Runtime error Screen "SAPLXQQM" 0100 could not be generated.

Hi All,
I have one issue with IW21 transaction code( Create PM Notification: Initial). When I'm trying to crteat a Notification of type L1( GEBS LEV PM request ), its going to dump showing the runtime error as,
"At the screen generation it was detected that a screen to be generated has a syntax error or could not be generated due to another error."
Error analysis
    Screen "SAPLXQQM" 0100 could not be generated.
Trigger Location of Runtime Error
    Program                               SAPLXQQM
    Include                                 LIQS0O90
    Row                                     20
I'm using ECC 6.0 version.
When we do syntax check of the progran or screen it is showing syntax error " Field VIQMEL-ZZMTART is not in the data Dictionary'.
Please help me in this.
Thanks & Regards,
Sabu.

Hi Sabu,
The problem is caused by your customizing include, most probably the one in table QMEL.
Field ZZMTART has been created before in one of these CI structures, but some how was deleted it at later stage.
.INCLUDE     CI_QMEL
.INCLUDE     /SAPSMOSS/ATTRIBUTES
.INCLUDE     CLAIM_MANAGEMENT
One way to solve the issue, is by recreating this field again in the customizing include. Or you take it out from the screen enhancement of transaction IW21. You can check the screen enhancement in CMOD. Customizing include changes and screen enhancement changes better to be done after office hour, as the activation normally takes quite some time, and will cause short dump if users are running transaction which tables has the customizing include.
Regards,
Lim...

Similar Messages

Screen "SAPMJ1IFN" 1110 could not be generated.

Hi,
I'm creating sub contracting challen tcode J1IF01.
Here i'm getting runtime error is Screen "SAPMJ1IFN" 1110 could not be generated.
Please guide me where i'm mistake in Sub Contracting.
Regards,
Balakrishna G

Hi Sabu,
The problem is caused by your customizing include, most probably the one in table QMEL.
Field ZZMTART has been created before in one of these CI structures, but some how was deleted it at later stage.
.INCLUDE     CI_QMEL
.INCLUDE     /SAPSMOSS/ATTRIBUTES
.INCLUDE     CLAIM_MANAGEMENT
One way to solve the issue, is by recreating this field again in the customizing include. Or you take it out from the screen enhancement of transaction IW21. You can check the screen enhancement in CMOD. Customizing include changes and screen enhancement changes better to be done after office hour, as the activation normally takes quite some time, and will cause short dump if users are running transaction which tables has the customizing include.
Regards,
Lim...

"Some updateing commands could not be generated ....." error

Hi all,
I am accessing an Oracle server on which I have READ ONLY rights. I am trying to create a DataSet. When I do so, I get an error:
Some updating commands could not be generated automatically. The database returned the following error:
This object has been deleted.
1) Is this just because my access is readonly?
2) A different message might be preferred ("code to submit updates was not created due to limited user rights" or some such.
3) Can I use this even with the error or will I have other problems because the process did not complete correctly?
Thanks,
JustMe

Can't remember how I solved this, but it is solved.

Report RV13ANAH could not be generated

Hello Experts,
I have one issue. In VK13, I give the condtion type and click the Condition information button. I get the error as Report RV13ANAH could not be generated. The program RV13ANAH has syntax error which I found out. The error is table A902 doent have a field KFRST and KBSTAT. But the program has these two fields in the SELECT statement
SELECT * FROM A902 into table t_A902
    WHERE KAPPL = KAPPL
      AND KSCHL = KSCHL
      AND AUART_SD IN F001
      AND VKORG IN F002
      AND KUNNR IN F006
      AND KFRST IN F007
      AND KBSTAT IN F008.
I need to remove these two fields from the program. But i believe this can be done only by generating the table or access or access sequence or doing some settings in the customizing. I do not know what exactly to be done. Could anyone please let me know what needs to be done.
Cheers,
Balaji

Hello Venkatesh,
In KE4A, I dont get 902 table at all. any other clue.
Cheers,
Balaji

BPM Error:Runtime handle of object type could not be created:CX_MERGE_SPLIT

HI Guys...
I am working on a RFC to HTTP scenario:
It is a standard SAP interface ....so we created only ID objects..obviously the BPM delivered by must be correct.
in sxmb_moni_bpe it is throwing th following error texts:
Runtime handle of object type could not be created
Error executing service for node
Exception CX_MERGE_SPLIT occured
component mapping has returned an error
unmodeled exception when executing service for node
No payload found
object FLOWITEM method EXECUTE cannot be executed
I tested the mapping payload from sxmb_moni in IR and it is working fine.
Receiver is an HTTP so could not able to find exactly whats happening as no thrid party tools can be installed....struck up here.
Any iputs will be of help in this area.
Thanx in adavance.
Kiran

any inputs around this plz??

HT201210 I tried to restore my iPhone 4s through iTunes and received error message that Restore could not be completed due to error 2003. Phone now not recognized in iTunes, with prompt to restore, phone w/screen with iTunes symbol and can't use.

I tried to restore my iPhone 4s through iTunes and received error message that Restore could not be completed due to error 2003. Phone now not recognized in iTunes, with repeated prompts to restore phone. Now phone w/screen with iTunes symbol and USB cord can't use. It appears the phone has been restored, but I cannot activate it.
I disabled my anti-software, iTunes and computer software (microsoft vista) are both up to date, I restarted the computer several times. My usb ports are working properly. I followed the troubleshooting suggestions from apple.

yes did you buy it of somebody or a well known company such as apple or carphone warehouse?
and i mean the phone would have been activated in the first place with the sim card you get given when you first get the phone.
trying to activate the phone with another sim card that you did not get when you brought the phone may result in you not being able to activate it
no worries

When I try to save a form as "Reader Extended PDF" in Acrobat Pro, I get an error message "This document could not be reader enabled".

Hello,
When I try to save a form as “Reader Extended PDF” in Acrobat Pro, I get an error message “This document could not be reader enabled”.
The steps I’m following are described below:
1. Insert electronic signatures
- In Tasks, click on “Add New Field -> Digital Signature”.
- Move the square to the place where you want to put the signature and click.
- Fill in the “field name” with the name of the person who has to sign here.
- When it is done, click anywhere on the screen.
- In Tasks, click on “Close Form editing”.
- Go to menu “File -> Save as -> Reader Extended PDF ->Enable additional features”, click on “Save now”.
- Fill in the file name and click on “Save”.
2. Save the Form
- In Tasks, click on “Close Form editing”.
- Go to menu “File -> Save as -> Reader Extended PDF ->Enable additional features”, click on “Save now”.
- Fill in the file name and click on “Save”.
I am using Adobe Acrobat Pro 10.0.0 on a W7 workstation
Here's a screenshot of the problem.
Thanks a lot.
Gael

Read the user manual that came w/the scanner and/or contact HP Support.
http://support.apple.com/kb/PH14141 OS X Mavericks: Reset the printing system
http://support.apple.com/kb/HT3669 Printer and scanner software available for download
A scanner driver you may wish to consider: VueScan Scanner Software

BME-99003: An error occurred, so processing could not continue.

Got the error message below when working with my faces-config.xml file.
I currently have several JSF navigation cases labeled as "!NLS Error" (No Quotes)
Steps to create the error...
1. Create an ADF Faces project with 10-15 pages and navigation rules between each page.
2. Outside of JDeveloper, redo your folder structure on how you store your pages.
3. Inside Jdeveloper, update the source of faces-config.xml to point to the new location of the files.
4. Click on the diagram tab.
On my screen, the diagram for both the old and new files was appearing. When trying to delete the diagram for the old files, I got the error message. I cannot save the file faces-config.oxd_faces.
Message
BME-99003: An error occurred, so processing could not continue.
Cause
The application has tried to de-reference an invalid pointer. This exception should have been dealt with programmatically. The current activity may fail and the system may have been left in an unstable state. The following is a stack trace.
java.lang.NullPointerException
     at oracle.bm.diagrammer.shape.BaseDiagramEdge.startMove(Unknown Source)
     at oracle.bm.diagrammer.track.MoveTracker.<init>(Unknown Source)
     at oracle.bm.diagrammer.track.SelectionTracker.mousePressed(Unknown Source)
     at oracle.bm.diagrammer.track.ModularTracker.processEvent(Unknown Source)
     at oracle.bm.diagrammer.track.SelectionTracker.processEvent(Unknown Source)
     at oracle.bm.diagrammer.track.TrackerStack.processEvent(Unknown Source)
     at oracle.bm.diagrammer.BaseDiagramView$53.processEvent(Unknown Source)
     at oracle.bm.diagrammer.PageView$PageViewPanel.fireEvent(Unknown Source)
     at oracle.bm.diagrammer.PageView$PageViewPanel.processEvent(Unknown Source)
     at java.awt.Component.dispatchEventImpl(Component.java:3955)
     at java.awt.Container.dispatchEventImpl(Container.java:2024)
     at java.awt.Component.dispatchEvent(Component.java:3803)
     at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:4212)
     at java.awt.LightweightDispatcher.processMouseEvent(Container.java:3889)
     at java.awt.LightweightDispatcher.dispatchEvent(Container.java:3822)
     at java.awt.Container.dispatchEventImpl(Container.java:2010)
     at java.awt.Window.dispatchEventImpl(Window.java:1774)
     at java.awt.Component.dispatchEvent(Component.java:3803)
     at java.awt.EventQueue.dispatchEvent(EventQueue.java:463)
     at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:242)
     at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:163)
     at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:157)
     at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:149)
     at java.awt.EventDispatchThread.run(EventDispatchThread.java:110)
Action
If further errors occur, you should restart the application.
Also, report the problem on the JDeveloper forum on otn.oracle.com, or contact Oracle support, giving the information from this message.
________________________________________________________________________________

To fix this issue, I performed the following...
1. Copy the xml from the faces-config source tab.
2. Delete the faces-config.xml file within JDeveloper.
3. Create a new faces-config.xml file.
4. Paste xml from step one into the faces-config source tab.
Really not that bad of an issue, I only posted because the error message directed me to.

Error #2057: The page could not be added to the print job.

I've been making myself crazy over this one. I'm trying to print a complex multi-page "report" in Flex, but I keep getting this error every time I try to call FlexPrintJob.addObject(page):
Error #2057: The page could not be added to the print job.
Here is the basic scenario... I have created a new control I call a PrintVBox that extends the normal VBox control. After adding all of the children properly to the component, I wait for an update event (so that the heights of all the components are calculated) and then I call a custom method I have added to PrintVBox that "paginates" the control.
This pagination method essentially decides how many of the items in the VBox can fix on each page, and splits them up into separate pages. Here's a somewhat graphic example of what happens:
(before paginate)
***** PrintVBox ********
     [ Item 1 ]
     [ Item 2 ]
     [ Item 3 ]
     [ Item 4 ]
     [ Item 5 ]
This single VBox with 5 items, after calling the paginate method becomes something like this:
(after paginate)
****** PrintVBox ********
     **** VBox (page1) ******
               [ Item 1 ]
               [ Item 2 ]
     **** VBox (page 2) ******
               [ Item 3 ]
               [ Item 4 ]
               [ Item 5 ]
So, what was once a single VBox with 5 UIComponents on it is now a VBox that contains two VBoxes, each the exact size of a printable page, one containing the first two items, the other containing the second two items.
In my example that I am working on, my PrintVBox that I have created uses a Repeater to create about 20 HBoxes on the page. I then call
myFlexPrintJob.start()
to show the print dialog and get the user's parameters. I then pass the chosen print height and width to the PrintVBox control and call the paginate method, which creates pages of the desired width/height. I have tested this part thoroughly and displayed the resulting PrintVBox on the screen and it paginates successfully and all is well. After paginate, it has created 3 page VBoxes each holding some of those 20 items.
I then iterate thru PrintVBox.getChildren() array, in this case which is the three VBox pages, and I call:
myFlexPrintJob.addObject(page);
for each one. Each one errors out with the above error. The error is down in the PrintJob code, which is part of the Flash framework and I cannot step through it. I have no indication of why the page can't be added to the print job. Is there a reason this is happening?? Does it have to do with the Repeater that originally created the 20 HBoxes, even though I have now moved those HBoxes down onto separate pages? I'm just so confused here.
I can probably post the entire code chunk if someone really wanted it. I'm currently testing it as an AIR application using a big tester XML data object on the repeater, so that I didn't need a database and such to create the control and test printing. If someone really wants to see what I'm doing, let me know.
HELP! PLEASE!!
Thanks,
Joe

Were you able to solve this problem?
I am currently having the same problem as yours... I created my own printing classes that do all crazy calculation to figure out page breaks and stuff... everything goes well until the point I want to add these pages to the printJob. I get same error?
Any help is highly appreciated.
Thanks,

Error: The specified procedure could not be found

Apparently the password expired on my Windows 7 BETA installation. Upon restart the system notifies me and asks for a new password. After confirming the password I get the error:
"The specified procedure could not be found"
I cannot log in at this point. The old password won't let me in and I can't change it. The administrator account I found is disabled by default.
Is there any way to log in?

Okay, here is your dilemma.
You cannot login to your only account and the local administrator account is in its default disabled mode.
There is a solution, albeit totally unsupported. Go to http://www.sysresccd.org/Main_Page and download the latest SystemRescueCd. Burn a CD from the ISO. When you boot with the SystemRescue CD, you will type ntpass and hit <enter>. From there, make sure you read the screens. You will have make selections depending on how you loaded Windows 7 (clean vs. upgrade vs. dual boot, etc). Using this disk, you CAN enable the local administrator’s account and login in.
I just did the procedure using Windows 7, build 7000 with SystemRescueCd 1.1.6.
Good luck.

My iPod is showing a white screen. I could not see anything. But I can listen to songs by blindly pressing the play button twice. The battery comes only for an hour.? How do I get the display and longer battery?

Hello Friends,
I've two iPod Nanos (4th gen - 8GB). I'm facing a severe problem with both of them. For both iPods, I tried to do this method Simultaneously press the top button + home (central) button. But of no use.
1. My first iPod is showing a white screen. I could not see anything. But I can listen to songs by blindly pressing the play button twice. The battery comes only for an hour.? How do I get the display and longer battery?
2. My second iPod is facing more severe problem. None of the buttons are working. When I connect it my PC it showing "CONNECTED- eject before disconnecting". But it is not ejecting with all the usual methods. When I manually and physically disconnect it from the PC the same "CONNECTED- eject before disconnecting" is still showing till the battery goes off. After that if i press any button it is showing low battery signal. And when i re-connect it to the PC the same process is repeating. When I tied to restore it to the factory settings I'm getting "Error" report.
(I'm using windows 7)
Friends, Please help me with the above problems. It will be a great help.
Thank You.
R.SAMALA

Sounds like some hardware issues, meaning you'll want to take or send the iPods in for service or repairs. You can choose to have Apple do an out of warranty exchange for the prices indicated in the link below or find another third party service perhaps even local to your area.
http://www.apple.com/support/ipod/service/prices/
B-rock

I have a new Ipad air. I have synced it to my PC before. This time I get an error message saying iTunes could not connect to the iPad because the device time out - what do I do?

I have a new Ipad air. I have synced it to my PC before. This time I get an error message saying iTunes could not connect to the iPad because the device time out - what do I do?

Quit iTunes, restart your computer, reset the iPad and try again.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

Screen sequence number could not be determined

Hi, All,
After client copy, I ran MM03, but got an error as below:
screen sequence number could not be determined.
How to solve it?

You need an ABAPER to debug the issue. Also check the logs for more details
Regards
Juan

Error 28: Selected item could not fit into memory question?

hi evreyone,
don't know but Solaris 10 is not making any sense to me at all.the peoblem is i have installed Solaris 10 many times ,sometime GRUB detected Windows XP automatically and other times it could not and other times it halted during installation and said I/O error could not install all packages ,so i changed my CD-ROM anyway it did install Solaris 10 some times but GRUB could not detec Windows XP automatically and i could not configure GRUB to do so manually so i bought a new CD-ROM and mounted it on my pc.anyway when i tryed to install Solaris 10 and choosed Solaris from the booting screen it displayed the above mentioned error:
Error 28: Selected item can not fit into memory
the upper memory in the booting screen was: 752576 kb
lower memory: 639 kb
don't know but Solaris 10 is not making any sense to me since a week ,it's behavior is not understood .although i did run the install check before starting the installation and it did say Soalris 10 can be installed on you system.my hardware information is the following:
Gigabyte mother board with bult in VGA ,Sound ,Ethernet
40 GB Western Digital Hard Disk
750 MB of RAM's
Pentuiem 4 ,1 MB Cache
please adivce if anyone knows about this?

I was trying to fix this for more then 2 weeks , finally the solution to fix this was easy: GRUB new version 97 is crab ( sorry why i do not know but .. )
I have one disk with: windows xp and second part for fedora
I got the error after upgrading to fedora 6
I got GRUB 97 version with this fedora 6 automatically installed
and while booting on disk :
Error 28: Selected item could not fit into memory
all forums are explaining that it is not possible to boot via GRUB on a 2 nd partion to Linux ( fedora) because of 1024 constrains etc.
I can tell you that after installing GRUB version 92 in a fedora on the harddisk ( 2nd part) started via rescue cd
I installed the GRUB older version 92 forced to overwrite the GRUB version 97 on this partion of fedora
run grub via recue cd but run version 92 installed now
via command
/mnt/sysimage/sbin/grub
root ( hd0,1)
setup (hd0,1)
it installs grub on the boot record
and now I can boot without any problem on this GRUB in the boot record of the 2nd part of the disk
I use GAG on the MBR and GRUB ( version 92) on the boot record of Fedora partition and now it starts easy , no problems anymore
good to know, but it took some time to find it

Error message iPhone 5s could not be synced because the sync failed to start

My iPhone 5s will not sync i get the error message "iPhone 5s could not be synced because the sync failed to start"
running IOS 7.1.2
Macbook Pro running 10.9.4
iTunes 11.3.1.(2)
i did not load any new apps this just started. Thanks.

Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)

Runtime error Screen "SAPLXQQM" 0100 could not be generated.

Similar Messages

Maybe you are looking for