RV042 Dynamic DNS not updating automatically
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (
v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated.
I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save.
So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to "
Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save".
I've let the other RV042 go over 48 hours and it still hasn't updated.
So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring.
Does anyone have DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
I'd like to hear any suggestions on how I might be able to fix this, or if this needs to be fixed in the next firmware release. Hopefully, I've explained my problem clearly.
Jasbryan,
I am experiencing a problem with DynDns updater too. For me it seems that the updater (after a public IP change or reboot) only tries to update once, and if it failed then gives up and never tries again.
I have to update manually (pushing the update button) which sooner or later succeeds. (Sometimes the first trial is successful, sometimes only the second or third.)
I have an RV042 (v3) with firmware at 4.1.1 and a DynDns Pro subscription.
I have a site-to-site VPN between two RV042s, both with dynamic IP. When the VPN tunnel drops, I usually detect that one of the public IPs has changed and the router for some reason failed to update DynDns. If I do it manually pushing the update button (one or more times), the tunnel comes up of course.
Again, I suspect the problem is with the updater's "strategy" and timing. Should it wait a bit more after detecting a new public IP and retrying in every 5-10 minutes after a failed update attempt it would be more reliable.
Janos
Similar Messages
-
Dataset not updating automatically
Hello,
I have a graph that is dynamic. I already have a variable set up and also a dataset. This file is saved.
Basically, I am trying to write some code that will open the document, import the variable file (with the new data from the xml file) and then update the graph.
Using the code below, the file opens and also the import of the variables is succesful. However, the graph is not updating automatically. I need to actually select the value from the dropdown in the variables window. Can anyone please tell me what I am doing wrong.
// Open the file and import the datasets and variables from xml file
var docRef = open(new File(aiChartFilePath));
alert("Importing the datasets.");
docRef.importVariables(new File(xmlFilePath));
var ds1 = docRef.dataSets.getByName("Chart1Variable");
alert(ds1); //this gives the "DataSet Chart1Variable"
docRef.activeDataset = ds1;
ds1.display();
redraw();
rs = "OK";
Thanks in advance for your help.this should work just fine ... put 2 datasets in the same file:
<?xml version="1.0" encoding="utf-8"?>
<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 20001102//EN" "http://www.w3.org/TR/2000/CR-SVG-20001102/DTD/svg-20001102.dtd" [
<!ENTITY ns_graphs "http://ns.adobe.com/Graphs/1.0/">
<!ENTITY ns_vars "http://ns.adobe.com/Variables/1.0/">
<!ENTITY ns_imrep "http://ns.adobe.com/ImageReplacement/1.0/">
<!ENTITY ns_custom "http://ns.adobe.com/GenericCustomNamespace/1.0/">
<!ENTITY ns_flows "http://ns.adobe.com/Flows/1.0/">
<!ENTITY ns_extend "http://ns.adobe.com/Extensibility/1.0/">
]>
<svg>
<variableSets xmlns="&ns_vars;">
<variableSet varSetName="binding1" locked="none">
<variables>
<variable varName="Variable1" trait="graphdata" category="&ns_graphs;"></variable>
</variables>
<v:sampleDataSets xmlns="&ns_custom;" xmlns:v="&ns_vars;">
<v:sampleDataSet dataSetName="Capella_1">
<Variable1>
<data numDataColumns="2">
<propertyRow key="name">
<value></value>
<value>ClassA</value>
<value>ClassB</value>
</propertyRow>
<values>
<row>
<value key="name">RowA</value>
<value>1</value>
<value>4</value>
</row>
<row>
<value key="name">RowB</value>
<value>6</value>
<value>2</value>
</row>
<row>
<value key="name">RowC</value>
<value>8</value>
<value>5</value>
</row>
</values>
</data>
</Variable1>
</v:sampleDataSet>
<v:sampleDataSet dataSetName="UPD">
<Variable1>
<data numDataColumns="2">
<propertyRow key="name">
<value></value>
<value>ClassA</value>
<value>ClassB</value>
</propertyRow>
<values>
<row>
<value key="name">RowA</value>
<value>1</value>
<value>4</value>
</row>
<row>
<value key="name">RowB</value>
<value>6</value>
<value>2</value>
</row>
<row>
<value key="name">RowC</value>
<value>8</value>
<value>5</value>
</row>
</values>
</data>
</Variable1>
</v:sampleDataSet>
</v:sampleDataSets>
</variableSet>
</variableSets>
</svg>
Javascript code:
var DBHelper = {
mainFs: null,
loadFile: function(fileOrFilename, isAI) {
var _fl = (fileOrFilename instanceof "File") ? fileOrFilename : new File(fileOrFilename);
if(isAI) { myDoc = app.open(_fl);}
else {
myDoc.importVariables(_fl);
this.mainFs = app.activeDocument.path.fullName + "/" + app.activeDocument.name;
myDoc.save();
myDoc.close();
this.loadFile(this.mainFs,true);
displaySet: function(setName) {
app.activeDocument.activeDataset = myDoc.dataSets.getByName(setName);
app.activeDocument.activeDataset.display();
DBHelper.loadFile("/d/_temp/Capella_Chart_1.ai", true);
DBHelper.loadFile("/d/_temp/variables.xml",false);
DBHelper.displaySet("Capella_1");
cheers; -
Time stamp does not update automatically
Hi, All. I want include the time stamp (yyyy-mo-dd-min-sec) in the file name. However, the value of the time stamp does not update automatically/synchronizes with the computer clock at each new run. I need to do it manually with the right click and update the time to the current.
How can I solve this? Thanks a lot in advance.What does this have to do with NI counter/timer hardware?
What language are you using and what function are you using to get a timestamp? If the language is LabVIEW, then all you need is Get Date/Time in Seconds. If you are using a front panel Time Stamp control, then you are using the incorrect function. -
How can I solve the problem în the subject?
How can I solve the problem în the subject?
What exactly are you trying to do?
Have you been editing photos in iPhoto and want to add them to your camera rool or photo stream?
Then do exactly as the article describes, that you lonked to:
iPhoto for iOS: Photos in Camera Roll are not updated automatically with edits from iPhoto
Use iPhoto's Sharing to save a copy of the edited photo to the Caera Roll, or explain on mor e detail, what you want to do.
Regards
Léonie -
Dates in Events do not update automatically
After iPhoto made events out of my photo library during conversion from from iPhoto06, there are often photos from several days in one "event". I can live with that most of the time, but in several instances I split events. Unfortunately, the dates of the original, unsplit event do not update automatically. This often results in a wrong order of events. If, e.g. I take out pictures from August 10th from an event with photo dates August 10th to August 13th, the original event still shows the starting date of August 10th, and orders the event between August 9th and August 11th.
The expected behaviour would be that the starting date of the modified event would change automatically to reflect the changes. This does not occur, and, worse, there is not even a possibility to change those dates manually.
Am I missing something important here, or is this an VERY annoying bug in iPhoto08?I agree - but this is a user forum and we can NOT fix anything - only try to help either follow the correct procedures of (as in this case) identify a work around to use until Apple fixes the problem.
As far as I know the work around of creating a new event form one photo and moving the remaining photos to the new event is the ONLY way arround this problem right now.
Using the work around will accomplish what you need even though it should not be necessary. Complaining about on this forum will not accomplish anything - compalining directly to Apple might -- iPhoto menu ==> Provide iPhoto Feedback.
Larry Nebel
PS - and reading the thread prior to get the work around prior to adding "I have the same problem" would actually be a pretty good idea too! -
Passbook does not update automatically
passbook not updating automatically i have to go to each app and manually add updates.
The only updates are those of amounts for Starbucks, since that is the only one I can comment on. Is that what you are referring to, is the amount, or the number of cards? You didn't answer my other question. If you update the amount in your card, either by purchase to decrease, or reloading to increase, it is those amounts that are not updating? Is this correct? If you purchase a new card, it will not automatically be added to Passbook, you have to manually add it. Since I don't have the Cub foods app, can we just concentrate on Starbucks, since I have it and use it regularly. I will be able to understand what you are doing and maybe not doing that way. To be honest, at this point, I'm still not sure exactly what you are doing.
-
RG1 is not Updating Automatically
Dear All Salute !!
RG1 is not updating automatically in the system due to data migration on cutoff date since February; they are maintaining parallel in the legacy system (in Excel or any other), though here is updated project from 5.0 to 6.0.
I am unable to understand, how the system is going on in the lacking of this.
From Accounts Department side: Still Cenvat duty posting & statement (57AE) are done manually by dispatch/stores department. As per ECC6, system generated report should be available to the end users to avoid duplicate work & mistake.
As per observation from SD side _no Opening Balance is uploaded while data migration_.
I have got information through SDN about table J_2IRG1BAL but I am unaware of using this.
Please provide me complete solution for this to do the needful instead of OSS Notes.
Rgds
Srivastav
+91-9973504950Adding to Komals reply,
Please go through the sap note 951955 and check below comments:
Please check whether you have maintained opening balances for
all RG1 material in table J_2IRG1BAL. If not, please maintain opening
balances for all RG1 material in J_2IRG1BAL for the date from which
you want to run the RG1 report.
Thanks
Murtuza -
Statistical delivery date is not updating automatically or by default
When creating the PO delivery date of a item in PO,is picking,but statistical delivery date is not updating automatically or by default. I am not getting this automatically .Its need for vendor evaluation.
Hi,
Check on it:-
Statistical Delivery date vs Confirmed Delivery date
pherasath -
Hi, My iPad has iOS 5.1.1 and is not updating automatically. Yes I reconfigured as it came yesterday
Hi, My iPad has iOS 5.1.1 and is not updating automatically. Yes I reconfigured as it came yesterday
I thought about that, but where he states that "Yes I reconfigured as it came yesterday," I assumed that this was a new iPad 2 that he just received yesterday. The tagline shows iPad 2, FWIW.
However, your assumption may be probably is correct. -
My devices, iPad and iPhone, are not updating automatically with pages. Any suggestions. They use to update beautifully about one week ago. I took my MacBook Pro to the Apple store for software issues, and I been having updating issues. Little help please.....
Welcome to the Apple community.
Check all your devices still have documents and data syncing turned on in settings > iCloud and that iCloud is enabled at settings > Pages. If this doesn't help, reset documents & Data from a computer at...
iCloud.com -
ITunes: podcasts are not updating automatically
Hi,
My podcasts are not updating automatically in iTunes as they as they should.
My Mac and iTunes are running 24/7, so iTunes it always running. The update interval of the podcast is set to hourly, latest iTunes, latest Mac OS X.
The podcast actually does update if I re-start iTunes or, if I manually update the podcasts (there is always the latest 1 or 2 daily episodes of say NBC nightly news available, but not yet downloaded)... (but this is not a great solution as I am using iTunes through Plex, the Mac is mor a TV/Mediacenter for my family; Plex can access playlists and podcasts in iTunes, but obviously it cannot trigger iTunes to update, so I have to go out of Plex to update iTunes, very annoying)
How can I ge my my podcasts to be downloaded automatically by iTunes.
Thank you for any help!Here is a screenshot of the phenomenon/problem... NBC Nightly News is not updated, even both the computer and iTunes are running constanly. Once I click update podcast, the podcast updates, so there is an update available.
-
I have done all the steps required to update IOS5 to my iPhone. It did not update automatically. It just updates to 4.2.1 which says is the latest software for my iPhone. Is there any other way to update my iPhone to IOS5?
I checked all the posts regarding this, it seems I have a 3G. Only found out now how to check my model. Thanks for your reply.
-
OS X 10.6.1: bootpd, named, and dynamic DNS zone updates
I have OS X 10.6.1 installed on a Mac Pro. It is configured to be the name server and DHCP server for my home network, i.e. /etc/named.conf and /etc/bootpd.plist have been modified to provide these services.
I've encountered no problems with either the name server or the DHCP component of bootpd after upgrading to OS X 10.6(.1); however, one thing that continues to bug me is how to configure bootpd to dynamically update the DNS zone files whenever a lease is issued, released, or expires.
At work, I use the Internet System Consortium's DHCP software and have it configured to dynamically update DNS whenever leases change state. I would really like to have DNS done the same way at home.
What changes need to be made to /etc/bootpd.plist that would allow dynamic DNS updates to occur?Did you ever get an answer to this? Would rather not change the DHCP server in Snow Leopard....
Thanks -
Bug: date inserted in cell does not update automatically
Can't find where to report a bug in Numbers. When I insert a date in a cell and set it to update automatically, it does not update. Have to update it manually daily. Seems there used to be a way to report bugs...
Anyone know how to do that now?Feature already reported.
+The Numbers User Guide states:+
+To add and format the date and time, place the insertion point where you want the value to appear, and then choose Insert > Date & Time.+
+To change the date and time format, Control-click the date and time value, choose Edit Date & Time, and then choose a date and time format from the pop-up menu. If you want the spreadsheet to always show the current date and time, select “Automatically update on open.”+
+Alas, under 10.4.11 *(and now under 10.6.1)* this feature doesn't apply.+
+The date remains as it was when we entered it.+
+Happily we have a simple workaround:+
+we may use the formula =TODAY()+
+But a feature wihch doesn't behave as described may be called a buggy one. Isn't it ?+
As long as the feature doesn't behave as described, use the given workaround.
Yvan KOENIG (VALLAURIS, France) samedi 12 septembre 2009 16:50:38 -
Firefox Sync does not update automatically when I add a new bookmark.
I use one desktop and one notebook at the same time. Firefox Sync does not update bookmarks between my desktop and notebook when I add a new bookmark from one device or the other. Firefox Sync only updates when I manually sync my data from each device. When I used Google Chrome, the Sync feature updated my bookmarks almost instantly. Is there any way I can make Firefox automatically sync whenever I update my bookmark?
Your imported bookmarks from IE should all be in one folder named "From Internet Explorer". The imported Bookmarks are kept separate for easier identification by the user. You can move them to other folders outside of that folder if you wish; you can also delete any duplicates that you may have placed into Firefox Bookmarks/folders before the import.
*See --> [https://support.mozilla.com/en-US/kb/Importing%20favorites%20and%20other%20data%20from%20Internet%20Explorer Importing favorites and other data from Internet Explorer]
For other Bookmarks info and links:
*See --> [https://support.mozilla.com/en-US/kb/how-do-i-use-bookmarks How do I use bookmarks?]
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''
Not related to your question, but...
You may need to update some plug-ins. Check your plug-ins and update as necessary:
*Plug-in check: https://www-trunk.stage.mozilla.com/en-US/plugincheck/
*Adobe Shockwave for Director Netscape plug-in: [https://support.mozilla.com/en-US/kb/Using%20the%20Shockwave%20plugin%20with%20Firefox#w_installing-shockwave Installing ('''''or Updating''''') the Shockwave plugin with Firefox]
*Adobe PDF Plug-In For Firefox and Netscape: [https://support.mozilla.com/en-US/kb/Using%20the%20Adobe%20Reader%20plugin%20with%20Firefox#w_installing-and-updating-adobe-reader Installing/Updating Adobe Reader in Firefox]
*Shockwave Flash (Adobe Flash or Flash): [https://support.mozilla.com/en-US/kb/Managing%20the%20Flash%20plugin#w_updating-flash Updating Flash in Firefox]
*Next Generation Java Plug-in for Mozilla browsers: [https://support.mozilla.com/en-US/kb/Using%20the%20Java%20plugin%20with%20Firefox#w_installing-or-updating-java Installing or Updating Java in Firefox]
Maybe you are looking for
-
Hi my husband has iphone 5 and has so many phobos on his deleted history.they can either have 3 or 4 numbers in front of them.are they certain websites or are they down loaded picture messages.please help as i would like to know why so many are on hi
-
Can't play HD .mov files (in Quicktime, iMovie, or FCP)
Hello, My Powerbook (bought in 2004) is senile and having various problems (see below for more details), so perhaps this issue can't be fixed without fixing the other stuff (or getting a new computer)... but just curious. I'm helping a friend with a
-
Unable to find analytics reports in bi publisher 11g
Hi, Want to create a report based on Oracle BI Analysis in BIPublisher. Trying to create a datamodel by selecting Oracle BI Analysis as data source. But unable to find analytics reports. Thanks.
-
BPM 11.1.1.5.0 Features Pack: UCM integration issue
Hi all, I have installed BPM SP4 FP successfully on Windows. But I have a problem with UCM integration. In Jdev, I configured the Human Task use UCM to store the documents. But after deploying on WLS, in BPM workspace, I cannot use attachment functio
-
Disable right click for all users in a certain group
I would like to disable the right click function for all users in a particular group, regardless of which computer is the domain they log in to. Is there any way to do this? Thanks.