RV016 forwarding from both WANS

I've got port forwarding setup on an RV016, but it is only working from WAN2. Any incoming traffic on WAN1 doesn't get forwarded. I got the impression that forwarding rules apply to both WAN ports? Multiple subnets are enabled, with WAN2 being allocated a subnet that (ironically) the forwarding isn't going into. I've also tried UPnP (for port redirection, with UPnP disabled), but no joy. Anyone got any ideas?

If you have multiple subnets enabled and your forwarding to address is outside of the subnet for WAN2, that may be the problem right there since there's no gateway that the incoming packet to WAN2 can use.
I've used a setup like this before with multiple forwards from differnent WANs to a single server, but everything was on the same subnet.
Huntsville's Premiere Car and Bike e-magazine: www.huntsvillecarscene.com

Similar Messages

Rv320 - port forwarding from a specific WAN IP

Hi, i just received and configuring the rv320 router. I can successfully set the port forwarding from WAN to specific LAN IP address. I would like to know is it possible for this device to set the port forwarding from a specific WAN IP address? Thank you for the help.

I have the same problem, and have already tried creating a Access Rule without success. I need to forward Remote Desktop Port 3389 from a specific public IP address to a internal server. I do this with other lower-level Cisco Small Business routers all the time, but cannot get this to work with the RV320. Here's what I've tried:
1) Create new Access Rule
2) Create new Service called TS for TCP port 3389-3389
3) Set new Access Rule to Allow
4) Set Source Interface to Any (I've also tried WAN1, etc.)
5) Set Source IP to the only single public IP that will be allowed
6) Set Destination IP to the single internal IP address
7) Set Scheduling to Always
When I use any standard RDP app from the outside, the router blocks 3389 access.
What am I missing? Can anyone help resolve this, or do I need to call in to Cisco Support?

Can't configure both WAN ports on 1811 with SDM

Hi,
We recently procured an 1811 router to replace a SOHO linksys at a store we service. We needed redundant WAN interfaces to use the DSL as a backup to the main cable connection, and a Linksys RV082, while doing the job when it actually worked, died repeatedly. We decided after looking at the 1811's feature set to just get the Cisco and be done with it and not monkey with SOHO gear anymore.
Where I'm having difficulty is SDM won't let me configure both WAN interfaces from the GUI, it only allows me to configure one. I have it configured, and the router is working nicely in the test lab but I need to get that other interface configured and failover enabled before I can put this thing into production.
What am I doing wrong? Do I need to suck it up and learn IOS?
Thanks,
Todd Phipps
Certco, Inc.

I ended up figuring out the IOS commands to enable one fastethernet port as a primary and the other one as a backup (running both cable and DSL for redundancy; it's a grocery store that runs electronic transactions over IP so 100% availability is a must).
The trouble I was running into in SDM is that while it would allow me to configure one WAN port through the GUI, the config options for the second one were grayed out. Now that both are configured through IOS the edit buttons for both WAN interfaces appear normally in SDM. It's almost as if Cisco didn't want users to be able to configure both interfaces graphically for initial setup.
Now just to test it at the site before the store opens to see if the failover works...
Todd

How to do port forwarding from wla2-g54l Buffalo bridge to mac mini

Hi,
I am trying to get Azurus to remove the "firewall block" message and I think I have narrowed it down to port forwarding.
I have set up port forwarding from my X modem to the Airport Xpress base station. I have then set up the port forwarding from the base station to the buffalo.
The problem I have had is setting up the wla2-g54l to forward the same port to the mac mini....
any Ideas? Not much luck on the Buffalo website.. and I have RTFM. Many times!
Cheers
Mac Mini G4 1.2Gz Mac OS X (10.4.8)

It sounds like your set-up is in a horrible mess with 3 levels of NAT going on.
What you should really have is the X-Modem configured in it's default mode "Modem Mode" where there will be no need to do any port forwarding as the modem is acting as a pure modem without having any influence over ports.
Then the Airport express should be configured to "Distribute IP addresses" so that the Airport is acting as a router. I presume that you use the Buffalo unit as a repeater for the AIrport so you should set-up WDS so that both are on the same network. Then your computers will all be using IP addresses in the 10.0.1.x range as issued by the Airport. You can then configure the Airport to directly forward ports to the IP address of your computer. Therefore only one instance of NAT and only one set of port forwarding rules.

"How to forward from a struts form to a login page?"or "how to connect form

Can Any boby please let me know
"How to forward from a struts form to a login page?"or "how to connect form to login session id"?
Thanks
Shailajakrishna

I believe I can not use a
request.sendRedirectURL("....") in which I would
encode all my parameters, because:Righto. This is a bit tricky.
Basically, you have two options, and both of those are a little nasty.
1) You could use and intermediate JSP page. Just dispatch you request to that page, use the attributes to construct a form with hidden fields, and use Javascript to POST that form to your intended URL on the document's BODY onload event. Would work, but wouldn't be pretty and requires you to use JSPs and Javascript. Still an idea.
2) This is something that I wouldn't recommend. Open a socket to the URL you you want to post your data. Manually construct a HTTP POST request, encoding your parameters into the headers. Read and parse the response & modify your HttpServletResponse object accordingly.
Take a look at i.e. http://javaalmanac.com/egs/java.net/PostSocket.html?l=new for some pointers.
I'd go with item #1.
For my own edification, I'd be also interested in
knowing why such a function does not exist in the
current httpServletRequest api.I suppose it's a little out of scope. Servlets were ment to interoperate inside one container, not across domains and different implementations.
I'm guessing I must be missing something fundamentals
maybe?No, you're not.
.P.

Why can't I automatically forward from Apple Mail to Gmail?

Why can I no longer automatically forward mail from Mac Mail to Gmail account automatically. This worked fine till a few days ago but no longer. I hadn't changed any settings. have asked about this in Gmail forum but no useful answers, I have now changed various setting but makes no difference. Most of the Gmail help is oriented to Mail 4.0, I have 3.6, so that doesn't help (can I upgrade, I have OS10.5.8), I uploaded MailUpdate but it would it wouldn't let me install).
Maybe there is a way via Mail Forward but that seems for forwarding _from_ webmail _to_ Apple Mail.
All help gratefully received.
Thank you,
Michael
Model Name:    iMac
Model Identifier:    PowerMac6,3
Processor Name:    PowerPC G4 (3.3)
Processor Speed:    1 GHz
Number Of CPUs:    1
L2 Cache (per CPU):    256 KB
Memory:    1.5 GB
Bus Speed:    167 MHz
Boot ROM Version:    4.7.8f1

I suppose Gmail is forwarding to Apple Mail but not v versa, hardly anything at all is landing in Gmail.
My Apple Mail is a POP account, but IMAP -enabled in Gmail if that makes sense, Gmail help says that's what you should do to forward from POP to Gmail.
I want to forward them to Gmail so I can read my POP mail on my PC at work, as I said this worked beautiflly since I started in Feb till last week, then stopped for no apparent reason... As alternative I use mail2web which is just about okay but very slow, no outbox, no spam or other filtering, keeps timing out.
Yes something is doubling up but not sure what...
In my Apple Mail I have two accounts, both POP, one my regular apple mail account, the other my Gmail account, but settings are different according to Gmail help but not sure if they are right any more..
thanks again

Forward from action directly to anther action

Hi all,
I have the following problem: I have a pageflow application for administering complex configuration. On the main page (where user is forwarded from begin action, begin action reads data from configuration and fills them into form bean and main page displays them) is link for editation of part of configuration, link references to editaction which fills formbean and forwards to form for partial editation. This form submits to saveaction which stores data, and forwards to begin action directly. And here is the problem, somewhere in the portal framework between invocation of saveaction and begin following error is written into log.
25 X 2006 16:55:58,560 ERROR ArrayIndexToken [ExecuteThread: '13' for queue: 'default'][]: Could not update expression because a public field named "operation" or setter for the property "operation" could not be found.
I think, that this is beause form data is submitted and handled by saveaction, but because than forward to begin happens, portal tries to to fill submitted form data into formbean of begin action as well, but this formbean is different one and doesn't have corresponding properties. Both formbeans are scoped to request.
In this particular case it causes no other problem than logging aforementioned error, but in other cases when property names would accidentaly match it may cause some problems with data, so I consider this beaviour as dangerous and want to avoid it.
So my question is, how to forward from action to action without passing form data which were already handled by first action?

The problem what I would like to solve is the following:
I have some information stored on a DB. Depending of these information I would like to show different information on a jsp page with the help of jsf. (This jsp file is reached already with the help of navigation rules of jsf technology)
An action bean class is instantiated already when the generation of my jsp file started and the information are stored on this object in member variables. There is a boolean variable among these stored information and if the value of it is true, then I would like to send the user "automatically" to another jsp file (using the navigation rules of jsf).
If I would not use jsf, then I would do something like the following:
I would store the value of the boolean variable into the session, and I would use a jstl "if " tag to ask the value of this variable and when it would be true then I would use a <jsp:forward...> to send the user to the next page.
My problem is I can not solve this with the jsf navigation rules?
If I try to do something similar with jsf than #{myClass.newPage} is not accepted by jsp:forward tag of course, but I do not know a solution instead of it in jsf.
Is exist a solution in jsf for it?
If not, how can I create a similar sequence?
vikot

ACE - probes sent from both active & hot standby?

Hi all
Can see that for a particular context, probes attached to a serverfarm are being sent from both the active & the standby ACE modules.
I had the presumption that only the active module would be sending probes.
Are probes being sent from both modules expected behaviour?

Hi,
Yes that is the expected behavior. When the failover happens LB should have the status of the server's under serverfarm for it to forward the traffic so both LB's probe the servers.
Regards,
Kanwal

How can I use home sharing between our iphones (create playlists from both accounts at once)

How can I use home sharing between our iphones, so that we can create playlists with songs from both of our libraries? We share a Macbook Pro (separate accounts) and each have the new iphone, but when I have my iphone and try to create a new playlist, I can only grab songs from one account. Is there a way to create a playlist using both accounts since we are sharing?
Does it have to be created within iTunes first on our Mac?

The short answer: because Home Sharing isn't designed for sharing apps, and apps aren't designed to be shared.
The longer answer: Think of it like this...
You download some music in iTunes. With Home Sharing, another user can listen to it by streaming it over the network. But the data itself is on your computer. If you turn off the computer or take it off the network, the other user can't access it.
But if you send another user the app, they aren't just streaming the data- they installed it on their iOS device. Because they weren't the one that purchased it, such a transfer could easily be considered "piracy" or "stealing," and nobody likes that (least of all, Apple).
When iTunes sees this app, it obviously recognized it, as if saying, "Hey, how did you get this app on your device, if I have no record of you purchasing/downloading it from the iTunes store?"
post edited to correct spelling errors

I am trying to update ITunes from 10.4 to 10.5 I have tried from both the program, and from a download on Apple's website. Regardless, I get the following error messages: (1) Installation package for iTunes cannot be found. Try installing to find the inst

I am trying to update ITunes from 10.4 to 10.5 I have tried from both the program, and from a download on Apple's website. Regardless, I get the following error messages: (1) Installation package for iTunes cannot be found. Try installing to find the installation package 'iTunes.msi' in a folder from which you can install iTunes. I can't find this folder. I have tried to completely unistall iTunes through the Control Panel, but it wouldn't let me: I tried going directly to the files themselves, but cannot uninstall. Any help would be greatly appreciated. System OS: Win XP SP 3.

Set the permissions for Everyone in the folder in which CCPackager created, to "Read/Write" enabled. This is strange since there is only an administrator account on the Mac (and that account already has read/write), but it seems to resolve the issue.

Sound coming from both speakers and headphones at the same time in probook 4440s

I have a Probook 4440s with windows 8 pro(64 bit) with IDT high definition codec installed. Yesterday when i was playing some songs i noticed that the sound was coming from both headphones and speakers even when my headphones are plugeed in and my lappy was having no such problems a few hours earliers while i was watching a movie. Please help..

It may be because you have both the internal speakers and headphones enabled at the sametime on your laptop. This might just happen automatically when you plug your headphones in. You need to manage your audio devices on your laptop.
Go to Control Panel> Hardware and Sounds> Manage Audio Devices> Playback Tab (which should already be selected)
In the playback tab there should be a list of all the audio devices you are using on your computer. Right click on the one you don't want to use and click disable. This should stop the sound coming from that audio device.
Remember: You will need to enable that audio device if you want to listen to sound through it again. Your internal speakers won't work once you enable them again. This might also be the case with your headphones. You may also have to do this every time your plug in a device or once you restart your computer.
Another note: Sometimes disabled devices will not show up on the audio device list so once you disable a device it will dissappear. This is an easy fix too. Just right click on an audio device and make sure show disabled devices and show disconnected devices is checked.
I hope this helps.
(I was using a computer with Windows XP to explain the instructions but it should be similar with your Windows Operating System. You may however have to play around a little on your computer because it may be slightly different)

Master Child tables how to get the latest rows from both

Hi,
Need some help with the sql. I have two tables Master & Child. In my Master table I have multiple rows for the same record and in the child table also multiple rows for the same master row how can I get the latest one's from both.
For example Data in my Master table looks like
CONT_ID                  SEQ_NUM        DESCRIPTION
1                         189             Update 2
1                         188             Update 1
1                         187              NewNow in the child table for the same CONT_ID I may have the following rows
CONT_ID                   UPDATED_DATE                                     STATUS
1                        3/16/2010 2:19:01.552700 PM                          P
1                        3/16/2010 12:29:01.552700 PM                         A
1                        3/16/2010 12:29:01.552700 PM                         P
1                        3/16/2010 12:19:01.552700 PM                         NIn my final query how can I get the row with seq_num 189 as it's the latest in Master table and from child table the row with status of P as it's the latest one based on the time. Here is the query i have but it returns the latest row from the child table only and basically repeats the master table rows as opposed to one row that is latest from both:
Thanks

Hi,
You can use the analytic ROW_NUMKBER function to find the latest row for each cont_id in each table:
WITH     got_m_rnum     AS
     SELECT     cont_id,     seq_num,     description
     ,     ROW_NUMBER () OVER ( PARTITION BY cont_id
                               ORDER BY         seq_num     DESC
                       ) AS m_rnum
     FROM    master_table
--     WHERE     ...     -- any filtering goes here
,     got_c_rnum     AS
     SELECT     cont_id, updated_date,     status
     ,     ROW_NUMBER () OVER ( PARTITION BY cont_id
                               ORDER BY         updated_date     DESC
                       ) AS c_rnum
     FROM    child_table
--     WHERE     ...     -- any filtering goes here
SELECT     m.cont_id,     m.seq_num,     m.description
,     c.updated_date,     c.status
FROM     got_m_rnum     m
JOIN     got_c_rnum     c     ON     m.cont_id     = c.cont_id
                    AND     m.m_rnum     = c.c_rnum
                    AND     m.m_rnum     = 1
;If you'd like to post CREATE TABLE and INSERT statements for the sample data, then I could test this.
If there happens to be a tie for the latest row (say, there are only two rows in the child_table with a certain cont_id, and both have exactly the same updated_date), then this query will arbitrarily choose one of them as the latest.

I use an Epson Stylus Office BX320FW printer with my IMac. Since upgrading OSX, I have lost the ability to print and scan. I have downloaded printer drivers from both Epson and Apple. I am using the printer in wifi mode but can not get it print or scan

Hi Everybody,
I use an Epson Stylus Office BX320FW printer with my IMac. Since upgrading OSX, I have lost the ability to print and scan. I have downloaded printer drivers from both Epson and Apple. I am using the printer in wifi mode but can not get it print or scan. How do I uninstall the Epson software and start all over again?
nickel_man_65

Not using any mouse pad, I have a very smooth desktop. But I just tried to use a sheet of A4 printing paper, but no result, the problem persisted.
Someone on this forum suggested, that USB3 may interfere with the magic mouse.
I have 2 LaCie HDD's about 70 cm away from the mouse, I use them on Thunderbolt. But in operation or not - the result is the same, the mouse plays up! Just now I was clicking the desktop and the mouse created a new folder!!
Thanks for the advice, Bee
Cheers, Gerd

I have two Aperture Libraries and would like to sync specific folders from both of them to my iPad.

I have two Aperture libraries stored on an external hard drive. Using iTunes on my Mac Book Pro can I sync selected projects from both Libraries to the same iPad?

No you cannot. Each device can only be synced with one photo library - Aperture or iPhoto.
You could however merge the two libraries, if you need to sync with photos from both libraries.

How do I merge two accounts into one account that contains all the files from both?

When I was running my MacBook Pro under Snow Leopard, I had one account for business that was encripted and another account that was unencripted for personal. Now, under Lion, the whole disc gets encripted so I don't really need two acounts. How do I merge the accounts together into one account and retain all the files from both?
Thanks,
Dave

Somethinkg like these?

RV016 forwarding from both WANS

Similar Messages

Maybe you are looking for