RV110w wont connect with dsl modem for VPN - HELP!

Hello,
I have bought a RV110w and also a D-Link 320B modem (replacing my standard Sky broadband router) and I am having difficulty setting them up. The D-Link modem works when connected directly with my laptop via ethernet but when connected into the WAN port on the RV110w none of the computers on my network have internet access. The RV110w dashboard says that the WAN connection is "UP" and gives an IP address?? Any help with this would be much appreciated.
After the above issue has been solved I would then like to use the RV110w VPN facility which I have been unable to set up correcty using QuickVPN. The laptop that I want as a VPN client is running Windows 8.
I have been trying to sort this for two weeks with no luck!!!
Matt.

Hi Matthew, thank you for using our forum, my name is Luis I am part of the Small business Support community. I apologize for your inconvenience; I have a couple of questions, what firmware are you running? The last firmware is 1.2.0.9 and you could download it here, are the computer connected to the RV110W receiving DHCP?
I want to have this information in order to provide better assistance.
Also I will share an article for QuickVPN, here you will find the configuration for your QuickVPN
https://supportforums.cisco.com/docs/DOC-29399
I hope you find this answer useful
Greetings,
Luis Arias.
Cisco Network Support Engineer.

Similar Messages

RV110w wont connect with dsl modem for VPN

Hello,
I have bought a RV110w router and I also have a D-Link 320B DSL modem (which is replacing my standard Sky broadband router/modem) and I am having problems getting them set up correctly, firstly for the internet to work and secondly to use the VPN function on the router.
The D-Link 320B DSL modem works when connected directly into my laptop via an ethernet connection, however when I connect the modem into the RV110w the internet will not work. The dashboard on the RV110w says that the internet is "up" and gives an IP address but the internet does not work on any computer on the network. Any help here would be hugely appreciated!
After I have overcome the problem above I then want to be able to get the VPN working which I have also had no luck with.
The RV110w is set to 192.168.1.250 and the D-Link is set to 192.168.1.1. If I turn off DHCP on the D-Link I cannot then get access to the modem at all, the only way I can then get access is to hold down reset and go back to factory settings.
I have been trying to do this for about two weeks now with no luck, no matter what settings I try it just does not seem to work!!
Matt.

Dear Matthew,
Thank you for reaching Small Business Support Community.
In order to accomplish both needs, you would first need to configure the PPPoE and DHCP settings on the RV110 and set the D-Link for bridge mode only so that the xDSL negotiation is performed by the Cisco router and be the DHCP server for the LAN at the same time.
You need to first configure the PPPoE parameters on the RV110; please refer to page 23, chapter 2 of the admin guide;
http://www.cisco.com/en/US/docs/routers/csbr/rv110w/administration/guide/rv110w_admin.pdf
The required PPPoE settings are provided by your ISP and you may also copy those current settings from the D-Link modem (unfortunately I cannot tell you where they are since I am not familiar with the 320B model). You also need to set the D-Link for bridge mode since the PPPoE settings are now going to be entered on the RV110.
To set the RV110 as a DHCP server please refer to page 31, chapter 2 on the same admin guide.
You can have either a remote access VPN or a site to site VPN configured on this RV110, please check chapter 5 on admin guide. Notice for either one you would need to have static public IP addresses or a domain name provided by your ISP intended for a VPN tunnel, and in case they do provide you with neither one, then you would have to get a third party dynamic DNS service to accomplish this task. I have personally used DynDNS and it works just fine.
I hope you find this information useful and please do not hesitate to reach me back if there is any further assistance I may help you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Best Router with DSL Modem for use with AT&T DSL and Airport Express?

I recently had my old 2WIRE from AT&T DSL service die, so purchased a new 2WIRE 2701HG-B. My old 2WIRE worked with my Airport Express, which is hooked up to my DVR for DirecTV use. The new 2WIRE apparently is not compatible with the Airport Express, so I returned it and purchased a NetGear Wireless-N 300 Router with DSL modem. While this one does work with the Airport Express setup, it runs very slow. This router has mediocre reviews, so I'd like to find a better one.
I'd appreciate any suggestions for a Router w Modem that would work best with my AT&T DSL and Airport Express (802.11n) within the $100 - $150 price range. Thanks!

Configure the Express as a bridge: Connect via "Ethernet", and set Connection Sharing to "off (bridge mode)".
The switches ought not to be a problem, and I don't know why your router froze. The Express is simply another wired client, just like a computer might be.
do I turn off DHCP on the router,
No. Something has to provide routing functions so leave the Linksys alone.

My n8 wont connect with my pc..please help ooh

i have installed atheros bluetootg adapter v7.2 from hp site. my laptop connects with my phone but wont transfer file. saying unable to connect. please help i need to connect thanks

Have you tried manually installing the drivers through device manager, picking from a list of drivers and finding the microsoft generic bluetooth adapter driver?
Please give Kudos. What other kind of recognition could I get?
Have I solved your problem? Mark solution as accepted.
I try to hate Macintosh. I really do. But I can't bring myself to hate any electronic device.

Trouble using Airport Express Base Station with DSL modem, Router and Hub

About 18 months ago, I had an Airport (802.11b) with WAN & LAN ports and modem hooked up to support two laptops, a Titanium Powerbook G4/600 and G3/400. The setup went from DSL modem -> Linksys router -> to Airport -> Hub (which had desktop and ethernet laser printer plugged in). The network worked fine.
Then, I got a G4 iBook to replace G3/400. Wanted to get 802.11g to support “g” Airport card in iBook. Got a Linksys 802.11g Wi-Fi with 4-port router for $50. Hooked it up directly with DSL modem. (Couldn’t get it to send out to hub). Hooked the desktop and ethernet laser printer into Linksys Wi-Fi/router. The only way I could use the printer was by having it be a shared printer from the desktop. This was often problematic.
Two months ago, I got a refurbished Airport Extreme Base Station. I can’t get the AEBS to interface directly with the DSL modem, so I hooked it up as follows:
DSL modem -> Linksys router -> to AEBS -> Hub. I plugged my Epson 820 (USB) into the AEBS and can see it to print to.
I have a static IP. That info is entered into Linksys router. Router set as Gateway, with DHCP enabled. AEBS is set to Connect using Ethernet, Configure using DHCP. Network setting: Distribute IP Addresses is unchecked.
Here’s my issue:
I can’t see the ethernet laser printer. It will occasionally flash available, but is gone in less than a minute. The printer is HP 2100 series.
Sometimes I can connect to the desktop G4 tower; most times I can’t.
I have checked and double-checked the cables.
Both the printer and desktop are connected to the Hub.
What can I do so that I can see the HP 2100 series printer and the G4 tower?

Don,
Thanks for the suggestions. Glutton for punishment that I am, I tried this again, “just for grins.“ The six other times I tried this, I couldn’t get the AEBS to “see” the Internet. And lo, this time it worked. Here’s the setup now:
DSL modem -> AEBS -> 4-port hub (which is connected to G4 tower and HP 2100 Ethernet printer). My USB Epson is connected to the AEBS, and I can print from the laptops. AEBS is set up: manual IP info, Network: distribute IP address; share a single IP using DHCP.
When I still couldn’t see the desktop G4 and the Ethernet HP 2100 connected via the hub (not), I got a flash. I had swapped out the cable a number of times to no avail. Then I realized, the hub is old and all the cables I was using are the new CAT5s. I dug out an old four-wire with RJ45 connectors that my husband made years ago (probably a cross-over cable). It was quite an effort as the cable is 30 ft. long and wrapped around the perimeter of the office behind desks and file cabinets, entwined with all the other wires. But I plugged it in and, Shazam! I am WORKING!
And, Don, thanks to you, I have eliminated the router from my gaggle of electronic boxes.

WRT54G wont connect with xbox 360

i had my main computer hooked up to the wrt54g with a cable and had a laptop on the wireless and the xbox hooked up on a cable also. im selling the main computer and using just the laptop and now the xbox wont connect with anything. its driving me insane. at one point i had it but the xbox lost it again and has not worked at all.
do i have to have the laptop hooked up to the wrt54g for the xbox to work? when the laptop is hooked to the cable it works and when i disconnect it stops working yet i could run my old pc and this laptop wireless and xbox still worked.
i uninstalled the linksys advisor program and reinstalled and finally said screw it and deleted it and now the laptop connects finally but still no xbox.

Do the following settings on your Router for X-Box to connect...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3) Click on set-up and change the MTU Size to 1452 and click Save Settings...Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox
Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Setting up Time Capsule as router with DSL Modem as bridge

Hi All,
I want to work this out in my head before I start disconnecting wires. So let me run down what the situation and plan is. If you see a potential issue, I would appreciate the feedback.
What I have:
Verizon DSL. The DSL modem is also doing duty as the router. For a lot of reasons I don't need to get into here, I no longer want the DSL modem to be the router. I have gotten instructions on how to setup the DSL modem to serve ONLY as a bridge. In that configuration, you simply connect the DSL modem to the phone line as usual, then connect your router to one of the ethernet ports. My time capsule has been serving only as a wireless access and backup drive until now. So here is what I plan to do:
1) Connect via ethernet cable, the WAN port on the TC to the ethernet port on the DSL modem.
2) Using the manual setup screen on the TC, select the "Internet" tab.
3) Set "Connect Using" to "Ethernet"
4) Set "Connection Sharing" to "Share a public address"
5) TCP/IP set to "Using DHCP"
At this point, everything should work. At least I think it should. Am I missing something?
Any suggestions appreciated.
Thanks,
R

I haven't worked with the Verizon gateways, but configuring the device as a simple bridge might require that the Time Capsule be setup to furnish the PPPoE service. You won't know until you try.
If you are not able to "Connect Using - Ethernet", then that would be an indication that you would need to instead "Connect Using - PPPoE". In this case, you'll need to enter your user name and password that you have established with the service provider in the Time Capsule setup configuration. Be sure to leave the Service Name area completely blank if you setup using PPPoE.
If you are able to "Connect Using - Ethernet" and you configure the Time Capsule to "Share a public IP address", you may see a warning during setup that this is producing what is known as a Double NAT on your network. This is normally not too serious, unless you are trying to setup online gaming, which requires a different type of NAT setting.

Itunes wont connect with my iPod?

My itunes program wont connect with my ipod. It will charge it sometimes but after a little bit of time, sometimes the ipod will say that charging is not supported with this accesory. Also when the ipod does connect in itunes it says that an unknown error has occured when connecting to my iphone. But im connecting an ipod touch. So im really confused and thank you for any help.
Oh and its a 4th gen ipod touch that is white if that helps. i got it back in november last year.

I'm also having this problem but it seems only to have occurred once I introduced my iPad Mini to iTunes (this may have been coincidental of course!). The cable I'm using is the one which came with my iPod Touch version 4.2.1 (bought on the 23rd of July 2010) and the cable still charges the iPod as it always has. I don't have the luxury of being able to try logging in to iTunes on any other computer but I've tried absolutely everything that has been suggested in the support pages. I really want to delete some of the music from this iPod but I think I need to be able to sync with iTunes to do so. Is it just that my 3 year old iPod is just too old for the latest version of iTunes?
Any suggestions would be most gratefully accepted.

Problem connecting to DSL modem

Just finished a long session with QWest that ended with me unable to connect to my new DSL modem. Apparently there's a problem with the IP configuration settings because everything works but the computer can't find/recognize/connect with the modem. The address, subnet, router, DNS numbers QWest provided don't work. They said I had to call Apple and verify the IP configuration. But Apple doesn't answer on weekends. Is there a way to resolve this now, or do I have to wait until Monday?

yumbeerium...
Got the right cable?
This is assuming that you are connecting it via - Ethernet port, you may need a Crossover cable if the modem did not come with one.
By the way... I wonder just how Apple can help you with settings that are to be provided by the ISP? Although I believe most ISPs can use DHCP settings, you may need to ask QWest if manual settings are really necessary.
http://docs.info.apple.com/article.html?artnum=42717
...Ron

HT1178 How setup and configure time capsule with ADSL modem for WiFi internet

For my first time time capsule 2TB set up,would like to know about configuration time capsule with ADSL modem for use WiFi internet!

You will want to turn off the WiFi on your modem (if there is WiFi on your modem). Connect the TC and the modem together with an Ethernet cable. Then, turn on your TC and set it up to be in bridged mode, connection type 'Ethernet'.

I have an 08 apple desktop and my ipad mini wont connect with my itunes and i cant find updates to fix this what do i do?

i have an 08 apple desktop and my ipad mini wont connect with my itunes and i cant find updates to fix this what do i do?

From Apple's website and printed on the box the mini came in:
Syncing with iTunes on a Mac or PC requires:
Mac: OS X v10.6.8 or later
PC: Windows 7; Windows Vista; or Windows XP Home or Professional with Service Pack 2 or later
Download iTunes at www.itunes.com/download
You will have to update to at least OS X 10.6.8 or later, otherwise known as snow leopard.

Hi, My iphone has locked me out and says iphone is disabled connect to itunes. but my itunes wont connect with my iphone. i've tried everything i can think of and my phone is still locked and i cant sync it with itunes. what else can i do??

Hi,
My iphone has locked me out and says iphone is disabled connect to itunes. but my itunes wont connect with my iphone. i've tried everything i can think of and my phone is still locked and i cant sync it with itunes. what else can i do??

While connected to iTunes, try...
http://support.apple.com/kb/HT1808

My sprint sph-330 wont connect with my ipod 4g with bluetooth

my sprint sph-330 wont connect with my ipod 4g with bluetooth

That is because the iPod (and iPad and iPhone) do not have the necessary BT profiles to do that.
iOS: Supported Bluetooth profiles

My phone will be plugged up and charging but it wont connect with iTunes.

my phone will be plugged up and charging but it wont connect with iTunes.

Put it in recovery mode, that should fix it!
http://support.apple.com/kb/HT1414
I Hope I Was Able To Help You Or Solve Your Question.
Simmm
3/12/2012
EDITED
Message was edited by: Simmm

I need a request code for offline activation. Because i cannot connect with adobe server for online activation. But I receive "The request code is invalid." by generate answer code.

I need a request code for offline activation. Because i cannot connect with adobe server for online activation. But I receive "The request code is invalid." by generate answer code.

Dear Anubha,
I hope these windows illustrate what I am facing.
The above window shows the prompt that the software requires activation.
The version is 8.1.0.
This next window is the point where I select activation by phone.
This final window shows that the "response code" is not returned. I get an
"Activation Number" instead.
Steven
On Tue, Jan 27, 2015 at 10:50 PM, Anubha Goel <[email protected]>

RV110w wont connect with dsl modem for VPN - HELP!

Similar Messages

Maybe you are looking for