RV180W and 802.1x with Windows NPS

I am attempting to configure a Cisco RV180W with 802.1x authentication using peap-mschap-v2 with a server 2008 nps box in a domain environment and I keep getting the following error in the event logs: "The RADIUS request did not match any configured connection request policy (CRP)." I do have my Connection request and Network policies in place and they do work when using a Cisco 1142N. Does anyone know if the RV180W supports this type of configuration?
Jose

I believe the problem should be solved with the new phone firmware:
Ref Cisco Document:
http://www.cisco.com/en/US/products/hw/phones/ps379/prod_release_note09186a0080461f84.html
"Firmware release 7.2(2) provides support for the Cisco IP Phone models 7960G and 7940G to monitor IEEE 802.1X messages between an authenticating switch and a connected PC (supplicant).
When a PC is disconnected from the Cisco IP Phone, the phone issues an EAPOL-Logoff message on behalf of the PC to the authenticating switch.
Hope This Helps
Jarle Steffensen

Similar Messages

Can i use a thunderbolt display for my macbook pro and hp laptop with windows 7 and what adapters will i need

Can i use a thunderbolt display for my macbook pro and hp laptop with windows 7 and what adapters will i need

Hi jayhrab,
Currently, the system requirements listed for an Apple Thunderbolt Display are:
Thunderbolt-enabled Mac computer, including MacBook Air, MacBook Pro, Mac mini, and iMac
OS X v10.6.8 or later
Apple - Thunderbolt Display - Read the tech specs.
Regards,
- Brenden

My desktop IMac OSX 10.6.8 : IMovie '11: Trying to upload a home movie clip from my Panosonic camera model PV-DV203D. I've had this camera several years, and used it with Windows desktop. Now trying to work with my Mac. I have a USB cable, both ends fit,

My desktop IMac OSX 10.6.8 : IMovie '11: Trying to upload a home movie clip from my Panosonic camera model PV-DV203D. I've had this camera several years, and used it with Windows desktop. Now trying to work with my Mac. I have a USB cable, both ends fit, but iMovie '11 does not recognize it. Is there a driver fix for this?

What kind of Mac to you have? This camera is a tape based DV one that connects best with firewire and I cannot tell if your Mac has firewire. If your mac *does* have firewire, get a camcorder firewire cable and try again.
ETA: Oops, I am pretty sure that all the "desktop iMacs" have firewire, so you should be good to go. You will probably need a cord that goes from FW800 to your camcorder.

Are Photoshop CS5 and CS6 compatible with Windows 8

Are Photoshop CS5 and CS6 compatible with Windows 8?

Yes, I'm running CS6 on 8.1, and I'm sure CS5 works as well.

I have a iPhone 5C and a PC with Windows Vista.I did pair my phone thru Bluetooth but when I try to connect I get this message:"error establishing connection" What is the reason of this?

I have a iPhone 5C and a PC with Windows Vista.I did pair my phone thru Bluetooth but when I try to connect I get this message:"error establishing connection" What is the reason of this?

Go into Settings>Messages>Send and Receive and make sure that your phone number is checked and iMessage reads as activated. Remove the checkmark from the email address and make sure that only the phone number if checked. It should appear grayed out, but should still have a checkmark. If the phone number does not have a checkmark, then turn off iMessage, wait a few moments and then turn iMessage back on and make sure that it activates.

X-Fi XtremeMusic and SPDIF bypass with Windows 7

Hello
I moved from Windows Vista to Windows 7 (64 Bit) now I wanted to use the SPDIF bypass option with the Digital I/O Module again, but in the "SPDIF E/A" tab the drop down box "Settings for SPDIF input" is disabled.
What I need to do to get the SPDIF bypass to work again?
(I don't need any Dobly/DTS decoding - it's just a simple?PCM signal.)
Best regards and thanks in advance
Andreas

Re: X-Fi XtremeMusic and SPDIF bypass with Windows 7l Hello hwoarang5,
why do you think that this is disabled in Windows 7 and Vista?
It worked fine in Windows Vista, too.
Anyway, I've searched yesterday evening?a little bit more and solved the problem myself. To enable SPDIF bypass you have to do the following:
. enable Digital Input in the Windows 7 sound settings (it'sis disabled by default and I forgot about it).
2. change the FlexiJack mode in the audio settings of Creative to "Digital E/A".
3. now enable the "Recordation with bit adjustment" (don't know how this is called exactly in the English version).
When there is a PCM (DTS and Dolby is not supported) signal now at the Digital Input you should here something now.
Hope this helps somebody.
Best regards
Andreas

Can I upgrade to maverick, and still working with windows partitions without any problem?

I have a MacBook Pro runing Mac Os 10.6.8, and a partition runing windows 7, I want to Upgrade to Maverick.
Can I upgrade to maverick, and still working with windows partitions without any problem?

yeah I installed win7 64bit pro on lion and have since upgraded osx to mtn lion and then mavericks
and the windows partition to win8 and then win8.1 never done a reinstall of anything

Wireless 802.1x with Window 7

I have a WLC 6.0, ACS 3.3 and the SSID is setup to use 802.1x with Peap Authentication. The clients are using Windows 7 to connect to wireless. To get the clients connected they have to go into there network properties if the wireless card, configure the client to use PEAP, uncheck validate server certificate, and also uncheck use computer name to login into windows. This works fine and the user to able to connect to to wireless after dong all these steps and then entering in there Windows Username and Password. The customer is saying that this is to many steps for the end user and they just want the user to to click on the SSID and connect. If wireless could also be setup to use there windows username and password would be a bonus. I'm basically looking for a solution that is simple but is also secure as well. I know that's an oxymoron. Is there anything I could do to make the wireless process simpler. Either by going with a different security authentication or by doing something different on the clients computers. Thanks for any help and suggestions.

This is a script that we use on our campus (University of Leeds), that self configures an 802.1x connection and when a user connects to an 802.1x connection merely asks them for their username and password, which then remained cached.
The .exe you create takes away all the techy bits that do 'confuse' some users, even if they are provided with well written documentation.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
https://sourceforge.net/projects/su1x/
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
http://lsayregj.swan.ac.uk/su1x/SU1X_User_Guide-v104.pdf
Features include:
- Automation of configuration of a PEAP wireless connection on XP(SP3),Vita and Win 7
- Can set EAP credentials without additional user interaction (avoids tooltip bubble)
- Installation of a certificate (silent)
- Checks for WPA2 compatibility and falls back to a WPA profile
- Third party supplicant check -SSID removal and priority setting
- Support tab: (checks: adapter, wzc service, profile presence, IP)
- Outputs check results to user with tooltip and/or to file
- Printer tab to add/remove networked printer
This tool is very cleverly written by Gareth Ayres at Swansea University

Adobe After Effects CS5 Crash and compatibility problems with Windows 7 64-bit

Hello,
I get a lot of crashes of After Effects CS5. I get the message thar Monitor Kernel program stopped responding and recovered.
I also did a compatibility test and found that After Effects CS5 is not compatible with Windows 7 Premium 64-bit.
Could you suggest a solution please?
Thank you
Giannis Stravolaimos

I solved the problem by myself.... as usual

Ipod will not be recognized and is screwing with window xp

One day my iPod reseted itself when my computer crashed, and when the ipod turned back on it deleted everything on it and went to "chose language".
Windows will not recognize ipod most of the time (sometimes randomly sees it in explorer, but I can't do anything with it)
Ipod interferes with my windows start up and shut down (comp will not fully startup or shut down unless ipod is disconnected)
Here is what I tryed:
Restarting iPod - just resets back to "choose language"
Restore/update software - crashes when I reset the ipod when connected, other then that it just asks for an ipod to plug in even when my pod is pluged in
Disk mode - does not seem to matter when connected to computer
diagnostic mode - tests seem to show everything is fine
Diffrent computer that my iPod was already registered on and worked fine with before - no cigar
Uninstalling and then reinstalling all ipod stuff - yeah... not working
Now in the process of writing this my iPod seems to be getting recognized. iTunes just launched, autoplay started up, and xp explorer sees it, but explorer freezes when i try to do anything.

Have a look
http://discussions.apple.com/thread.jspa?messageID=2001071#2001071
Changing the iPod drive may helps

Bad PBR sig and dual booting with Windows

This site's menu config is too difficult for me...
fyi.
=>
Below is the cases that happened in my environment
when installing Solaris 8 Operating Environment, Intel Platform Edition
Some will help you, and some may be just for your thinking.
Bad PBR sig
You know what it means?
I don't know.
If you know, let me know please...
@ Case 1
My Seagate ST39236LW 9.2GB HARD DISK fdisk info
Total disk size is 14342 cylinders
Cylinder size is 1251 (512 byte) blocks
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
1 IFS:NTFS 0 7165 7166 50
2 Active x86 boot 7166 7182 17 0
3 Solaris 7183 14341 7159 50
(I use cylinder number to partition hard disk. Why?
When I use % and insert 1% to partition 2 then
fdisk makes start cylinder 7155.
It overlays with partition 1's end cylinder number.
So fdisk save(menu no 4) fails...
because the partition 1's start cylinder number is 0 ?)
After rebooting, bizarre Bad PBR sig, and my system dies...
So I boots my PC with Windows(or Dos) booting diskette.
A> fdisk
First Hard Disk partition info
1 NTFS 4377 50%
2 NON-DOS 10 0%
3 A NON-DOS 10 0% <= Solaris created x86 boot
4 NON-DOS 4363 0%
Solaris created extra X86 boot partition 3 and made it active.
But partition 3 could not boot...
I made partition 2 active from dos fdisk menu,
and pc boots well.
After rebooting, my disk partition info is like this
Total disk size is 14342 cylinders
Cylinder size is 1251 (512 byte) blocks
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
1 IFS:NTFS 0 7165 7166 50
2 Active x86 boot 7166 7182 17 0
3 x86 boot 7183 7199 17 0
4 Solaris 7200 14341 7142 50
Then after installation?
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
1 IFS:NTFS 0 7165 7166 50
2 Active x86 boot 7165 7181 17 0
3 Solaris 7200 14341 7142 50
Partition 2 and 3 changed...
Where did partition 3 go???
Just deleted?
Then why partition 2 Start cylinder changed?
@ Case 2.
Another queer thing....
Total disk size is 14342 cylinders
Cylinder size is 1251 (512 byte) blocks
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
1 IFS:NTFS 0 7165 7166 50
2 Active Solaris 7166 14341 7176 50
In Solaris x86 format fdisk menu,
if I've allocated remaining disk space all to Solaris(without x86 boot),
then Solaris also makes x86 boot partition(size 10MB), reboots well.
But install fails due to not enough free disk space
when install begins slicing Solaris partition.
error log says
Installing 32 Bit Solaris Packages
- Configuring boot device
- Using disk(c0t0d0) for "rootdisk"
- Deleting x86 boot fdisk partition (c0t0d0)
- Creating x86 boot fdisk partition (c0t0d0)
ERROR:Not enough free space to create x86 Boot fdisk partition(c0t0d0)
Why does Solaris delete and create x86 boot partition?
Why did it exist?
Case 3.
If I've fdisked like this, what will happen???
Total disk size is 14342 cylinders
Cylinder size is 1251 (512 byte) blocks
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
1

BAD PBR SIG message comes from your BIOS - no partition boot record.
Sorry but it's not clear what else is going on - might be worth running a ODS based fdisk to clear the disk before installing Solaris?

[SOLVED] RTC and dual booting with Windows 8/8.1

I am planning ahead of installing Arch on a windows 8.1 laptop, and need to understand whether or not the known Windows registry hack to get windows to use UTC for the RTC is still valid for Windows 8/8.1? I have been searching via google and the usual sources of information, but it is not clear to me if there are problems doing this, specifically if arch is dual booted with Windows 8/8.1 rather than older versions of the MS OS. Certainly I have used the technique without any problem in the past when dual booting Windows XP with Arch on several different machines.
Does anyone have personal experience with doing this on a Windows 8 or 8.1 machine and can report here on whether it works successfully or not?
Thanks for any advice.
Last edited by mcloaked (2014-02-11 21:16:21)

Since there were no replies at this point I thought I would just go ahead and implement the registry hack on the Windows 8.1 O/S in the laptop and see if Windows behaves. It appears to be OK, with the displayed time being correct after reboot, and time synchronisation remaining fine with no problems seen in the displayed time, although I won't be able to read the RTC directly until I have completed the Arch install in the coming week or two. I now don't foresee any issues with the time synchronisation between booting Arch and Windows 8.1 so I will mark this as solved.
Since the RTC is now in UTC then normal clock config in Arch using chrony should perform normally once the install is done and the new system set up.
Last edited by mcloaked (2014-02-11 21:17:11)

PDF opens and works correctly with Windows 8 Reader, but not with Adobe Reader. Why?

Hi,
My sister-in-law has this PDF order form from one of her company's distributors that opens and allows editing of specific fields.
The only application that opens the file correctly (visually and functionally) is the Windows 8 Reader. If I open the file in Adobe Reader or with the Mac viewer things do not line up, fonts are too large, and when editing fields sometimes symbols show up and sometimes way over-sized numbers show up.
This behavior has been observed on both a Windows 8.1 PC as well as on a Mac Book Air.
Can someone please tell me why this is happening? Is there something that needs to be configured differently?
Thanks,
Matt

This is what I see when I open that PDF in Adobe Reader 11.0.07:
Can you tell me which parts are not correct? Obviously the Submit button is a bit strange.

I want to use iChat video and file sharing with Windows users

Nowadays, iChat is compatible with AOL/AIM, Google Talk, Jabber, Mac.com and MobileMe instant messaging services. I know that Yahoo Messenger support will be available soon in Mac OS X Lion.
I tried using AOL/AIM and Google Talk natively in iChat in order to talk with Windows users which were using Google Talk application or web chatting (Me from: Google Talk - My friends from: Google Talk, and Me from: AOL/AIM - My friends from: Google Talk), but videoconference and file sharing were not available.
I also tried Windows Live Messenger in iChat via Jabber intermediate, but it is not efficient and doesn't work for videoconference and file sharing.
So, which IM service combination I should use to chat with Windows users in order to be able to use videoconference and file sharing using such a great app like iChat?
Thanks you.

Hi,
A lapsed Trial or lapsed Paid for MobileMe account will not work in any fashion, as a Screen Name in iChat/AIM apps or as a Email. (Of course it is no longer an Valid Apple ID either).
Given that Google is a Jabber server iChat will Video (or Audio Only) Chat Jabber to Jabber.
With a Valid AIM name (AIM, MobileMe or @mac.com) then it is supposed to work to AIM on a PC
This tends to vary from person to person as to success.
From AIM version 6.5 AIM introduced a Send as Typing feature called "Real Time"
It does not work to iChat and in fact also has to be turned Off in the Buddy List at the AIM end for Video or Audio chats to work.
The AIM app also has to be allowed through the Windows Firewall as an Exception, preferably with UPnP enabled as well and UPnP enabled in their Router.
Trillian is a paid for App for PCs that provide an alternative.
Recently theri site offered 3 windows versions
The Pro version of verion 3.2 (known to work), a version 4 and a version 5 in beta. The version 3.2 used to have a free Text chat version and only the Pro version was needed to Video.
Until the site was reorganised the 3.2 version was "On Sale" at a reduced price.
It seems version 5 is now out of beta
They are still separating out a Pro version.
It is a multi-service client
There is also a Mac version although I have not tried it.
I am not sure what you mean by "Manage" your MSN Contacts.
How about using a MobileMe expired account screen name for using iChat with Windows-Google Talk users? Should I expect the same incompatibilities?
I have already addressed part of this. The fact the name will not work full stop.
However one way of reading this is that you are thing of linking AIM and Jabber (Google) Buddies in one Buddy List
Directly in iChat this cannot be done - unless you are the one with the Jabber Account and an AIM Transport set up.
You would be subject to the same Text Chat only restrictions.
It is a bit like the fact your phone line can be used for Fax, Telephone and DSL broadband. (in fact mine does TV as well)
You granny would not be able to talk to your Fax machine if that happened to answer the call.
Her Fax machine might be able to communicate with your computer if you had an active Fax app on there, and a dail-up modem active to answer.
10:06 PM Tuesday; May 24, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
 Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Photoshop element 10 and 11 work with windows 8?

Does photoshop element 10 & 11 work with windows 8?

I have both pse 10 and pse 11 installed on windows 8 x64 and they both seem to work fine.

RV180W and 802.1x with Windows NPS

Similar Messages

Maybe you are looking for