RV042 Router

How I Change the setting of the router to allow magicJack to have tone to able to send and receive calls.
Thank you,

Good afternoon,
The RV042 is capable of rules that map multiple public IP addresses in a range to multiple private IP addresses in a range. This should be available once you check the "enable" checkbox on your RV042.
Ensure you have the newest firmware of 1.3.12.19-tm
I will try to locate a RV042 and upload screenshots of what this looks like. I do not see that the documentation specifcally state that one-to-many is available, but that type of option is available under the one-to-one section.
I hope you found this helpful.
Thanks,
-Lindsey

Similar Messages

Online Emulator for RV042 router

Hello:
I am looking for Online Emulator for RV042 router.
If yes, please reply with a link.
If no, please give me a similar one.
Many thanks.

Sang1224 wrote:
Please keep me posted regarding the outcome.
I am never surprised by Verizon's marketing shenanigans, but everyone in my cul-de-sac is running a VZ WiFi router, so the signal is always bogged down. I just want to get this new router and see if it helps with my service.
I will try again today, if I can get someone on the phone.
I'll keep you posted. No contact from either here or {edited for privacy} Verizon Executive Relations Team, who emailed me yesterday. I just checked my call log in DV and my cell, and no missed calls.
In my now daily check of offers, today was 75/75 for $10 and a new router. I clicked it, and unlike your experience, it did offer it to me for only $10 more for 2 years. As tempting as it was to do it for another free router I resisted, waiting to see how this is resolved.
I will wait till later today to see if anyone reaches out before going further.

Restart of RV042 Router

Can anyone answer this for me please? Would I lose my router settings if I were to restart the RV042 router from the System Management>Restart section of the router UI?
The "restart" command is just like a warm reset, correct???
Thanks,
Max

Max,
You are correct. Restarting should not affect the configuration.

Having issues with IP Phones and the RV042 Router

Hello,
We have recently purchased Ring Central IP Phones and are having audio issues. We have a RV042 router with two WAN connections. We called Ring Central Tech support and were told that IP Phones will not work with the RV042 while loading balancing is enabled. Has anyone ever successfully setup IP Phones with a RV042 router while having loading balancing enabled? I configured the port range that the IP Phone use to be bound to WAN 1 but still having problems. Thanks in advance.
Loren

I Have the 5s but my screen keeps freezing up and I have to force restart on my apps!

Issue in Configuring Linksys RV042 router

Hi,
I am facing some issues in configuring the Linksys RV042 router with dual WAN configuration. We are having two internet connection and I want to perform the "Load balancing" between the two internet connections. I have followed the RV042 manual and configured the router.
But while using the Linksys RV042 for load balancing the "Outlook 2007" and "MSN" are frequently disconnecting in the client machines. We could not use the Linksys RV042 router because of this issue.
We are using the "Static IP" for the two internet connection and configured with manual. We are facing issue only in "Outlook" and "MSN" but I can browse the sites without any issues.
Is there any configurtaions needed? Please help us to get the solution in this issue.
If you need any more details please mail me @ [email protected]
Thanks in Advance,
R. Manikandan.

R. Manikandan,
Without knowing more about your configuration, and the reason for "Outlook" and "MSN" disconnecting. I would suggest that you look at the following documentation for setting up "Dual WAN" on the RV042.
http://www.cisco.com/en/US/products/ps9923/products_qanda_item09186a0080a36632.shtml
It sounds like you may need to setup "Protocol Bindings" for your SMTP traffic to be directed out a specific WAN port.
If you continue to have issues, please let us know.
Darren

Unable to connect through QuickVPN to RV042 router

Hi!
I've RV042 router with the firmware 1.3.12.19.
I'm not able to connect from my QuickVPN client ver 1.3.03 to the router.
If anyone know the fix for the above issue kindly let me know.
Thank you,
Regards,
Muthu

Welcome to the forum!
There has been no end to the "Quick VPN not connecting" threads here on the forum, and there can be a number of factors that will cause QVPN to fail. It has gotten to the point where a fellow engineer has created a thread just for Quick VPN issues to try and keep everything contained in one place. It may be prudent to post your question in his thread that you can find at the link below.
QVPN Thread
However, if you would like to continue the discussion here in your own thread I would suggest the first thing you do is post at what point during the connection process does QVPN fail? For troubleshooting purposes go into the directory that you have QVPN installed which for most people will be Program Files>Cisco Small Business> and go into the Quick VPN Client folder. In this folder you will find a log.txt file. If you can post the output from this file (and please edit out your network information) then we might have a better idea why the connection is failing for you.

RV042 Router SMTP port change

Hello, I have an RV042 that I have configured to send alert logs to a comcast email address. Recently comcast changed their SMTP port from 25 to 465. I can't find where to change the port settings in the RV042 to send the router logs via port 465. Any help would be appreciated.
Thanks
Mark

Hi Mark, thanks for using our forum, my name is Johnnatan and I am part of the Small business Support community. You can change the port number using a port-forwarding or a One-to-One NAT in your device, you can also specify the syslog server, I´ll share with you some documentation about it:
http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=544
http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=346
I hope you find this answer useful,
**Please rate useful posts so other users can benefit from it**
Greetings,
Johnnatan Rodriguez Miranda.
Cisco Network Support Engineer.

RV042 router multiple WAN IPS assigned to different LAN IPs range

I would like to have multiple WAN IPS and assigned them to different LAN IPs. If i used the option One-to-One NAT its give me only the LAN IP 192.168.1.xxx . There is an option to specify more than one LAN IPs but its not possible to forward ports to these extra LAN IPS or to setup rules.
Is there anyway to mange this with this router. IF not what is router that will meet my requirements?

Andreas,
Unfortunately what your wanting to do will not work with the rv042. It will only allow the one to one nat rules to be applied to the default lan subnet.
You will have to use the sa500 series router which will let you do ip aliases to different lan subnet addresses.

RV042 - route some IP addresses to WAN2

My Linksys RV042 is in Smart Link Backup mode, WAN1 beeing the primary interface.
I want certain part of my network, IP addresses 192.168.10.128 - 192.168.10.159, to use WAN2 all the time, so that WAN2 is utilized. How to add route to do that? Please help.

Well this is a toughy. Since we cannot define our IP rules with that kind of precession on the RV042 we really can't do that. Now here is a screenshot of something that may work. I say "MAY" as in a real big maybe! The thing is, we can't create a rule that says "send this LAN to this WAN"; otherwise, you probably would not even be asking.
I think if we deny traffic from the WAN to your IPs they should respond back to that particular interface, but there is a small catch. Since our two options on the RV042 is either "Smart Link" or "Load Balance" we are stuck in a little pickle. This is because the client (LAN) is usually the one to initiate the connection and the router will Load Balance and IT will decide which WAN port to go out on. So, my little idea may not work. I am not at work at the momment so I cant take a look at a RV, but I do beleive with the latest firwares we can do protocol bindings and from there we can split traffic.
Anyway, what we need to battle with is "Load Balancing" and we need to place rules that will work in this mode. Let me know if this helps, or maybe someone else will step in with a better idea.

Disable SIP ALG in RV042 router?

Using these routers for VoIP phones, the manufacturer says that SIP ALG must be disabled. I cannot find a setting for this.

RV042 does not suport SIP ALG.

Quickvpn / client to gateway vpn rv042 can only ping router

I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.
I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
Any ideas?

I've narrowed the problem down to option 2 above. If I change the gateway of a LAN resource to point to the LAN side of the router, it can be accessed through the VPN tunnel.
I haven't had time to see if adding routing entries can fix this problem. Any suggestions will be appreciated.
Also, I would appreciate an explanation of why the PPTP connection works. I will research this myself (eventually) but am already backed up with other projects..

Router RV042 problem

My Cisco RV042 router cannot perform their featured functionality in either Smart Link Back up or Load Balance modes.
E.g a) In load Balance Mode WAN 2 will be tunnelingtrafic as primary even though WAN 1 is actually the primary tunnel.
b) In Load balance (auto) Mode, traffic will continue to be tunneled through say WAN 2 port even though the bandwidth on that network has been saturated. Packets will not be spilled over to the other WAN port i.e WAN 1 in this scenario.
Attemts for a solution:
a)Upgraded the Firware to version 4.2.3.03-20140319 on one of the units but this attempt could still not resove the issues. The other units came up with a "connection to device time out" each time I attemped to do a firware upgrade.
b)I reset to factory default but the issues remain the same.
I will be grateful if you can suggest a way foward on this problem.
Robert

Check your bandwidth settings for each wan. If the router thinks you have more bandwidth on a particular wan than you do, it will never move to the other wan.

RV042 giving out router certificate instead of server certificate

Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate.
How do we turn that off or keep it from happenning?
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)
Thank You,
Elias

Hi Angel,
I want to have more details about the issue and the error message when you trying to connect or if you have any log in your server you can share with us because it looks a certificate error
also, I want to have more details about the certificate on the server like :
* common name ,Organisational unit,Company,City, State Country.
Can you ensure the Common name on the server certificate configured with the full domaine name like portal.example.biz not only with example.biz or portal .
and what is the configuration on RV042 regarding the server
Thanks
Mehdi

RV042 - I have customer who upgraded to 20 meg cable internet service and can only get 10 meg thru the router.

RV042 - I have customer who upgraded to 20 meg cable internet service and can only get 10 meg thru the router. The customer had upgrade to a 20 meg cable internet service from a 10 meg service. The customer is only able to get the 20 meg service going from cable modem to PC. If he goes thru the RV042 router, he is only getting up to 10.7 down and 1.37 up. Additional steps taken….He had a Linksys SRW224P switch connected to the RV042 router and we had disconnected this switch for testing purposes. We performed the speed test again and we get the same speed results so we know the switch is not the issue.He had upgraded to firmware version 1.3.12.19 – TM Feb 13, 2009 – tested speed and no change.We accessed the web management interface and tried several modifications. This includes the following…..- We disabled the firewall – no change- We disabled SPI with is the Stateful Packet Inspection (I was thinking this one would do it) – no change in speed.- We disabled DoS (Deny of Service) – no change.- We set MTU to Manual and tested various byte increments based on MTU ping testing. – Once again, no change in speed. He is NOT using Load balancing on the routerHe has NO access rules but does have a few port forwards. Finally, with each change, he is saving the changes on the router.

You are expecting 20MB throughput on a $150 router? Well, ok, maybe.. Can you check on your router or switch if the port is set or auto negotiated to 10 or 100? That could explain 10MB limit (although technically a 10Mb port is considered 20Mb theoretical max throughput as 100Mb port is considered 200Mb per Cisco). So maybe you ended up with 10/half somehow? MTU 1500 would also be good for that connection I think and to try to get max throughput.

RV042 Port forwarding stops working when Firewall is enabled

Hey all,
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows:
HTTP[TCP/80~80]->10.0.0.6
HTTPS[TCP/443~443]->10.0.0.6
IMAP[TCP/143~143]->10.0.0.5
IMAP SSL[TCP/993~993]->10.0.0.5
SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out.
Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Do you know anything I could try?
Best regards,
Theo
EDIT:
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.

Hi Theo, if you want to over ride the default state table, you need to first make firewall rules to block all access then make your permission rules.
Such an example would be-
Action Deny
Service All
Source interface WAN
Source IP any
Destination IP any
Save
Action Permit
Service RDP
Source interface WAN
Source IP -xx.xx.xx.xx
Destination IP - xx.xx.xx.xx
Save
As for your concern about the syn flood, it can be a likely cause of your problems. Does the logging facility of the router give any indications?
-Tom
Please mark answered for helpful posts

RV042 Router

Similar Messages

Maybe you are looking for