RV042 - limiting HTTP access by IP address?

I am trying to limit HTTP access to my server on the local network to a specific IP address.  I create an Access Rule in the firewall section, however that doesn't work.  The only way it works is if I add the internal IP address of the server to the Forwarding section where I create a new HTTP forwarding rule.
However, that is not good because that allows ALL HTTP traffic to that server instead of just by the single IP address.
Anyone know how to do this?  Any help would be greatly appreciated.  Thanks in advance.

Thanks for the reply.  You are correct - I want to allow 1 specific external IP address to access an http server on my LAN.  Looking through those threads, it seems like the other use enabled one-to-one NAT.  I tried turning it on but it gave me an error message (I forgot what the error was, but it was something along the lines of the external IP address already being used in the Basic Settings or something).
I will double-check the error message and will post it here.  The current access rules are:
Deny: All services, WAN, All external, All internal
Allow: All servifces, LAN, All internal
Thanks for any additional help.

Similar Messages

  • AP521 HTTP access

    I am using 3 AP but I can not access to all AP AIR-LAP521G-E-K9 via HTTP.Do I need some configration to use HTTP access?
    However I can edit some configration from WLC526.

    yes, but I could not find that configration
    (Cisco Controller) >?
    clear Clear selected configuration elements.
    config Configure switch options and settings.
    debug Manages system debug options.
    help Help
    linktest Perform a link test to a specified MAC address.
    logout Exit this session. Any unsaved changes are lost.
    ping Send ICMP echo packets to a specified IP address.
    mping Send Mobility echo packets to a specified mobility peer IP address.
    eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
    reset Reset options.
    save Save switch configurations.
    show Display switch options and settings.
    test Test trigger commands
    (Cisco Controller) >config ?
    advanced Advanced Configuration.
    (Cisco Controller) >config advanced ?
    802.11a 802.11a parameters.
    802.11b 802.11b parameters.
    client-handoff Auto handoff the clients on excessive retires.
    dot11-padding Configure over-the-air frame padding
    eap EAP (Extensible Authentication Protocol) Settings
    macfiltering Configure advanced macfilter settings.
    max-1x-sessions Maximum 802.1x session initiation per AP at a time.
    probe-limit Limit number of probes sent to switch per AP slot per client in a given interval.
    rate Enable/Disable switch control path rate limiting.
    statistics Enable/Disable switch port statistics.
    timers Configures system timers.

  • VPN and limiting internet access

    I posted this under the SMB as well but wanted to post under the VPN header at the same time.
    Hello all, I am very new to VPN's and Firewalls so please forgive me for lack of terminology usage.
    I am part of a company that has 20 internal PC's and 25 external sites (Convienient stores) that are all now being placed on a VPN. We purchased a ASA 5510 for the office and we are placing Linksys RV042 routers at the stores. What my question is, is that we have a few stores that need limited internet access because we have Subway restaurants there and they need to download and upload at times. What I dont want is to allow full access to the net because of the chance of outside attacks or viruses.
    My question is, what can be done to set the VPN in place but only allow certain access to web addresses that we say is alright to have communication with?
    Is this possible and / or what else needs to be purchased?
    I thank you in advance for any help you can advise on.
    JJ

    The problem with the internet is, how do you define this 'certain' addresses. Is this possible for you?
    There is an option in VPNs called split tunneling, which has a "Exclude specified" mode, that might help.
    Regards\
    Farrukh

  • TS2690 How do I access my AOL address book where my groups are stored?

    How do I access my AOL address book & groups list to send or forward emails

    Natively on iPad you can not send to groups.  There apps in the App Store which you can get for this.  Here is one that may work for your needs:  http://itunes.apple.com/us/app/mailshot-group-email-done/id410279354?mt=8

  • How do I over-ride a secure connection failure to access the IP address for my wirelss router?

    I have a Linksys WRT54G wireless router. Yesterday all wireless functionality dropped out. I tried going to the router's IP address and got this message:
    Secure Connection Failed
    An error occurred during a connection to 192.168.1.1.
    You have received an invalid certificate. Please contact the server administrator or email correspondent and give them the following information:
    Your certificate contains the same serial number as another certificate issued by the certificate authority. Please get a new certificate containing a unique serial number.
    (Error code: sec_error_reused_issuer_and_serial)
    I searched for this message in Firefox help and tried the steps listed on:
    http://support.mozilla.com/en-US/kb/Certificate%20contains%20the%20same%20serial%20number%20as%20another%20certificate
    But it did not work. I could not access the IP address. I needed to do so, to reset and re-secure the wireless router. I was able to do this in IE because there is an option to ignore the warning. I would like to be able to access the router in Firefox.

    Delete the certificate in servers and authorities.
    Enter URL about:config
    Change browser:ssl_override_behavior to 1
    Accept the certificate again

  • How can I access alternate email address?, How can I access alternate email address?

    How can I access alternate email address?, How can I access alternate email address?

    I can't see why Tokyo should be a problem - rather the reverse given the Japanese commitment to technology. Can you get at http://icloud.com ? (Remember that you can't access that on an iOS device). Or you should be able to access it in your Mail app or application - what sort of problems are you having?

  • My children's iPod can get access to icloud addresses. How can I stop this?

    My children's iPod has no contacts and no access to icloud data etc but yet on email they can still get access to icloud addresses. How can I stop this?

    I recommend that you
    Create a NEW account/ID for her using these instructions. Make sure you follow the instructions. Many do not and if you do not you will not get the None option. You must use an email address that you have not used with Apple before. Make sure you specify a birthdate that results in being at least 13 years old
      Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card
    More details of how:
    http://ipadhelp.com/ipad-help-tips-tricks/how-to-get-free-apps-from-the-app-stor e-without-a-credit-card/
    Use the new ID on her iPod but only for:
    Settings>Messages>Send and Receive
    Settings>FaceTime
    Settings>GameCenter
    and Settings>iCloud    
    Continue to use the same/common Apple ID for Settings>iTunes and App stores so you can share purchases.

  • Sharepoint foundation 2010 externel https access problems

    I have a very strange problem with my sharepoint foundation 2010 site.
    I have a site which is accessible from outside on https (we have a valid certificate). I configured IIS for http and https.
    Also I configured internal and externel access for this site on sharepoint.
    But sometimes, the site is not accessible from outside on https with (externe.site.fr), BUT  it will be accessible with public ip !!!
    And also accessible from inside. (with interne.intranet.site.fr)
    Any Idea ?
    thanks

    Hi,
    According to your post, my understanding is that your site is not accessible from outside using external host name with https sometimes.
    As your site can be accessible with public IP, however it can’t be accessible from outside using external host name with https sometimes, the issue could be caused by the gateway server in your environment.
    I suggest that you need to check the gateway server configuration.
    For more information, you can refer to:
    http://community.bamboosolutions.com/blogs/sharepoint-2013/archive/2012/12/05/how-to-set-up-microsoft-forefront-unified-access-gateway-environment-for-sharepoint-2013.aspx
    http://nhutcmos.wordpress.com/2013/07/26/configure-ssl-certificate-for-sharepoint-external-https-access/
    http://sharepointdotnetwiki.iblogger.org/2009/12/dns-setup-in-sharepoint/
    http://underthehood.ironworks.com/2010/06/making-a-sharepoint-2010-site-externally-available-alternate-access-mappings-host-header-bindings.html
    Best Regards,
    Yumi Fu

  • I received a text today while at work about iCloud keychain verification code. I have not signed up for it or anything that uses it. I work out of the city with limited internet access so not sure why I would be getting this. Is my info safe??

    I received a text today while at work about iCloud keychain verification code. I have not signed up for it or anything that uses it. I work out of the city with limited internet access so not sure why I would be getting this. I only got this number about a month ago. Apparently someone else had the number before because I get texts from his family members wondering whats going on. I got one yesterday and the person didn't seem to thrilled that the number was cutoff and today I got 2 texts about iCloud Keychain which I don't even know what it is. Seems suspicious to me. If the person who use to own the number is doing it he should know it is not his number anymore because he obviously didn't pay his bills.  I'm not too sure about iCloud Keychain so just want to know my info safe?? It says it can store credit card numbers which is what gets me worried. Frankly I think it's pretty stupid to save that kind if information with any kind of app. But I don't want some random person trying to access my personal information because they are bitter they lost their number.  Please let me know as soon as possible so I can change passwords or anything that is needed.
    thanks

    If it were me, I would go to my carrier and get a new number. Since you have only had it for a month, the inconvenience would be minimal.
    Barry

  • Error Occuring While Processing Data With DIAdem 8.1Excepti​on EAccessVio​lation in module ntdll.dll at 000111DE. Access violation at address 7C9111DE in module 'ntdll.dll​". Read address 37363430

    Hello,
    We are having an issue running Diadem 8.1 on a new HP XW 9400 with Windows XP SP2. 3 errors have been occuring with frequent crashes, they are:
    1) "1Exception EAccessViolation in module ntdll.dll at 000111DE. Access violation at address 7C9111DE in module 'ntdll.dll". Read address 37363430.
    2) The instruction at "0x7c9111de" referenced memory at "0x352e302d". The memory could not be "read".
     3) ---Error---   DIAdem
    Error in Autosequence - processing in line: 74 (IARV_VAR_GET)
    Runtime Error while executing command "Iarv2Txt$ := FR(T9,L1)"
    Error type: ACCESS VIOLATION
    Error address: 000101DE
    Module name:ntdll.dll
    We are using the same scripts and version 8.1 on a variety of Dell desktop computers (W2K and XP SP2) without any issue, looking for suggestions as this affects no other software on the HP XW 9400 other than DIAdem. Appreciate any suggestions.
    Message Edited by swillh on 06-25-2007 08:55 AM

    Christian,
    I will answer your questions in the text below. Thanks for your help.
    Hi swillh,
    I also would like to help you.
    Unfortunately, The reported access violation in the central Windows ntdll.dll is very unspecific.
    May be the following questions will help you to provide me more info.
    1. You mentioned that the aut's and - I think - also the accessed text file reside on a server.
    Is there a stable network connection?
    The server can sometimes be a little slow but the connection is good. This computer is using the same connection that the prior computer utilized without issue.
    Are the files accessed by multiple clients simultaneously?
    It is possible that more than one computer can be accessing the same file, but again, this has never been an issue. We are reading the files only, not writing to them.
    The processing routines we are running have used for over 5 years without any issues until adding this computer.
    Is the text file read by one client while another client is writing the same file?
    No, files are "read only"
    2. Have you already tested opening the file with the FileOpen command before calling FR?
    Yes
    Do you see any chance to convert the aut to a vbs file? This gives you more alternatives in accessing text files.
    3. What do you mean with "processing ATD's with 30 or more channels of data"? Where is the relation between ATD files and data channels?
    Processing Crash Dummy data with file sets low in channel count (15 channels) result in successful processing without any crashes or access errors.  When processing dummies with more than 20 channels we sometimes encounter these issues. The higher channel count may be the only common factor I can find in these faults.
    Steve
    Message Edited by swillh on 07-09-2007 08:44 AM

  • Error while executing "" command Error type ACCESS VIOLATION Error Address: 0006898E Module name:gfsdesk.DLL

    Hi All,
    I'm using diadem from .net Program. While on the run I'm getting the following error.
    Error While executing "" Command
    Error type ACCESS VIOLATION
    Error Address: 0006898E
    Module name:gfsdesk.DLL
    Anyone have any idea why this is happening?
    regards,
    Swaroop

    Hi Swaroop,
    It would be helpful to better understand what your code really does. The information that you called DIAdem from your enviroenment is not yet sufficient to understand what the problem might be.
    Andreas

  • Ftp and http access over XDB repository is not allowed...

    When I try to execute the following command on a reasonably fresh Oracle 11 installation:
    insert into "XMLTEST" ( "name", "xmlfof" ) values ( 'small', DBMS_XDB.GETCONTENTXMLTYPE('/public/small.xml') );
    -- The schema is correctly registered, the file "small.xml" is in the /public repository folder, the user has every conceivable role and priviledge
    -- http access works fine from a remote location, tried to execute the command on the server and from remote system...
    I get the following error message:
    ORA-31020: Der Vorgang ist nicht zulässig, Ursache: For security reasons, ftp and http access over XDB repository is not allowed on server side ORA-06512: in "XDB.DBMS_XDB", Zeile 1915
    Searching for an answer on the forum didn't produce any concreate explanation... Does anyone have any idea how to solve this problem?

    As it turns out, the XML file contained a reference to a DTD at an external web-site, which caused the problem - it was identical to that described here:
    Re: ORA-31020 when using XML with external DTD or entities
    After removing the reference, everything works perfectly...

  • What does this error mean? Error: Access violation at address 0053DD46

    I am trying to run diff reports using batch scripts, and its very puzzling that some of the diff report scripts within the batch script are running and some are not, there is no consistency to what is getting errored out.
    I then tried running them manually in foreground on the client and I get the same issue. Has anyone encountered this issue? What do I make of it?,
    4/24/2013 1:29:30 PM - *** MDMConnect starting ***
    4/24/2013 1:29:30 PM - Logged in successfully.
    4/24/2013 1:29:30 PM - Started export job for PLN_FLD_ACCT_DIFF
    4/24/2013 1:29:34 PM - ERemotableException with message: "Server was unable to process request. ---> Error during Export. Export was unable to run. Error: Access violation at address 0053DD46 in module 'mdm_ntier_engine.exe'. Read of address 00000024" while running Export
    4/24/2013 1:29:34 PM - => ERROR: Data Relationship Management Server returned error: "Server was unable to process request. ---> Error during Export. Export was unable to run. Error: Access violation at address 0053DD46 in module 'mdm_ntier_engine.exe'. Read of address 00000024."
    4/24/2013 1:29:34 PM - *** MDMConnect stopping ***
    Thank you
    Tanuja Donavalli

    This is issue is coherent in DRM version 11.1.1.2
    Whenever a property is deleted, the references to that property would still exists/stored in tables. The next version of DRM is made to address this issue, where in it takes care of removing all references whenever we delete the property.
    Cause: Properties was deleted from DRM client but the value was still stored in the compare table for Difference export and causing export to fail.
    Solution: Need to recreate the deleted properties and remove the properties in the exports and delete the properties.
    Going Forward: Instead of deleting the properties we need to remove the property from the export and hide the property.
    Hope this helps.

  • Proxy receiver channel with HTTP destination or URL address?

    Hi Experts,
         I have a scenario as below:
         (Webservice Client)SOAP --> PI --> PROXY(SAP ECC).
         A webservice client calls PI using SOAP. PI then sends the request to SAP ECC using PROXY.
        I am using AAE. Therefore I have ICO.
        In the receiver PROXY channel I have given:
       ADAPTER TYPE: SOAP
       Transport Protocol: HTTP
       Message Protocol: XI3.0.
       Under connection parameters:
       Addressing Type dropdown as 2 entries HTTP destination and URL address.
       In what cases i should use HTTP destination and URL address respectively?
       Which option is preferred?
       Do they work same or differently? How?   
       When I select HTTP destination where should I create the corresponding RFC destination? In PI ABAP stack using SM59 or PI NWA?
       If this HTTP destination is created in PI ABAP stack using SM59 then what type it should be? H? or G? 
    Thanks
    Gopal

    Hi Gopal,
    In creating XI receiver communication channel, you have 2 options for Addressing Type:
    1. URL Address - no need to create RFC destination. You just have to specify the XI receiver host name, HTTP port, path (/sap/xi/engine?type=receiver), Authentication data (logon details for SAP Client number of the PI system).
    2. HTTP Destination - create RFC destination in SXMB_ADM and specify the RFC destination name in your receiver communication channel.
    For SAP documentation, see this link:
    http://help.sap.com/saphelp_nwpi711/helpdata/en/f4/0a1640a991c742e10000000a1550b0/content.htm?frameset=/en/e1/091640a991c742e10000000a1550b0/frameset.htm&current_toc=/en/43/96cbccb9335b77e10000000a11466f/plain.htm&node_id=5
    Regards,
    Naveen.

  • Accessing the global Address List using Java Outlook Connector

    Hi All,
    I have written a code to access the Global Address List using (Jar) in Java outlook Connector
    However i am able to retriev the name and email address of that employee only.
    I want the other details like location(particularly).
    Please help out.
    Thanks,
    Arijit.

    Ari_Dev wrote:
    The scenario is i am an employee and i want to get information regarding other employees(name,location) which are stored in outlook through my java application(using JOC).Just a point of clarification, there is no actual java code in the Sun Outlook Connector. The use of Java with most of our products names is for marketing/branding purposes only.
    Now there are employees who are not stored in my address book or local contacts.For them when i try to read the GAL i can get only their name and email address.So the 'cn:' (name) and 'mail:' (email address) attributes are being provided by the directory for a GAL search.
    however if i try displaying their details using the JOC it comes with proper information through the outlook pop up but cannot read this data.As I said in my previous response, the data that the Sun Outlook Connector provides in the GAL view is determined by the user that the GAL binds to the directory server as, plus the restrictions that user has on the information the directory server will provide for GAL searches/queries.
    This bind user is usually different from the 'super-user' bind user that UWC/Communications Express uses which is why you may see more information in UWC/CE compared to in the GAL in Outlook.
    Therefore you need to work with the Directory Server administrator to increase the information that the Sun Outlook Connector user is able to see.
    Regards,
    Shane.

Maybe you are looking for