans running full blast after the updates. I did them, and nothing happened.
First, you can't downgrade the firmware EFI update. I think if you tried, it would brick your MBP.
You could reinstall Lion if you wanted, but that's really a pain, and once again, one of those Windows things that people always do that wastes time. A security update and Remote Desktop Client (which only runs if you start it up) would not effect your fan speed.
Apple does have "restore points", but it's a real backup system that requires a backup drive. It's called Time Machine and it's preinstalled on your Mac, easy to use, and allows you to go as far back in time on your Mac as the size of your backup drive will allow.
Now, after all that, let's try to figure out what's going on with your fans. First, did you do the EFI update correctly? Meaning did you do it when the MBP was actually plugged into the wall? What are you running? Games? Videos? Something else?

PLEASE: IS THIS A VALID ERROR WHEN RUNNING DISC ULTIL FROM INSTALL DISK 1

when running disc util from install disc 1..i'm getting "invaild leaf record count it should be 7 instead of 96" my install reads os vers 10.2.1.. my current os is 10.4.9

I would try running the Disk repair several more times. But more then likely you'll need a more robust utility.
DiskWarrior is the best there is at this.
If you have a backup, preferably a bootable backup from before this problem, you can Erase and Install to give you a new directory. If you don't have a backup, this procedure will erase everything on your drive.
Cheers!
DALE

Error Installing Oracle SOA Suite 10.1.3.1

Hi Gurus,
I was in the process of installing Oracle SOA suite 10.1.3.1 on Windows 2003, the installer seemed to take a lot of time at the 92% point, a closer examination that was the point at which the opmnctl was starting the services. After that, the installer proceeds to conclude the setup successfully but the opmn log indicates an error as shown below
==================================================================================================
09/03/09 18:26:51 [ons-internal] ONS server initiated
09/03/09 18:26:51 [pm-internal] Create pm state directory: C:\product\10.1.3.1\OracleAS_1\opmn\logs\states
09/03/09 18:26:51 [pm-internal] PM state file does not exist: C:\product\10.1.3.1\OracleAS_1\opmn\logs\states\.opmndat
09/03/09 18:26:51 [pm-internal] OPMN server ready. Request handling enabled.
09/03/09 18:26:56 [pm-requests] Request 2 Started. Command: /start
09/03/09 18:26:56 [pm-process] Starting Process: HTTP_Server~HTTP_Server~HTTP_Server~1 (1600851961:0)
09/03/09 18:26:56 [pm-process] Starting Process: default_group~home~default_group~1 (1600851962:0)
09/03/09 18:26:59 [pm-process] Process Alive: HTTP_Server~HTTP_Server~HTTP_Server~1 (1600851961:1548)
09/03/09 18:36:57 [pm-requests] Request 2 Completed. Command: /start
09/03/09 18:36:57 [pm-process] Stopping Process: default_group~home~default_group~1 (1600851962:2016)
*09/03/09 18:36:57 [libopmnoc4j] Process Stop Error: default_group~home~default_group~1 (1600851962:2016)*
*09/03/09 18:36:57 [libopmnoc4j] Failed to construct stop command for proc: 1600851962*
*09/03/09 18:36:57 [libopmnoc4j] Forcefully Terminating Process: default_group~home~default_group~1 (1600851962:2016)*
==================================================================================================
The installer then indicates that the setup is successful despite the OPMN error. After the setup however, the Application server configuration assistant and the OPMN configuration assistant fail with the errors below:
==================================================================================================
Launched configuration assistant 'Oracle Application Server Configuration Assistant'
Tool type is: Optional.
The command being spawned is: 'C:\product\10.1.3.1\OracleAS_1\jdk\bin\java -cp C:\product\10.1.3.1\OracleAS_1\j2ee\home\applications\ascontrol\ascontrol\WEB-INF\lib\ascontrol.jar;C:\product\10.1.3.1\OracleAS_1\j2ee\home\applications\ascontrol\ascontrol\WEB-INF\lib\log4j-core.jar;C:\product\10.1.3.1\OracleAS_1\jlib\oraclepki.jar;C:\product\10.1.3.1\OracleAS_1\jlib\ojmisc.jar; oracle.sysman.ias.studio.installer.ASControlConfigAssistant -sso false -j2eeinstance home -username oc4jadmin -password Protected value, not to be logged -oraclehome C:\product\10.1.3.1\OracleAS_1'
Start output from spawned process:
java.lang.NoClassDefFoundError: oracle/sysman/ias/studio/installer/ASControlConfigAssistant
Exception in thread "main"
End output from spawned process.
Configuration assistant "Oracle Application Server Configuration Assistant" failed
java.lang.NoClassDefFoundError: oracle/sysman/ias/studio/installer/ASControlConfigAssistant
Exception in thread "main"
Result code for launching of configuration assistant is: 1
Launched configuration assistant 'Oracle Process Management and Notification Configuration Assistant'
Tool type is: Recommended.
The command being spawned is: 'C:\\product\\10.1.3.1\\OracleAS_1\\perl\\5.8.3\\bin\\MSWin32-x86-multi-thread\\perl.exe C:\product\10.1.3.1\OracleAS_1\config\launchopmnCA.pl'
Start output from spawned process:
C:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl.exe start stopproc reload startproc
Launching C:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl.exe start
opmnctl: opmn already running
start status 0
Launching C:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl.exe stopproc
opmnctl: stopping opmn managed processes...
stopproc status 0
Launching C:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl.exe reload
opmnctl: reconfiguring opmn...
opmnctl: opmn reloaded successfully.
reload status 0
Launching C:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl.exe startproc
opmnctl: starting opmn managed processes...
================================================================================
opmn id=harbel_srv:6200
1 of 2 processes started.
ias-instance id=brnhb.harbel_srv.lbdi.com
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
ias-component/process-type/process-set:
default_group/home/default_group/
Error
--> Process (index=1,uid=983174492,pid=1016)
time out while waiting for a managed process to start
Log:
C:\product\10.1.3.1\OracleAS_1\opmn\logs\\default_group~home~default_group~1.log
start status 152
opmn not reloaded and restarted
End output from spawned process.
Configuration assistant "Oracle Process Management and Notification Configuration Assistant" failed
=================================================================================================
I have not been able to establish the cause of this problem, any help will be greatly appreciated.
Edwin

I have tried that option but the result was the same, however, I realized that there was a .err file among the installation logs and below are the contents:
===============================================================================================
java.util.zip.ZipException: oversubscribed dynamic bit lengths tree
     at java.util.zip.InflaterInputStream.read(Unknown Source)
     at java.util.zip.ZipInputStream.read(Unknown Source)
     at java.io.FilterInputStream.read(Unknown Source)
     at oracle.sysman.oii.oiix.OiixFileOps.copyStream(OiixFileOps.java:1201)
     at oracle.sysman.oii.oiij.OiijFastJarExtracter.copyFileFromJar(OiijFastJarExtracter.java:217)
     at oracle.sysman.oii.oiij.OiijFastJarExtracter.copyJarContents(OiijFastJarExtracter.java:170)
     at oracle.sysman.oii.oiij.OiijFastJarExtracter.extract(OiijFastJarExtracter.java:123)
     at oracle.sysman.oii.oiij.OiijJarExtractQueue$OiijJarExtractWorker.run(OiijJarExtractQueue.java:338)
java.util.zip.ZipException: oversubscribed dynamic bit lengths tree
     at java.util.zip.InflaterInputStream.read(Unknown Source)
     at java.util.zip.ZipInputStream.read(Unknown Source)
     at java.util.zip.ZipInputStream.closeEntry(Unknown Source)
     at oracle.sysman.oii.oiij.OiijFastJarExtracter.copyJarContents(OiijFastJarExtracter.java:173)
     at oracle.sysman.oii.oiij.OiijFastJarExtracter.extract(OiijFastJarExtracter.java:123)
     at oracle.sysman.oii.oiij.OiijJarExtractQueue$OiijJarExtractWorker.run(OiijJarExtractQueue.java:338)
Oracle JAAS [Tue Mar 10 12:16:26 GMT 2009] admin password is changed successfully
opmnctl: starting opmn and all managed processes...
============================================================================
I don't know whether this could have something to do with the error.
Regards,
Edwin

Running horribly (stop errors installing XP or 2003)

Similar Messages

Maybe you are looking for