RV082 upgrade backup firmware - advanced

Good morning to everyone, I have a question for the RV082 (Primary firmware ver 2.0.0.19-tm - backup firmware ver 1.3.98-tm) and i would like to ask whether could i upgrade the backup firmware without restarting to it.In other words, how can i upgrade the backup firmware when the primary firmware is active? Thank you in advance.......

Update... I found the original firmware under the updated firmware on Linksys' website.  Downloaded the new firmware even though I'm running Win 2K. I'll post my other problem in another post.

Similar Messages

  • Choppy video streaming after upgrading E4200 firmware to ver. 1.0.03

    Video streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?

    You mentioned in your post that you upgraded the latest firmware. So after upgrading the firmware did you reset the router? It is recommended to reset the router after firmware upgrade.  Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
    After the process reconfigure the router as per the ISP setup.. Then try to do the following steps:
    A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
              1] Open the software and go to the option which says "Router Settings"
              2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
             3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page)
             4] Then go to the Wireless tab, keep network mode as mixed,
     For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
     For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
    B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

  • Upgraded to firmware 2.1 and text messages gone

    dear discussions,
    i just upgraded to firmware 2.1 and all of my sms's disappeared. it backed up for about 2 hours before the process, so i would think that i would still have them.
    does anyone know how to get them back?
    thanks in advance.

    ive heard of updating urfirmware but i dont know where to do it from... i have 2wire
    PLESASE HELP

  • NETGEAR SPH200D: Unable to Upgrade de Firmware to ...

    Hi friends !
    Please, I'm having problems to Upgrade the firmware of my SPH200D.
    The current firmware version is 1.0.4.30, and I'm trying to upgrade it to 1.0.4.80.
    I have already downloaded the file to Upgrade, but after insert the file in the WebPage, upgrade the phone, reboot the system, take the battery out... the Firmware Version is still showing 1.0.4.30 !!!
    I have tried several times, but no sucessfull !
    PLEASE, does anyone know what's going on?

    Hi Stash.
    The OS of my computer is Windows Vista Enterprise (Service Pack 2), using Internet Explorer browser.
    To avoid errors in the file, I have loaded the firmware file from more than one site... and I tried with all of them.
    PLEASE, Would be possible you send me the file that you have used ?  (my email: [email protected])
    Thanks in advance !
    My Best Regards,
    Evandroce

  • Too many errors after upgrading the firmware to 1.0.3.10 on Cisco RV180W wireless router

    My company purchased one Cisco RV180W wireless router few days ago and it worked normal with default firmware version of 1.0.0.30. Today I upgraded the firmware to version 1.0.3.10, the users can still access this router via wired and wireless devices, but on the dashboard I observed two major problems, one is the CPU utilization always shows 100%, another is the more and more errors appearing, on the Syslog Summary panel "Error" log has been up to 625 and is still increasing, there is one message repeatedly displaying in the log, see in below:
    Wed Nov 13 13:55:25 2013(GMT+0800) [rv180w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 100 failed. status=-1
    Who can tell me what does this error message mean and how to elinate this error message ?  also how to deal with 100% CPU utilization ?
    Thanks.

    Hello,
    i have been looking at different VPN routers over the last few weeks and i was very close to buying the RV180W, but then i stumbled across many posts reffering to firmware issues, one issue is that the cpu sits at 100% useage, i just wondered if this is a bug in GUI or is the CPU actually max'd out? has anyone had any resolution into this?
    also the firmware on the emulator is a newer version than is listed on the support page, does anyone know when 1.0.3.14 will be released for download?
    when i buy a new product i like to ensure that the system is fully upto date before its put into use but i obviously dont want to add any performance issues from the ofset due to the CPU useage.
    i also have a could of questions if anyone can help
    the Ipsec VPN, will this work with the Built-in VPN client for apple devices? (New IOS7), i am unable to find a quickvpn application for apple IOS.
    is the site-to-site IPSec VPN also compatible with the Cisco Wvrs4400n router?
    thanks in advance.

  • USB Share broken after upgrade to Firmware 1.05.36

    Hi, Problem after upgrade to Firmware 1.05.36.  When connecting USB disk there no share created for the newly connected disk. The result is: Broken functionality backup to USB diskBroken functionality restore from USB disk It worked OK before thefirmware upgrade (I have been using this a lot). I have checked through ssh login: the disk mounts ok. Please fix!!

    Yes, that's exactly what I mean - the shares that are automatically created when you insert the drive (ie the functionality you seem to have lost). There's no setting to enable/disable that, at least that I know of. It should just always automatically do it. The shares themselves are just links in the /shares folder, to the relevant mount folder if what I can see on my MCM via SSH is what I think it is. You may be able to manually make the links yourself via the command prompt as a work-around. Please note that I haven't tried this myself, as my one works. But what I would do is try and install the firmware image again over the top of your current one. You can download it manually from this page and then install it via the dashboard using Settings > Firmware Update > Manual Update. There should be a button there that you press and point it to the firmware image file you downloaded and stored on your local machine. If the button isn't there, try a different browser (I find on my Windows machine it doesn't appear under Chrome, I have to use IE for that job).

  • Backup Firmware

    I would like to upgrade my firmware for my WRT160N router. Linksys' firmware download says it is only for XP or Vista. I have Win 2K on my PC. 
    Should I risk doing the upgrade?Also...
    Is there a way to backup my current firmware in case the new firmware doesn't work?  Backing up my config will not include the current firmware so is there another way? 
    Will my install disk have the original firmware to restore in case things go wrong?
    Thank you! 

    Update... I found the original firmware under the updated firmware on Linksys' website.  Downloaded the new firmware even though I'm running Win 2K. I'll post my other problem in another post.

  • Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu

    Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu, for which i never kept any password. 
    Any DEFAULT Password so that i can unlock the settings menu.

    That's quite odd, just repeat the update process
    Update Service (SUS)
    http://www.sonymobile.com/gb/tools/update-service/
    http://www-support-downloads.sonymobile.com/Software%20Downloads/Update_Service_Setup-2.11.12.5.exe
    PC Companion (PCC)
    Bridge (for Mac)
    Alternatives on How to backup Xperias
    http://talk.sonymobile.com/thread/36355
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • My iphone 4 when you upgrade the firmware on ios7.0.2 produced an error 3194

    my iphone 4 when you upgrade the firmware on ios7.0.2 produced an error 3194 ... now my phone is not working ... every time an error 3194 ... I can not update ios and drop naturally I do not Pogue. hosts cleaned, cut off the antivirus ... did everything I recommend in this case ((what do I do? (
    on other machines the same ...

    Some additional suggestions here that may help if you haven't tried them:
    http://support.apple.com/kb/ts4451
    Regards.

  • Cannot upgrade the firmware.

    I am using a BEFW11S4 router Version 4. When I checked the site and after a full day of messing around I found that the problem I was having was covered in the latest update. I downloaded the bin file and tried the upgrade process from the router management. It failed. leaving the router still working but still with my original problem. Went to user groups and read what i could find. I turned off virus program, firewall and connected directly to internet to download bin file. (did this 4 times) tried again. failed. still did not upgrade the firmware and read more and downloaded the utility It could not access the router - Login failed. tried to login to router and logged in fine. spent another 4 hours trying to find any other suggestions either on the linksys site and in the forums and could not find anything. Keep in mind I have been using cisco products for about 20 years now and I am fully qualified Network technician. Please don't annoy me with any more simplistic suggestions I need a workable solution since I have about two or three hundred of these types of units out there. My interim solution was to go to staples and pick up a $49 Belkin router that works just fine. The solution suggested by the linksys person on the phone was to pay $29 to maybe resolve the issue. can anyone see the economics in that?
    P.S. went to the lela download link in the message at the top of this forum. It says to download lela click here. Did so and got a really nice demo. there was no download. so if anyone knows where to download that it might be worth a try.
    Message Edited by tekkiefirst on 07-17-2008 03:22 AM

    Try upgrading the firmware of router ... reset it & reconfigure it ... if it works ... that will be fine if not ... then possibly the router is gone bad ...

  • Upgraded to firmware 2.0+ from 1.1.5 and now my 32Gb touch won't reboot

    I tried to upgrade to firmware 2.0+. Everything looks ok while installing the firmware. The process goes smoothly. My problem shows up when the firmware is finished installing and my iPod has to do a final reboot. The screen just goes dark and doesn't come back. I've tried the process a bunch of times and it's the same result. The only way to get it back is to return to firmware 1.1.4/1.1.5. I've seen other people have the same problems. Does anybody have any similar experiences and possible fixes? Thanks.
    P.S. I don't get any weird error messages. The process goes smoothly except the iPod never reboots.

    ive heard of updating urfirmware but i dont know where to do it from... i have 2wire
    PLESASE HELP

  • FAQ Broken: How do I upgrade the firmware on a WRT54G Wireless-G Broadband Router?

    I tried to view the above question in the FAQ, but it goes to the answer for a different question.
    I then tried "How do I upgrade the firmware on my router?" a little further down,
    but it acts like I'm not authenticated, and won't accept my Linksys Forums e-mail address
    and password. When I try the password recovery, it says my e-mail address is invalid.
    Can someone please point me to instructions for upgrading the firmware on my WRT54G?
    Specifically, someone told me that the router needs to be listening on the default 192.168.1.1
    IP address, but mine is listening on 10.1.1.2. Do I need to change this just to flash new
    firmware, because that will be a little painful.
    Thanks,

    Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - "Default Gateway of Your Router"...Leave the Username blank & in Password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    **To Check the Default Gateway of the router...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
    **To all the above setting using the wired computer.

  • I updated the firmware to 5.0.1, then began a problem with my gadget I try to restore from a backup firmware, Itunes an error 3194, if I can, and if I do get to shsh ios 5?

    I updated the firmware to 5.0.1, then began a problem with my gadget I try to restore from a backup firmware, Itunes an error 3194, if I can, and if I do get to shsh ios 5?

    Good morning
    This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
    http://support.apple.com/kb/TS3125
    Hope this helps
    Cheres

  • Itunes won't detect ipod touch after upgrade to firmware 1.1.4

    I am in desperate need of help. My 16GB Ipod is no longer being detected by iTunes.
    I decided to upgrade the firmware to 1.1.4. through iTunes. The update wasn't interrupted and i can see no issues during the procedure. when the update was completed, my iPod had no content in it and it wasn't showing up in iTunes.
    Here's what i've tried so far to correct this:
    - Uninstalled iTunes and all other apple related software and then re-installed
    - tried different USB ports on my laptop
    - Reset all setting within the ipod
    - Run the iTunes diagnostic. It error's out during the sync test.
    I've tried to find any other similar example on other sites but haven't been successful.
    Please help.

    These are other hints http://www.copytrans.net/helpcopytrans.php#22
    That might help.

  • To whom it may concern I would like to inform you about an error occurred when I upgraded my firmware to IOS 6 When I plug a headphone/earphone into my, then unplug it, the volume turned out to be unadjustable I have attached 2 screenshots of the error, p

    To whom it may concern
    I would like to inform you about an error occurred when I upgraded my firmware to IOS 6
    When I plug a headphone/earphone into my, then unplug it, the volume turned out to be unadjustable
    I have attached 2 screenshots of the error, pls help?
    Thanks.

    Try a rest: Simultaneously hold down the Home and On buttons until the iPad shuts down. Ignore the off slider if it appears. Once shut down is complete, turn the iPad back on using the On button. In some cases it also helps to double click the Home button and close all apps from the tray before doing the reset.

Maybe you are looking for