Running with Smartband only

Hi everyone,
I know others have posted about this, but I can't find an answer to my specific problem...
I went running today, with my Smartband only, leaving my phone at home. When I got back LifeLog showed my run, down to the closest minute, but then when I went back on an hour or so later the run had disappeared, it's still showing my steps but the running value is down to 0. Does anyone know why this may happen?
Thank you in advance!

I'm still struggling with this, tried resetting it etc and it's still the same. Did a 20 minute jog today, at 12pm I took a screenshot and the running had tracked, by 12.23pm it has disappeared. I'd not disconnected my Smartband or anything. My partner still has the same problem with his smartband and phone. I've noticed that my Smartband will only connect with Bluetooth, when I turn it off and try to connect with NFC only my phone turns Bluetooth on automatically. Could that be affecting it? Thank you all for your help once more.

Similar Messages

Msi Big Bang Xpower II can only run with 3 memory modules?

Hello there! I've just got my new system up and running. But it cant boot with 4 memory modules when there is a module in slot 7? I have a 4x8gb kit from corsair (CMP32GX3M4X1600C10), and a Msi Big Bang Xpower II..
When i start it, it just shows me the debug code "67" which is "Late Cpu Initialization" according to the "User Guide".. It stays there, for about 15 seconds, then it shuts down, and does the same, over and over..
Atm, i'm running with 3 modules, and there's no problems at all! I've testet ALL memory blocks, in another computer, and they run just fine..
What should i do?

Quote from: xmad on 25-September-12, 21:09:52
Also, what cpu, bios version , memory type etc
Make sure the mem mods are in the proper slots for tri channel operation.
>>Posting Guide<<
If everything comes up clean, update to the most recent bios. Only do this if your computer is stable in bios. IE You are only having crashes in windows etc.
>>Use the MSI HQ Forum USB flasher<<
http://www.msi.com/product/mb/Big-Bang-XPower-II.html#/?div=BIOS
**Merged
Core i7 3930K, V1.2 Bios, 32GB Corsair Dominator Quad channel 1600Mhz Kit.. The memory are installed as the manual says..

Time Capsule only runs with 1,1Mbit up/down during data transfer, internet speed is ok, TC is used to extend an existing network

Hello Everyone,
I have a new 2TB Time Capsule running with a MacBook Air. I want to use the TC to access data (Aperture library, iTunes library, other Files) and to backup my MacBook Air via Time Machine. I set it up, integrated the TC in my Network (FritzBox) by choosing "extend existing network" and it works. BUT only with 1.1Mbit/second while writing or reading Data to/from it. Internet speed is very good, like it was before. While the 1.1Mbit/second seem to be ok with Aperture and iTunes (streaming music and movies) it is still painfully slow and I'm not realy happy with that
I've read that:
The 1.1Mbit problem is pretty common when Time Capsule is integrated and used to extend a network (bridge modus), it also looses all ethernet connectivity then (that woul explain why connecting it by ethernet didn't help during initial setup and data transfer)
Is there a solution besides ditching the Fritzbox and using the TC to build the network? Because basicly I still need the Fritzbox for its DECT features.
Thank you for any help in advance and have a nice day,
Olli

You have double hop wireless with this setup..
You should bridge the TC.. that is router bridge not wireless bridge, and plug the TC into the Frizyboy by ethernet.
Then you can setup the TC wireless to reinforce the fritzy..
Same wireless name as SSID.
Same security settings... really should be WPA2 AES or in TC personal.
Same password..
Just different wireless channel.
Then you can use 5ghz on the TC if you are up close and personal.

I have a production mobile Flex app that uses RemoteObject calls for all data access, and it's working well, except for a new remote call I just added that only fails when running with a release build. The same call works fine when running on the device

I have a production mobile Flex app that uses RemoteObject calls for all data access, and it's working well, except for a new remote call I just added that only fails when running with a release build. The same call works fine when running on the device (iPhone) using debug build. When running with a release build, the result handler is never called (nor is the fault handler called). Viewing the BlazeDS logs in debug mode, the call is received and send back with data. I've narrowed it down to what seems to be a data size issue.
I have targeted one specific data call that returns in the String value a string length of 44kb, which fails in the release build (result or fault handler never called), but the result handler is called as expected in debug build. When I do not populate the String value (in server side Java code) on the object (just set it empty string), the result handler is then called, and the object is returned (release build).
The custom object being returned in the call is a very a simple object, with getters/setters for simple types boolean, int, String, and one org.23c.dom.Document type. This same object type is used on other other RemoteObject calls (different data) and works fine (release and debug builds). I originally was returning as a Document, but, just to make sure this wasn't the problem, changed the value to be returned to a String, just to rule out XML/Dom issues in serialization.
I don't understand 1) why the release build vs. debug build behavior is different for a RemoteObject call, 2) why the calls work in debug build when sending over a somewhat large (but, not unreasonable) amount of data in a String object, but not in release build.
I have't tried to find out exactly where the failure point in size is, but, not sure that's even relevant, since 44kb isn't an unreasonable size to expect.
By turning on the Debug mode in BlazeDS, I can see the object and it's attributes being serialized and everything looks good there. The calls are received and processed appropriately in BlazeDS for both debug and release build testing.
Anyone have an idea on other things to try to debug/resolve this?
Platform testing is BlazeDS 4, Flashbuilder 4.7, Websphere 8 server, iPhone (iOS 7.1.2). Tried using multiple Flex SDK's 4.12 to the latest 4.13, with no change in behavior.
Thanks!

After a week's worth of debugging, I found the issue.
The Java type returned from the call was defined as ArrayList. Changing it to List resolved the problem.
I'm not sure why ArrayList isn't a valid return type, I've been looking at the Adobe docs, and still can't see why this isn't valid. And, why it works in Debug mode and not in Release build is even stranger. Maybe someone can shed some light on the logic here to me.

HT4824 My iPhone is running with ios 4.2.1 & current version of ios is 6.0.1 in this case how can i update my iPhone to ios 4.3.5? itune will show only latest version of ios.

My iPhone is running with ios 4.2.1 & current version of ios is 6.0.1 in this case how can i update my iPhone to ios 4.3.5? itune will show only latest version of ios.

If you have iPhone 3G, the latest and greatest is IOS 4.2.1.
If you have iPhone 3GS or later, you can only update to IOS 6.0.1.
For iPhone 5 and iPad mini, you can update to IOS 6.0.2.

Formula for report to run with data of only current day

I need a report that whenever refreshed it run with data for only the current day. It is for knowing how many checks were performed from the start of the current day to the time the report runs. Iu2019ve tried to use the select expert but I guess I need to use a formula in it.
Thanks,
Andreia

Andreia,
I think you've posted this into the wrong forum!
-Anil

T41 won't run on AC only or with fully charged battery

I just got a used T41 laptop and have a weird problem. It runs fine on battery only or with a partially charged battery. But when I remove the battery and try to run on AC only, I get the "charger removed beep and screen flash warning" over and over again. The same thing happens when the battery is installed and reaches full charge. As it approaches full charge, I'll get the warning once in awhile. But once it reaches full charge, or with the battery removed, it happens intermittently, every few seconds.
If I turn off the "Power Control" alarm in the BIOS, I don't get the beeps but the screen still flashes. Also, the alarms start before the OS is loaded. They occur even at the first screen where it allows you to press the IBM Access button. It seems to be some sort of "over voltage" alarm. I have Grub installed for dual booting XP and Linux and while Grub menu is displayed and I turn the LCD brightness up and down, the alarm frequency increases as I decrease the brightness.
As it stands, I can only use the computer by unplugging the AC when the battery reaches about 90% charge, running on battery only till it drops to about 20%, and then plugging the AC back in. Frustrating!!!

Thank you for the information that does me no good at all. I only paid $75 for the laptop and it will allow me to sell a good working Acer laptop for much more money. I can put up with the inconvenience with my personal laptop. In fact, it works quite well with just a 12v battery connected to the AC connector. With only 12v applied, instead of 16v, the over voltage sensor doesn't kick in. There are always several approaches to any problem and I was hoping someone here in the forum had one more elegant than mine. If not, I can live with mine. No way is replacing the MB a solution.
Thanks anyway
Lew

Hi i received the nano 7th gen for Christmas and I only seem to get 5 hours of battery life. I use the Bluetooth and Nike app so I expect more drain on the battery. But I got more time out of running with my iPhone. Does this sound normal? I thought I sh

Hi i received the nano 7th gen for Christmas and I only seem to get 5 hours of battery life. I use the Bluetooth and Nike app so I expect more drain on the battery. But I got more time out of running with my iPhone. Does this sound normal? I thought I should get close to 30 hrs of just play time alone.
ALso, my wife got me the Belkin armband to run with the nano but I sweat through the band resulting in the back of the iPod to get wet. Surely this is not good. Anyone have a recommendation for an armband that keeps moisture away from the pod?

iPod Nano are small and they don't use Wi-Fi access so you get less power time on a Nano. As for iPhone, since you got apps, Wi-Fi + 3G access, and everything else, they give you more time so you can keep using. Nanos are ment to listen to music, listen to radio, view your photos, watch videos (without Wi-Fi) and since you got BlueTooth on the nano, it counts as wireless access so it drains your battery faster.

My external 27" AOC display only runs with 1080p

My external 27" AOC display only runs with 1080p, even though my 27" iMac is capable of 2560x1440 via the attached mini-DisplayPort to DisplayPort cable. How can I get 2560x1440?
When I run recovery mode, then I get the full 2560x1440 pixels. But when I boot back to 10.9.2, then I can only choose a maximum of 1080p.

After some hours I found a solution...
But let me vent a little bit first: My MacBook Air, which I have not yet upgraded to Mavericks, is able to drive the AOC display through DisplayPort at full resolution without a problem.
Even an older lenovo Notebook with Windows 7 immediatelly used the intended resolution when hooking up the 27" screen. Windows 7 outplaying Mavericks. Oh boy...
So it seems, that Mavericks introduced some "improvement" that limitd "unknown" displays to 1080p...
By the way: Clearing PRAM didn't resolve my issue. Neither did holding down the Option key when klicking in the "Scaled" button in the screen resolution area of the system preferences for my screen.
Anyway: I found out that I can use the plist file for a DELL 27" screen, which google found for me, copy this to /System/Library/Displays/Overrides and then rename the folder and file to match the ID I got back from ioreg.
Obviously one has to be careful when mixing hardware data in this way. But since a modern screen will simply refuse to be driven with a signal that is out of spec, and since there are not too many different 27" pannels with 2560x1440 out there these days, this felt like a pretty safe thing to do... Your mileage may vary though!
Unfortunately I don't have a plist editor installed. Thus I can only look at the XML contained in the plist file. With the plist editor from Mac (-> dev tools) it should be possible to edit available resolutions directly (in hex).

I have a on line office manager that will only run with windows 7 or vista, how can I run it on my iMac?

I have an online office manager that will only run with windwos 7 or Vista, how can I run it on iMac?

If they don't have a Mac version and you must have it, you'll have to install Windows in Boot Camp or similar app.

Run plan with SCO only

Hi,
How do we run an ASCP plan with SCO only (No MBP, No HLS)?
I think a profile option has to be created for that.
I want to know the details for this profile option so that I can create and test the plan.
Is there anything else which needs to be done for SCO-only plan?
Regards

Siri requires internet access, which can be with an available wi-fi network.

How do I create an automator task to run TimeMachine at only certain hours?

Hi
In another forum it was suggested I make an Automator task for setting TimeMachine to only run at certain hours of the day.
I've not used Automator in the past.
I'd like to set it to run TimeMachine from only 1AM to 7 AM.
Can anyone point me to a good source to figure out how to do this? Or just share with me how to write the task?
Thanks

You might look at this program.
TimeMachineEditor - Time Software - Free

K8n neo2 running with 260 FSB ?

Hi !
Well, I have one question about the FSB and Multi settings.
first, my sys:
-K8N Neo2 Platinum
-AMD64 3500+ winchester
-OCZ 2x512 DDR (PC 3500 - 433Mhz) Ram
-2x S-ATA HDD Hitachi 160GB @ Sata 3&4
-550W PS
So, with some tests, I can found the fastest CPU-freq @ 2600Mhz with 1,58V VCore - testing with Prime95.
But I want the fastest clock for the rams, too. The Ram works with FSB 217, DDR200-setting in BIOS. Multi 11x. very well at 217Mhz...
first settings:
FSB @ 237 / Multi @ 11x / HT @ 4x / Ram set to DDR166.
So the effective CPU-clock is 2604Mhz, the ram is at 186 Mhz.
The setting works fine... but with very poor ram-clock...
(I had to set the ram to DDR166, because with DDR200-Setting the clock will be 237 which is too high and I can´t boot. )
2nd setting:
FSB @ 248 / Multi @10.5 / HT @4x / Ram set to DDR166.
The setting works fine... The Mobo shows a ram-clock of 208Mhz. The Tool "Clock-Gen" shows a ram-clock of 200Mhz...(I dont´know which is right...?) But: The Ram-Clock can ba 217Mhz, I guess..?
3rd setting:
FSB @ 260 / Multi @10 / HT @3x / Ram set to DDR166.
This setting crashes up while booting.... normally, I think, the CPU-clock will be 2600 (which will work), the RAM will divided down to 217 Mhz.
Now my prob: the CPU runs with 2604 Mhz, the RAM runs with 217Mhz - but why can´t I set the FSB to 260 and Multi 10x ?? PS: the system ist still crashing, when I set the Multi to 10x and try FSB to 250Mhz... ?
Does anyone know ??
Many thanks !
A.

Just so you know, when you use dividers, your memory performance is only as good as the lowest setting. For example, I you have a system with ddr333 memory and a CPU with a 333mhz FSB your memory performance is as follows:
Memory Peformance:
133CPU x 133mem = 166CPU x 133mem
CPU performance:
133CPU x 133mem
As opposed to:
Memory Peformance:
133CPU x 166mem CPU performance:
133CPU x 166mem
The Kicker:
Memory Performance (first versus second):
133CPU x 133mem 166CPU x 133mem CPU Performance (first versus second):
133CPU x 133mem 166CPU x 133mem
I neglected to try overall combined performance like 3dmark01/03/05 but I was on a time budget at the time and only concerned with running a 4:5 divider as opposed to a 4:4 divider which my results gave me no increase (but no decrease either).
Therefore, you get no increase in memory performance when using dividers. I used sandra to verify this. I simply used my CPU and RAM in every different configuration I could think of and then ran it and recorded the results. Hopefully I remembered my results correctly.
Yes, you will see a CPU increase with dividers but you will not see a memory increase.
The Kicker Reiterated:
CPU Performance:
(133 CPU x 133 mem
Personally I think you should be happy with an FSB of 248 because that means your memory frequency is 198.4mhz which means you nearly have ddr400. How much of an increase do you think you'll see with 260FSB (208mhz memory frequency (increase of 9.6 mhz))? Personally I think you should be happy with 248 with a 5:4 divider.
ORRRRRRRR:
try benchmarking with a 216FSB x 11mult x 4htt with DDR200 versus 248 x 10mult x 4 htt with DDR166 and see which is faster. You'll do better on the first with memory and better on CPU with the second but the inverse will be the inverse. Then I would do an overall benchmark like 3dmark03/05 and see which had the best overall effect (I'm guessing it will be a somewhat close call but I never tried that... hmmm... something to try now).

How to know that a form is running in query-only mode

I have a form that can run in query-only mode or non-query-only mode depending on the current user who logs in, and I want to change its apprearance dynamically when it's in different modes (for example, enable or disable buttons). Is there a built-in or system variable from which I know that the form is running in query-only mode or not?
Thanks,
Shu

The global variable solution is what we are using now. I thought there are some unpublished built-in or system variables. In my application, there is a public "menu" form from where hundreds of forms are CALLed with some in query-only mode and some in non-query-only mode depending on the current user role. :PARAMETER.QUERY_ONLY will always be 'NO' because the "menu" form is started in non-query-only mode. But it's good to know about it.
Thank you very much for your replies,
Shu

Won't run with 2 CPUs

I just replaced my 6501 motherboard with one that MSI sent me. When I install both processors the computer most times hangs at startup screen. Lights 2 and 3 are red which indicates it stops at the Bios sign-on.
It hangs where it says AMD MP 2800 Processor but before memory test and it does not display the , (2 cpu's) to the far right of the processor (80% of the time this happens on boot-up). Occasionally when I reboot it will detect both CPUs and will initialize the bios and then start loading windows at which point it immediately reboots.
If I remove the second CPU and reboot the machine boots fine and I can load up windows.
I have swapped both CPUs and put both of them in the Primary CPU slot and they both boot up and run fine no issues. Only when I try to have both in do I have problems. The reason I replaced the MB was because of some dried out capacitors. I got the 1.91 bios update already. Not sure what might be causing this but I want both CPUs working like before. Any help would be appreciated.
This is the first time this board has been used. I pulled it out of the box this morning. It is a refurbished board from MSI. The other board with the dried out capacitors ran both CPUs fine without issue but I had data transfer issues so had to replace it. The newest bios available for this motherboard appears to be award bios v1.91 which is the one I have.
If any further info is needed let me know what else you need. (I am on the computer having troubles right now but with only 1 CPU running - works fine albeit a bit slower)

Okay. Power supply info. Had to break my system down because the side that had the info on it was covered by the top of the tower.
Enhance Electronics
Model: ATX-1140F with Outlet
400 Watt Power Supply
+3.3v(28A), +5V(38A), +12V(18A), -12V(.8A), -5V(.5A), +5VSB(2A)
The 4 pin connector is plugged in. =) I did not overlook that.
As for trying it with fewer memory sticks, no I have not tried that but keep in mind that earlier today the previous mobo was in this machine and running with both CPUs and all 3 memory sticks (512, 512, 1024). All in the same memory slots as the original mobo. I pulled each one and inserted it in the new mobo before taking out the next one to be sure I put them back in the same slot.
I checked and double checked all the bios settings and they match. The only thing that has changed since this morning is the replacement mobo and that is the exact same model as the one I replaced. System works fine with 1 CPU but not with 2. What might cause that on this motherboard but not the original one?

Running with Smartband only

Similar Messages

Maybe you are looking for