RV042 remote admin question

I'm hoping this question has a simple answer that i'm overlooking. One of our customers has to abide with some regulations and a security company has ran a scan on their network and reported vulnerabilities. One of those vulnerabilities is in regards to port 443. When going to their address remotely (i.e. https://dynamicname.dyndns.com), you are prompted for a login even though we specifically defined a port for remote admin (i.e. https://dynamicname.dyndns.com:XXXX). I would think since we defined the port for remote admin then 443 wouldn't be able to access the router. Is there a way to fix this? We tried blocking just port 443 but that locked us out of the router for some reason. Any feedback is greatly appreciated.
Thanks

If port 443 is not used, you could consider forwarding port 443 to a LAN IP that is not used as a workaround to pass the security scan.
Which firmware are you using on RV042?

Similar Messages

2012 - White circle indicator on SQL Agent and Instance even though I am in the sysadmin server role, check remote admin or firewall?

Im in the sysadmin role on the server in question, yet when I connect I see a white circle on both the instance level and SQL Agent nodes. Ive seen this before, but dont recall what I did to fix it on other machines. I believe it has something
to do with the "Remote Admin" firewall setting. Does this sound right?
I can see jobs listed under SQL Agent, but im wondering what features I will not be able to do (from SSMS) unless this is resolved?

Hi shiftbit,
Besides other post, please add your account as local admin on the Server you are connecting to and make sure that you right-click SQL Server Management Studio and choose “Run as administrator” to start it, then check that if you have the green circle on instance
level and agent node.
There is also a blog describing white circle indicator issue for your reference.
Service status watcher in SQL Server Management Studio – How it works
http://blogs.msdn.com/b/psssql/archive/2013/08/22/service-status-watcher-in-sql-server-management-studio-how-it-works.aspx
Thanks,
Lydia Zhang
Lydia Zhang
TechNet Community Support

Remote admin vs LabView

Hello, All!
I am using my LabView 6.1 application on remote PC (Win2k Pro) controlled by
Remote Admin software via LAN.
Main PC with application running is not accesable and only one way to
control the LabView panel is the notebook connected via LAN interface.
It works perfect with one exception: I can not see the context menus when I
right-ckicking on remote screen.
Is it a problem with Remote Admin software or this problem could be
connected to LV itself?
Is it possible to arrange a full-functional remote control panel from LV
environment without second party software like Remote Admin?
Sergey Yakovlev,
[email protected]

Hi, Luca
You're right I can use LV remote panel to control my VI, but actually I need
to change something in diagram via remote connection.
"Luca P." wrote in message
news:[email protected]..
> Hi Sergey
>
> LabVIEW 6.1 introduces remote front panels, that allow users to view
> and control the VI front panels remotely from LabVIEW or from a web
> browser without any programming. Remote panel clients will see "live"
> updates to the VI front panel and can control it. Have a look into the
> LV Help. Search for "remote front panels" in the index tab and look
> into the LV user manual (page 17-10) for more informations.
> This link explains the way to use remote front panel with
> applications:
>
http:/
/digital.ni.com/public.nsf/websearch/3B2160B128EE09A886256B60006FFA66?
OpenDocument
>
> I hope this helps
>
> Luca P.

Can I remote admin Airport Extreme

I've always been interested in seeing if I can remote admin the AEBS and use the opportunity to VPN into one of my machines. I've been able to do it to my Dad's Netgear. How do I do it to my own router?

Yes you certainly can administer the Base Station remotely. Enable it using the Airport Utility -> Manual Setup -> Airport button -> Base Station tab -> check the box to "Allow configuration over ethernet WAN port".
On the remote Mac, run the Airport Utility and from the File menu select "Configure other" then enter the WAN IP address and admin password of the Base Station.
Setting up a VPN link into a computer on your private LAN is a completely separate issue with configuration issues that have nothing to to with the above.

AD Connector Remote Manager Question

all,
trying to install MSFT AD BASE 91170 connector on OIM/OAM 11.1.1.3 environment. Finished the following steps thus far:
1. created OIM/OAM/AD server environments
2. Created OIMGroup and admin user account association
3. Imported the connector
4. Update ADITResource
5. Copied ldapbp.jar and ran uploadjars.sh script
6. Updated search base in Group Lookup Recon and Organization Lookup Recon jobs
7. I was able to provision a user
I have two questions:
1. section 2.2.2.1 (on page 2-14 connector indicates that i need to run installation of remote manager on the AD server). Is this step and the subsequent steps required to be configured. What else do i need to run as part of installation. If the rest of the steps are optional in what cases do they need to be created?
2. My design console Lookup.ADReconciliation.GroupLookup does not have any values, it appears recon did not work in this case. What could i be doing wrong, i can add configuration details if needed. - I have done this before but not sure what i missed this time.
Thanks in advance,
Prasad.
Edited by: Prasad on Oct 25, 2011 11:48 AM

Sagar,
I ran the group lookup recon task several times yesterday. OIM did not populate the lookup. Today i change the recon type from Refresh to Update and changed it back to Refresh and it worked with few exceptions like the one below:
Overall now the records are there, but it is unclear why the original task executions did not pull anything. I did not see any other exception either yesterday.
<Insert failed.><Oct 26, 2011 10:56:27 AM EDT> <Error> <OIMCP.ADCS> <BEA-000000> <Description : Insert failed.>
<Oct 26, 2011 10:56:27 AM EDT> <Error> <OIMCP.ADCS> <BEA-000000> <Thor.API.Exceptions.tcAPIException: Insert failed.
at com.thortech.xl.ejb.beansimpl.tcLookupOperationsBean.addLookupValue(tcLookupOperationsBean.java:1357)
at Thor.API.Operations.tcLookupOperationsIntfEJB.addLookupValuex(Unknown Source)
at sun.reflect.GeneratedMethodAccessor1896.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.bea.core.repackaged.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:310)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.invokeJoinpoint(ReflectiveMethodInvocation.java:182)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:149)
at com.bea.core.repackaged.springframework.aop.support.DelegatingIntroductionInterceptor.doProceed(DelegatingIntroductionInterceptor.java:131)
at com.bea.core.repackaged.springframework.aop.support.DelegatingIntroductionInterceptor.invoke(DelegatingIntroductionInterceptor.java:119)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethod

ARD Admin Question

Hi everyone,
I have a few clients using ARD Client (configured sucessfully).
I have two questions:
1) Can Clients pull up the Chat Window to initiate a Chat Session with the Admin (Me)
2) Should I login to each Client's system using their username/password (aka user account) - or should I create a Universal Administrator UN/PW to access Clients from my ARD Admin console. And if the latter, what's the best way to do this.
Thanks in advance

1)
In System Prefrences, Sharing, Remote Management, Computer Settings, if you check "Show Remote Management Status in menu", then regardless if your observing them or not the user can click on the menu, and see what ARD administrators are online. they can use that menu to request to chat with said ARD admin.
On the ARD computer it pops up as a request to chat in ARD.
I seem to remember some settings in ARD for client initiated chat.
if you uncheck Show Remote managment status in menu bar, and you uncheck show when being observed. Then the client will not show the menu for remote desktop; making it much harder for a user to try and start a ARD chat.
2)
The easy thing to do, is to have one account, witch is deticated to ARD access on every computer. That way you don't have to know every user's name, and paassowrd and you don't loose access every time a user changes their password. I keep the user name the same. For added security you could use a diffrent password for each machine; but then you need to keep track the password.

Unable to connect to DPM Database through Remote Admin Console

Hello all,
I have a fresh install of DPM 2012 server. I am able to locally start the Admin Console and work with the DPM server, however when I attempt this remotely, I get the following error:
Unable to connect to the DPM database on <database instances name> (ID: 33210).
I have verified this is a firewall issue by disabling the firewall and connecting. I would, however, like to create firewall rules for just the ports that are necessary, and have not been able to find the correct ports by following tutorials online.
Any help is appreciated.
I have attempted the tutorial here: http://blog.patricknielsen.net/2011/10/dpm-2010unable-to-connect-to-dpm.html which seemed on the spot, but brings no
joy.
Much appreciated,
J

Hi,
The blog should have worked, but add the program exceptions in windows firewall on the DPM server, again but don't restrict the port usage.
1. %ProgramFiles%\Microsoft System Center 2012\DPM\SQL\MSSQL10_50.<DPM SQL Instance>\MSSQL\Binn\sqlservr.exe
2. %ProgramFiles% (x86)\Microsoft SQL Server\90\Shared\sqlbrowser.exe
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT]
This posting is provided "AS IS" with no warranties, and confers no rights.

Hyper-V Remote Admin on a Domain - Failed to connect to root\cimv2

I'm trying to configure our Hyper-V server so that a user on our domain has administrative control. Our Hyper-V server is on the domain running 2008 R2 (named SERVER85 below), and the client is on Win 7 Ent x64 (named DEV03 below, username accuraty\jkessel).
In the output below you can see that it appears we might have a problem with this user's access to the WMI path root\CIMv2, but if I pull up the advanced security settings for that node in WMI, I see:
Name: Justin Kessel ([email protected])
Apply to: This namespace and subnamespaces
Permissions allowed: "Enable Account" and "Remote Enable" (no others, no denies).
IMHO, the server, the desktop, and user are all fairly "vanilla" with nothing unusual going on. Maybe one thing worth noting: our Small Business Server 2008 (i.e. domain controller) is running as a VPS on SERVER85, so SERVER85 never boots with the
domain controller on. This hasn't ever caused problems except that the machine always thinks it's firewall should be in the "work" configuration instead of the "domain" configuration. I tested running the HVRemote script while the SERVER85 firewall
was turned off, and I get exactly the same results below.
One more note: this user currently can logon through RDP to SERVER85 and administer Hyper-V just fine. This user is *not* a domain admin or an admin on that server - I've simply provided him with the right permissions to be able to RDP and admin Hyper-V
only.
We used HVRemote and it output this info when run on the client:
Microsoft (R) Windows Script Host Version 5.8
Copyright (C) Microsoft Corporation. All rights reserved.
Hyper-V Remote Management Configuration & Checkup Utility
John Howard, Hyper-V Team, Microsoft Corporation.
http://blogs.technet.com/jhoward
Version 0.7 7th August 2009
INFO: Computername is DEV03
INFO: Computer is in domain accuraty.local
INFO: Current user is ACCURATY\JKessel
INFO: Assuming /mode:client as the Hyper-V role is not installed
INFO: Build 7600.16617.amd64fre.win7_gdr.100618-1621
INFO: Detected Windows 7/Windows Server 2008 R2 OS
INFO: Remote Server Administration Tools are installed
INFO: Hyper-V Tools Windows feature is enabled
DACL for COM Security Access Permissions
\Everyone    (S-1-1-0)
     Allow: LocalLaunch RemoteLaunch (7)
NT AUTHORITY\ANONYMOUS LOGON    (S-1-5-7)
     Allow: LocalLaunch (3)
BUILTIN\Distributed COM Users    (S-1-5-32-562)
     Allow: LocalLaunch RemoteLaunch (7)
BUILTIN\Performance Log Users    (S-1-5-32-559)
     Allow: LocalLaunch RemoteLaunch (7)
ANONYMOUS LOGON Machine DCOM Access
ANONYMOUS LOGON does not have remote access
This setting should only be enabled if required as security on this
machine will be lowered. This computer is in a domain. It is not
required if the server(s) being managed are in the same or trusted
domains.
Use hvremote /mode:client /anondcom:enable to turn on
Firewall Settings for Hyper-V Management Clients
Domain Firewall Profile is active
   Enabled: Hyper-V Management Clients - WMI (Async-In)
   Enabled: Hyper-V Management Clients - WMI (TCP-Out)
   Enabled: Hyper-V Management Clients - WMI (TCP-In)
   Enabled: Hyper-V Management Clients - WMI (DCOM-In)
Windows Firewall exception rule(s) for mmc.exe
Domain Firewall Profile is active
   Enabled: Microsoft Management Console (UDP)
   Enabled: Microsoft Management Console (TCP)
Additional configuration may be necessary
This computer is in a domain. If the target server is in a workgroup,
you may need to set credentials for the server for Hyper-V Remote
Management to operate correctly. This step should not be necssary if
the target server is in the same or trusted domain as this computer.
If necessary, from a *NON* elevated command prompt, enter:
     cmdkey /add:ServerComputerName /user:ServerComputerName\UserName /pass
Note that you MUST enter ServerComputerName to BOTH parameters.
You will be prompted for a password after entering the command.
IP Configuration
Windows IP Configuration
   Host Name . . . . . . . . . . . . : DEV03
   Primary Dns Suffix . . . . . . . : accuraty.local
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : accuraty.local
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . : accuraty.local
   Description . . . . . . . . . . . : Intel(R) PRO/100 VE Network Connection
   Physical Address. . . . . . . . . : 00-19-D1-05-57-01
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::4406:b48c:dea3:de50%11(Preferred)
   IPv4 Address. . . . . . . . . . . : 172.16.48.185(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Wednesday, November 10, 2010 3:19:23 AM
   Lease Expires . . . . . . . . . . : Monday, December 20, 2010 9:39:25 AM
   Default Gateway . . . . . . . . . : 172.16.48.1
   DHCP Server . . . . . . . . . . . : 172.16.48.210
   DHCPv6 IAID . . . . . . . . . . . : 234887633
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-62-35-81-00-19-D1-05-57-01
   DNS Servers . . . . . . . . . . . : 172.16.48.210
66.209.192.5
8.8.8.8
                                       66.209.192.15
8.8.4.4
4.2.2.1
   NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.accuraty.local:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Teredo Tunneling Pseudo-Interface:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Stored Credentials
Currently stored credentials:
    Target: WindowsLive:[email protected]
    Type: Generic
    User:
[email protected]
    Local machine persistence
    Target: LegacyGeneric:target=WindowsLive:(token):[email protected];serviceuri=contacts.msn.com
    Type: Generic
    User:
[email protected]
    Local machine persistence
    Target: Domain:target=TERMSRV/server85
    Type: Domain Password
    User: ACCURATY\jkessel
    Local machine persistence
    Target: WindowsLive:target=virtualapp/didlogical
    Type: Generic
    User: 02mybhosqazs
    Local machine persistence
Testing connectivity to server:server85
1: - nslookup for DNS verification.
     Note that failure is OK if you don't have a DNS infrastructure
~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~
Server: sbs01.accuraty.local
Address: 172.16.48.210
Name:    server85.accuraty.local
Address: 172.16.48.201
~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~
2: - ping attempt (ping -4 -n -1 server85)
   Note the ping may timeout - that is OK. However, if you get an
     error that server85 could not be found, you need to fix DNS
     or add an entry to the hosts file. Test 3 will fail and provide more
     guidance.
     This may take a second or two...
~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~
Pinging server85.accuraty.local [172.16.48.201] with 32 bytes of data:
Reply from 172.16.48.201: bytes=32 time<1ms TTL=128
Ping statistics for 172.16.48.201:
    Packets: Sent = 1, Received = 1, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~
3: - Connect to root\cimv2 WMI namespace
***** Failed to connect to root\cimv2
***** Error:     -2147024891 Access is denied.
***** Namespace: root\cimv2
     FAIL - Was unable to connect. Diagnosis steps:
     - Have you run hvremote /add:user or hvremote /add:domain\user
       on server85 to grant access?
     - Are you sure the server name 'server85' is correct?
     - Did you use cmdkey if needed? More information higher up.
     - Did you restart server85 after running hvremote /add for
       the very first time? (Subsequent adds, no restart needed.)
     - Is DNS operating correctly and was server85 found?
       Look at the output of tests 1 and 2 above to verify that the
       IPv4 address matches the output of 'ipconfig /all' when run on
       server85. If you do not have a DNS infrastructure,
       edit \windows\system32\drivers\etc on DEV03
       to add an entry for server85.
INFO: Are running the latest version
3 warning(s) or error(s) were found in the configuration. Review the
detailed output above to determine whether you need to take further action.
Summary is below.
1: Anonymous Logon does not have remote access (may be ok)
2: You *may* need to set credentials for access to the server
3: Cannot connect to root\cimv2 on server85
I'd greatly appreciate some help!
Thanks!

Hi,
It seems that you were using Hyper-V Remote Management Configuration Utility from the link
http://code.msdn.microsoft.com/HVRemote, if so, you can refer to the following link.
Configure Hyper-V Remote Management in seconds
http://blogs.technet.com/jhoward/archive/2008/11/14/configure-hyper-v-remote-management-in-seconds.aspx
By the way, if you want to perform the further research about Hyper-V Remote Management Configuration Utility, it is recommend that you to get further
support in the corresponding community so that you can get the most qualified pool of respondents. Thanks for your understanding.
For your convenience, I have list the related link as followed.
Discussions for Hyper-V Remote Management Configuration Utility
http://code.msdn.microsoft.com/HVRemote/Thread/List.aspx
Best Regards,
Vincent Hu

SCCM 2012 R2 CU3 UPGRADE BROKE REMOTE ADMIN CONSOLE CONNECTIVITY

I installed SCCM 2012 R2 CU3 on my site server but it broke a couple things. I've never had problems with SCCM upgrades before. The admin console works if you log into the site server and run it from there but not when you try it from anywhere else (another
server or a workstation). When you open the admin console on the site server it does have the new version of 5.00.7958.1401. Of the five suggestions that appear when your console won't connect, here's what I know:
1) the remote machines can all ping the site server (call it server 01)
2) we know it's not my account that's a problem as I can open the console on the site server itself
3) This problem happens on server 02, which I put the new admin console on. It also happens with other machines which still have the CU2 console
4) Yes, I'm an admin role, shown by logging into the console on the site server
5) I have another network where everything works. I have not put CU3 on it yet, of course. The WMI permissions on Root, Root\SMS, and Root\SMS\site_ABC are identical on both site servers yet it works on non-upgraded one and not on the upgraded one.
WMI info-I can WMI connect from the site server to these other machines but not WMI connect from the other machines to the site server: not root, SMS, or SMS\site_ABC, nor cimv2, even though the permissions match what is on the working network.
When I launch the console from the site server entries about loading the console loading ok are in SMSAdminUI.log, but when I try to launch the console from other machines no entries are made, even though I changed the SmsAdminSNapIN value to VERBOSE.
I checked DCOM permissions and they are the same on both networks.
Another issue that appeared with this upgrade: I can install the client upgrade to CU3 on other machines but on the site server it fails with "Internal Error 2503" and when you click OK it you get "Internal Error 2502".
Ben JohnsonWY

I'd suspected this WMI problem was only affecting our Server 2012 boxes. I compared RSOPs and noticed the ones having this problem were all under the same OU and getting few GPOs. Our GPO person found a GPO that has somehow become unlinked. He relinked
it. After a gpo update AND a reboot these machines start working again. So CU3 did not cause this WMI after all.
And yes, the CU2 consoles won't connect to a CU3 site server, you have to run the console upgrade.
I fixed the "internal error 2503/2502" by doing this: open task manager, click details, end the explorer task (screen will look blank at first). Click File and select "start new task", enter "explorer.exe' and click the run as admin
button. The msp for CU3 client installed and the screen looks normal again. I only saw this error on the site server and have never seen it before.
Ben JohnsonWY

RV042 VPN Connection Questions

Hello,
I have successfully connected two RV042s to establish a VPN gateway to VPN gateway connection. I have the follow questions, please comment:
1. I would like to keep the VPN tunnel connection time indefinite. Is it sufficient by checking the "Keep-Alive" box on the VPN -> Gateway To Gateway -> Advance page? Or, I have to ping the RV042 periodically?
2. Do the "Phase 1/Phase 2 SA Life Time" (on VPN -> Gateway To Gateway page) settings have any impact on keeping the VPN connection time indefinite? What are the optimal values for them?
3. Is there an API, command, or script to replace a manual clicking on the "CONNECT" button to establish the VPN tunnel from the VPN -> Summary page? Or, is there a way to accomplish this at power up?
4. Is there a way to establish a VPN tunnel without going through login and clicking the "CONNECT" button? (Auto connect at power up?)
Thank you in advance for the comments.
Steve

Hi, Mike,
I did not do any extensive testings on the RV042s, but I did the following things to my RV042s:
1. Enabled the "Keep-Alive" feature (see Administration Guide, page 128),
2. Enabled the "Dead Peer Detection" feature and set the interval to 10 seconds. (see Administration Guide, page 129).
Make sure you save the changes.
These features are available below the "Advanced" button under the VPN selection. I hope this help.
You can power down the router or disconnect the network to verify the result. The VPN tunnel should be re-established and stay connected.
Steve

TV Remote Navigation Question

Hi,
I've made a DVD and everything seems to be working fine except that I can't use the TV's DVD Player's remote to navigate to all of the scenes.
I made a movie and have 12 scenes. Scenes 1-6 show on one "page," and arrows point to the second page which contains scenes 7 through 12. I can click on the arrows with the mouse on the computer, but I can't figure out how to use the remote to alternate back and forth between the page that has scenes 1-6 and the page that has scenes 7-12. I am using the theme called "Center Stage."
Any help appreciated.
Patrick

I think I'd lose my mind long before this project was ever finished if I used the powerbook.
I couldn't agree more. But here's the thing... Unless you know exactly what you are doing within DVDSP, then I'm not one to recommend doing so at a moments notice, nor in terms of a crash course. There is no such thing when it comes to apple's FCS 2.
It takes weeks (if not months) to learn to use FCP, and DVDSP effectively. Nevertheless, if this is the approach you wish to take then post this same question to Apple's Dvdsp forum also so they can confirm the following recommendations.
I'm at a loss to understand why DVDSP3 won't also work on your G5. It should also work on the G4, even though laptops / portables are not my personal choice when working within this particular app.
In terms of additional real estate /work area for DVDSP3, I suggest you use an external widescreen or LCD Monitor .... perhaps the one you have currently connected to your G5 assuming it's a power mac and not an iMac. If it is an iMac and you prefer to use the laptop instead then you'd do well to also have at least one other external fw HD, more SDRam (if it's not currently maxed out), and an external WS /LCD.
To add sub menus look at the Help Menu within iDvd'08 and I quote:
"Creating additional DVD menus
A menu can only hold 12 buttons, so if your DVD requires more than 12 buttons, you can create submenus to hold them.
You can use submenus to organize your DVD into sections. For example, if you want viewers to be able to view scenes, extras, additional movies, or slideshows, you can create submenus to hold buttons that link to them.
To add a submenu:
Click the Add button (shown above) and choose Add Submenu from the pop-up menu.
Click the placeholder text for the new button and type a label for the button.
Double-click the new button to open the new menu.
A Back button that returns to the previous menu is added automatically. You can edit this menu just as you can any other menu."
Lastly, I'd also need to know what kind of graphics card you currently have in the G4 since that too will be a deciding factor in which mac system is a better choice.

Remote pojo question.

I have delegates which are calling remote session beans that return ValueObjects. The remote client then may modify these value objects and return them later to the application via the an appropriate session bean. I would then like to save any changes that have been made.
I expect the Value objects to be POJOs, and not have ties to Toplink. However, when return these VOs, i get a class not found exception:
Caused by: java.lang.ClassNotFoundException: oracle.toplink.indirection.IndirectList (no security manager: RMI class loader disabled)
I don't understand why the client has to know that I am using toplink to handle persistence for these POJOs.
Am I using an incorrect session or something?
Here is my code to get the session:
Project proj = new TLCeleres();
sServer = proj.createServerSession();
sServer.login("pago_temp", "pago_temp");
Session session = sServer.acquireClientSession();
Here is my code to populate the vector of VOs which are returned by the session bean:
ReadAllQuery query= new ReadAllQuery();
               query.setReferenceClass(QueryBarFacilityValue.class);
               query.setSelectionCriteria(new ExpressionBuilder().get("id").equal(queryBarId));
               query.addJoinedAttribute("Facility");
               Vector results= (Vector)getSession().executeQuery(query);
               facilities= new Vector(results.size());
               Iterator iter= results.iterator();
               while (iter.hasNext())
                    facilities.add(((QueryBarFacilityValue)iter.next()).getFacility());
Thanks in advance,
craig

Craig,
The client does not need to know anything about TopLink. The issue is that you have transparent indirection enabled on your collection relationship mapping(s).
Indirection is an excellent performance enhancement on the server side but it is stateful and does not serialize to the client easily.
Check you mappings and ensure that indirection is disabled for the relationship(s) in question.
Doug

Remote Admin Client

We have upgraded from SCCM 2012 sp1 to SCCM 2012 R2. We can open the admin tools on the server with no issues. The problem is with the remote client which will not connect. I have uninstall and reinstall. It connects first time it's opened, but
when I close and re-open it will not connect has anyone had this issues?. We are running windows 8.1 and this issue only happens with the remote client which was install from the CD. I recieve the error below
The Configuration Manager console cannot connect to the Configuration Manager site database. Verify the following:
      •   This computer has network connectivity to the SMS Provider computer.
      •   Your user account has Remote Activation permission on the Configuration Manager site server and the SMS Provider computer.
      •   The Configuration Manager console version is supported by the site server.
      •   You are assigned to at least one role-based administration security role.
      •   You have the following WMI permissions to the Root\SMS and Root\SMS\site_<site code> namespaces: Execute Methods, Provider Write, Enable Account, and Remote Enable
Best regards, Wayne

Hi,
Since the error indicates that it cannot connection to site database, you can test with UDL file:
http://blogs.technet.com/b/michaelgriswold/archive/2014/01/06/the-easy-way-to-test-sql-connectivity.aspx
And please also verify the other items in the message.
AdminUIlog may also help in this case.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Remote Admin applications freeze (sometimes!)

I'd appreciate any help people might be able to offer for this very odd problem I'm having.
Background: I installed Leopard server in my college department yesterday. That went well, and I was able to administer it locally. It served web pages, a wiki; email, webmail all worked well. It's a standard configuration
Then I installed the administration apps on my MacBook Pro so that I could administer remotely. When I launched any of the applications (Server Preferences, Server Admin) they froze -- "application not responding" and I had to force quit the app. Consistently.
So, I packed up and went home for the night. At home, I opened up the MBP and thought I'd give it another try, and lo and behold, NOT A PROBLEM at all! No freezing. I was able to administer the server remotely, add users, etc.
When I got back to the office today, I tried the Server Preferences app, and it froze again! Consistently! Wired or wireless connection on the MBP. Restarted, tried a different (virgin) user account on the MBP. Nothing.
I installed the remote server admin applications on an iMac in the room next to me. No problem at all, it works just fine.
I restarted my MBP, even reinstalled the admin software. Server Preferences consistently hangs.
At the end of the day I once again went home, where I'm posting this, and tried Server Preferences. And... yes, it's working JUST FINE here. I can once again administer the server, add users, not a hint of a freeze. (I guess I should mention that at home I'm on an Airport Base Station connected to a cable modem; at the university I'm either on an Airport BS or the university's ethernet.)
I'm stumped.

Here's a Spinning Beachball faq.
I've found that if Disk Utility can't fix it, you'll need a more robust utility for the repair. I would recommend DiskWarrior. It is the best at directory repairs. It rebuilds then actually replaces your old directory. I feel every Mac owner should have a copy.
Even if it doesn't cure this ailment, you'll likely need it in the future.
Make sure you get the disk so you can boot up on it to run repairs. You can also install it on another drive and run it from there to repair this one. DW works faster that way.
I use DW once a month to try and catch errors in my system from getting too far out of hand. DW has repaired every big and little issue I've had on all three of my Macs.
DALE

Unix admin question - file system is filling up

Oracle 9.2.0.1.0
UNIX AIX 5.2
The oracli3 filesystem was hitting the upper 90%s and I informaed the DBA. Learning from him is just leaning over his shoulder scribbling down as much as I can see while he thrashes through it.
I gleaned some things today that I wanted to check with tthe UNIX pros out there.
As I explained, that particular filesystem was filling up, and so he made some searches, first in the /patches directory. There were not too many there (in size), so he next went to /oracli1/oracle/iAS and did a search for logs like this:
sudo find . -name '*.log' -ls
He found one huge log file, and so had me do the cat /dev/null > command to send it to the black hole.
My question is this - when I next see that we are filling up as it were, should I automatically look for logs? Are they the culprits some of the time? Can offending logs be dealt with in this way (cat /dev/null >) ?
Is there something else I should be looking for ? (The oracli3 is now at 93% so I think we still have things to look at)
Many thanks.
DA
Sorry - one other thing - when I use the
find . -name '*.log' -ls command, how can I change it so that the output is more like that of the "more" suffix? The problem is that I would like to scroll through the output of .log files that this command throws back at me.
Message was edited by:
Dan A

It all depends.
When you assume there's nothing useful in those log files, you hire an Unix admin with zero knowledge of Oracle and have hem wipe those files away, 'because the file system fills up'. In the past we had similar administrators throwing away archived redo log files for exactly the same reason.
YOU on the other hand should set up proper administration procedures to move them away, tar them, and compress the tar file, so they take less space. After another 30 days you throw away the compressed tars.
What you have now is a very unprofessional method to 'administrate' a server.
Actually you are not administrating it all, because when disaster strikes, or disaster stroke in the past, and you need to explain and find out what happened and especially WHY, you will be yelling at the Unix 'admin' because he just has thrown away all log files, 'because the disk was getting full'
As to the second question:
There are a few fundamental concepts in Unix
1 ALL output can be redirected using > < and |, The latter symbol is called the pipe symbol and feeds the output into a filter. The filter is a command which reads the output from a previous command and processes. More, pg, and sort are filters, even sqlplus can be a filter
2 NO special switches should be implemented in any command if you can accomplish it using redirection or filters. So you won't find
TYPE/PAGE (VMS, Dos), but you will find cat <filename> | more
So the answer is you need to add | more to the command line
find . -name '*.log' -ls | more
You would also be advised to try to follow an Unix course, as your question is very fundamental. Alternatively buy the book Classic Shell scripting
Sybrand Bakker
Senior Oracle DBA

RV042 remote admin question

Similar Messages

Maybe you are looking for