RV220W not showing DHCP Leased Clients (LAN)

I have notice that when I click on Networking -->LAN -->DCHP Leased Clients (LAN) I get 0 results found, but If I click on Status-->Avaiable LAN Host I see all my clients, most (all but 1) are listed as "unknown" under the Name.
How do I get them to show up under the DCHP Leased Clients (LAN)?

Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center.
First, Thank you for purchasing a Cisco product. I am sorry to here that you are still having the issue. I am going to follow-up with the agent that was working your case and work on determining what is causing your issue.
If you need anything, please let me know. You can reach me at emoyers at cisco . com
Eric Moyers
Cisco Network Support Engineer
1-866-606-1866

Similar Messages

Why available Lan Host not showing up in the DHCP Leased Client table for RV180

I just purchased the RV180 and am puzzled as to why lan host with ip address of 192.168.1.102 not showing up in the DHCP leased clients list.
I have 4 static ip addresses with the last 3 digits ending in 101, 102,103 and 200 listed in the static DHCP and available local network list, but 102 is not in the DHCP leased clients list. The other 3: 101,103 and 200 are.
Should it not be there also?

Thanks Marty,
There is nothing different about 102 than the other hosts.
I did talk to tech support at Cisco this morning and I was told that I should not use the static DHCP under Networking LAN. Instead, I should set the static IP at the device level.
So under Static DHCP, the list is blank, but the IP address will show up under Available LAN Hosts and listed as Static as Type.
I thought this is a bit strange since it is Static DHCP and should be under Static DHCP (?)
George

WLC2504 clients not receiving DHCP leases

I'm stock with a 2504 using version 7.0.220.0 that won't lease out DHCP adresses
Wifi clients are unable to get a DHCP lease from an external DHCP server.
The WLC are handling 3 WLAN, 2 using internal DHCP server, 1 (that wont work) using external DHCP. The external DHCP server, is a router/firewall (out of my reach) that suffered from a power out, a short while ago, ever since the DHCP is not working on that VLAN, if client are getting static ip adresses, everything works fine. If i'm using the same network link, and plug it into a computer, I get a DHCP address.
I've enable DHCP proxy
Debbuging DHCP, using: Debug DHCP packets enable
Gives me this:
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP received op BOOTREQUEST (1) (len 308,vlan 20, port 1, encap 0xec00)
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option len (including the magic cookie) 72
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: message type = DHCP INFORM
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 61 (len 7) - skipping
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 12 (len 1) - skipping
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: vendor class id = MSFT 5.0 (len 8)
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 55 (len 13) - skipping
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP options end, len 72, actual 64
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
Thanks

Hi Steen,
When a client is in DHCP REQ state on the controller, the controller drops DHCP inform packets. The client will not go into a RUN state on the controller (this is required for the client to pass traffic) until it receives a DHCP discover packet from the client. DHCP inform packets are forwarded by the controller when DHCP proxy is disabled.
Please check this, if still u r facing issue then provide more info.
Can you please paste a client debug of the client having DHCP issues.
Go to cli of the wlc and run the client debug . Diconnect the client then reconnect and gather the output and post.
Regards

AP 1231G Not Passing DHCP to clients

Hello My company AP 1231G is not passing the DHCP address to the client from the DHCP server can you please advise on my config listed below
basicly the AP is on its own VLAN 10.1.123.1 and the DHCP server is 10.1.10.2 -- trying to use iphelper to pass DHCP to clients and the AP is on static IP 10.1.123.2--
! Last configuration change at 13:15:56 +0800 Fri May 25 2012 by root
! NVRAM config last updated at 13:15:56 +0800 Fri May 25 2012 by root
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXXXXXXXXX
clock timezone +0800 8
ip subnet-zero
no ip domain lookup
ip domain name XXXXXXXXXXXXX
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 syslog
dot11 ssid XXXXXXXXXX
   authentication open
   authentication key-management wpa
   guest-mode
   infrastructure-ssid optional
   wpa-psk ascii XXXXXXXXXXXXXXXXXXXXXXX
dot11 arp-cache optional
username root privilege 15 password XXXXXXXXXXXXXXXXXXXXX
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid XXXXXXXXXXX
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
no preamble-short
channel 2432
station-role root access-point
no dot11 extension aironet
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.1.123.2 255.255.255.0
ip helper-address 10.1.10.2
ip default-gateway 10.1.123.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
access-list 111 permit tcp any any neq telnet
snmp-server view dot11view ieee802dot11 included
snmp-server view ieee802dot11 ieee802dot11 included
snmp-server community public RO
snmp-server community private view undefined RW
bridge 1 route ip
line con 0
terminal-type teletype
line vty 0 4
terminal-type teletype
sntp server 114.80.81.13
sntp broadcast client
end

Roan:
Where is your DHCP server configured (swtich, firewall, 3rd party server..etc)?
Does it work correctly if the AP IP on same subnet and ip-helper is not being utilized?

Field description changes not showing on one client only

Hello!
I have a network with several clients all running SAP. I have modified lots of field descriptions (by pressing CTRL double click on the field).
This is great - except I have one PC where the field descriptions show the original text, rather than my updated descriptions. This happens even when other SAP users login to this PC.
Can you explain why one PC is not showing the modified field descriptions?
Thank you
Omam-B

What do you mean? I have restarted the PC and reinstalled SAP.
What else is there to restart?
Thanks

Unified Communications Attendant console: queue does not show in the client

Hello,
I have Cisco Unified Attendant Console - Department Edition 9.1.1.10 in conjunction with CUCM 9.1.1.
My problem is that when I login with the operator account to the client the queue does not show up as expected.
I have configured the queue, synchronized with CUCM, i can see it in CUCM under device/CTI route point, i have associated the queue to the operator in user configuration queue association.
but when i login as the opeartor to the client i can not see it.
any help is apreciated.
thanks

Hi,
This is working correctly, as you can only associated a single queue (department), this is not displayed in the operator console client.
You only see the queue list in Business, Enterprise or Premium Edition.
Jamie

Notification not showing on XP client

Hi
I got SCCM 2007 r3 setup and it see's the client pc which is Windows XP but when I am trying to push out a windows update , a notification is now showing on the client machine , is there something I missed on this?
Thank you.
DJ SAI

Hi,
Is it only for Windows XP clients that the popus are not showing? or do you have other clients with other versions? For Windows xp it was popular to disable balloon notifications which could affect it. You can also select to "hide all notification for
end-users" under Client agents, software update agent..
Regards,
Jörgen
-- My System Center blog ccmexec.com -- Twitter
@ccmexec

WLC2100 not issuing DHCP to clients

I've got a 2106 that I'm installing for a customer and having issues with it assigning DHCP to WiFI clients. What's odd is that this was working at one point at home during testing. Only difference at this point is LAN hardware at the customer location.
Simple config- single flat vlan on Cat2960G switch, ASA5505 serving up DHCP for the network. Wired clients are receiving DHCP fine.
Mgmt IP
192.168.0.10/24
Mgmt Gateway
192.168.0.1
Mgmt VLAN
0
Mgmt Int port
1
Mgmt DHCP server
192.168.0.1
AP Mgr Int IP
192.168.0.11
Virtual GW IP
1.1.1.1
RF group name
rfgrp1
SSID
xxxx
Client Static IP?
no
Country Code
802.11a/b/g status
enabled
Radio resource mgmt status
enabled
I've run dhcpd debug on both the controller and the ASA and I see the DHCPD requests on the controller, but I never see them hitting the ASA.
I don't have the specific version of code it's running, but I know it's 6.0. One of my local Cisco account engineers found some Cisco CSC bugs referencing this issue. One TAC cas even referenced stripping all security off the WiFi, connecting the client and then reimplementing the security again.
Anyone have any suggestions? I'm hoping to head back over there again this afternoon to do some more troubleshooting and hopefully solve this for them.
Thanks!
Mike

In this case, the controller is not currently configured as DHCP server, although I may be trying that this afternoon.
I've currently got DHCP proxy enabled and am pointing it to the ASA5505 (192.168.0.1)- I thought I mentioned that in my previous post.
Please keep in mind this was working fine at one point in my lab while I was testing it, then I shut it down for a couple weeks while I waited to install it at the customer site. I've even tried resetting back to factory defaults and reconfiguring it to see if I'd accidentally misconfigured something.
I don't have the exact version, but I do know that I'm running a 6.x code rev. I'm probably going to just upgrade to 7.0 this afternoon and see if that makes a difference. If not, I'll try enabling the internal DHCP server, but I don't want to do that if I don't need to. Just one more thing to worry about managing for the customer.
Thanks,
Mike

Access Points Not Passing DHCP to Clients

I have a 50+ access point deployment, all in a single VLAN (DMZ), across a dozen buildings. We recently experienced wierdness of the following sort. Clients would request DHCP request, DHCP servers would forward requests, which would not get passed from the AP to the clients. We could verify that DHCP and all other parts of network were fine. I had to cold boot each AP to clear the condition. I could find nothing in this mix of 350s and 1200s or the spectrum that would indicate an obvious attack... Couldn't find where to start looking for any tables that were full, or any real place to look for some other reason for this. Yet after cold boot- all is well.
Any thoughts, in case it happens again?

Hi Guys,
I am having a similar problem to you, however i can get authentciated via LEAP, but dont seem to get an IP adderss from the radius server.
My setup is very simple as i am at the design stage. We have a Cisco AP 1200 (2.4 and 5.0 GHZ) and we are using FUNK steel belted RADIUS server. LEAP authentication works fine and i can see the association on the AP. The wirless client (HP W400 integrated Wireless cards) shows that it has been authenticated successfully too. However no IP is being received. We have a IP Pool configured on the SBR server and the SBR server shows that it has issued an IP address.
Next step was to place a sniffer and capture the packets. The capture shows the radius requests and challenges and in the very last ACCEPT packet we can see that the SBR has issued an IP address.
I am confused as i cant see anything on AP that would block the IP address. There are also a few attributes showing as "unknown" in the sniffer trace, so im not too sure wgats going on.
Can anyone help. The IOS is 12.2 (13) JA

New chat groups not showing up in client

i have skype installed on my mac and, apparently, I was added to a few new converstations. I am not seeing any of the messages in my client though. No new group popped up in the left hand bar. Individual conversations are still working and old chat groups that I have work, but not these new ones for some reason.
I logged into Skype on my iphone and I see the new chats there, so this is only on my mac client.
I restarted skype on my mac, logged out, logged back in, and even uninstalled and reinstalled, but no luck. The new group chats still don't show up.
Any ideas?

Can you confirm you are using the latest Skype 6.18 for Mac from www.skype.com/go/download
You can check your installed version from the menu "Skype - About".
Please report back which Mac hardware you are using should you have problems updating to 6.18
If you are already using 6.18: Please share the first 5 lines of output from issuing the following chat command in any chat. Just send this like any normal chat message:
/dumpmsnp
Follow the latest Skype Community News
↓ Did my reply answer your question? Accept it as a solution to help others, Thanks. ↓

Devices not showing up in client software Administration section

None of our devices are showing in the "devices" portion of the administration section in the client app.
Everything is functioning fine and I can administer devices through SysPrefs, but will eventually need to get back to this setup to add "edit in place" volumes, etc. I've tried refreshing, creating a new device to refresh list and many other things. I can't even search for a device by name in the "devices" section. Again, this is the only place where I can't see them.
Any ideas? Need it back bad!
Ryan

Hey!
Correct, not seeing any devices, but ONLY in the "devices" portion of the client admin. I see all my devices everywhere else and the entire system is functional, except for the fact that I can't get to them through the client admin. I can access it through the Sys Prefs portion of FCS, but need to get into the client admin for "edit in place", etc...
I do have backups from as far as 6 months ago, however - Much has changed on the server and I'd had to have to revert to one of those. Not sure exactly when this issue started, but I've seen it for at least a month.

Email sent from Nexus 4 not showing in Mail client

Going from an iPhone to an Android device has it's own issues, but one that shouldn't be an issue is that of IMAP emails.
In replying to any email from the Nexus 4, it will not be available to view in Apple's Mail client, which I use for all 5 of my email accounts. It will show in Mail that the email has been replied to with the arrow on the left of the email, but it will not allow me to click on the arrow to see the email I sent. It gives me an error message, 'Mail was unable to find your reply to the message "email subject title". You may have deleted the message'. Nope, I didn't delete the message, but now I can't see it. This is a very crucial missing element for business reply emails. My compnay uses GMail servers for all it's mail, so it's not a me.com email issue specifically. Funny enough, that email account set up the easiest. It doesn't show messages sent from the Nexus 4 either, but I'm sure it's all part of the same problem.
Is anyone else having this same/similar issue?
Thanks for the help, Bruce.

For Exchange GMail there is a way to set your iOS device to use a different "Send As" name than when using a computer. Unfortunately in your case, you can set your computer to send an alternate name but the iOS device can only send the default GMail name, which is the name associated with your account. Ideally, you would like your iOS device to use the alternate and let your computer use the default.
But if you want to play around with this ...
1- On the iOS device itself, use Safari to navigate to m.google.com/sync. You will have to log in at the prompt with your GMail account info.
2- Select the iOS device name (in case you have multiple iOS devices using Google sync).
3- Select "Enable 'Send Mail As' for this device" and Save the changes.
4- Using a computer, log into your GMail account and select Settings/ Accounts and Import, then at the "Send mail as" prompt select "edit info" (off to the right).
5- Change your outgoing name.
The name you specify in #5 will be used by your computer, but the iOS device will continue using the original (default) outgoing name. You can see why you need the opposite in your case, so unless you can change the default to be your wife's name and then set the alternate to be your name, I think you're out of luck.

Direct Reports not showing in Lync Clients for certain users in a pool

Hello guys, I am having issue with some users not being able to see direct reports of their managers in lync clients. Direct reports correctly shown in AD and outlook, but not in Lync. I have two paired lync pools. This issue is happening to users situated
within a pool. If I moved the manager to second pool, then users will see his direct reports. Does anyone knows how to fix this issue? Attached is sample.

Hi dareadepoju,
This information is from AD, you can try synchronizing the information manually.
Delete the .slabs file from the file share sitting on 000000000\000000000 folder and then run Update-CSUserDatabase and after 5 minutes, run Update-CsAddressBook.
The folder path:
X:\share\1-WebServices-1\ABfiles\000000000\000000000\
Best regards,
Eric

SCCM 2012 MOF changes not showing up on clients

Just updated my configuration.mof for getting a registry entry for a windows build rev. and it checked out well using MOFCOMP -CHECK Configuration.mof and then swapped it out with the live configuration.mof file. I then imported the reporting class
into SCCM HWInv GUI and it checked out fine. Dataloader created the tables/views in the SCCM DB and all seems well.
However, my clients are not picking up the HW inventory class updates and are not reporting in. Its been over a day so it shouldn't be replication. Where should I look to troubleshoot this?
Please help.
Thanks
Dave

Take a look at these two blogs. The first one is from the site server to the client. The second one is from the client to the site server.
http://be.enhansoft.com/post/2014/02/20/Inventory-Workflow-From-Client-Agent-Settingssms_defmofconfigurationmof-to-the-Client.aspx
http://be.enhansoft.com/post/2013/07/25/Troubleshooting-Inventory-Flow.aspx
http://www.enhansoft.com/

Cisco prime 2.1 not showing wired clients connected to Cisco 3850 switches

Hello All,
I have around 80 Cisco 3850 switches at a customer network and they are using prime infrastructure 2.1.2 to manage these devices. Most of the features are working fine except that the prime does not show the wired clients connected to the switches. The wireless clients are shown properly but not the wired clients. Their core switches are nexus 7k. The SNMP configuration on the switches is as follows.
snmp-server group xxxx v3 priv write xxxx-VIEW-WR
snmp-server view xxx-VIEW-WR mib-2 included
snmp-server trap-source Vlan100
snmp-server host x.x.x.x version 3 priv testuser
Please help me to resolve this issue.
Shabeeb

I managed to get the end hosts connected in 3850 switches with the use of snmp context command. But now the issue is that prime is showing only the mac address of the device , not the IP address.
Is there anyway to resolve this issue?

RV220W not showing DHCP Leased Clients (LAN)

Similar Messages

Maybe you are looking for