RV042 when using both WAN with same DNS servers doesn't work properly

Hi there, I have a RV042 and upgraded it to the latest firmware available. The problem is the following:
when I have on WAN1:
PROVIDER A - MUNDIVOX
IP: 200.201.190.202
SM: 255.255.255.248
GW: 200.201.190.201
DNS1: 200.196.48.20
DNS1: 200.196.48.21
and on WAN2:
PROVIDER B - TRINN
IP: 189.113.129.230
SM: 255.255.255.252
GW: 189.113.129.229
DNS1: 189.113.128.3
DNS2: 189.113.128.2
The load balance works fine and network redirection works fine I can route all trafic from ips 192.168.0.1 to 192.168.0.50 and specific protocols such as UDP on port 5060 for my SIP Phone for ips 192.168.0.101 to 192.168.0.120 works fine.
The problem is when I change WAN1 to:
PROVIDER A - TRINN
IP: 189.113.132.2
SM: 255.255.255.248
GW: 189.113.132.1
DNS1: 189.113.128.3
DNS2: 189.113.128.2
And Wan 2 I keep the same provider that would be the same as Provider for WAN1 now:
PROVIDER B - TRINN
IP: 189.113.129.230
SM: 255.255.255.252
GW: 189.113.129.229
DNS1: 189.113.128.3
DNS2: 189.113.128.2
The load balace simply doesnt work, all the IPs in the range of 192.168.0.1 to 192.168.0.50 that should be using WAN1, uses WAN2, in fact, as far as I could see all my trafic goes with that configuration to WAN2 only, but if I remove the cable from WAN2, all trafic goes to WAN1, so, very strange... if I put back on WAN1 the MUNDIVOX provider from situation 1, everything gets back to the way it should be.
If someone can help I would appreciate,
Regards,
Cristiano

Dear Cristiano,
Thank you for reaching the Small Business Support Community.
It's been several days since you posted your inquiry with still no answer from any of the community members, very interesting situation you have here and unfortunately my only suggestion is to contact the Small Business Support Center to have a TAC engineer check this out;
https://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
I wish I could be a better help and please do not hesitate to reach me back if there is anything I may assist you with in the meantime.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Similar Messages

Search in Outlook 2010 with Exchange Server 2010 doesn't work properly

Hi all,
I have a problem with a clients Exchange 2010. Search function in Outlook 2010 doesn't work properly, the employee can't search mails and contact - he doesn't get any result :-(
In application syslog/protocol I get this error:
Function 'CISearch::EcGetRowsetAndAccessor' found, content indexing for database 'Mailbox Database 0139257080' caused by MSSearch-Error '0x80041820' deactivated
Can anybody help me with this, if its necessary I can give further information :-)
Thomas
Thomas Deinert

Hi,
What’s Exchange Version? Sometimes, after Installing Exchange 2010 SP 1, Searching via OWA or Outlook Online Mode may Fail. If so, please try the following solution:
Download the script
Repair-ExchangeSearchSymlinks.ps1 from the Script Center.
Copy the Repair-ExchangeSearchSymlinks.ps1 script to the Scripts directory on the Mailbox server (default installation is C:\Program Files\Microsoft\Exchange Server\v14\Scripts).
On the afflicted Mailbox server, open the Exchange Management Shell by right-clicking the shortcut and selecting “Run as Administrator”.
Within the Exchange Management Shell, navigate to the Exchange Scripts directory.
Within the Exchange Management Shell, run the following script: .\Repair-ExchangeSearchSymlinks.ps1
Within the Exchange Management Shell, run the following script (without the symbols [] and substitute the database name(s) for any databases you wish to reset: .\ResetSearchIndex.ps1 [-force] <dbname> [<dbname>]...
You will receive an Event ID 109 when the rebuilding of the index starts for each database and an Event ID 110 for each database when the index rebuild has completed.
After receiving Event ID 110 for each database, test to make sure search functions correctly with both OWA and Outlook operating in Online Mode.
Similar thread:
https://social.technet.microsoft.com/Forums/exchange/en-US/35db030c-277f-49d6-83d6-772f839a47f8/owa-2010-sp1-search-problems?forum=exchange2010
Best Regards.

Ipod nano 1st generation with SW1.3.1 doesn´t work properly

as a positive thinking person I followed the recomendations in iTunes 7.5.. and downloaded SW 1.3.1 on my 1st generation nano. The consequnce was that this dammed thing now frequently stops playing(every few minutes max. 15 min). It either jumps back to the main menue and I have to start the song again or it freezes and I have to boot ( middle + menue key) or it reboots by itself.
Have gone through all the 5Rs and the online service, tried to send a message to service, but this was not available and the message was gone. I do not find an older SW version. After hours I am really pi...
Had functional problems during warranty period. Sent it in with new SW it worked properly until last weekend......
Can anyone help. Has anyone made similar experience?

Hello Forum Users et al,
I know this Updated Post follows shortly after my previous post, but I have a useful piece of info. that others may wish to check on.
I have been using a video: www.video.com/12348372 as my test case for which the video comes on and then proceeds to not work. If I click on the "arrow" in the bottom left corner of the video, the video screen goes "black" and nothing happens immediately. But, here is the important information. If I wait, then the video reappears, but sounds alternately starts and stops.
What I did for the last several hours was to minimize the email containing the video, and I noticed that the sound alternately came on and off. But, after over two hours, the video started to play normally (total time for video is about 4 mins.) When it gets to the end, the original "start arrow" appears. I have repeatedly played this video after the two-hour period of erratic play, and it played normally.
This event happened one time over a week ago when I was on "Live Chat" with Adobe FP. I was reporting my problem with FP with Mang Son while I had the video minimized, and, embarrassingly, the video started to work normally! What could I say?! I told him essentially that it looked like it was working, and I closed it out. However, after this, I closed the email containing the video and tried to open the video from scratch, again. Once again, it started to play erratically, even though it mysteriously was playing normally while I was on "Live Chat".
Users may want to use the video that I cited and see what happens. It is still a mystery why the video won't work for hours and then all of a sudden start working. I also had similar trouble with YouTube videos.
Best regards,
bookwilliam

Excel 2013 bug printing when using two printers with same driver

Hi,
Was advise by "Community" to post this one here.
The environment:
Window 7 Sp1 x64
Office 2013 Sp1 32 bit
Windows 2012 Server (current patches).
Two IDENTICAL network connected printers shared from above Windows 2012 server.
As the two printers are the same, they both use the same printer driver.
Printer A is set to Greyscale. This is the default printer.
Printer B is set to Full Colour.
Open Excel and start a blank worksheet.
Choose Print - this shows the default printer (Printer A) - then Printer Properties - this verifies that the Default Printer is set to Greyscale as expected.
Change printer within Excel to Printer B - then printer properties again - this shows us that printing is STILL in Greyscale ignoring the Printer B settings. Printing will indeed produce a greyscale print on Printer B.
The reverse is also true - if we set Printer B (Color) as the Default, then choose Printer A (Greyscale) inside Excel, it will then show (and print) in Full Color - ignoring the printer A setting of greyscale.
This ONLY occurs when connecting to Shared Printers on a Windows host (Server 2012 in this case).
Direct IP printing from Win 7 to the printer works as expected (printer settings honoured).
Non-Windows server based printer sharing works as expected (printer settings honoured).
This ONLY occurs in Excel. Other programs including other Office components do not exhibit this bizarre behaviour.
This ONLY occurs where the same driver is used by both printers.
In effect, Excel is transposing the Default printer's settings onto whatever printer is chosen if it uses the same driver.
Installing Office 2013 Service Pack 1 made no difference.
This appears to be a long running issue (search result show Excel 2007,2010* and Windows 2008R2 server references).
*Confirmed same behaviour with Windows XP and Excel 2010.
This appears to affect multiple brands of printer (Xerox, Konica Minolta). Confirmed with 3 different generation Konica Minolta (Postscript) copiers and Dell multifunction (with PCL drivers).
Does anyone have a solution for this ?
Is there a setting hidden in Excel that should be changed ?
Is there a server setting to "isolate" the two printers from each other ?
Regards
Ian

KR,
Thanks for the reply but note I said "The reverse is also true - if we set Printer B (Color) as the Default, then choose Printer A (Greyscale) inside Excel, it will then show (and print) in Full Color - ignoring the printer A setting of greyscale."
Also, it is the printer properties that are being set. I believe the setting you refer to is per worksheet ?
Cheers
Ian

Scrollbars with painting - why this doesn't work properly ?

Hello I written such a small program:
/* Test.java */
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
public class Test extends JFrame {
     private JPanel mainPanel;
     private InnerPanel innerPanel; // Panel w/ JScrollPane
     private JScrollPane scroll;
     private JButton addItem;
     public static final int WINDOW_WIDTH = 200;
     public static final int WINDOW_HEIGHT = 200;
     public Test () {
          buildPanel();
          add(mainPanel);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          setSize(WINDOW_WIDTH, WINDOW_HEIGHT);
          setVisible(true);
     public void buildPanel() {
          mainPanel = new JPanel(new BorderLayout());
          innerPanel = new InnerPanel();
          scroll = new JScrollPane(innerPanel);
          scroll.setPreferredSize(new Dimension(100, 100));
          addItem = new JButton("Add an item to JPanel");
          addItem.addActionListener(new ButtonListener());
          mainPanel.add(scroll, BorderLayout.CENTER);
          mainPanel.add(addItem, BorderLayout.PAGE_START);
     private class ButtonListener implements ActionListener {
          public void actionPerformed(ActionEvent e) {
               innerPanel.increase();
               innerPanel.revalidate();
               scroll.revalidate();
               scroll.getVerticalScrollBar().setValue(
                    (scroll.getVerticalScrollBar()).getMaximum());
     public static void main(String[] args) {
          Test test = new Test();
class InnerPanel extends JPanel {
     int x0 = 50, y0 = 50, x1 = 100, y1 = 50;
     public void paintComponent(Graphics g) {
          g.drawLine(x0,y0,x1,y1);
     public void increase() {
          x1 += 50;
          setPreferredSize(new Dimension(x1 + 100, y0));
          repaint();
}I click for example 5 times on the button and then move the scroll max to the right.
The end of the line should be already visible, but it's not. However it will be,
when you resize the frame just a bit.
Now when I try to move scroll max to the left but the beginning of the line doesn't show up. However it will , when you resize the frame just a bit.
Can anybody point where I made a mistake ?

Not sure I understand the description of the problem. I didn't notice any change in painting when I resized the frame, but anyway I made the following changes to help with the painting:
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
public class Test6 extends JFrame {
     private JPanel mainPanel;
     private InnerPanel innerPanel; // Panel w/ JScrollPane
     private JScrollPane scroll;
     private JButton addItem;
     public static final int WINDOW_WIDTH = 200;
     public static final int WINDOW_HEIGHT = 200;
     public Test6 () {
          buildPanel();
          getContentPane().add(mainPanel);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          setSize(WINDOW_WIDTH, WINDOW_HEIGHT);
          setVisible(true);
     public void buildPanel() {
          mainPanel = new JPanel(new BorderLayout());
          innerPanel = new InnerPanel();
          scroll = new JScrollPane(innerPanel);
          scroll.setPreferredSize(new Dimension(100, 100));
          addItem = new JButton("Add an item to JPanel");
          addItem.addActionListener(new ButtonListener());
          mainPanel.add(scroll, BorderLayout.CENTER);
          mainPanel.add(addItem, BorderLayout.PAGE_START);
     private class ButtonListener implements ActionListener {
          public void actionPerformed(ActionEvent e) {
               innerPanel.increase();
//               innerPanel.revalidate();
//               scroll.revalidate();
               scroll.getVerticalScrollBar().setValue(
                    (scroll.getVerticalScrollBar()).getMaximum());
     public static void main(String[] args) {
          Test6 test = new Test6();
class InnerPanel extends JPanel {
     int x0 = 50, y0 = 50, x1 = 100, y1 = 50;
     public void paintComponent(Graphics g) {
          super.paintComponent(g); // added
          g.drawLine(x0,y0,x1,y1);
     public void increase() {
          x1 += 50;
          setPreferredSize(new Dimension(x1 + 100, y0));
          revalidate(); // added
//          repaint();
}

Satellite Pro L20 doesn't work properly with USB Fast Track audio i.f.

Hello!
I have used my Fast Track USB on new Toshiba Satellite L40 and I never had problems with it. I could set low latency and I did few songs with it.
Yesterday I bought another notebook, thinking of home recording studio. It's used Toshiba Satellite Pro L20. It doesn't work properly with my interface. When I listen music on Winamp or do anything on Fruity Loops I hear loud clicks, pops, noises. They introduce samples, or they appear during playback or after a sample is stopped.
I noticed, drivers for Satellite Pro L20 are a problem. Its not supported by Toshiba anymore?! The only drivers for chipset are very old and you can download em only from Toshiba website. The chipset is ATI Xpress 200M. Its drivers are with graphic card. Recently I noticed you can download "ATI Catalyst Legacy Display Driver for Windows XP - Motherboard/IGP Drivers 9.11" and CRACK IT to make it possible to install on mobile unit such as L20. Yep its funny but its impossible to do otherwise!
things I have tried and they still not help:
# drivers replacement, original were released in 2004. I installed recent version.
# driver settings, low latency, high latency
# asio and different settings
# pluging the interface to another usb socket.
# trying what happens when I use battery and when I use adapter
# updated bios
# turned off onboard units such as wifi card, sound card
# checked IRQ list
pops still appear.
my config:
Toshiba Satellite Pro L20
Win XP Home SP3
Celeron M 1,5GHz
896Mb ram
M-Audio Fast Track USB, drivers: 6.0.2
Kind regards

Thanks for answer. I still have L40 but I try to run my homerecording on L20. The L40 is now used by whole my family. It's possible to swap them but there's a problem - L20 has Norway keyboard and I'm the only person at home who doesn't often look down while typing. In Poland, we use standard ms keyboard. I'd buy special stickers, it's about only to make special chars get back to their places.
I installed Windows on this computer end set it to best performance possible.
Since I created this thread, guys from M-Audio support tried to solve my problem - nothing helped. I think potential solutions are exhausted.
Message was edited by: lidia.pochron

The cable doesn't work properly when connected as data cable.

Hi,
I have recently encountered problem of the cable. The thing is that if i use it just for charging with the plug, it works fine. But when i wanna use it with computer (i.e., accessing itunes, etc) or with my car, it doesn't work properly, it keeps switching between charging and discharging very fast. I will appreciate your quick support!
Regards,
Farhan

Just for all the people to know, I found out the solution. You have to mark the correct side of the charging cable which connects at inlet of the phone. Because this point acts as a chip when used as data cable or auxiliary use (car,etc). That's why it charges with the plug on any side. I don't know what's the frequency of it happening to iphone 5s users, because I bought it recently (iOS 7.1.1) Hope it helps to others in future.

HT201335 when using apple tv with my ipad, the mirroring function does not work, screen goes black, what is the issue?

when using apple tv with my ipad, the mirroring function does not work, screen goes black, what is the issue? My son's Ipad(same as kind as mine) works ok with the apple tv but mine does not. Any suggestions?

Hello Nina Izurin,
While written for the iPhone, the troubleshooting below can help resolve issues with your iPad's camera, as well.
Camera isn't functioning or has undesired image quality
If the screen shows a closed lens or black image, force quit the Camera app.
If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
Try turning iPhone off and then back on.
Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
Try to remain steady while focusing:
Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
Note: Video-recording features are not available on original iPhone or iPhone 3G.
If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
My issue is still not resolved. What do I do next?
Contact Apple Support.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Cheers,
Allen

Strange behaviour when using connection pooling with proxy authentication

All
I have developed an ASP.NET 1.1 Web application that uses ODP.NET 9.2.0.4 accessing Oracle Database 8i (which is to be upgraded to 10g in the coming months). I have enabled connection pooling and implemented proxy authentication.
I am observing a strange behaviour in the live environment. If two users (User 1 and User 2) are executing SQL statements at the same time (concurrent threads in IIS), the following is occurring:
* User 1 opens a new connection, executes a SELECT statement, and closes this connection. The audit log, which uses the USER function, shows User 1 executed this statement.
* User 2 opens the same connection (before it is released to the connection pool?), excutes an INSERT statement, and closes this connection. The audit log shows User 1, not User 2, executed this statement.
Is this a known issue when using connection pooling with proxy authentication? I appreciate your help.
Regards,
Chris

Hi Chris,
I tried to reproduce your complaint, but was unable to. I didnt use auditting however, just a series of "select user from dual" with proxy authentication. You might want to see if you can put together a small complete testcase for this and open a sr with support.
Cheers
Greg

[svn] 1720: Bugs: LCDS-304 - Authentication not working in all cases when using security constraint with NIO endpoints .

Revision: 1720
Author: [email protected]
Date: 2008-05-14 14:50:06 -0700 (Wed, 14 May 2008)
Log Message:
Bugs: LCDS-304 - Authentication not working in all cases when using security constraint with NIO endpoints.
QA: Yes
Doc: No
Details:
Update to the TomcatLoginCommand to work correctly with NIO endpoints.
Ticket Links:
http://bugs.adobe.com/jira/browse/LCDS-304
Modified Paths:
blazeds/branches/3.0.x/modules/opt/src/tomcat/flex/messaging/security/TomcatLoginCommand. java

Revision: 1720
Author: [email protected]
Date: 2008-05-14 14:50:06 -0700 (Wed, 14 May 2008)
Log Message:
Bugs: LCDS-304 - Authentication not working in all cases when using security constraint with NIO endpoints.
QA: Yes
Doc: No
Details:
Update to the TomcatLoginCommand to work correctly with NIO endpoints.
Ticket Links:
http://bugs.adobe.com/jira/browse/LCDS-304
Modified Paths:
blazeds/branches/3.0.x/modules/opt/src/tomcat/flex/messaging/security/TomcatLoginCommand. java

Scope when using a JavaBean with JSP

what is the meaning of this question .....?
"Which of the following can not be used as the scope when using a JavaBean with JSP? "
question 4
site :http://java.sun.com/developer/Quizzes/jsptut/

The question is clearly written. I don't see how you can be confused. But let's assume you are since you would not have posed the question.
Dumbed-down:
There are 4 scopes or areas of variable visibility in JavaServer Pages. Which of those can areas can not be used with JavaBeans?
Does that help?

When using Camera raw with PS12 after editing, I cannot save my file in JPEG, only DNG

When using Camera RAW after editing photo I can only save file as DNG, I want to save as JPEG. HOW??
THANKS LLOYD

BARBARA,Yes, you are so right, I was deceived by the eve button, Just tried it and it WORKS GREAT-Thanks for the help.
THANKS AGAIN AND HAVE A GOOD DAY Lloyd
From: Barbara B. <[email protected]>
To: Lloyd Bennett <[email protected]>
Sent: Tuesday, January 13, 2015 11:46 AM
Subject: When using Camera raw with PS12 after editing, I cannot save my file in JPEG, only DNG
When using Camera raw with PS12 after editing, I cannot save my file in JPEG, only DNG
created by Barbara B. in Photoshop Elements - View the full discussionYou are being deceived by the Save button, like most people. That button is not the Save As button, really, but a link to the DNG converter. To save your raw file in an image format, click the Open button instead and then save in the format of your choice in the editor. If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7092207#7092207 and clicking ‘Correct’ below the answer Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7092207#7092207 To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following" Start a new discussion in Photoshop Elements by email or at Adobe Community For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

How to avoid data repetation when using select statements with innerjoin

how to avoid data repetation when using select statements with innerjoin.
thanks in advance,
satheesh

you can use a query like this...
SELECT DISTINCT
         frg~prc_group1                  "Product Group 1
         frg~prc_group2                  "Product Group 2
         frg~prc_group3                  "Product Group 3
         frg~prc_group4                  "Product Group 4
         frg~prc_group5                  "Product Group 5
         prc~product_id                  "Product ID
         txt~short_text                  "Product Description
UP TO 10 ROWS
INTO TABLE l_i_data
FROM
Joining CRMM_PR_SALESG and
COMM_PR_FRG_ROD
crmm_pr_salesg AS frg
INNER JOIN comm_pr_frg_rod AS prd
ON frgfrg_guid = prdfragment_guid
Joining COMM_PRODUCT and
COMM_PR_FRG_ROD
INNER JOIN comm_product AS prc
ON prdproduct_guid = prcproduct_guid
Joining COMM_PRSHTEXT and
COMM_PR_FRG_ROD
INNER JOIN comm_prshtext AS txt
ON prdproduct_guid = txtproduct_guid
WHERE frg~prc_group1 IN r_zprc_group1
   AND frg~prc_group2 IN r_zprc_group2
   AND frg~prc_group3 IN r_zprc_group3
   AND frg~prc_group4 IN r_zprc_group4
   AND frg~prc_group5 IN r_zprc_group5.
reward it it helps
Edited by: Apan Kumar Motilal on Jun 24, 2008 1:57 PM

How do you stop needing to verify email password when using yahoo.att with Mac Mail

How do you stop needing to verify email password when using yahoo.att with Mac Mail?

Nevermind, I fixed it (I think). I went into Settings | Accounts & Sync and found Yahoo at the bottom of the list (alphabetically). I selected it and it had an optiion to delete the account, which I did.

WHY THE IPHONE GETTING HOT WHEN USING 3G PLUS WITH DATa?, WHY THE IPHONE GETTING HOT WHEN USING 3G PLUS WITH DATA?

why my iphone 4s getting hot when using 3g plus with data?
then my phone left side speaker didnt work when i list songs?

It is normal for the phone to get hot when your using data such as YouTube videos, streaming music etc.. And as for the left speaker not working, the left speaker is a microphone, the right one is for sound. Don't worry, everything your iPhone is doing is normal.

RV042 when using both WAN with same DNS servers doesn't work properly

Similar Messages

Maybe you are looking for