Running two SSIDs, one with WPA2 and one with WEP

Hi,
I have a WRT610N.
How isolated are the two SSIDs that I can run?
I know one is running at 5GHz and the other at 2.4GHz. I've given each an SSID and a different security policy: I run "sensitive" stuff under WPA2, and I run the other for legacy hardware that supports only WEP (eg my son's Nintento DS).
But are these two keys to the same house, so to speak? If someone cracks my WEP network, can they access the machines on the WPA network? Or are they completely isolated?
Does this make sense?
Thanks for any enlightenment.
-- Mike
Solved!
Go to Solution.

Yes, they are "two keys to the same house". The "house" is your LAN. If someone cracks your WEP, and wirelessly breaks into your router, then they have access to your LAN. This would be like allowing a hacker to wire his computer directly to your router. Being on your LAN, puts the hacker in a very good position to break into any other computer on your network. Your WPA2 encryption does not give you any protection from someone who is already on your LAN.
The solution to your problem is to run two separate wireless routers:
modem ---- router1 --- router2
router1 is set to "Local IP address" 192.168.1.1 , WEP encryption , set "AP isolation" to "enabled" , (note: no printers on router1)
router2 is set to "Local IP address" 192.168.2.1 , WPA2 encryption, use a strong password (and not anything similar to the WEP password).
modem is wired to Internet port of router1
LAN port of router1 is wired to Internet port of router2
The wireless 2.4 GHz channels on the two routers must be different, and are preferably at least 5 channels apart. Usually channels 1, 6, or 11 work best.
With the above two router setup, the Internet port of router2 should protect you from any intruders on router1.

Similar Messages

Aironet - Two SSIDs, One with WPA, One Without

I have an AP that I want to have two SSIDs on, let's say, "Admin" and "User."
The User SSID should be wide open, unsecure, etc.
The Admin SSID, should not be broadcasted, and be protected via a passwrd, preferably WPA pre-shared key.
Is this possible? If so, how?
So far I have both SSIDs working, in an open/unsecure mode. My VLANs are working great, and when I tried the suggestion in the help, it looks like it turned on WPA, but now I cannot see the SSID for Admin.
If you need a copy of the config, let me know.
Thanks,
Anthony

version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$zH.z$lhh9AqT3HXXU2WxXSd2f20
ip subnet-zero
no aaa new-model
dot11 ssid faculty
vlan 100
authentication open
dot11 ssid students
vlan 400
authentication open
guest-mode
username x password x
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid faculty
ssid students
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
antenna receive right
antenna transmit right
interface Dot11Radio0.100
encapsulation dot1Q 100
no ip route-cache
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
bridge-group 100 spanning-disabled
interface Dot11Radio0.400
encapsulation dot1Q 400 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
ssid students
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio1.400
encapsulation dot1Q 400 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.100
encapsulation dot1Q 100
no ip route-cache
bridge-group 100
no bridge-group 100 source-learning
bridge-group 100 spanning-disabled
interface FastEthernet0.400
encapsulation dot1Q 400 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
transport preferred all
transport output all
line vty 0 4
login local
transport preferred all
transport input all
transport output all
line vty 5 15
login
transport preferred all
transport input all
transport output all
end

Two SSIDs one ACS

Hello,
how do I authenticate two SSIDs against one ACS. Users from SSID A should not be able to log onto SSID B and the other way around.
The proble here seems to be that for the ACS both SSIDs are authenticated by the same NAC/WiSM/Source IP address. I already tried to do something via the CallerID (IP address ranges of both SSIDs are different) but it does not work. It seems that in this CID field wildcards like 192.168.115.* and 192.168.117.* are ignored?
Who know more?
Thanks.
--Joerg

Joerg,
Please check this link,
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807669af.shtml
Regards,
~JG
Do rate helpful posts

How do I run two Apple IDs with one computer and sync music content?

I have a single PC which I have added all of the music to one my log in. My wife and I have Iphones and I want to run separate accounts for itunes, but sync music content from the single source to both phones. Whenever I have tried to do this in the past, it starts to sync all app to both phones. I tried to therefore have separate log ins on the pc itself, but when I have tried this, the music content does not update on my wifes itunes library, after I have added music to mine (ie imported a CD), even though I have linked my wife's music library for itunes purposes to my music folder (hopefully that makes sense!!). Can anyone help as this is driving me mad, otherwise I will just have to run from my account and delete all of my wifes apps etc whenever I sync my phone, and vice versa.
Thanks!!!
Jeremy

Is the following document of any help with that?
[How to use multiple iPods with one computer|http://support.apple.com/kb/HT1495]

How do I run two sub-VIs in parallel and have the faster VI continue to execute while the slower one completes?

I have two sub-VI's - one that makes a laser distance measuring device turn on and return a distance, and another that moves a platform upon which a target is mounted that the laser reflects against. The laser VI takes well under 5 seconds to complet. The platform-moving VI, on the other hand, requires about 30 second. I would like to be able to have the laser on AS the platform moves. Of course, I can accomplish this by running the VIs seperately. However, I would like to control them from a master VI. Currently, the laser turns on as the platform begins to move but then turns off, since the master VI waits on the platform-moving VI to
complete. Any help with this seemingly simple dilemma would be greatly appreciated.

In order to synchronize the two VI's I would recommend using a global variable. By creating a global boolean, you can make reference to it in both programs, and control when your "laser" subVI terminates.
Basically, have your "laser" subVI wait until the global boolean goes true to stop execution. Have the boolean initialized false, and then have your "platform" subVI write a true to the global boolean when it has finished running. This will keep you laser running until the platform has completed its move. Good luck!

Can I run two separate ITune Accounts & Libraries and ipods on one computer

I have a friend visiting for a month and they want to use their IPod Nano and ITunes account on my computer. i.e. purchase and download their own songs via Itunes, sync with their Ipod etc. the same way they would on their own home computer, while they are here.
I already have Itunes installed on my computer for my own IPod Shuffle, and related account for buying music etc. and want to continue to sync my Ipod through my own account of course
Is there a way I can have both of these Ipods functioning fully with separate Itune accounts and libraries on my computer? How do I do this?
Thanks for any help you can provide.

OK.... I've ran into a problem and don't know how to proceed with this.
The 2nd user is set up with their ITunes account and we have successfully purchased a few songs.
What I expected to do was sync their Ipod and have the songs already on their IPod copy into the "new" Library we just set up. However, indications are that if I use "sync", it will erase the songs presently on the IPod and then only put back the few new songs we just purchased. (I tried a few other things but cannot get the songs from the IPOD into the ITunes Library or any other folder to preserve them)
1. If it is even possible, how do I get the songs off the IPod into the newly established Library?
2. If I indeed cannot sync the IPOD / Library - how do I get the newly purchased songs from the Library to the IPOD without erasing the songs already on the Ipod.
Thanks, hope you can help!

Can you run two Ipods, one older, one newer, on the same version of Itunes?

I have a second generation Ipod Shuffle, and I have a fourth generation 40gb Ipod. When I installed the Shuffle, I had to upgrade my Itunes. Now it won't recognize my older Ipod at all. I plug it in, and it doesn't do anything. The shuffle works fine, but nothing doing on the larger, older Ipod. Is there anything I can do?

Start with these articles and see if that gets you anywhere...
iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
http://docs.info.apple.com/article.html?artnum=305136
iTunes for Windows: iTunes 7 doesn't recognize iPod
http://docs.info.apple.com/article.html?artnum=304434
iPod missing in "My Computer" or in iTunes for Windows
http://docs.info.apple.com/article.html?artnum=61711
Also you might try forcing the iPod into disk mode first, then connecting it to your computer and see if that makes it show up in iTunes...
Putting iPod into Disk Mode
http://docs.info.apple.com/article.html?artnum=93651
Windows confuses iPod with network drive or hard drive and may keep iPod from mounting or songs may seem to disappear
http://support.apple.com/kb/TS1493
Cheers,
Patrick

Run two counters simultaneously with out affecting each other

Hi
I am new to labview. I am trying to figure out how the two counters/ timers( one is nongateable standard timer and another is standard timer which is software based) run simultaneously. I created it in different while loops. Is it possible to create two counters in single loop with out affecting each other?

Hi Pavani,
Welcome to the forums! As a new LabVIEW user there are many helpful resources out there to get you started. I would like to point you to the two links in my signature. The first is a six hour LabVIEW course and the second helps you learn DAQmx. Also take advantage of the shipping examples. When you open LabVIEW select Find Examples to open the Example Finder. Assuming you are using DAQmx, you can go to Hardware Input and Output>>DAQmx>>Counter Measurements and find many useful example programs that either do what you want or can be modified to perform the task you desire.
To answer you question, two counters in the same loop do not affect each other. The counters will gather data separately. By putting them in the same loop, you just perform the reads in software at the same time.
Regards,
Ima
Applications Engineer
National Instruments
LabVIEW Introduction Course - Six Hours
Getting Started with NI-DAQmx

Two ssids in one Dot11Radio interface

Hello,
Whilst configuring CISCO867-W router I have encoutered the following problem.
On built-in access point I have one Dot11Radio interface. Is it possible to have two ssids associated with two different vlans on one interface? If yes, how to do it? If no, is there any solution to have two separated wlans on an access-point with one Dot11Radio?

Of course you can have two wlans associated with two different vlans on the same radio interface.
Here is a simple example on how to it?
on the router the most important thing you have to make sure that the interface
Wlan-GigabitEthernet0 is configured as trunk and allowing the vlans mapped on the ssids defined under the radio interface of the embedded AP. Also you have to make sure that dhcp pools have been defined for both vlans.
Assuming that you have two ssids:
ssid1 & ssid2 mapped to vlans 1 and 2 consecutively. vlan 1 has been defined as the native on the trunk defined on
Wlan-GigabitEthernet0
AP(config)#dot11 ssid ssid1
                #authentication open
                #vlan 1
               #exit
AP(config)#dot11 ssid ssid2
               #authentication open
               #vlan 2
               #exit
AP(config)#interface dot11radio 0
              #ssid ssid1
              #ssid ssid2
              # no shut
              # exit
AP(config)#int dot11radio 0.1
               #encapsulation dot1q 1 native
               #bridge-group 1
               #exit
AP(config)#int dot11radio 0.2
               #encapsulation dot1q 2
               #bridge-group 2
               #exit
AP(config)#int gig 0.1
               #encapsulation dot1q 1 native
               #bridge-group 1
               #exit
AP(config)#int gig 0.2
               #encapsulation dot1q 2
               #bridge-group 2
               #exit
Please Don't forget to mark the question as answered once having the right response

[WRV200] Two SSID and remote control?

Hi,
I have a WRV200 and need to setup a wifi access for a place that is shared. So two questions:
1. How can I have two SSIDs, one for me, one for visitors with my router? Is it by setting up a VLAN ?
If yes, would those persons be able to access the Internet using a separate WPA2 key?
2. I will need to remotely configure that shared wifi by replacing the WAP key now and then, not the
main key for my private access, only the one for visitors. Is it possible to remotely connect to my
router (dynamic IP address, not static) and configure it remotely so each time a new visitor shows
up, I can change her/his WPA2 key ?
If yes, what do I need? Some kind of OpenDNS service?
The idea is for a house that is rented during vacation time. Each time a new visitor would show up,
I'd have to set a new key so the renter can access the Internet for the rental time, and then change
the key remotely to disable access until the next visitor.
Thanks for any clarification.
Steve

Hi Steve,
Yep I have to admit I have for some time personally used DynamicDNS because I am too thrifty to buy a fixed IP.
I guess for the silly reason Dyndns was the first in the list of choices in the management gui. .
Next time you buy a Small Business Wireless Router, move away from the End of Life WRV200 product have a look at the new RV120W or RV220W wireless routers,
But the older WRV200 allow for remote management, if you know it's IP address or domain name (via DYNDNS or TZO).
Have fun.
regards Dave

Running 17" MacBook Pro with 10.6.8 and 10.9.4, but recently unable to star up on 10.6.8 please help.

I have a 17" mid 2010 macbook pro .
I have been running two partitions one with Mavericks 10.9.4 and one with snow leopard 10.6.8.
I have recently lost the ability to startup on the snow leopard partition.
When booted to mavericks all seem to be fine with files on the snow leopard partition.

Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

Can a mac mini be set up to run two separate users at the same time?

I work for a middle school and we need to purchase 20 computers that will just be used to run internet apps. Though we have all Macs, we don't have a big budget and for this one use only, we are condsidering purchasing inexpensive HP all-in-ones for about $450 each. However, I was wondering if a Mac Mini can be first set up with 2 partitions, install the OS on both partitions, then run two different users, with two separate monitors and keyboards, at the same time? This way, instead of purchasing 20 Windows computers, we could purchase 10 Mac Mini's (and displays) and save money, and still be supporting just one OS throughout the campus.

If you setup a server, as in the Mac OS X Server Installation, pages 23ff show configurations, you can have multiple users, but they must all have computers. Some installations can be done with dumb terminals but that is not what you seem to want. Unix machines do have a multiple simultaneous user capability but you still have to have a computer for each user, again, not what you seem to want to do. Right now there are two other users logged in on my Sun workstation on the desk behind me...they are logged in because I permit them to do so.
And last night for an experiment I connected my iMac and MBP by ethernet wire, logged in on the iMac, then logged in on the MBP and from there on the iMac...but I set up the network to permit that and then disabled it again. You can create security holes doing things like this.
As dwb points out switching from Apple to PC equipment is a false economy that lures in administrators. In our county school system we had a superintendent who hired a good friend...who had PC-industry ties. Decided to remove all Apple equipment from the elementary schools and switch to PCs. It wasn't long before they ended up going on a 4-year cycle of "refreshing" the equipment, i.e., completely replacing all hardware in every school on a four year cycle. Since my wife was a Media Specialist, aka librarian, and responsible for technology in her school, every four years she had to develop a complete school map of where each teacher wanted the computers in their classrooms, complicated by where the technicians predetermined the locations of the network wire drops, of course. then teachers get shuffled over the summer and all the plans are for naught.
Anyway, there really isn't a solution to your problem except to buy a large number of computers and let each student use one and have them networked to a server, print server, printers, etc. This is not inexpensive and cutting corners will only cause headaches for you.

Recording two sync applications with CP4

I try to record two Windows applications (two executables) which interact each other : for example, from the application #1 I select a vehicule in a list and in the application #2 this vehicule is located on a map layer. One application is running on monitor 1 and the other is running on monitor 2 (dual monitors). I'd like to record a slide from the application #1 and then a slide of the result on the application #2. I can't manage to do it :
- If I run one instance of Captivate 4, I can only choose one application
- If I run two instances of Captivate 4 and if I choose application #1 for the first instance and application #2 for the second one, it doesn't work : when I run the second recording (click on the red point), nothing is recorded ...
A workaround would be to record the slides for application #1 in project #1 and then for application #2 in project #2, and then copying (to the right location) the slides of project #2 inside the project #1 but I think is not a "stylish" method ...
Thanks in advance for your advices !

Hi there
I might think you could accomplish this as follows:
Start the applications and start Captivate. Record the first application up to the point where it interacts with the second. Then end the recording in Captivate. In Captivate, elect to record more slides (which will be appended to the existing recording) then choose the second application to be recorded.
Cheers... Rick
Helpful and Handy Links
Captivate Wish Form/Bug Reporting Form
Adobe Certified Captivate Training
SorcerStone Blog
Captivate eBooks

How to run two programs with one PC and two monitors

Good Morning,
I have a requirement to run a parallel loop and update the progress in two monitors with one computer.
For ex: its a two test stage, the process and progress of the 1st stage needs to displayed in monitor1 and similarly for 2nd stage to monitor 2 with program running with one computer.Would it be possible to do that.
Thanks in advance

Hi Parker,
yes, it's possible. You also have properties to set windows to specific monitors...
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Two crashes: one OS crash with gray screen and loading bar- help? (Stuck overseas, so you guys are it!)

Hey everyone.
When firefox crashed last night, I figured it was just firefox being difficult, but when while using firefox my entire computer crashed this afternoon and rebooted with a gray screen, the spinny wait symbol, and a loading bar, I started to get concerned. After looking through console, I'm not sure what's caused it to crash like this so I'm hoping one of you bright people here can tell me what exactly happened. I'm running a mac book pro with 10.6.8, have no real addons on firefox aside from adblock plus, divx, memory restart, a french dictionary, and a skin I've been using forever and have also spoken to the developer in the past about. I'm also using Firefox 17.0.1. After trying to google some of the more unfamiliar/suspicious lines (mostly relating to launch agents), I typed into terminal the command to list all launch agents and received 3 replies naming adobe, divx, and google. I used terminal to delete them all just for safe measure (plus the adobe update window has been irritating me to no end so maybe it'll go away now, haha). I did three things when I tried to boot up again after the crash and the weird launch screen with loading bar came up: 1) I held down the power button again because a) the screen was weirding me out and b) I thought it got hung up again (bar seemed to stall for an unusually long time), 2) I tried to boot again and when the same gray screen came back I just figured I had no choice and had to sit through it. 3) when the bar was at about half way I pulled out my ethernet cord for safe measure in case something shady was going on. These three things are also reflected in the log below.
I currently live overseas and the nearest Apple store is over two hours away with no guarantee of a native english speaker working, so if anyone can let me know what caused the crash and if there's anything I can do about it, I would be extremely grateful. The following is my current console log in its entirety from today, including my attempted system update to see if that would improve things (which also resulted in a gray screen with loading bar later), and a really weird bit at the end that is also confusing (but possibly caused by me tinkering in terminal- not sure).
NAME is replacing my HD name, and my screen name here (caithris) has replaced my computer user name. NUMBER has replaced anything that looks like a serial number of some kind.
Thanks so much ahead of time-- please let me know if there's anything else I can share.
Mar 31 00:30:01 NAME newsyslog[9228]: logfile turned over
Mar 31 01:03:25 NAME firefox[8993]: Mozilla has caught an Obj-C exception [NSRangeException: *** -[NSCFArray objectAtIndex:]: index (1) beyond bounds (1)]
Mar 31 01:03:25 NAME [0x0-0x10010].org.mozilla.firefox[0]: 2013-03-31 01:03:25.193 firefox[8993:903] Mozilla has caught an Obj-C exception [NSRangeException: *** -[NSCFArray objectAtIndex:]: index (1) beyond bounds (1)]
Mar 31 01:04:06 NAME [0x0-0x10010].org.mozilla.firefox[0]: pure virtual method called
Mar 31 01:04:06 NAME [0x0-0x10010].org.mozilla.firefox[0]: terminate called without an active exception
Mar 31 01:04:20 NAME ReportCrash[9260]: Saved crash report for firefox[8993] version 17.0.1 (1712.11.28) to /Users/Caithris/Library/Logs/DiagnosticReports/firefox_2013-03-31-010420_NAME.c rash
Mar 31 01:05:35 NAME SubmitDiagInfo[9280]: Submitted crash report: /Users/Caithris/Library/Logs/DiagnosticReports/firefox_2013-03-31-010420_NAME.c rash
Mar 31 03:00:27 NAME loginwindow[31]: loginwindow SleepWakeCallback WILL sleep
Mar 31 03:00:28 NAME configd[13]: PMConnection IPConfiguration com.apple.powermanagement.applicationresponse.slowresponse 1120 ms
Mar 31 11:22:53 NAME configd[13]: Sleep: Success - AC 97 - Idle Sleep
Mar 31 11:22:53 NAME configd[13]: Wake: Success - AC 97 - OHC2
Mar 31 11:22:53 NAME configd[13]: Hibernate Statistics
Mar 31 11:22:53 NAME loginwindow[31]: loginwindow SleepWakeCallback will power on, Currenttime:3/31/2013 11:22:53.195 AM - Waketime:3/31/2013 11:22:43.930 AM = Deltatime:9.265338957
Mar 31 11:22:53 NAME loginwindow[31]: askForPasswordBuiltIn after makekey, Currenttime:3/31/2013 11:22:53.212 AM - Waketime:3/31/2013 11:22:43.930 AM = Deltatime:9.281565964
Mar 31 11:22:53 NAME loginwindow[31]: builtInAuthWindowBecameKey, Currenttime:3/31/2013 11:22:53.243 AM - Waketime:3/31/2013 11:22:43.930 AM = Deltatime:9.312892973
Mar 31 11:22:53 NAME configd[13]: network configuration changed.
Mar 31 11:22:54 NAME configd[13]: PMConnection AirPort configd plug-in com.apple.powermanagement.applicationresponse.slowresponse 9839 ms
Mar 31 11:22:54 NAME configd[13]: PMConnection IPConfiguration com.apple.powermanagement.applicationresponse.slowresponse 9849 ms
Mar 31 11:22:57 NAME configd[13]: network configuration changed.
Mar 31 11:22:57 NAME ntpd[20]: sendto(17.171.4.13) (fd=24): Network is unreachable
Mar 31 11:23:02 NAME loginwindow[31]: in pam_sm_authenticate(): Failed to determine Kerberos principal name.
Mar 31 11:23:02 NAME loginwindow[31]: builtInAuthWindowDidResignKey
Mar 31 11:23:02 NAME loginwindow[31]: handleUnlockResult, Currenttime:3/31/2013 11:23:02.536 AM - Waketime:3/31/2013 11:22:43.930 AM = Deltatime:18.606058955
Mar 31 11:23:32 NAME loginwindow[31]: no spins reported for this wake
Mar 31 11:27:31 NAME SubmitDiagInfo[9444]: Cleaning up expired diagnostic messages database at path: /var/log/DiagnosticMessages/2013.03.01.asl
Mar 31 11:33:29 NAME [0x0-0x3b63b6].org.mozilla.firefox[9264]: NOTE: child process received `Goodbye', closing down
Mar 31 11:36:14 NAME ntpd[20]: time reset -4.060579 s
Mar 31 12:11:05 NAME firefox[9264]: -deltaZ is deprecated for NSEventTypeMagnify. Please use -magnification.
Mar 31 15:19:22 NAME kernel[0]:
Mar 31 15:28:23 NAME kernel[0]:
Mar 31 15:28:53: --- last message repeated 7 times ---
Mar 31 15:28:23 NAME kernel[0]:
Mar 31 15:30:22 NAME kernel[0]:
Mar 31 15:56:08 NAME kernel[0]:
Mar 31 15:56:13: --- last message repeated 1 time ---
Mar 31 15:56:13 NAME loginwindow[31]: in pam_sm_authenticate(): Failed to determine Kerberos principal name.
Mar 31 15:56:16 NAME kernel[0]:
Mar 31 15:56:46: --- last message repeated 8 times ---
Mar 31 16:00:10 NAME kernel[0]:
Mar 31 16:00:40: --- last message repeated 3 times ---
Mar 31 16:00:44 NAME kernel[0]:
Mar 31 16:01:14: --- last message repeated 5 times ---
Mar 31 16:02:36 NAME kernel[0]:
Mar 31 16:03:06: --- last message repeated 9 times ---
Mar 31 16:03:22 NAME kernel[0]:
Mar 31 16:10:31 localhost com.apple.launchd[1]: *** launchd[1] has started up. ***
Mar 31 16:17:50 localhost DirectoryService[15]: Improper shutdown detected
Mar 31 16:17:54 localhost fseventsd[33]: event logs in /.fseventsd out of sync with volume. destroying old logs. (707133 444 707763)
Mar 31 16:17:54 localhost bootlog[41]: BOOT_TIME: 1364713830 0
Mar 31 16:17:58 localhost fseventsd[33]: log dir: /.fseventsd getting new uuid: NUMBER
Mar 31 16:17:58 localhost blued[42]: Apple Bluetooth daemon started
Mar 31 16:18:02 localhost mDNSResponder[28]: mDNSResponder mDNSResponder-258.21 (May 26 2011 14:40:13) starting
Mar 31 16:18:03 localhost com.apple.usbmuxd[21]: usbmuxd-296.4 on Dec 21 2012 at 16:11:14, running 64 bit
Mar 31 16:18:04 localhost configd[13]: bootp_session_transmit: bpf_write(en1) failed: Network is down (50)
Mar 31 16:18:04 localhost configd[13]: DHCP en1: INIT transmit failed
Mar 31 16:18:04 localhost configd[13]: network configuration changed.
Mar 31 16:18:04 NAME configd[13]: setting hostname to "NAME.local"
Mar 31 16:18:04 NAME /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[29]: Login Window Application Started
Mar 31 16:18:04 NAME configd[13]: network configuration changed.
Mar 31 16:18:04 NAME mDNSResponder[28]: mDNSPlatformSetDNSConfig: Error: dns_configuration_copy returned NULL
Mar 31 16:18:04 NAME configd[13]: network configuration changed.
Mar 31 16:18:11 NAME mds[27]: (Normal) DiskStore: Creating index for /
Mar 31 16:18:17 NAME loginwindow[29]: Login Window Started Security Agent
Mar 31 16:18:18 NAME WindowServer[71]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:18:18 NAME com.apple.WindowServer[71]: Sun Mar 31 16:18:18 NAME.local WindowServer[71] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:18:29 NAME SecurityAgent[92]: NSSecureTextFieldCell detected a field editor ((null)) that is not a NSTextView subclass designed to work with the cell. Ignoring...
Mar 31 16:18:30 NAME loginwindow[29]: Login Window - Returned from Security Agent
Mar 31 16:18:30 NAME loginwindow[29]: USER_PROCESS: 29 console
Mar 31 16:18:30 NAME com.apple.launchd.peruser.501[96] (com.divx.agent.postinstall): Unknown key: LimitToSessionType
Mar 31 16:18:30 NAME com.apple.launchd.peruser.501[96] (com.apple.ReportCrash): Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
Mar 31 16:18:36 NAME root[113]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds
Mar 31 16:18:37 NAME root[130]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000
Mar 31 16:18:37 NAME root[130]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.apple.com
Mar 31 16:18:37 NAME root[130]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known
Mar 31 16:18:38 NAME-2 com.apple.launchd.peruser.501[96] (com.apple.mrt.uiagent[123]): Exited with exit code: 255
Mar 31 16:18:38 NAME-2 com.apple.launchd.peruser.501[96] (com.apple.Kerberos.renew.plist[124]): Exited with exit code: 1
Mar 31 16:19:55 NAME-2 XProtectUpdater[19]: NSURLConnection error: Error Domain=NSURLErrorDomain Code=-1009 UserInfo=0x100174890 "This computer’s Internet connection appears to be offline." Underlying Error=(Error Domain=kCFErrorDomainCFNetwork Code=-1009 UserInfo=0x1001744e0 "This computer’s Internet connection appears to be offline.")
Mar 31 16:19:55 NAME com.apple.launchd[1] (com.apple.xprotectupdater[19]): Exited with exit code: 255
Mar 31 16:22:04 NAME kextd[10]: updated kernel boot caches
Mar 31 16:25:04 NAME Software Update[178]: SWU: scan found 0 products:
Mar 31 16:25:05 NAME Software Update[178]: Error Domain=NSURLErrorDomain Code=-1009 UserInfo=0x10052e600 "This computer’s Internet connection appears to be offline." Underlying Error=(Error Domain=kCFErrorDomainCFNetwork Code=-1009 UserInfo=0x10052f760 "This computer’s Internet connection appears to be offline.")
Mar 31 16:25:14 NAME com.apple.launchd[1] (com.apple.suhelperd[181]): Exited with exit code: 2
Mar 31 16:25:18 NAME configd[13]: network configuration changed.
Mar 31 16:26:17 NAME Software Update[188]: SWU: scan found 1 products:\n041-9605
Mar 31 16:26:30 NAME ntpd[18]: time reset +1.140167 s
Mar 31 16:26:57 NAME com.apple.launchd[1] (com.apple.suhelperd[190]): Exited with exit code: 2
Mar 31 16:26:57 NAME com.apple.launchd.peruser.501[96] ([0x0-0xf00f].com.apple.Console[142]): Exited: Killed
Mar 31 16:26:57 NAME com.apple.launchd.peruser.501[96] ([0x0-0x15015].com.apple.SoftwareUpdate[188]): Exited: Killed
Mar 31 16:26:57 NAME com.apple.launchd.peruser.501[96] (com.apple.AirPortBaseStationAgent[126]): Exited: Killed
Mar 31 16:26:57 NAME loginwindow[29]: DEAD_PROCESS: 29 console
Mar 31 16:26:57 NAME /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[200]: Login Window Application Started
Mar 31 16:26:58 NAME loginwindow[200]: USER_PROCESS: 200 console
Mar 31 16:26:58 NAME WindowServer[203]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:26:58 NAME com.apple.WindowServer[203]: Sun Mar 31 16:26:58 NAME.local WindowServer[203] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:26:59 NAME Software Update[209]: Looking for products to install
Mar 31 16:27:02 NAME Software Update[209]: Performing preflight
Mar 31 16:27:02 NAME Software Update[209]: Preparing session
Mar 31 16:27:02 NAME Software Update[209]: Starting session
Mar 31 16:27:03 NAME Software Update[209]: PKG: extracting "com.apple.pkg.MacBookProSMCUpdate"
Mar 31 16:27:03 NAME Software Update[209]: PKG: pre-flight scripts for "com.apple.pkg.MacBookProSMCUpdate"
Mar 31 16:27:03 NAME Software Update[209]: PKG: pre-install scripts for "com.apple.pkg.MacBookProSMCUpdate"
Mar 31 16:27:16 NAME Software Update[209]: REQ: moving files into place with shove
Mar 31 16:27:17 NAME Software Update[209]: PKG: post-install scripts for "com.apple.pkg.MacBookProSMCUpdate"
Mar 31 16:27:17 NAME Software Update[209]: PKG: post-flight scripts for "com.apple.pkg.MacBookProSMCUpdate"
Mar 31 16:27:17 NAME Software Update[209]: PKG: writing receipt for "com.apple.pkg.MacBookProSMCUpdate"
Mar 31 16:27:17 NAME Software Update[209]: REQ: install succeeded
Mar 31 16:27:18 NAME Software Update[209]: SWU: installing "MacBook Pro SMC Firmware Update, 1.6"
Mar 31 16:27:20 NAME [0x0-0x1a01a].com.apple.SoftwareUpdate[209]: /: no supported helper partitions to update.
Mar 31 16:27:20 NAME kextd[10]: updated kernel boot caches
Mar 31 16:27:20 NAME Software Update[209]: kextcache returned 0
Mar 31 16:27:20 NAME Software Update[209]: Running /sbin/reboot
Mar 31 16:27:20 NAME reboot[242]: rebooted by Caithris
Mar 31 16:27:20 NAME reboot[242]: BOOT_TIME: 1364714840 524942
Mar 31 16:27:20 NAME mDNSResponder[28]: mDNSResponder mDNSResponder-258.21 (May 26 2011 14:40:13) stopping
Mar 31 16:27:20 NAME DirectoryService[15]: BUG in libdispatch: 10K549 - 1960 - 0x10004004
Mar 31 16:27:20 NAME WindowServer[203]: hidd died. Reestablishing connection.
Mar 31 16:27:20 NAME WindowServer[203]: Unable to create event queue via hidd: (0x10000003)
Mar 31 16:28:03 localhost com.apple.launchd[1]: *** launchd[1] has started up. ***
Mar 31 16:29:52 localhost bootlog[47]: BOOT_TIME: 1364714882 0
Mar 31 16:29:53 localhost mDNSResponder[34]: mDNSResponder mDNSResponder-258.21 (May 26 2011 14:40:13) starting
Mar 31 16:29:54 localhost configd[13]: network configuration changed.
Mar 31 16:29:54 NAME configd[13]: setting hostname to "NAME.local"
Mar 31 16:29:54 NAME com.apple.usbmuxd[27]: usbmuxd-296.4 on Dec 21 2012 at 16:11:14, running 64 bit
Mar 31 16:29:56 NAME blued[17]: Apple Bluetooth daemon started
Mar 31 16:29:57 NAME /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[35]: Login Window Application Started
Mar 31 16:29:59 NAME configd[13]: network configuration changed.
Mar 31 16:30:12: --- last message repeated 2 times ---
Mar 31 16:30:12 NAME ntpd[24]: time reset +0.227711 s
Mar 31 16:30:13 NAME loginwindow[35]: Login Window Started Security Agent
Mar 31 16:30:14 NAME WindowServer[61]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:30:14 NAME com.apple.WindowServer[61]: Sun Mar 31 16:30:14 NAME.local WindowServer[61] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:30:21 NAME SecurityAgent[96]: NSSecureTextFieldCell detected a field editor ((null)) that is not a NSTextView subclass designed to work with the cell. Ignoring...
Mar 31 16:30:22 NAME loginwindow[35]: Login Window - Returned from Security Agent
Mar 31 16:30:22 NAME loginwindow[35]: USER_PROCESS: 35 console
Mar 31 16:30:22 NAME com.apple.launchd.peruser.501[99] (com.divx.agent.postinstall): Unknown key: LimitToSessionType
Mar 31 16:30:22 NAME com.apple.launchd.peruser.501[99] (com.apple.ReportCrash): Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
Mar 31 16:30:32 NAME com.apple.launchd.peruser.501[99] (com.apple.mrt.uiagent[124]): Exited with exit code: 255
Mar 31 16:30:35 NAME com.apple.launchd.peruser.501[99] (com.apple.Kerberos.renew.plist[125]): Exited with exit code: 1
Mar 31 16:30:47 NAME mdworker[81]: (Error) SyncInfo: Catalog changed during searchfs too many times -- falling back to fsw search /
Mar 31 16:36:05 NAME mdworker32[158]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:36:22 NAME mdworker32[161]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:36:29 NAME [0x0-0x10010].org.mozilla.firefox[149]: NOTE: child process received `Goodbye', closing down
Mar 31 16:39:07 NAME mdworker[157]: Warning: unknown JFIF revision number 0.01
Mar 31 16:39:22 NAME login[182]: USER_PROCESS: 182 ttys000
Mar 31 16:40:34 NAME /System/Library/CoreServices/CCacheServer.app/Contents/MacOS/CCacheServer[132]: No valid tickets, timing out
Mar 31 16:40:35 NAME mdworker[157]: Error, could not create MachMessagePort for com.apple.AddressBook.abd
Mar 31 16:40:37 NAME mdworker[157]: Unable to parse date (<XHTML-STRIPONREPLY>
</XHTML-STRIPONREPLY>)
Mar 31 16:40:38 NAME mdworker[157]: Unable to parse date ( S<XHTML-STRIPONREPLY>
</XHTML-STRIPONREPLY>him to any)
Mar 31 16:40:41: --- last message repeated 1 time ---
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 1
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 2
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 3
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 4
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 5
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 6
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 7
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 8
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 9
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 10
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 11
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 12
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 13
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 14
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 15
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 16
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 17
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 18
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 19
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 20
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 21
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 22
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 23
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 24
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 25
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:40:41 NAME mdworker[157]: Invalid char ^M for PropertyName in line 26
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:40:41 NAME mdworker[157]: Invalid char ^M for PropertyName in line 26
Mar 31 16:40:41 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 1
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 2
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 3
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 4
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 5
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 6
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 7
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 8
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 9
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 10
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 11
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 12
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 13
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 14
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 15
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 16
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 17
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 18
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 19
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 20
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 21
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 22
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 23
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 24
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 25
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char ^M for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char ^M for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char ^M for PropertyName in line 26
Mar 31 16:40:43 NAME mdworker[157]: Invalid char \n for PropertyName in line 26
Mar 31 16:41:27 NAME mdworker[157]: Corrupt JPEG data: 1 extraneous bytes before marker 0xd9
Mar 31 16:41:27 NAME mdworker[157]: JPEG datastream contains no image
Mar 31 16:41:33: --- last message repeated 1 time ---
Mar 31 16:41:33 NAME login[182]: DEAD_PROCESS: 182 ttys000
Mar 31 16:41:50 NAME mdworker[156]: iCal.mdimporter: could not parse ICS file: /Applications/Microsoft Office 2011/Office/OutlookCore.framework/Versions/14/Resources/en.lproj/Timezones.ics
Mar 31 16:41:51 NAME mdworker32[204]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Mar 31 16:43:41 NAME [0x0-0x10010].org.mozilla.firefox[149]: NOTE: child process received `Goodbye', closing down
Mar 31 17:07:10 NAME firefox[149]: -deltaZ is deprecated for NSEventTypeMagnify. Please use -magnification.
Thanks again- I mean it. It's lousy being stuck away from home when crazy thing happen to your main line of communication!
-Caithris

The gray screen with loading bar issue is a at boot fsck (file system check) that has discovered something wrong with your boot drive/partition and was attempting to fix it.
OS X is booting but can't complete, so that means your hard drive is good, just likely has been either subjected to shock which damaged data on the platters, or bad sectors (the drive is dying if after fixing it, problems occurs again), or something messed something up in the file structure.
Firefox is currently at 19.02, so it appears your background auto-update has not been occurring, which makes me suspect the machine's data is broken in some manner or you have malware on the machine blocking the updates.
Your problems are multiple, in your case I advise a complete erase and install.
1: If you have a backup of your user data on a external storage drive (not TimeMachine as it might be corrupted and compromised with malware it's just going to restore back) then your good, else you have to do this.
Create a data recovery/undelete external boot drive
Copy your data to a blank plain jane external storage drive as you want no executable files on it when you connect to the cleaned machine later.
2: Once your data is safely copied (copy visible files manually and what you know is good, not folders that can contain invisible malware programs!) then disconnect the drive(s)
3: Next assume all writeable media is contaminated with malware and treat as so. Even if you erased it.
4: Stick in your 10.6 install disk and reboot holding the c or option key down. You want Disk Utility and you want to select the ENTIRE internal drive and MUST USE the Security Option > Zero All Data (unless your in the military then use 7x erase, do not use 35x as it will take weeks and is unnecessary)
The Zero/7x erase will do two things, do a low level format and erradicate everything (including hidden stuff and deleted files) also will map off any failing sectors on the hard drive.
5: Follow the procedure here to install 10.6
How to erase and install Snow Leopard 10.6
6: Reboot the machine twice, then once you set up the machine (using a alias of course and not allowing registration), use a secured network and IMMEDIATLY Software update to 10.6.8, if you can download the 10.6.8 Combo update on another secure machine to a (new) USB thumb drive and install it on the clean Mac, do that instead.
WiFi security issues, at home and WiFi hotspots
https://support.apple.com/kb/DL1399
Still run Software update afterwards as Apple might not have fully updated the combo update yet.
7: Once you machine is secure, download the free ClamXav and run a scan on the external storage drive with just your files, perhaps one or more PDF's or other files are not what they seem to be.
8: Make sure to install fresh copies of software from original sources and not from rewriteable media, update them to be current. Malware can be hidden in copies of programs.
9: Trash all your rewritable media, or use a Linux PC or Linux Mint in a virtual machine (VirtualBox) on another computer like Windows to scrub and reformat all the rewritable media before attaching them to the clean Mac. You have to make sure it's getting the entire media.
10: Once your machine is set back up, then make clones and time and date them.
Most commonly used backup methods
If your still having problems with the machine, it's likley a failing hard drive and you will have to replace it and repeat the steps above pretty much.
Really it's best to replace the drive in the interest of security.
Install/upgrade RAM or storage drive in Mac's
For performance of Snow Leopard, check out this tip
For Snow Leopard Speed Freaks
Your overseas, if your in a foriegn country you have to assume FinSpy is being installed on your machine (uses a older iTunes verison "update" to get on) or there is other tricks via the ISP to install something on your machine. So mix things up and don't stick any old USB you see laying around into your Mac.
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents#/

Running two SSIDs, one with WPA2 and one with WEP

Similar Messages

Maybe you are looking for