RV130 web interface save changes bug

When making certain changes to settings using the web interface, it gets stuck on applying them, it never returns
and one is forced to do a page refresh to get back to it, not all changes do this, but changes to vlan settings definitely do this
one is then forced to log in again, sort of, as it thinks you are already logged on

Hello,
Can you please share the page where the configuration gets stuck?
Nagaraja

Similar Messages

  • RV082 Unable to see or change settings in web interface

    I have just purchased an RV082. I am using a Mac with Safari and Firefox to access the web interface through http://192.168.1.1
    I was able to log in to the web interface using admin/admin, but the system summary page is blank.
    The category choices were visible on the left (e.g. Setup>System, Setup>Password etc... but, once again, the details area to the right is blank. No way to see what the settings are, or to change them.
    I have tried Safari and Firefox, ensuring that they were up to date for all Flash and other plug-ins that might be required to view the htm documents, but no help.
    I have reset the router in every conceivable manner:
    1. pressing and holding reset for 5 secs, or
    2. pressing and holding reset for 30 secs, or
    3. pressing and holding reset for 30 secs, powering off and back on again, then releasing the reset button
    4. removing all of the input cabling and power. Letting it sit for 2 minutes. Repowering.
    5. same as above, followed by a reset.
    6. etc..., etc... I've been at this for hours, systematically trying everything I could think of.
    The system appears to be resetting because, typically, after a reset, it will accept my login but give me blank detail pages. If I try again, it no longer accepts my (unchanged) password. A reset allows the device to recognize admin/admin again, but still only blank detail pages.
    I would appreciate any suggestions. I'm not trying to do anything fancy here, just access the web interface to change the system identifiers, password and upgrade the firmware.
    Thanks, Louis

    Hey Louis,
    Try downloading an add on for firefox.  It is called IE tab 2.  This is an internet explorer emulator.  Once you have that installed you can go to the bottom right hand corner of the page and click on the IE emulator tab.  After that, try logging into the router with that page.

  • HP LaserJet 400 MFP M425dn: bug in MTU path discovery, printer reboots via web interface

     Firmware Datecode: 20121205
    1. We can not access this MFU over VPN link. Otherer devices are accessed successfully.
    As far as I understand there is an error in MTU Path Discovery.
    tcpdump logs are attached.
    Is there a way to change MTU of this device?
    2. This MFU a  reboots when I open page "Settings" of "Networking" submenu (/hp/device/set_config_networkSettings.html?tab=Networking&menu=NetSettings) if option "System" -> "System Setup" -> "Language" is "Russian". But this looks like a very good feature since I've have not found the way to reboot this printer remotely.
    Here I was tring to access web interface over VPN (IPSec), 192.168.4.135 is IP of my comp, 192.168.160.200 - is IP of MFU, 192.168.160.254 is a gateway:
    $ tcpdump -n -r printer-1.pcap
    reading from file printer-1.pcap, link-type EN10MB (Ethernet)
    17:20:29.337867 IP 192.168.4.135.54147 > 192.168.160.200.80: Flags [S], seq 2356029847, win 8192, options [mss 1460,nop,nop,sackOK], length 0
    17:20:29.338026 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [S.], seq 614551948, ack 2356029848, win 8760, options [mss 1460,nop,nop,sackOK], length 0
    17:20:29.344909 IP 192.168.4.135.54147 > 192.168.160.200.80: Flags [.], ack 1, win 64240, length 0
    17:20:29.348488 IP 192.168.4.135.54147 > 192.168.160.200.80: Flags [P.], seq 1:304, ack 1, win 64240, length 303
    17:20:29.348564 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], ack 304, win 8457, length 0
    17:20:29.378872 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [P.], seq 1:513, ack 304, win 8457, length 512
    17:20:29.379063 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 513:1973, ack 304, win 8457, length 1460
    17:20:29.379100 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    17:20:29.379103 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1973:3433, ack 304, win 8457, length 1460
    17:20:29.379135 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    17:20:29.379251 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1:1461, ack 304, win 8457, length 1460
    17:20:29.379272 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    17:20:29.379274 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1461:2921, ack 304, win 8457, length 1460
    17:20:29.379304 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    17:20:29.379306 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 2921:4381, ack 304, win 8457, length 1460
    17:20:29.379335 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    17:20:29.379338 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1:1461, ack 304, win 8457, length 1460
     This is more detailed view on some packets.
    $ tcpdump -nv -r printer-1.pcap
    17:20:29.379063 IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
    192.168.160.200.80 > 192.168.4.135.54147: Flags [.], cksum 0x7233 (correct), seq 513:1973, ack 304, win 8457, length 1460
    17:20:29.379100 IP (tos 0x0, ttl 64, id 62678, offset 0, flags [DF], proto ICMP (1), length 68)
    192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
    192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 513:1973, ack 304, win 8457, length 1460
    17:20:29.379103 IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
    192.168.160.200.80 > 192.168.4.135.54147: Flags [.], cksum 0x5edf (correct), seq 1973:3433, ack 304, win 8457, length 1460
    17:20:29.379135 IP (tos 0x0, ttl 64, id 62679, offset 0, flags [DF], proto ICMP (1), length 68)
    192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
    IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
    192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1973:3433, ack 304, win 8457, length 1460
    17:20:29.379251 IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
    192.168.160.200.80 > 192.168.4.135.54147: Flags [.], cksum 0x0c1c (correct), seq 1:1461, ack 304, win 8457,
     P.S. This thread has been moved from LaserJets to Multifunction and All-in-One - HP Forums Moderator

    John Getzke wrote:
    Its hard to understand what you are trying to do or ask here.   We have some offices connected via IPSEC tunnels. IPSEC interface's MTU is 1280 bytes (not 1500 bytes as Ethernet). All other devices successfully work over this VPN link. HP m2727 works. HP m425dn does not work. As a network administrator I've traced source of problem on all possible points and found that HP m425dn has a bug in the "Path MTU Path discovery" routine. The logs I attached shows that any packet of the TCP stream that the printer (160.200) sends to host (4.135) has "Don't fragment" flag set. According to IP standard the router HAVE TO discard the packet with DF flag set and size bigger then MTU since it can not pass a packet further without fragmentation - IPSEC MTU is 1280 bytes only while HP sends 1500 bytes. The router informs the printer about this problem with ICMP message Type: 3 (Destination unreachable) with Code: 4 (Fragmentation needed) suggesting MTU of next hop: 1280. The router does not communicate with the printer itself, it just informs the printer about network problem. According to IP standard the printer HAVE TO resend this data with the size of packet decreased according to suggested size. This is expected behavior of the Path MTU discovery routine. But the printer  sends the packet again with the same size and DF flag set. The router again discards the packet and informs printer... This cycle repeats again and again until connection is closed due to timeout. Therefore "Path MTU discovery" routine is broken at this device. It would not be a serious problem, but the printer resends packets at rate over 28000 pps (about 40 MBytes per seconds) and its CPU is so heavily loaded that it even does not respond to touches on its touchscreen. So an innocent attempt to print document on terminal server located at another office leads to inaccessibility of the printer.
     The network dump can be downloaded in PCAP format from here.

  • Photoshop CS6 save for web some colors change?

    I have a picture with large area of color: #fffdfd, when I save it for web (jpg) this color is changed to #fefcfd (in JPG).
    I just can not save as JPG with #fffdfd.
    (was trying uncheck convert to sRGB, do not embed color profile - always #fffdfd changes to #fefcfd when save for web)
    However, color #fefcfd when save for web , does not change.
    Why some colors change and some not? Is it a bug ?
    Window7 64bit, Photoshop CS6

    Save for Web & Devices will strip some color data from the file.
    Browsers aren't color managed. Most file formats on browsers assume they're sRGB. While Photoshop gives you an option of embedding sRGB to the document color space, it also strips off data that is not relevant. This is a common occurence.
    PNG-24 on the other hand will give you the exact color match.
    Also, Save for W&D, JPG quality matters a lot - The same color at Quality 10,20,30,40,50...100 wil give you different color reproductions on the JPG end output.
    If you're concerned that much about an offset of +/- 1 hex value to your RGB colorspace, dont save for web & devices. Do a 'Save As' instead. Then use an image editing/ resizing application such as ResizeMe to resize the quality of your document. This, in most cases will retain colorspace information but just drop the resolution and quality of the image - giving you a lesser filesize.
    On a sidenote, You may also want to read this article on how to best manage color spaces: http://viget.com/inspire/the-mysterious-save-for-web-color-shift

  • Action & Droplet "save as" vs "save as web" not working - Possible bug?

    Before I state the issue, I am running the latest updates and have tried this in Photoshop CS4 & CS5.
    I believe this is a bug in Photoshop, unless someone can get this Action & droplet to work right.
    Here's the issue:
    I create an Action with the "Save as Web & Devices" and save the image as a PNG. Then create a Droplet and set the destination as "Folder" with a destination different from the source file, and check Override Action "Save As" Commands and use File Naming with Document Name + _H50 + extension (example: MyFile_H50.gif). The file naming convention I made doesn't carry over to the processed images.
    However this droplet will work with the Action when I use the "Save As" command, but not the "save as web & devices" option. Has anyone came across this issue or know how to fix it?
    The difference between "save as" and "Save as web" is a 3kb files size plus the "_H50" naming convention is not used.
    Here's a detailed process of my action and creation of the droplet:
    CREATION OF ACTION:
    1.) I have a .TGA file open with alpha channel layer.
    2.) I set the selection to the alpha channel, go back to the layers panel, double click layer, Set backgound to Layer 0, Inverse the selection, delete the background, trim image to transparent pixels, change image size to a fixed height of 50 pixels.
    Here's the variable step that works or doesn't work depending if I choose "Save as" or "Save as Web & Devices"
    3.) File > "Save as Web & Devices", save image as PNG w/ alpha, and select my "processed images" folder & save, close original  image without saving.
    CREATION OF DROPLET:
    1.) Save droplet location, Play action with include subfolders, Suppress file open options dialog, Suppress Color profile warnings.
    2.) Destination: Select a folder
    3.) Use File Naming: Document Name + _H50 + extension
    4.) Save log errors.
    Next I drag some images onto the droplet, it processes the images into the folder but doesn't use the File Naming convention.
    Now, if I use the "save as" command in the action and create the droplet the same way, it works!
    The difference between "save as" and "Save as web" is a 3kb files size plus the "_H50" naming convention is not used.
    What the heck is going on? Please Help
    -Josh

    The following example action and droplet may give you
    an idea how to do this with one droplet.
    The idea is to make an intermediate folder to save the renamed psds to.
    Then use save for web to save the psds as pngs in a different folder.
    1. Make a folder to hold the psd files (temp psd in the example droplet)
    2. Open one of your targa files and record the steps to prepare your file
        (loading the channel selection, trim, etc)
    3. Save your file as a psd.
    4. Now save the file using save for web to the folder where you want your
    final pngs to be (saved for web in the example action) and don't change
    the file name when saving.
    5. Go to the folder where you saved the png using save for web and delete that file.
       (so you don't get an overwrite message when using your droplet)
    6. When creating the droplet, specify the name you want the saved pngs to be and
       choose the destination folder where the psds will be saved. (temp psd)
    The end result of all this, should save your files, renamed as psds (to a folder)
    and save for web should save the renamed psds as pngs, to the place
    you saved the file using save for web.
    One drawback of all this, you end up with a folder full of psds.
    You could just delete the psd files inside the folder after each run.
    (click on the images below to enlarge)
    Hope this helps.
    MTSTUNER

  • WRV200 web interface crashes after changing config

    I've got a WRV200 with firmware 1.0.24. Configured to run secured wifi and a VPN tunnel, all without a problem.
    Now, when I disable the DHCP service on the box and click Save Settings I'm prompted with the "wifi will restart"message after which the web interface will stop responding. Other functionality (like VPN tunnel) stays OK. I'm connected wired and tried the change with Internet Explorer and Firefox. The only way to get access to the web UI again is do a powercycle of the WRV200. Then the config still shows DHCP enabled.
    When trying to upgrade the firmware to 1.0.29 exactly the same happens: try to apply the upgrade, then the web interface stops responding in the end... and after a reboot the f/w still shows 1.0.24.
    So: is anyone seeing the same ? And more so: does anyone know how to get around this ?

    make sure that you upgrade the firmware from a hardwired computer...
    go to ftp://ftp.linksys.com/pub/network and download the tftp.exe file .. assign a static ip address on the computer ( 192.168.1.10 ) and reduce the NIC card's speed to 10 Mbps half duplex mode...
    run the tftp.exe file...here the server is router's ip add , password is router's password....browse the firmware file and click upgrade...
    the firewall should be disabled during the complete process...
    after the firmware upgrade , reset the router for 30 seconds and do a power cycle...

  • Upload failed your changes were saved but could not be uploaded because of an error. you may be able to upload this file using server web page. save a copy

    Hi All,
    upload failed your changes were saved but could not be uploaded because of an error. you may be able to upload this file using server web page. save a copy button.
    This is the issue which I am facing while working with SharePoint 2010. In a sharePoint 2010 document library I am having an excel file and I am trying to open it from Windows 7 and is office 2010.
    I cam e across few suggestion as mentined below but unable to find the location where to do
    Go to Resource Policies > Web >
    Rewriting > Custom Headers > (if 'Custom Headers' is not visible, click
    Customize on the right top to enable the view).
    Create a new policy with the Resource as <fully qualified domain name of the SharePoint server:*/*> (for example https://sharepoint.juniper.net:*/* ).
    Create the action as Allow Custom Headers.
    Apply the settings to the required roles.
    Please suggest.

    Hi rkarteek
    All things you have to do is as follows:
    1. Open regedit.exe
    2. Naviagate to following key:
    [HKEY_CURRENT_USER\SOFTWARE\Microsoft\Office\14.0\Common\Internet]
    3. Click Edit Menu -> New -> DWORD with name of "FSSHTTPOff"
    (without quotes)
    4. Click on "FSSHTTPOff" and enter value of 1
    5.
    Close any Office Applications and browser sessions
    6. Try to reopen your document (no more read only or failure to upload)
    have a nice day!

  • Distortion in Save For Web interface

    I am still having problems with my Save For Web interface. Attached is a screen where you can see that with just the Optimized view showing (in this case 72%), the picture looks as expected. But if I go to 2-up or 4-up views, the 2nd image (which was the 72% Optimized) is now all pixelated as if it were a GIF.

    OMG!  How many years have I been using this program and I have never noticed this until now?!?
    Sorry for the brain fart and thanks for pointing that out!!! 
    I am really having a good laugh at myself about this one!
    Jules

  • Getting dump after pressing save button in web interface

    Hi all!
    When i press save button in my web interface. i'm getting dump:
    The following error text was processed in the system EDW : Syntax error in program GP1ARALDY6TX0M51YNJ5FNELBCI .
    The error occurred on the application server kurmutau_EDW_01 and in the work process 0 .
    The termination type was: RABAX_STATE
    The ABAP call stack was:
    Form: VALUE_TO_SID_CONVERT1 of program SAPLRRSI
    Form: VALUE_TO_SID_CONVERT1 of program SAPLRRSI
    Form: VALUE_TO_SID_CONVERT of program SAPLRRSI
    Function: RRSI_VAL_SID_SINGLE_CONVERT of program SAPLRRSI
    Form: GET_SID of program GP5VHI3S252BZAWN36WKBAS71QH
    Form: GET_DIMID_DA of program GP5VHI3S252BZAWN36WKBAS71QH
    Form: WRITEIC of program GP5VHI3S252BZAWN36WKBAS71QH
    Form: WRITEIC of program GPEP1KAM5Q04J9717R7T5PDWE0W
    Form: APO_WRITEIC of program GPEP1KAM5Q04J9717R7T5PDWE0W
    Method: _WRITE_TO_CUBE of program CL_RSDRI_INFOCUBE=============CP
    Infocube and web interface were imported from BW3.5 system...
    How can i solve this problem?
    Thanks in advance...

    Go in ST22 and post the short dump to better ubderstand.
    Regards

  • Trigger a process chain when user clicks on save button in web interface

    Hi All,
    This is a issue I'm facing with the BW BPS web interface.
    BPS web interface generates a BSP application so thought posting this question in BSP forum might get some responses.
    The issue is I have to trigger a process chain when the user clicks on the save button on the web interface.
    I have no clue how BSP works. So if anybody has any ideas or suggestions I would greatly appreciate it.
    Thanks,
    Harini

    Hi Dhanya,
    This is the code i have in the ABAP program in the process chain. I just included the API_SEMBPS_POST part, but still it doesn't work. Please give me your email address so that i can send some screenshots.
    REPORT  ZHTEST.
    DATA: l_subrc TYPE sy-subrc.
    DATA: ls_return TYPE bapiret2.
    CALL FUNCTION 'API_SEMBPS_POST'
    IMPORTING
       E_SUBRC         = l_subrc
       ES_RETURN       = ls_return.
    CALL FUNCTION 'RSAPO_CLOSE_TRANS_REQUEST'
      EXPORTING
        I_INFOCUBE               = 'ZMAP_TAB'
    EXCEPTIONS
      ILLEGAL_INPUT            = 1
      REQUEST_NOT_CLOSED       = 2
      INHERITED_ERROR          = 3
      OTHERS                   = 4
    IF SY-SUBRC <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
            WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.

  • IOS 4.2.1 auto-correction bug in gmail web interface

    Seems to be a bug in 4.2.1, relating to auto-correction of spelling errors within the gmail web interface (i.e. within safari)...
    Whenever I'm typing, if I make a spelling error for which auto-correction suggests an alternative, attempting to cancel the auto-correct by hitting the little X icon next to the suggested word has no effect - the suggestion stays there... the only things that can be done are to either (a) backspace and retype the word correctly, or (b) hit space and allow the erroneous correction to be made.
    Auto-correct appears to work fine for other sites accessed within Safari, and also other apps... seems to just be isolated to the gmail web interface (at least as far as I'm experiencing atm)
    Anyone else noticing this? Any workarounds or fixes suggested?

    I'm experiencing exactly the same problem on an iPad running iOS 4.2.1 (8C148)--- exactly as you described: I can't cancel individual autocorrections. This is a major problem with typing on the iPad, because it's hard to be precise with the keyboard, but technical words need to be canceled. It happens in gmail, but not some other text boxes in Safari, such as this one.
    -- Jim

  • E4200 Web interface port wont change

    Howdy yall,
    I was wondering if there are any known issues regarding the linksys e4200 web interface accessibility.
    I am trying to configure the web interface for outside access, but i want the port to be: 2000
    So i changed the port, but when i type my external IP in the webbrowser, without a port, i still get the username/password
    prompt window. This is in the standart 80 port, even though i changed the port to 2000.
    Also, when i type my external IP including port number 2000, the connection fails.
    The problem is, the webserver in the router running the web interface, refuses to change to port 2000
    It doesnt matter whether i restart the router after the change, or not.
    Does anyone  have any clue about the root of the problem ?

    Never mind, it appears that for some reason my browsers connect to the routers interface directly. no matter what url i use.
    An online port scan reveiled that the port did in fact change, so there is no problem.

  • Mailman web interface now saving changes

    Hi,
    On our server, Mailman is working fine (it sends out mail to those on the list), but the web interface does not work. I can log in to the web interface, but any changes I make will not take. I can not approve or delete messages, and I can not change the settings in the administrative section. I have tried in Firefox, Safari and in Explorer. I have CGI enabled on my site. Any ideas on why I can not manage the lists?

    I've had the same problem on some of my virtual domains for a long time. I suspect that if you use multiple domains on your server then you're likely to encounter this problem. It seems that mailman is really picky about the domain names matching. I found my fix on this thread:
    http://discussions.apple.com/thread.jspa?threadID=131327&start=5
    The part that worked for me was the fix_url command of withlist. So if you have a mailing list named 'foobar' and your domain is example.com then you would type this:
    sudo /usr/share/mailman/bin/withlist -l -r fix_url foobar --urlhost=example.com
    Don't ask me what it does but it seems to fix this particular problem. Hope that this helps you like it did for me!

  • What's the best out-of-the-box web interface for a SQL DB?

    I'm developing a Java web application that will be backed by an Oracle database. Users would like a simple web interface that allows them to accomplish what they could with SQL queries without knowing SQL. The basic operations would be:
    * displaying a database table in a table format
    * downloading the table as a text or Excel file
    * customizing the columns in a table display
    * displaying a query result set in a table format
    * constructing a query using drop-down menus
    I'd probably want to program in a simplified UI for a few common queries.
    This really looks like functionality someone should have invented before me. Question: what is the right tool for me to be using? I'm surprised I haven't found something by searching.
    It looks like I could just directly write JSP, but I think something else might be simpler. I think related functionality exists in Spring, but I didn't find exactly what I'm looking for, and Spring brings a lot of other stuff also. Nothing in my application is more complicated than this, so I'd be happy to keep things simple.
    How would you write this?
    Edited by: 1010007 on Jun 5, 2013 7:22 AM

    Welcome to the forum!
    >
    I'm developing a Java web application that will be backed by an Oracle database. Users would like a simple web interface that allows them to accomplish what they could with SQL queries without knowing SQL. The basic operations would be:
    * displaying a database table in a table format
    * downloading the table as a text or Excel file
    * customizing the columns in a table display
    * displaying a query result set in a table format
    * constructing a query using drop-down menus
    I'd probably want to program in a simplified UI for a few common queries.
    This really looks like functionality someone should have invented before me. Question: what is the right tool for me to be using? I'm surprised I haven't found something by searching.
    It looks like I could just directly write JSP, but I think something else might be simpler. I think related functionality exists in Spring, but I didn't find exactly what I'm looking for, and Spring brings a lot of other stuff also. Nothing in my application is more complicated than this, so I'd be happy to keep things simple.
    How would you write this?
    >
    I wouldn't write it. I would just use Oracle's FREE Apex application which does all of that and more and is fully supported even on Oracle's FREE Express edition data database.
    http://www.oracle.com/technetwork/developer-tools/apex/overview/index.html
    >
    About Application Express
    Oracle Application Express (Oracle APEX), formerly called HTML DB, is a fully supported "no-cost" option of the Oracle Database. Oracle Application Express is certified against all editions of the Oracle Database 10.2.0.3 and above, including Oracle Database 10g Express Edition (Oracle XE).
    Oracle Application Express installs as part of the seed database installation with Oracle Database 11g.
    >
    The feature page (http://apex.oracle.com/pls/otn/f?p=4600:6:0) describes some of the major features of Apex
    >
    Browser Based
    Using only a Web browser and limited programming experience you can develop data centric applications in minutes. Browser-based development enables you to develop applications on most computers using only a modern Web browser.
    Rapid Application Development (RAD)
    Use simple wizards and declarative programming to create powerful reporting and data entry applications. You can create applications from spreadsheet uploads, or on existing database tables and views. Oracle Application Express includes SQL Workshop to create and manage the database objects that support your application.
    Application Express Components
    Application Builder - Database Applications
    Application developers use wizards to declaratively assemble applications organized in pages. Page content is organized into regions. Regions can contain text, custom PL/SQL, reports, charts, maps, calendars, web service references or forms. Forms are made up of fields (called items) which can be selected from the multitude of built-in types (such as text fields, text areas, radio groups, select lists, check boxes, date pickers, and popup list of values) or a developer can create their own types using plug-in support. Table update functionality is built-in and PL/SQL can be used to process data. Session state (or application context) is transparently managed and the user interface presentation is separated from the application logic so that the look and feel of an application can be changed simply by selected a different theme.
    Application Builder - Websheets
    Using Websheet Applications, end users can manage structured and unstructured data without developer assistance. Page sections contain unstructured data and are edited using a WYSIWYG editor. Reports provide access to database data by writing SQL. Data Grids can manage structured data without writing SQL. Adding columns, renaming column, and validations are defined using runtime dialogs. Each page and row of data grid data can be annotated with files, tags, notes, and links. Pages can contain sections as well as reports and data grids and all can be linked together providing navigation. All information is searchable and completely controlled by the end-user.
    SQL Workshop
    The SQL Workshop provides tools that enable you to view and manage database objects. Object Browser enables you to use a tree control to view object properties and create new objects. The SQL Command tool enables you to enter ad-hoc SQL. Query Builder enables you to create join queries using drag and drop. SQL Scripts enables you to store and run scripts. The Data Workshop enables you to load and unload text, DML, and spreadsheet data.
    RESTful Services
    RESTful Services allow for the declarative specification of RESTful services mapped to SQL and PL/SQL.
    Team Development
    Team Development helps manage the life-cycle of an application's development. It provides tracking and management of application features, to do entries, bugs, and end user feedback. Team Development is tightly integrated with the Oracle Application Express Application Builder. For example, edit page lists open feedback, bugs, and to do's.
    Administration
    Each Oracle Application Express workspace is a separate application development environment that is fully insulated from other workspaces. The administration component provides workspace management, including services (available schemas, space requests, and preferences), users (both developers and end-users), and workspace activity (page views, login attempts, and developer activity). Access is limited to Oracle Application Express developers who have workspace administration privileges.

  • Deliver report to Content Store directly with web interface

    Hi all,
    We are currently implementing a system which will use XMLP as the letter/report/document producer. XMLP will be accessed from other applications (Siebel, EBS or else) using a preformatted URL so that the user will be in context of the report/letter directly. We would like the user to generate the report using the parameters in the XMLP web interface and when the report is ready, that there was only a "Send" button which would put the report in a temporary folder in a Content Store (Oracle Content DB). We would like to achieve that without the user having to input the destination of the file, like with a WebDAV or FTP. So we need to customize XMLP to remove the "Schedule" button and change the behavior of the "Send" button.
    We would also need to be able to send the context of the creation of the report in order to be able to store it at the right place in the Content Store. In order to do that, we would pass an Id by a query string in the URL when calling the report. I know this information is stored in the XMLP_SCHEDULER_JOB table in the DELIVERY_PARAMETERS field so it must be accessible in the app as well. A BPEL process would be used to move the document to the right place.
    So, 2 questions:
    - Is it possible to change the behavior of the "Send" button? Has anybody done that?
    - How can we save the context of the execution of a report to a file at the same time we are generating the report? (parameters used, template used, etc.)
    Any clue, hint or helpful thought would be very appreciated!
    Thanks!
    Pierre-Yves

    Hi MadhuSudan,
    I couldn't find the EBS Delivery you are refering about. Is this something using the Concurrent Manager from EBS? If so, this is not what I am trying to do. I really want to give access to XML Publisher and save the output report the user has made with the parameters he used to create it in order to store it in a content store. XMLP will be accessed by EBS and Siebel through a URL.
    I am curious to look at your java program and shellscript, could you send me a link to the URL where I can find the information you were refering to?
    Thanks!
    Pierre-Yves

Maybe you are looking for