RV082 loses all vpn connections over night

I have a RV082 vpn router with 20 VPN connections permasnently deployed.  I am using 1.3.98 tm firmware (latest)  After long periods of inactivity (overnight)
the VPN cease to function  there is no indication of a problem. The tunnels are showing active in the VPN summary screen.  If I restart the router from the management  page the tunnels are restored.

OK.   Next, lets check the other side of the tunnel.  Which product is that?  Are Keep alives and DPD enabled there?
Also, lets look in the LOG file of the RV082 and see what it says.   Should show the tunnel trying to reconnect after it failed and may give us hints.
Here is an RV082 bringing up a tunnel (as an example for reference).
Jun 4 05:26:17 2009    VPN Log   initiating Quick Mode PSK+ENCRYPT+TUNNEL+PFS to replace #5453 Jun 4 05:26:17 2009    VPN Log   [Tunnel Negotiation Info] >>> Initiator send Quick Mode 1st packetJun 4 05:26:17 2009    VPN Log   [Tunnel Negotiation Info] <<< Initiator Received Quick Mode 2nd packetJun 4 05:26:17 2009    VPN Log   [Tunnel Negotiation Info] Inbound SPI value = ddfeccbJun 4 05:26:17 2009    VPN Log   [Tunnel Negotiation Info] Outbound SPI value = d866cd5bJun 4 05:26:17 2009    VPN Log   [Tunnel Negotiation Info] >>> Initiator Send Quick Mode 3rd packetJun 4 05:26:17 2009    VPN Log   [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJun 4 05:26:17 2009    VPN Log   Dead Peer Detection Start, DPD delay timer=10 sec timeout=10 secJun 4 05:26:17 2009    VPN Log   ignoring Delete SA payload: IPSEC SA not found (maybe expired)

Similar Messages

  • HT1339 My iPod classic shows that memory full in "other" category however there is nothing on it. I have left it connected all day and over night trying to restore it but the progress bar  never goes away.

    My iPod classic shows that memory full in other category however there is nothing on it. I have left it connected all day and over night trying to restore it but the progress bar  never goes away. Is it shot or are there other options to restore to factory settings?

    Hi pbworth,
    When troubleshooting issues with iPod classic, it may be helpful to place the iPod into Disk Mode. For information on how to do so:
    Putting iPod into Disk Mode
    http://support.apple.com/kb/HT1363
    Thanks,
    Matt M.

  • Nokia C7 - Problem with VPN Connection over WLAN

    Hello,
    today I installed Nokia VPN Client 44.01(5) for Belle.
    Before this update I used the following configuration: I set two SIP-profiles up and for each profile a own VPN-connection. One for connecting over radio and one for connecting over WLAN or hotspots.
    So over all I had three kinds of connections or connection groups to choose: "Internet" with the radio and home wlan connections, "Intranet" for the VPN-connection over radio and "Intranet over WLAN" for VPN-connections over other WLANs.
    The advantage of this configuration was that I could use the SIP-profile depending on my location and the phone had not to use the "standard" VPN-connection ("Intranet") over radio.
    Now after the update I have the problem that I can't connect to my VPN over WLAN at all. Not with the SIP profile and not manually over the internet browser. There is always the notification "Connection Problem".
    I tried also to put the "VPN over WLAN access point" from the "Intranet over WLAN"-group to the "Intranet"-group and gave it the first priority, but that doesn't helped too.
    Does someone of you had or have the same kind of problem or otherwise has any clue about that?
    Any help is very much appreciated!
    Thank you in advance! I hope that I described my problem clearly.
    Greetings
    unsys

    testing with the faceplate removed and into the master socket witha brand new filters result's below . I tried the quiet line test and it seems silent so no issues there. Can anyone see an issue, I've posted the noise results etc as well with the faceplate removed. (using a butter knife cause i'm just out of bed and tools are in the garage!)
    0.7 Mbps
    0 Mbps
    1 Mbps Max Achievable Speed
    Download speedachieved during the test was - 0.7 Mbps For your connection, the acceptable range of speeds is 0.2 Mbps-1 Mbps. Additional Information: Your DSL Connection Rate :1.06 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM) IP Profile for your line is - 0.75 Mbps
    System Up Time 00:11:28
    Port
    Status
    TxPkts
    RxPkts
    Collisions
    Tx B/s
    Rx B/s
    Up Time
    WAN
    PPPoA
    6657
    9689
    0
    2806
    19425
    00:10:58
    LAN
    10M/100M
    28652
    22350
    0
    22356
    5418
    00:11:24
    WLAN
    11M/54M/300M
    0
    0
    0
    0
    0
    00:11:11
    ADSL Link
    Downstream
    Upstream
    Connection Speed
    1056 kbps
    448 kbps
    Line Attenuation
    49.0 db
    27.0 db
    Noise Margin
    10.6 db
    20.0 db

  • Mac Mini *half* loses all network connections

    Cheers folks, new one on me.  I have a Mac Mini 2.26Ghz Core 2 Duo. It's running a fully-updated 10.6.8.  It's connected via ethernet to an Airport Extreme which is extending an 802.11N network from another Airport Extreme elsewhere which is connected to the router.  The network is set with IPv6 *off* and is configured to run over Ethernet normally (this is because a wired-only NAS is connected to the same Airport Extreme as the Mini).
    Here's the symptom, and it's an odd one for me:   Every couple of days, the entirety of the Mac OS X layer (not the BSD layer) will lose network connectivity.  More specifically:
    No web browser will work ('Not connected to the Internet').
    Home Sharing, served on this Mini, will cease to be visible from elsewhere in the house (AppleTVs lose it).
    No internal services can be reached by name, either DNS or BonJour.
    The App Store says 'can't connect.'
    iTunes will say it can't connect to the ITMS.
    This is true on Ethernet *or* on Airport (the Mini usually runs on ethernet alone with AirPort off; bringing up Airport once this has occurred doesn't seem to help anything).
    Running the Airport Utility, it sees *no devices* (there are 4 on this network)
    BUT!
    If I go into the Terminal, I can not only get clear network traffic anywhere I want at the TCP layer, DNS seems to work as well.  So the following is true also:
    'ping cisco.com' (or any valid DNS name) works fine - resolves DNS, pings.
    'traceroute cisco.com' works fine - resolves DNS, traceroutes out across the internet, no problems.
    'ping <IP address of NAS>' - works fine.
    'dig <name>' - works fine.
    pinging the gateway (the router airport) works fine.
    Also:
    Other Macs in the house (on wired OR wireless, connected to any of the AirPorts including the same one as the Mini) work fine.
    Other Macs can see the NAS connected to that same AirPort fine.
    iOS devices in the house connected to any AirPort work fine.
    netstat -r shows what look to be proper routes - i.e. the default gateway is the router address (10.0.1.1) and the route to 10.0.1.1 is shown to be the MAC address of the router's Ethernet interface (anyway, as I mentioned above, network stuff from the shell works fine<!?!??!
    Steps tried:
    Turning off ipv6 - nope.
    Applying all firmware/software updates (OS X 10.6.8) - nope.
    Tried manually setting DNS to Google public DNS servers - nope.  Those work fine, and are still set when the network drops out, and then don't work, nor does setting new DNS servers in the Network prefpane.
    Logging out/back in - nope.
    Restarting the computer:  YES.  This works, all three times this has happened (all this week).  Serious PITA.
    I tried going through the system log, but I don't see anything notable that changes or is logged when the network connection drops.
    Every time the connection has stopped working, the computer *has* slept at some point since it was last known working, but if I sleep the computer manually, everything seems fine.
    .....waaaaaaaah!  Help, this one is making me crazy. :-)  Thanks.  I'm terminal-savvy, and fairly OS X savvy.

    I still have this issue.  About every one hour - two days the DNS layer will stop working and only a restart will fix it.
    Killing mDNSResponder only resolves the issue sometimes and even then for a few seconds.
    I have now found and created the following bash script, to see if this will be a more reliable non-restart fix that killing mDNSResponder in the terminal:
    #!/bin/bash
    #Script to unload and reload mDNS as it is a bit crappy
    sudo launchctl unload /System/Library/LaunchDaemons/com.apple.mDNSResponder.plist
    echo "mDNS unloaded"
    sleep 5
    sudo launchctl load /System/Library/LaunchDaemons/com.apple.mDNSResponder.plist
    echo "mDNS loaded"
    sleep 5
    echo "Hopefully you can get on with browsing again"
    I saved the above as mdns_reload.command, and then in Terminal ran "chmod u+x mdns_reload.command".  This makes the script executable.
    The next time the problem occurs I am going to test how good this script is as a resolution.
    The second time the problem occurs I am going to try the following, from a different thread from 2011:
    I don't know if anyone will be helped by this, but the Macbook problems connecting to the internet are directly related to DNS issues. I discovered this after an upgrade to the OS X Lion preview.
    The symptoms are as follows: a macbook (pro, mini, etc) can get an IP address from a DHCP server on any given network, but can not connect to the internet, even though other computers on the same network have no issues. If this sounds familiar, read on.
    The problem is not related to 3rd party products, routers, Airport settings, locations or public vs private DNS servers, and you don't need to reset SMC or PRAM.
    You will need to use terminal and you DO NOT want to use disk utility to repair permissions.
    The most direct way to fix this is to copy the com.apple.mDNSResponder.plist and com.apple.mDNSResponderHelper.plist files from an internet connected Mac into your /System/Library/LaunchDaemons directory.
    (You should know that it probably doesn't matter what version of OS X you have or the other Mac has, you just need the files.)
    Next you will need to change ownership of the files just copied (ex: chown root:wheel /System/Library/LaunchDaemons/com.apple.mDNSResponder.plist and chown root:wheel /System/Library/LaunchDaemons/com.apple.mDNSResponderHelper.plist)
    Then, you will need to set correct permissions (ex: chmod -R 755 /System/Library/LaunchDaemons/com.apple.mDNSResponder.plist and chmod -R 755 /System/Library/LaunchDaemons/com.apple.mDNSResponder.plist)
    The last thing you'll want to do is to verify that the ownership of the files copied is set to system (and maybe wheel) using "Get Info." (Conversely, you can use ls -l /System/Library/LaunchDaemons/com.apple.mDNSResponder.plist to verify owner and permissions.)
    You should not have to restart to connect immediately to the internet.

  • How to show IP's of all users connected over AFP?

    Hello --
    In my office, we all use Mac OS X filesharing to share projects, files, etc. I'd like to be able to see what IP addresses are connected to my computer as AFP clients. ...Using "who" in Terminal won't work since everyone connects to me using the same account name. Is there another way to do this?
    Thanks in advance!
    Mike

    netstat -an | egrep 548
    Roger

  • Why did I lose all internet connectivity with new Mozilla Firefox update?

    I recently updated mozilla firefox on my other computer, an ibm thinkpad (windows xp) and since installing, there is no longer any ability to connect to the internet, even with internet explorer. I even tried to do a system restore and this did not work. What can i do to fix this?

    When you can not connect after an update, it is usually caused by a firewall blocking the new version of Firefox. Try removing Firefox from the rules list of your Firewall which will force the firewall to create a new rule for Firefox. Also see [[Firefox cannot load websites but other programs can]].

  • Lion Recovery (Command R- reinstall Lion) Says 148 hours after being on for one day and over night

    I accidently deleted some file on my computer that wouldn't let me start up my MacBook pro, 13 Inch, so I had to press Command- R at start up (brought me to Lion Recovery) and I choose reinstall lion and I started it yesterday morning and all day and over night. It's barely half way through and it says "148 Hours Left" which is crazy.. Should I just wait? is this normal? what do I do? Pleasee help someone!

    It seems Apple is having problems with there servers or you have a Very Slow Internet connection. Best is to let it run as you can't use the computer anyway without the files you deleted.
    There are reports of other that can not even get to the Lion download or any downloads for updates and such.

  • Cannot sustain VPN connection

    I need to work from home 2-3 days a week and moved to Infinity just before Xmas - now I can't sustain a VPN connection, over either wireless or wired ethernet connection.
    The connection is made fine, first time, but drops after usually a minute or 2, and after that will not reconnect without a PC reboot (and sometimes not even then.)  From the VPN client (Cisco) error messages the client is unable to resolve any of the four VPN gateways that are available.
    If I use a mobile dongle to connect the PC to the internet, the VPN stays up - but is too slow to be workable (and expensive) -  but that to me rules out any client/PC issues.
    I've been through this forum quite extensively and this looks like the problem with "BT Web Address Help" that many others have had - but I can confirm that I have opted-out of this service at least a week ago now, and there's no change in the way VPN behaves.
    Please can someone assist on this as I'm unable to do my job without home VPN access - this is making me do an extra two 80 mile round trips each week to connect to the corporate network.

    Changing the PC's MTU value might help, or even changing your DSL Router?
    http://community.bt.com/t5/BB-in-Home/BT-Home-Hub-2-0-crashes-using-Ethernet/m-p/10660#M6062
    http://community.bt.com/t5/BB-in-Home/BT-Broadband-and-MTU/m-p/12660
    The Homehub2 often doesn't like transferring large files especially if fragmented, which is more likely when using VPN.
    "I have this awful feeling someone is watching every move I make (one of my pet hates is router location tagging)." Marvin (A paranoid Android)

  • Can I enable "Use default gateway on remote network" on VPN connection using Group Policy?

    Hi,
    First timer here so please bear with me!
    Environment: Domain Windows 2003, Clients: Windows 7 and Windows XP (with Client Side Extensions pushed out)
    When creating a VPN connection on a client machine manually with default settings the "Use default gateway on remote network" found in [Connection Properties - Networking - IPv4 - Advanced] is enabled, which is good as we don't allow split-tunneling.
    I have a test GPO that creates a new VPN Connection [Computer Config - Preferences - Control Panel - Network Options], but the above setting is unticked.
    Am I missing something on the options for the GP preference to set this automtically?
    I can write a script to directly change the C:\Users\All Users\Microsoft\Network\Connections\Pbk\rasphone.pbk file but would prefer if I could sort it all out using Group Policy.
    Any help would be greatly appreciated!
    Thanks a lot!
    David

    Shane,
    There is actually a way to set the "Use default gateway on remote network" through Group Policy Preferences. And this may even be a better way to do it, because you may change this flag without touching any other settings, or other VPN connections.
    (All VPN connections are stored in the same .pbk file.)
    Here's the trick: Opening the .pbk file in notepad, I realized that this is actually an oldstyle ini-structured file. And Group Policy Preferences can update ini files! In the .pbk file the section names are the VPN connections names, like [My VPN],
    and the property IpPrioritizeRemote is the flag "Use default gateway on remote network".
    So, in Group Policy Management Editor, go to Preferences / Windows Settings / Ini Files.
    Create a new object with Action = Update, and File Path =
    C:\ProgramData\Microsoft\Network\Connections\pbk\rasphone.pbk
    (If this is where your file is located, I guess it is in c:\users if the VPN connection is made for a single user.)
    Section Name should be the display name of your VPN connection, without the brackets.
    Property Name = IpPrioritizeRemote
    Property Value = 1
    Peter, www.skov.com, Denmark
    Peter :-)
    This is great, but just one question. I also want to append a list of DNS Sufixes in order (when viewing a VPN properties, this is buried in
    "Networking --> IPv4/6 --> Advanced --> DNS --> Append these DNS Suffixes (in order)". However, for the VPNs I have manually created with this list populated, I can't see any entries in the rasphone.pbk. Does anyone know
    where these are stored?
    Cheers.

  • Dual Simultaneous Site to Site VPN connections

    My goal is to have an 891 router at a branch office with two, always active VPN tunnels where the routing would switch to the secondary tunnel within the 891. On the Hub side there would be two ISPs connected into the same MPLS cloud which has internet access. Is this possible? Which device should I terminate the VPNs on. Typically used ASAs in the past.
                    Remote Site
                           I
                         891
                           I
                     Cable/DSL
                           I
                       MPLS
                           I
                    ISP1 ISP2
                       I        I
                     R1     R2
                       I        |
                    ASA  ASA
                       I        I
            Core SW1  SW2 Core
                        Server
    To take it even further I would like to configure the branch office with two ISPs but have a VPN connection over both.

    HI ,
    As far I know, you cant create two IPSec VPN tunnel from same source to same destination in single router. For this you may can consider DMVPN but ASA doesnt support this yet. You would typically need a ISR router to do this.

  • How can i use an existing vpn connection without using the option "Send all traffic over vpn connection"?

    I have been trying to get my computer (os x.7) to astablish a remote desktop connection to my work computer via a vpn tunnel. In fact I have just discovered that it works fine if i select to "send all traffic over vpn connection" from the options in the advanced setup of the vpn.
    If the option is selected microsofts "Remote desktop connection for mac" works just fine. However without selecting the option it is not taking advantage of the tunnel but tries to connect as if the tunnel would not exist.
    Now the question is how do I get program to use the vpn tunnel without checking the above option?
    Thanks for any hints and pointers.

    Then can her computer be authorized to both accounts?
    Absolutely. You can authorize any given computer to up to five iTunes Store accounts.
    If purchases are made on her account, to a computer authorized to my account, can I put those songs on my iPod?
    If you connect your iPod to her computer, yes. Tracks download only to the computer from which they're purchased, regardless of which iTunes Store account is used for the purchase. Or you could copy the tracks from her computer to yours and then authorize your computer to her iTunes Store account. But that's sort of defeating the original purpose, it would seem to me.
    is it better to buy music through Amazon downloads and/or actually purchasing CDs to avoid the security features iTunes puts on its music?
    That's certainly an option. If it's an entire album I want, I buy CDs. That way I can import them at the quality I want and to whichever of my systems I want. Amazon or one of the other download stores that offer tracks as MP3 are also an option, though for me download stores are best when you just want a couple of tracks off a given CD.

  • HT1386 When I connect my iPod to my computer and try to sync Apps from my computer to the iPod, a warning comes up saying that I will lose all my existing Apps. Please help

    I have got a new computer and i can no longer do a full sync. Apple always tells me I will lose all my exisiting Apps if I do a new sync. I prefer to purchase Apps on my computer over my iPod because of the smaller iPod. The new computer is recognized by Apple as an allowable new PC.
    But this Sync warning is a pain. Plus, when i view my iPod's App icons on my copmputer, I can no longer drag and move them. I have the latest version of iTunes installed. Thank you for your help

    Syncing to a new iTunes library or computer will erase your iPod. Only if you back up your device manually before syncing, you can restore it from that backup again. A manual backup does not include the sync process.
    Do this:
    Disable autosync in iTunes, connect your iPod to your new computer and right click on it in the device list and choose backup. iTunes will backup your iPod without syncing.
    Transfer your purchases the same way, choosing "transfer purchases" this time.
    When you connect your iPod for the first time, all media content will be erased. But you can restore your settings and app data from your manual backup afterwards.
    Don't forget to set up at least one contact and event on your new computer to be able to merge calendars and contacts when you sync the iPod for the first time.
    Music is one way only, from the computer to your device, unless you bought the songs in itunes and transferred your purchases.
    There is 3rd party software out there, but not supported by Apple, see this thread:http://discussions.apple.com/thread.jspa?threadID=2013615&tstart=0
    About backups and what's saved: iTunes: About iOS backups
    How to back up and restore:http://support.apple.com/kb/HT1414
    How to download apps for free again:http://support.apple.com/kb/HT2519
    Saving other data is also described here. How to back up your data and set up as a new device
    As for your second problem, see if restrictions for app installation and deleting apps are active in Settings/General/Restrictions. If yes, allow to install and delete app again.
    Don't forget to authorize your PC in iTunes:
    About iTunes Store authorization and deauthorization
    Message was edited by: Ingo2711

  • Please help me to find my iPad and iPhone 5C. I lost all of them last night. I set up icloud for my devices but i can't find them because they were not connect to the Internet. Please guide me other ways to find my "best friends".

    Dear Apple,
    Please help me to find my iPad Air 2 64 GB and iPhone 5C 8GB. They're in IOS 8.0 maybe...I lost all of them last night. I set up icloud for my devices but i can't find them because they were not connect to the Internet. Please guide me other ways to find my "best friends". They're very important to me. Many important files for my job in here and it has sentimental value to me. My boyfriend gave it for me so i don't want to lose them. And because i just lost my iPad Air last 3 month, and now i just bought iPad Air 2 two months ago. I'm so sad and lost. I want to catch the thief to the police so bad because they keep my bag and many other important things. I can not do anything without them. Please help me and contact me via my email or my phone. Thank you very much. Hope to receive your answer soon.

    Hey there thaovy309,
    Welcome to Apple Support Communities.
    The linked article below provides a lot of great information and suggestions that should address your concerns about your data and finding your lost or stolen iPhone 5c and iPad Air 2.
    If your iPhone, iPad, or iPod touch is lost or stolen - Apple Support
    Take care,
    -Jason

  • Unable to access local resources or RDP over VPN Connection

    Dear Tech People.
    I have a Windows 7 computer that I have created a VPN service through Windows on.  I am able to connect to the VPN from outside of my network with my Macbook Air.  However, I am unable to connect to the computer via RDP, nor can I ping my PC that
    I am VPN'd into (192.168.1.252).  When I am connected, the IP address that I am assigned, is 192.168.1.150.  When I run ipconfig /all, I can see the "RAS < Dial In> Interface for VPN, and it is setup with an ip address of 192.168.1.151
    with a /32 subnet mask.  There is no default gateway listed, which is why I believe that this is not working.  I cannot determine any way to make this change.
    Basically, I have a VPN connection that I can do nothing with.  I cannot access shared resources, nor can I start a remote desktop session.  The pass through is setup for PPTP with my router, which I believe is working, as I couldn't even connect
    prior to this.  Below is the full results of my ipconfig /all command on my Windows PC:
    C:\Users\Zach>ipconfig /all
    Windows IP Configuration
       Host Name . . . . . . . . . . . . : Serenity
       Primary Dns Suffix  . . . . . . . :
       Node Type . . . . . . . . . . . . : Hybrid
       IP Routing Enabled. . . . . . . . : Yes
       WINS Proxy Enabled. . . . . . . . : No
       DNS Suffix Search List. . . . . . : att.net
    PPP adapter RAS (Dial In) Interface:
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : RAS (Dial In) Interface
       Physical Address. . . . . . . . . :
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
       IPv4 Address. . . . . . . . . . . : 192.168.1.151(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.255.255
       Default Gateway . . . . . . . . . :
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Ethernet adapter Local Area Connection:
       Connection-specific DNS Suffix  . : att.net
       Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet
       Physical Address. . . . . . . . . : BC-5F-F4-85-5E-A8
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
       IPv6 Address. . . . . . . . . . . : 2602:306:ce94:2570:3144:306c:cdae:d615(Pr
    eferred)
       Temporary IPv6 Address. . . . . . : 2602:306:ce94:2570:bd83:220:80a0:eb1e(Pre
    ferred)
       Link-local IPv6 Address . . . . . : fe80::3144:306c:cdae:d615%11(Preferred)
       IPv4 Address. . . . . . . . . . . : 192.168.1.252(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Lease Obtained. . . . . . . . . . : Saturday, October 26, 2013 7:27:27 PM
       Lease Expires . . . . . . . . . . : Thursday, October 31, 2013 7:28:28 AM
       Default Gateway . . . . . . . . . : fe80::22e5:64ff:fe0c:5640%11
                                           192.168.1.254
       DHCP Server . . . . . . . . . . . : 192.168.1.254
       DHCPv6 IAID . . . . . . . . . . . : 247226356
       DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-2E-8E-B2-BC-5F-F4-85-5E-A8
       DNS Servers . . . . . . . . . . . : 192.168.1.254
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Ethernet adapter VMware Network Adapter VMnet1:
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet
    1
       Physical Address. . . . . . . . . : 00-50-56-C0-00-01
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
       Link-local IPv6 Address . . . . . : fe80::d906:32d3:7108:1227%15(Preferred)
       Autoconfiguration IPv4 Address. . : 169.254.18.39(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.0.0
       Default Gateway . . . . . . . . . :
       DHCPv6 IAID . . . . . . . . . . . : 335564886
       DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-2E-8E-B2-BC-5F-F4-85-5E-A8
       DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
                                           fec0:0:0:ffff::2%1
                                           fec0:0:0:ffff::3%1
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Ethernet adapter VMware Network Adapter VMnet8:
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet
    8
       Physical Address. . . . . . . . . : 00-50-56-C0-00-08
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
       Link-local IPv6 Address . . . . . : fe80::fc76:1de8:a7c3:27dd%16(Preferred)
       IPv4 Address. . . . . . . . . . . : 192.168.135.1(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . :
       DHCPv6 IAID . . . . . . . . . . . : 352342102
       DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-2E-8E-B2-BC-5F-F4-85-5E-A8
       DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
                                           fec0:0:0:ffff::2%1
                                           fec0:0:0:ffff::3%1
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Tunnel adapter isatap.{6E06F030-7526-11D2-BAF4-00600815A4BD}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter Teredo Tunneling Pseudo-Interface:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.att.net:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . : att.net
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.{20B8F51C-F852-41EF-9F9B-1D0107550D1E}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.{8CCEC9EC-0685-4C6A-A87A-CED27B6C93E5}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter #4
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Any thoughts or help would be greatly appreciated.

    Hi,
    I'm so glad you have solved the issue in this way.
    And thanks for your sharing, your solution shared here will provie other people in this forum with a great help!
    Regards,
    Ada Liu
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • I set up iPhoto v9.6 to copy items to library. Now I would like to change it to not copy. Do I have to start completely over? I have 106GB of photos and tags in my library. Will I lose all that work?

    I set up iPhoto v9.6 to copy items to library. Now I would like to change it to not copy. Do I have to start completely over? I have 106GB of photos and tags in my library. Will I lose all that work? Originally I thought by copying items to library I would be making an exact copy of my originals and that would serve as a duplicate or backup copy. My originals are on my EHD#1 and my iPhoto library is on my EHD#2. But now I realize that I can not view my iPhoto library unless my EHD#2 is connected to my computer (duh!!) So now I would like to NOT copy times to library and I want to have the library in the Pictures folder on my laptop HD. So I guess my question is do I have to start completely over? Is there some way to salvage all the work I've done so far?

    Yes you would have to start over from scratch.
    But you should really think this through very carefully. Experienced users do not recommend iPhoto used in this mode, and with very good reasons. Among them
    1. It's more work for exactly no gain
    2. It's unreliable - especially - when the library is on one volume and the photos are on another. One change to the path between the files and the library and you'll be reconnecting every photo in the Library back to the database, one by one.
    For more on iPhoto and file management see this User Tip:
    https://discussions.apple.com/docs/DOC-6361

Maybe you are looking for