RV042 and Smart Link Backup

I have a RV042 with a pair of Cellular modems. They are connected, and managed with the "Smart Link Backup". The RV042 must also maintain a VPN to the home office. It has been in the field for about a month now. My 2 issues with this are:
1> not very easy to tell which WAN is active. Going thru the logs is no answer. This info should be displayed on the System Summary, not something which needs to be searched out in the logs.
2> the device is not "failing back". It fails over just fine. but, when the Primary is back online, it never returns. I suspect this has to do with the VPN and the "[ ] Tunnel Backup". My workaround for this has been to connect during "off hours", and just reboot the device.

Pyrthian,
1> Under Dual Wan>>> Smart Link Backup, which wan is set to Primary? This wan will take care of the traffic until it fails.
2>Under Network Detection Services the default Retry count is 5 pings and the Retry timeout is 30 seconds wait for the next ping. For testing purposes change this settings to retry count of 10 pings and retry timeout of 15 seconds. This will allow for more pings in a less interval time to detect traffic.

Similar Messages

Smart Link Backup Question

I have a RV042 small business router. I have the Dual WAN setup in Smart Link Backup mode.
WAN1 is setup for ISP 1 with a static IP Address and DNS servers specified.
WAN2 is setup for ISP 2 with a dynamic IP Addess (Obtain an IP automatically) with no DNS information entered.
If I unplug the cable for WAN1 the router switches to WAN2 fine. The problem I am having is that DNS fails on all of my computers until the cable for WAN1 is reconnected. If while the WAN1 is disconnected I do an ipconfig /release then ipconfig /renew on my computers, DNS lookups then function fine. If I then plug the cable back in for WAN1 I again have to do ipconfig /release then ipconfig /renew on my computers to again have DNS function properly.
Any ideas on how this can be fixed?

Sharon Grady wrote:Tekliu and Simon, I combined your two answers by using the OpenDNS servers in the DHCP Setup screen and then ipconfig /refresh ipconfig /renew on the computers. I then unplugged WAN1. And I was still able to resolve DNS. Thanks!!!!!
No problem, glad it helped you out
Regards Simon
http://www.linksysinfo.org

Rv042g need help to set up smart link backup

I had set up rv042g to Smart Link Backup mode. but sometimes wan1 link is "flashing". E.g. it has short time link downs which may last for a loooong period. And every time wan1 is up, router switches back immediately. this leads to fully unworking internet connection.
The question is: can i set up the time that router guaranteed will be switched to reserved link. for example it will be switched at least for one hour after wan1 is down?
Here is part of my log to illustrate the problem:
Jan 1 12:06:18 2010      System Log      WAN connection is up : 192.168.1.6/255.255.255.0 gw 192.168.1.2 on eth2
Jan 1 12:09:08 2010      System Log      NSD SUCCESS WAN[1]
Jan 1 12:09:08 2010      System Log      WAN connection is down
Jan 1 12:09:59 2010      System Log      NSD FAIL WAN[1]
Jan 1 12:10:00 2010      System Log      WAN connection is down
Jan 1 12:10:01 2010      System Log      WAN connection is up : 192.168.1.6/255.255.255.0 gw 192.168.1.2 on eth2
Jan 1 12:14:10 2010      System Log      NSD SUCCESS WAN[1]
Jan 1 12:14:10 2010      System Log      WAN connection is down
Jan 1 12:14:54 2010      System Log      NSD FAIL WAN[1]
Jan 1 12:14:56 2010      System Log      WAN connection is down
Jan 1 12:14:57 2010      System Log      WAN connection is up : 192.168.1.6/255.255.255.0 gw 192.168.1.2 on eth2
Jan 1 12:16:15 2010      System Log      NSD SUCCESS WAN[1]
Jan 1 12:16:16 2010      System Log      WAN connection is down
Jan 1 12:17:25 2010      System Log      WAN connection is down
Jan 1 12:17:27 2010      System Log      WAN connection is down
Jan 1 12:17:28 2010      System Log      WAN connection is up : 192.168.1.6/255.255.255.0 gw 192.168.1.2 on eth2
Jan 1 12:18:14 2010      System Log      recvfrom: Network is down
Jan 1 12:18:38 2010      System Log      WAN connection is down
Jan 1 12:18:50 2010      System Log      recvfrom: Network is down
Jan 1 12:18:52 2010      System Log      WAN connection is down
Jan 1 12:18:53 2010      System Log      WAN connection is up : 192.168.1.6/255.255.255.0 gw 192.168.1.2 on eth2
Jan 1 14:14:00 2010      System Log      WAN connection is up : 31.202.231.42/255.255.255.128 gw 31.202.231.126 on eth1
Jan 1 14:14:06 2010      System Log      WAN connection is down
Jan 1 14:14:14 2010     Kernel      last message repeated 2 times
Jan 1 14:14:15 2010      System Log      WAN connection is up : 192.168.1.6/255.255.255.0 gw 192.168.1.2 on eth2
Jan 1 14:17:09 2010      System Log      recvfrom: Network is down
Jan 1 14:18:28 2010      System Log      WAN connection is up : 31.202.231.42/255.255.255.128 gw 31.202.231.126 on eth1
Jan 1 14:18:32 2010      System Log      WAN connection is down
Jan 1 14:18:33 2010      System Log      WAN connection is down
Jan 1 14:19:01 2010      System Log      WAN connection is up : 31.202.231.42/255.255.255.128 gw 31.202.231.126 on eth1
Jan 1 14:19:08 2010      System Log      WAN connection is down
Jan 1 14:19:10 2010      System Log      WAN connection is down

Dear Roman,
Thank you for reaching Small Business Support Community.
I understand your concern and unfortunately I see no way to configure the failover the way you wish. Just in case you can contact the Small Business Support Center for further assistance;
https://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Please let me know if there is anything I may assist you with in the meantime.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

RV042 Smart Link / Failover is Sticky

RV042 in Router mode.
WAN1 preferred.
With Smart Link it seems to work to a point.
When WAN1 fails, it fails over to WAN2.
But then it gets stuck on WAN2 and I have to manually switch to WAN2 preferred and then back to WAN1 preferred to get WAN1 connection to return.
The test IP addresses should be just fine as set.
Is there something I should be doing differently?

I really appreciate the help. I think I would do better if I understood the definition and purpose and INTERACTION of those 4 entries.
Well, I can figure out "Default Gateway" ... I think. But maybe I don't understand the designer's context for this one even.
And, I tried entering the DNS Host and an IP wouldn't do so I put in the URL. I also think I can figure that one out OK.
Then there are: ISP and Remote Hosts.
According to the documentation with my comments at "***"
Default Gateway:
If you check this item, the Router will ping the default gateway first.
***OK. That's easy. But it doesn't say "you must check this item". So, I had not.
ISP Host:
After ping Default Gateway, the Router will ping ISP Host “Retry timeout" later. The ISP Host is provided by ISP.
***I guess I just pick an IP address belonging to the ISP or what? Or I could pick the public address gateway at the ISP.
Remote Host:
Enter the IP address of Remote Host that you’re going to ping.
***OK. So I could pick anything in the public address space that normally works, eh? But, does it necessarily have to be a public address? How about an upstream address in my network?
DNS Lookup Host: Enter the Host Name or Domain Name that you’re going to ping.
***Well, I wouild have thought that this means the host name of the ISP DNS server. But here it seems to say it can be almost any URL. Is the point here that it's a test of DNS service?
I think perhaps this will help reveal where I'm getting hung up. I should think that the design intends to test the closest connection first and surely failover if it fails. Then on to the next, and the next, etc.
If that's the case then I should think one could pick a single IP address to test and that's all. Is that correct. That's what I've been doing because I think that will effect the behavior I need.
I look forward to hearing more. Thank You!!

HTML Code for Smart Link Edit and Logout items

I am using an HTML template and would like to include the Smart Link Edit and Logout items in a TABLE. How do I do this?
Is there a way to get the code for these Smart Links (ORACLE tags) and include them?

According to Oracle Metalink "Note:368720.1 - When ILS is Enabled the Edit Smartlink is visible to Users that are not entitled to see it", that is the expected behavior whether you are using the "edit" substitution tags or the "edit" smartlink on a page when the page has item-level access enabled. I don't like it but I can understand why that is the behavior since an end user may have access to manage/edit just one item on a page or just one tabbed region on a page and they need a way to put the page into edit mode in order to edit their item(s). If a user has nothing to edit on a page, then they won't be able to do anything in edit mode anyway.
On the employee portal I work on, there is the possibility that every page may have a different set of users/groups that need to edit items/regions on the page AND the edit smartlink is published on the portal page template so basically, all employees can see the Edit link but if they click on it, only those employees that have items/regions to edit/manage will be able to really do anything while in edit mode.
However, on the customer portal I work on, there is only one group that manages content site-wide so I was able to publish the Edit smartlink on the portal page template and change its access to the one group that manages content so they're the only ones that can see the Edit link on every page.
The substitution tags for Logout are #PORTAL.LOGOUT.URL# and #PORTAL.LOGOUT.LABEL# (I use those so I can control the html & css) or just #PORTAL.LOGOUT# (which does both the label and url). The list of all substitution tags is available in Oracle Application Server Portal Help.

Series link and Smart Series

Until Sky stop prefixing programmes with the moniker NEW:, series link and Smart Series will not work because the planner thinks they are another programme. E.g. last night UNDER THE DOME restarted, and was set in my Smart series. Unsurprisingly, it did not record as the programme was called NEW: UNDER THE DOME.,...... Not technical, you can keep on rebuilding your planners all day, but the solution is obvious, except to Sky, no surprise there......

The 'new' issue (which was fixed I think in R010) never stopped programs recordings, it just mixed up the stacks if you had episodes both with 'New' and without. This has been fixed in the majority of cases.
Your issue appears to be entirely different. Did the next episode (ie last night's Falling Skies) appear in the Scheduled Tab at all and fail to record or didn't it put it in after last week's episode?
is correct in that it is up to the channels themselves what constitutes a series. For example, it is the BBC who has decided that the new Top Gear specials being shown are not part of the aborted series, so Sky boxes won't have picked them up automatically.

How are Level 0 and Level 1 backups linked?

Version:11g
I was going through the scripts in the post Two Questions on RETENTION POLICY
When you have a Differential Incremental backup strategy and When you run level 0 and level 1 backup scripts through different cronjobs from Sunday to saturday, during recovery, How will RMAN identify all these level 1 backups and its parent level 0 backup as one unit ? In the level 0 and its subsequent level 1 backup scripts, i don't see a clause which links level 0 backup and its subsequent level 1 backups?

Hi Steve_74,
How will RMAN identify all these level 1 backups and its parent level 0 backup as one unit ?The information used during a restore is comming from the controlfile.
Example
select BACKUP_TYPE, INCREMENTAL_LEVEL
from v$backup_set
Will determine the level 0 backup set needed according to your restore clause
select INCREMENTAL_LEVEL, INCREMENTAL_CHANGE#, CHECKPOINT_CHANGE#
from V$BACKUP_DATAFILE
where file# = 1
Will determine which incremental(s) to apply on datafile 1 according to your restore clause.
Regards,
Tycho
Edited by: tychos on Nov 1, 2009 1:51 AM

Basic tutorial shows adding a logo to lighthouse picture is easy, File + Place. I don't have "Place" in my dropdown. I only have "Place Embeded" and "Place Linked". What am I doing wrong?

Basic tutorial shows adding a logo to lighthouse picture is easy, File + Place. I don't have "Place" in my dropdown. I only have "Place Embeded" and "Place Linked". What am I doing wrong?

You are not doing anything wrong. The January 2014 update of Photoshop CC added the option to embed OR link Smart Objects. Until this Photoshop CC update, Smart Objects were always embedded in the Photoshop document. Although it made the file size larger, it was like a built-in backup plan because any placed files were included in the document. Now you have the option of embedding or linking the Smart Object. Linking references the file rather than actually copying it to your current file. In terms of your small tutorial, choose Embed.

What is the diff b/w Sap Scripts and Smart Forms

Hi,
Whats the diff b/w SAP Scripts and Smart Forms..
I need the internal explanation for both Smart Forms and SAP Scripts mean when we execute what happens whether Print Program r Forms starts execution 1st and SIMILARLY FOR SMARTFORMS WHETHER FM'S R FORMS.
Thanks & Regards,
Gopi.

Hi
Difference with SMARTFORMS vs. SapScript(SE71)
The Following are the differences :-
a) Multiple page formats are possible in smartforms which is not the case in SAPScripts
b) It is possible to have a smartform without a main window .
c) Labels cannot be created in smartforms.
d) Routines can be written in smartforms tool.
e) Smartforms generates a function module when activated.
f) Unlike sapscripts (RSTXSCRP), you cannot upload/download Smartform to your local harddisk.
It was said that it was provided in CRM 3.0 version, but not available in R/3. You can download smartforms into Local PC in a XML format. In the same way you can upload this XML format into Smartform. From the smartform editor itself you can call download option, if you are working in CRM 3.0 environment.
In R3 also, you can download into XML format. However, it's not sure about uploading. Refer to the program 'SF_XSF_DEMO'.
In 4.7 Enterprise, other have seen this utlity which is completey missing in 4.6c. There is functionality to downlaod a complete form or only a particular node. (Utilities -> Download form). It will create a XML file and save it in the hard disk.
For others, if you want to download/upload the Smartforms source, you will need the help from the Basis people. What you can do is to create a Transport and then FTP down to your local harddisk. When you need the Smartform source in another system, you have FTP up the Smartforms file back to the SAP server. Finally, the Basis team, will tp it into your system.
g) The protect and endprotect command in sapscript doesn't work with smartforms. For example on a invoice: First data of position no 80. is printed on page one, other data of position no 80 is printed on page 2. And there's nothing you can do about it. Actually, there is something you can do about it. By using a folder node and checking the 'protect' checkbox, everything in that folder will be page protected.
check out this link:
http://www.sap-img.com/smartforms/sap-smart-forms.htm
Reward points if helpful.
Regards,
Swathi.

If i selected to "Create a new backup" and then cancelled that option but want to go back and select "Inherit backup history"; how do i go back and do that since now when i plug in my HD, that option doesn't appear anymore?? Any Help?

If i selected to "Create a new backup" and then canceled that option but want to go back and select "Inherit backup history"; how do I go back and do that since now when I plug in my external hard drive, that option doesn't appear anymore?? Any Help? I bought a MacBook Air, but decided to return it for the newest model, and I wanted to back it up so that I can then back it up on my new MacBook Air. I didn't understand the option to Inherit or start a new back up, and therefore selected the option to create a new backup. I believe I should have selected to Inherit backup history so that when i back it up on the new MackBook Air, it appears the same as the one I'm returning.... Is there anyway that i can re-select the option to Inherit backup history for time machine?

Thanks for sharing this link.
I've posted a question here https://discussions.apple.com/message/22049103#22049103 describing my situation. Are you able to suggest me the right option?

List of script and smart forms(except TNAPR) with output type or print prog

How to find out List of SAP SCRIPT and SMART FORMS (except TNAPR)with output type or print program..I like to chk in output type WMTA whch form should use.kindly help on this

Hi
WMTA is special msg and doesn't create any print: so you can't find a sapscript or smartform to link to it.
WMTA is a message for delivery, so you can find it by NACE trx or TNAPR table (It's the same): infact here it can find only all messages of logistic modules (SD & MM).
The routine ENTRY of RLAUTA20 is called by WMTA and creates a Transfer Order (for WM, Warehouse Management, module), so if you need to create a print for that msg you need to change prg RLAUTA20,
Max

How to automatically update Smart LINKED Object

Hi.
This is my first post here, I'm French, so excuse any English mistake i may do.
I'm not an artist / designer / ..., still new about using image software editing like photoshop.
So i downloaded Photoshop CC to try it because i wanted to do something on my spare time.
I want to render digitaly a card collection based on a online Collectible Card Game (Duel of champions if you wanna know).
For this I downloaded their card art from their site.
Then i want to add several effect / filter to render them nicely.
So i read and watch many tutorial in this purpose.
I ended with a good result for 1 card.
Here is an example :
Hi.
This is my first post here, I'm French, so excuse any English mistake i may do.
I'm not an artist / designer / ..., still new about using image software editing like photoshop.
So i downloaded Photoshop CC to try it because i wanted to do something on my spare time.
I want to render digitaly a card collection based on a online Collectible Card Game (Duel of champions if you wanna know).
For this I downloaded their card art from their site.
Then i want to add several effect / filter to render them nicely.
So i read and watch many tutorial in this purpose.
I ended with a good result for 1 card.
Here is an example :
So what i did :
I get a source card art image, adding its red border, embossed it to get relief, adding a gloss effect in 3 different layers (the card art, the border and the gloss effect). Than i duplicate all this layers, swap them vertically and moved down to get a reflection.
I added a gradient to this new group of layers to have a nice fading effect to the reflection.
As I do not want to redo all the process again and again if I change main the source card Art, I want the reflexion to automatically update.
This was done using Smart object, both main source card Art and the (vertically swapped) reflexion card art using the same object storing my different main source card art.
So when i change in this object the main source card art used, it automatically change both the rendered card and its corresponding reflexion.
And then i Added a displacement filter to simulate a water reflection.
And the first problem (solved by now) occurred :
If i want to apply a filter to the group of layers corresponding to the rendered reflexion card, Photoshop have to convert and merged the whole group of layers into another new smart object and then apply a smart filter onto it. That worked but i lost the auto updating of the reflexion as the previous conversion have made Photoshop create in fact a whole new duplicated object storing a my different main source art.
So i partially resolved This by using Smart LINKED object instead of Smart object. I say partially because it is not really fully automated anymore.
Now if I change the main Source card Art to render a new one, I have to "manually" save file / update smart object to get the reflection updated.
I kinda accelerate this using a action performing a batch of saves to get a "save all" options (that clearly miss in photoshop). But for this i still have to open all my smarted linked object in order to apply the "Save All" batch.
But know I want to generalize the process to cards left, and render my whole card collection.
So i created a template based on what i've done so far using in this template Smart LINKED Object for the Main source card art and the reflected one. By the Way I exported the Reflection group in a PSD file, and refered to it as another Smart LINKED Object in my template. Doing so i'm sure Photoshop no more use a temporary PSB object correspond to the converted / merged reflexion Smart Object (remember : created in order to apply a smart Filter on it).
So what Happen now ?
I create a new testing psd file in witch i embed several new smart objects each one is an occurence to my template. Here i have to used smart Object and NOT smart LINKED Object because if so i'll always end up with the same rendered card several times. I have to get Phososhop create it own temporary duplicated object so a modification to one don't affect all the others after "Save All" batch on the corresponding working card.
So with what I have now, if I want to change 1 of the rendered card, i go its corresponding (duplicated) template object and from there i access again my LINKED object storing all my main source card Art.
I change to what source card art I want, and I have to open the reflection smart LINKED Object too in order to apply the "SAve All" batch.
Here is the "fun" (issue) thing : I have to apply the batch 3 time in a row to have the rendered card changed in my main testing psd file. I suppose saving 3 time time propagated the change along the Smart LINKED Object chain.
AND I have to make sure ONLY the corresponding smart (LINKED) Object file are opened before. If another file from a different rendered card is opened too the change will also be propagated to it and so having a duplicated rendered card. (I only want each card rendered once, but using the same template to avoid repetitive work).
So I explained in detail, but maybe not clearly, my situation and the step i went through.
TLDR
To summarize : I have a collections of Card art (jpeg).
I created a Template applying effect to render 1 card.
I created another template appliying same effect to render 1 REFLECTED card.
In both i use the same Smart LINKED Object that Store my collection on Card Art.
I make another Smart LINKED Object in the first template that reference the second one.
So with my first template I can update the rendered card and its rendered reflexion after changing the main source card art in the subsequent smart LINKED Object that store my whole cards art. I have to had all corresponding Smart LINKED Object file OPENED and save them all to have th updated result.
So not really automatic.
Then I want to render my whole card collection with effect and reflexion.
I create in my project a duplicate of my first template for each card to be rendered.
Then I have to open ONLY all subsequent corresponding Smart LINKED(or not) Object file of current working rendered card and change the main source card art, save all the file (several time to propagate change) to properlly update the current rendered card.
I have to do this for EACH of my duplicated template in order to render EACH of my cards.
Definitively not automatic process, and prone to errors.
Do you know a way to fully automatically render my card collection ? The only thing I want to do is chose one time the main source card art for each rendered card.
Finally another way to explain this issue and maybe get an answer is to instead explain simply what I want to do :
I have a collection of (jpeg) card art from an online card game.
I want to render them all with effect (gloss, emboss border, faded and water filtered reflection).
I want to do this automatically.
The only thing i manually want to do is chose the card art to be rendered for each of the card i want to render in my collection.
Here is an image of what i want based on what i've, not automatically, done so far :
Thanks for any help from photophop professional here.

Hi,
The delta load does not work for product categories but only products.So to bring in the new product categories into SRM you will need to start the load of the object DNL_CUST_PROD1 again.
The CRM middleware allows the following two methods for replication.
-Initial loads:
Launched manually (R3AS), the objects (customizing or business) are replicated between SRM and R/3, according to the filters you've put on the object (R3AC1 for Business objects like MATERIAL, R3AC3 for customizing objects like DNL_CUST_PROD0 and 1).
-Delta loads:
This option is only possible for Business objects, which is the case of MATERIAL.
With this option a daemon is launched between the 2 servers. Every modification made on an object on SRM or R/3 is transfered as soon as this object is contained in the filter retrictions (creation and/or modification). this is done through transaction R3AC4.
Also refer the foll thread:
Material group from R/3 to COMM_CATEGORY (SRM)
Related notes : OSS notes 872819 and 720819.
BR,
Disha.
DO reward points for helpful answers.

Diff bet Adobe forms and smart forms?

Hi Friends
What is the diff between Adobe forms and Smart Forms
Thanks & Regards
Kanni

Hello,
Smartform:
To create and maintain forms for mass printing in SAP systems. Besides using the printer for standard output you can also select the Internet (by using a generated HTML output), a fax, or e-mail as the output medium. Smart Forms allows you to execute simple modifications to the form and in the form logic by using simple graphical tools
http://help.sap.com/saphelp_srm70/helpdata/EN/16/a369b1800e4bdda978ee0fe3b7bd2c/frameset.htm
Adobe Form:
Interactive forms in PDF format that allow users to fill out the form on the screen and save their entries in XML format in the form. When the SAP system receives the PDF form, it extracts the data saved in the form, and can process it further.
http://help.sap.com/saphelp_srm70/helpdata/EN/f2/21021b911f4c0cae11459a4ce0bc62/frameset.htm
Links will provide more information.
Thanks
Ashutosh

Advantages of Adobe Form Vs Sap Scripts and smart forms

Hi All,
Can any body explain me clearly what are advantages of Adobe forms when compared to sap scripts and smart forms
Regards,
Venkat

Refer to two Links below you will get all your answer
/people/markus.meisl/blog/2006/12/22/a-pdf-form-or-not-a-pdf-form--that-is-the-often-the-question
https://www.sdn.sap.com/irj/sdn/adobe
Cheers
Satya

TS3682 I updated to a new phone.. Went to the PC to backup my phone and I get the corrupted backup message.. I go ahead and delete all backups for iPad and my iphone, restart everything from scratch and still get this message. What the hey is wrong?

I have replaced my old iphone. I had an older backup on my pc where I keep my ipad backup as well. I have also updated and verified that the new ios is correct.
Came home and decided to backup the old phone to recover photos, music, apps, etc...
Connecting the old iphone,I get the backup corrupted message that everyone sees.
I go into the backup directory and delete both backups, restart the itunes, restart the PC, and then reconnect my iphone to the pc whihc restarts iTunes.
Tried to backup the old phone again and still the same message...
So, this is the new world where you cannot backup a "smart phone"....
Anyone got any ideas as to what needs to be done?

thevoice wrote:
-Snip-
Connecting the old iphone,I get the backup corrupted message that everyone sees.
-Snip-
I've personally never seen this message.
And what it means, quite simply, is that there is corrupted data in your iPhone, so it will not let it make a backup so that the corrupted data does not get saved and passed on.
All you can do here is manually transfer your photos, contacts, calendars to your computer. And then transfer your purchases. You will not be able to make a backup.

RV042 and Smart Link Backup

Similar Messages

Maybe you are looking for