RV220W - Problems with Port 25 and SMTP
Hello. I'm really new to networking but I've been given the task of fixing a problem with our RV220W. Up until about two weeks ago our VOIP service would send our voicemails to our emails in a wav. file. But that's stopped completely when we came back last monday. I contacted our VOIP provider and they said they only send emails on port 25 and that our port must not be open anymore. (No network changes have taken place on our end)
So I did the following to open up port 25:
Then I
Still didn't work and they ran a diagnostic and got the following:
(10:42:30 AM) Liz: I restarted the postfix service and then tried to send a test:
(10:42:52 AM) Liz: Unfortunately, same timeout:
Oct 3 10:41:55 pbxtra6939 postfix/smtp[12538]: connect to ratsound.mail.pairserver.com[66.39.4.106]: Connection timed out (port 25)
Oct 3 10:41:55 pbxtra6939 postfix/smtp[12538]: AB9472EC010: to=<[email protected]>, relay=none, delay=30, status=deferred (connect to ratsound.mail.pairserver.com[66.39.4.106]: Connection timed out)
Our normal email service reported that they received no activity on there end and our ISP said they were not blocking port 25. So it must be something in the network settings right?
Any help would be appreciated as this is driving me bananas.
Thank You
Kea Kanamu
@indicter
Thank you for using HP support forum. I have sent you a private message. If you’re unsure how to check your private messages please click here.
Thank you,
Omar
I Work for HP
Similar Messages
-
HELP!! asa 5505 8.4(5) problem with port forwarding-smtp
Hi I am having a big problem with port forwarding on my asa. I am trying to forward smtp through the asa to my mail server.
my mail server ip is 10.0.0.2 and my outside interface is 80.80.80.80 , the ASA is setup with pppoe (I get internet access no problem and that seems fine)
When I run a trace i get "(ACL-Drop) - flow is deied by configured rule"
below is my config file , any help would be appreciated
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISPDsl
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_SMTP
host 10.0.0.2
access-list outside_access_in extended permit tcp any object server_SMTP eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network server_SMTP
nat (inside,outside) static interface service tcp smtp smtp
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c5570d7ddffd46c528a76e515e65f366
: endHi Jennifer
I have removed that nat line as suggested but still no joy.
here is my current config
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISP
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_Mail
host 10.0.0.2
access-list outside_access_in extended permit tcp any object Server_Mail eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network Server_Mail
nat (inside,outside) static interface service tcp smtp smtp
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f3bd954d1f9499595aab4f9da8c15795
: end
also here is the packet trace
and my acl
Thanks -
Problems with email and SMS after 1.3.5
Let me first say that I love the Pre. Up until this point it has been perfect - I have a replacement, but that is because I dropped it (wrong angle, wrong location, broken screen). However, following the 1.3.5 update I'm now having a fairly important problem with email and sms - I can receive email and messages, but not send them.
I have two email accounts. My personal account is with earthlink. My work account goes through an ISP using the domain name of my employer. I'm not using Microsoft Exchange or Outlook. I have tried deleting and reentering the accounts and that did not work. I can receive messages but get error messages when I try to send.
The same for messaging. I don't use it very often. But yesterday I get a text message and tried to respond and got the error message.
I power the phone off every night because I have a landline and use that as the primary phone at home.
I have been looking around message boards trying to find a fix for this. Has anyone had this issue and resolved it?
Thank you.
Post relates to: Pre p100eww (Sprint)
Message Edited by starburst42 on 01-05-2010 07:06 AM
This question was solved.
View Solution.I forgot to add that this is a stock Pre. There are no patches or homebrew apps.
Edit:
I found a fix for the email problem, in posts on precentral and this board from a few months ago. The info came up in a Google search, and not searches of the boards, which is kind of frustrating. Here is the info, and the link. I really wish Palm would put info about this work around on their site, or at least make it easy for people to find. The solution is the last message in the thread linked below:
Had the same problem. Checked with Earthlink - no help. Checked with Sprint - no help. Checked with Palm - no help. Here is what finally worked:
Delete the earthlink account and start over. When you do - this is the key - set up the account manually! If you use the Pre defaults and try to change the settings it will not correct the problem. Your settings for outgoing mail must be:
"smtpauth.earthlink.net"
Use Authentication set to "on"
username is your email address
your email password
port set to "587"
encryption "none"
Again, the key is to set up manually.
smtp email fix
Message Edited by starburst42 on 01-06-2010 12:08 PM
Message Edited by starburst42 on 01-06-2010 12:09 PM -
Problem with access to SMTP, IMAP, POP3 protocols in CAS 2013.
Hi,
we have problem with access thgrough SMTP, IMAP, POP3 protocols in CAS 2013.
If I test connection to SMTP 25 port from other computer, session end quickly.
Test from CAS2013 to localhost or public IP is OK (similar also for IMAP and POP3).
Receive connectors are with defaults settings, firewall is disabled.
Service Microsoft Frontend Transport Services restarted, but no success.
Certificate is assigned to IMAP, POP3, SMTP, IIS.
IIS and HTTP(s), protocols are OK. Clients can connects only thgrough web, mobile (ActiveSync), or with Outlook with proxy.
Do you have some tip, what to test?
If I create new testing receive connector on port 26 for anonymous, behaviour is same, quick disconnecting.
Thank's MirekHi,
Pleaser try to use the following link to test your STMP/POP/IMAP e-mail, and check the test if successful:
https://testconnectivity.microsoft.com/
If unsuccessful, please check the test result, it will tell us what caused the problem.
Thanks.
Niko Cheng
TechNet Community Support -
Having problems with OSX and mail with the servers?
Having problems with OSX and the mail servers? Seems to be happening more and more?
Hello,
Who is your eMail provider, the part after the @ sign?
In Mail's Window Menu, choose Connection Doctor, any red dots for status, if so what is the message?
Then click the Show Details button & Check again.
Open Keychain Access in Utilities, use Keychain First Aid under the Keychain Menu item, then either check the Password under that item, change it, or delete it and start over.
You may have multiple entries.
Open Keychain Access in Utilities, enter the part after the @ sign in the search bar, hit enter
The Password rejection can confuse people since it's a catch all meaning...
This Password, Username, Authentication method... is not recognized on this Port to this Server, more than one entry in Keychain for each in/out entry, or a server end problem.
If using a browser to login via WebMail works it's not Name or Password, but one of the other ones.
The receiving email ports are:
IMAP is port 143
IMAP-SSL is port 993
POP is port 110
POP-SSL is port 995
Outgoing ports are...
SMTP and SMTP-SSL is on ports 25, 587 and 465. Port 587 has to be SSL, and port 465 is enforced TLS-wrapped and is generally used by Outlook users. -
Problem with Send and Receive Emal In SAP System
Hi gurus!
I have a following quote:
Dear !
I have a problem with send and receive email in SAP system following :
I want to test send and receive email in local network at my company. I
had two server
Server 1 : I setup Exchange Mail Server 2007 with domain controller is
fes.com
Server 2 : I setup SAP ERP ECC 6.0
On Server 1 : I created 2 account ( u1Afes.com and u2Afes.com ) and then I tested send and receive email between u1 and u2 in local network through Microsoft Outlook 2007 -> OK
and then
On Server 2: I had configured send and receive email on SAP system
through tcode SBWP, SCOT and SOST as Note 455140 - "Configuration of
e-mail, fax, paging or SMS using SMTP"
for example :
I logged in SAP system with user Basis01 (with email u1Afes.com ) -> then,using tcode SBWP -> new message -> send to u2Afes.com with Internet Mail type and then status message with green light -> sending ok
and then I have used Microsoft Outlook 2007, I logged with account u2 ->check email -> Ok. I saw message which send from u1
Finally, My problem is how can receive mail in SAP system without using Microsoft Outlook
For example:
Login system SAP with Basis01 account (with u1Afes.com ) -> tcode SBWP ->New Message -> send to u2Afes.com
and then
Login system SAP with Basis02 account (with u2Afes.com ) -> tcode ??? ->
To receive email from Basis01 (with u1Afes.com )
Please help me now
Thanks
I replace "@" with "A" because of banning email of this forum.
This quote is about sending email in local network. And we can't receive any email from the outside email address. Addition if I wanna send email to internal email in Internet (we've just tried with email address in local network) What should I config in SAP and Exchange ?
By the way, Is SAP Server IP added to Relay Agent for sending or receiving mail ?
Regards
An NLP
Edited by: An NLP on Apr 6, 2010 7:03 PMHi,
This problem is a classic problem of mail routing via Exchange. Exchange like most mail servers use the domain part of the email address as a means to route mails. So I will make an assumption that your main company mail addrss is "User @ fes.com".
So when you send a mail to the "User @ fes.com mail" address the mail is delivered to your Outlook mail address as this is the default route for company.
(Q) So how do you get your Exchange server to relay the mail into the sending SAP system?
(A) The easiest way would be to setup and unique mail domain for your SAP system. I always recommend "user @ client.sid.company.com" which in your case would be "u1 @ 100.PRD.fes.com". You can then instruct Exchange to send any emails addressed to 100.PRD.fes.com domain to your SAP system. Also using this format of address you can configure multiple mail connections into multiple SAP systems.
(A) Another answer would be to enter the "Full" email address (LOcal and Domain part of address) into the routing rule for Exchange e.g. "U1 @ fes.com" so that all emails addressed to this user will be delivered into SAP. However this method requires a lot of Admin as you will have to update Exchange with ALL email address that need to receive emails. Also if your corporate mail address is "U1 @ fes.com" then all mails will be forwarded to SAP.
I would definitely NOT recommend this method but the decision is up to you.
P.S. The IP address of the SAP system is entered into the mail header of the email. This is standard practice in SMTP relay. You can suppress this header in Exchange
Hope this helps
Michael -
Problem with connecting and syncing (quicktime.qts)
Hi,
I have a problem with connecting and syncing my Iphone to itunes.
iphone alone on PC -> uploading files (fotos) is possible
itunes starts normaly, if iphone is not conected.
if i connect iphone after starting itunes, or if i start itunes after connecting iphone i get an itunes-error with message:
AppName: itunes.exe AppVer: 9.0.2.25 ModName: quicktime.qts
ModVer: 7.65.17.80 Offset: 00909a47
i test different things...
- used another USB-port
- used another PC
- used macbook of my wife instead PC
- deinstalled and new installed of itunes (older and newer versions) folow tutorials of apple
- use another USB-Cable...
I'm resigned, Please help me..
TomAppName: itunes.exe AppVer: 9.0.2.25 ModName: quicktime.qts
In this context, that can sometimes indicate trouble with a content file on the phone (or Touch).
Do you have any podcasts stored on the iPhone at the moment? If so, if you delete them from the phone, can you connect to iTunes without the error? -
Hi *,
I have the following problem with RADIUS and EAP authentication.
Radius server sends an "Access-Accept" packet to my AP, but the station does not authenticate.
I've tried with different encryption configuration and with different authentication methods under "dot11 essid", but nothing changes...
What could it be?
Debug piece and configuration follows:
*Jan 25 14:23:34.795: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.795: RADIUS(00000012): sending*Jan 25 14:23:34.799: RADIUS: 4E 47 56 7A 78 65 4A 4F 55 31 47 40 77 6C 61 6E [NGVzxeJOU1G@wlan]*Jan 25 14:23:34.799: RADIUS: 2E 6D 6E 63 30 30 31 2E 6D 63 63 30 30 31 2E 33 [.mnc001.mcc001.3]*Jan 25 14:23:34.799: RADIUS: 67 70 70 6E 65 74 77 6F 72 6B 2E 6F 72 67 [gppnetwork.org]*Jan 25 14:23:34.799: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.799: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.799: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.799: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:34.811: RADIUS/DECODE: EAP-Message fragments, 20, total 20 bytes*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:34.831: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:34.831: RADIUS: 32 [2]*Jan 25 14:23:34.831: RADIUS(00000012): Config NAS IP: 192.168.173.2*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.835: RADIUS(00000012): sending*Jan 25 14:23:34.835: RADIUS: 10 01 00 01 07 05 00 00 D9 37 C3 D9 79 3E 33 EA [?????????7??y>3?]*Jan 25 14:23:34.835: RADIUS: F3 7D 73 43 BF BA D0 6A [?}sC???j]*Jan 25 14:23:34.835: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.835: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.835: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.835: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.035: RADIUS: Received from id 1645/64 192.168.177.158:1812, Access-Challenge, len 304*Jan 25 14:23:35.039: RADIUS: 46 10 78 5F 5F B0 CB 6C 0B 05 00 00 DA C3 BF 28 [F?x__??l???????(]*Jan 25 14:23:35.039: RADIUS: E0 18 2B 95 97 C2 0A D7 40 53 FE 62 [??+?????@S?b]*Jan 25 14:23:35.039: RADIUS(00000012): Received from id 1645/64*Jan 25 14:23:35.039: RADIUS/DECODE: EAP-Message fragments, 60+220, total 280 bytes*Jan 25 14:23:35.355: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:35.359: RADIUS: 92 DA 5E 26 CF 40 01 22 7A 8E F5 C1 [??^&?@?"z???]*Jan 25 14:23:35.359: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:35.359: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:35.359: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:35.359: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.367: RADIUS: Received from id 1645/65 192.168.177.158:1812, Access-Accept, len 30*Jan 25 14:23:35.367: RADIUS: authenticator 8C 2C 1B 97 82 BB 6C 7F - AA D3 4A AB CA 22 8B B7*Jan 25 14:23:35.367: RADIUS: EAP-Message [79] 10 *Jan 25 14:23:35.367: RADIUS: 03 01 00 04 00 00 00 00 [????????]*Jan 25 14:23:35.371: RADIUS(00000012): Received from id 1645/65*Jan 25 14:23:35.371: RADIUS/DECODE: EAP-Message fragments, 8, total 8 bytes*Jan 25 14:23:35.671: %DOT11-7-AUTH_FAILED: Station d023.dbb8.d6a9 Authentication failed
Config:
aaa new-model!aaa group server radius rad_eap server-private 192.168.177.158 auth-port 1812 acct-port 1813 key 7 044803071D2448!aaa authentication login eap_methods group rad_eapaaa authorization exec default if-authenticated aaa authorization network default if-authenticated ! aaa session-id commonip name-server 192.168.177.45! dot11 ssid WifiEAP1 vlan 10 authentication open eap eap_methods authentication shared eap eap_methods authentication key-management wpa optional guest-mode! bridge irb! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 10 mode ciphers aes-ccm tkip wep128 ! broadcast-key vlan 10 change 300 ! ssid WifiEAP1 ! antenna gain 0 station-role root! interface Dot11Radio0.10 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled! interface GigabitEthernet0 ip address 192.168.173.3 255.255.255.0 no ip route-cache! interface GigabitEthernet0.1 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled! interface BVI1 ip address 192.168.173.2 255.255.255.0 no ip route-cache!ip radius source-interface BVI1 bridge 1 route ip
thanks so much!Stefano: not sure if related but there is an unsupported attribute in the debugs:
Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr:
*Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41
*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface
Try to eliminate any configured attributes on radius except those in IETF radius. Then try again.
You may also chech by removing the shared eap as suggested above. Let us know if this works.
Sent from Cisco Technical Support iPad App -
Link Problem with port 2 in WLC 4402
Hi,
I have a problem with port 2 in Wireless Lan Controler 4402. The problem is that the distribution port 2 of the WLC not link with the switch (3750). We receive the WLC and we follow the autostart wizard and we enable LAG. The wizard finish, I restart the system and all works fine. The two distribution ports of WLC, 1 and 2 appears UP and the LAG works correctly. After this we upgrade the firmware of the WLC to the version AIR-WLC4400-k9-6-0-182-0.aes and we restart the system again but at this time port 2 does not link and port 1 link OK. We do not know the reason why port 2 doesn´t link? Could you help me ?
Thank in advance.
Regards.Does it properly refuse authentication ? Or does the login page stop appearing or something ?
There was a bug with the webauth dying under heavy load, regardless of number of identical accounts used.
One good way for you to check would be, when problem occurs, to create a second backup guest user and see if that would start working. If it doesn't, the account is not the problem.
I'm not aware of any maximum of usage of the same account.
Which 4.2 exactly are you running ? -
Problem with Port Forwarding in WRT320N
Good day.
I have a web-server and Internet-radio translator to local network of my provider. And I found a problem with Port Forwarding. I'm trying to setup 80 & 8000 ports to forward. And it's working but only for Internet, without provider's local network. My web-server isn't accessible in local network and radio-translator too.
So is it possible to forward ports absolutely - for any type of connections?
P.S. DMZ is working like Port Forwarding.If you ask questions you have to mention that you have an PPTP connection to the internet and another network directly on the internet port. Otherwise noone will really understand your question as it is a very unusual setup.
Your setup is not one really supported by the router. You are lucky that it works but don't expect too much. Port forwarding only the internet connection. If you use PPTP the network on the internet port is basically hidden. Using that local network on the internet port is not supported.
The DMZ host is the IP address to which all ports are forwarded to which are not forwarded otherwise. The same restriction applies here.
I would recommend to ask your ISP which router they recommend for their internet connection. I think most/all Linksys routers and many other brand's consumer routers won't really support a setup like yours... -
Problem with JFrame and busy/wait Cursor
Hi -- I'm trying to set a JFrame's cursor to be the busy cursor,
for the duration of some operation (usually just a few seconds).
I can get it to work in some situations, but not others.
Timing does seem to be an issue.
There are thousands of posts on the BugParade, but
in general Sun indicates this is not a bug. I just need
a work-around.
I've written a test program below to demonstrate the problem.
I have the problem on Solaris, running with both J2SE 1.3 and 1.4.
I have not tested on Windows yet.
When you run the following code, three JFrames will be opened,
each with the same 5 buttons. The first "F1" listens to its own
buttons, and works fine. The other two (F2 and F3) listen
to each other's buttons.
The "BUSY" button simply sets the cursor on its listener
to the busy cursor. The "DONE" button sets it to the
default cursor. These work fine.
The "SLEEP" button sets the cursor, sleeps for 3 seconds,
and sets it back. This does not work.
The "INVOKE LATER" button does the same thing,
except is uses invokeLater to sleep and set the
cursor back. This also does not work.
The "DELAY" button sleeps for 3 seconds (giving you
time to move the mouse into the other (listerner's)
window, and then it behaves just like the "SLEEP"
button. This works.
Any ideas would be appreciated, thanks.
-J
import java.awt.BorderLayout;
import java.awt.Cursor;
import java.awt.event.ActionEvent;
import java.awt.event.ActionListener;
import javax.swing.JButton;
import javax.swing.JFrame;
import javax.swing.JPanel;
import javax.swing.SwingUtilities;
public class BusyFrameTest implements ActionListener
private static Cursor busy = Cursor.getPredefinedCursor (Cursor.WAIT_CURSOR);
private static Cursor done = Cursor.getDefaultCursor();
JFrame frame;
JButton[] buttons;
public BusyFrameTest (String title)
frame = new JFrame (title);
buttons = new JButton[5];
buttons[0] = new JButton ("BUSY");
buttons[1] = new JButton ("DONE");
buttons[2] = new JButton ("SLEEP");
buttons[3] = new JButton ("INVOKE LATER");
buttons[4] = new JButton ("DELAY");
JPanel buttonPanel = new JPanel();
for (int i = 0; i < buttons.length; i++)
buttonPanel.add (buttons);
frame.getContentPane().add (buttonPanel);
frame.pack();
frame.setVisible (true);
public void addListeners (ActionListener listener)
for (int i = 0; i < buttons.length; i++)
buttons[i].addActionListener (listener);
public void actionPerformed (ActionEvent e)
System.out.print (frame.getTitle() + ": " + e.getActionCommand());
if (e.getActionCommand().equals ("BUSY"))
frame.setCursor (busy);
else if (e.getActionCommand().equals ("DONE"))
frame.setCursor (done);
else if (e.getActionCommand().equals ("SLEEP"))
frame.setCursor (busy);
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.print (" finished");
else if (e.getActionCommand().equals ("INVOKE LATER"))
frame.setCursor (busy);
SwingUtilities.invokeLater (thread);
else if (e.getActionCommand().equals ("DELAY"))
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (busy);
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.print (" finished");
System.out.println();
Runnable thread = new Runnable()
public void run()
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.println (" finished");
public static void main (String[] args)
BusyFrameTest f1 = new BusyFrameTest ("F1");
f1.addListeners (f1);
BusyFrameTest f2 = new BusyFrameTest ("F2");
BusyFrameTest f3 = new BusyFrameTest ("F3");
f2.addListeners (f3); // 2 listens to 3
f3.addListeners (f2); // 3 listens to 2I've had the same problems with cursors and repaints in a swing application, and I was thinking of if I could use invokeLater, but I never got that far with it.
I still believe you would need a thread for the time consuming task, and that invokeLater is something you only need to use in a thread different from the event thread. -
Problem with installing and running some applications or drivers
When installing and installing some items, towards the end of the installation I get this message:
/System/Library/Extensions/comcy_driver_USBDevice.kext
*was installed improperly and cannot be used. Please try reinstalling it or contact product's vendor for update*
The end result is that some things do not seem to work properly, such as my HP printer. Would anybody have any ideas on how to fix this problem?Thank you for your response. Originally, I had a problem with Airport and ended up reinstalling Snow Leopard. Since then, when downloading upgrades etc, such as HP printer drivers, iTunes etc., towards the end of the download when its running the script, I get this message: /System/Library/Extensions/comcy_driver_USBDevice.kext
+was installed improperly and cannot be used. Please try reinstalling it or contact product's vendor for update+
Sometimes, the download hangs and is unable to complete. The main problem I've encountered so far with an application is when I use the printer to scan an image via Preview, it's blank: there's nothing there. -
Problems with outlook and address book contacts: my outlook contacts had around 3,000 entries. Outlook duplicated entries and have now 340,000. I reinstalled microsoft office and, thus, outlook, and reinstalled mac OS X system and applications. While I managed to delete outlook contacts so that I can re-sync with my blackberry, the contacts at Mac Address Book were not deleted and still have over 340,000 entries. I do not mind deleting all contacts since I have back up, but I have not been able to delete them. Also, when I go at Address Book and try to delete or merge duplicated entries, the system takes forever and never ends because of such large amount of entries. Worse, when I do so I run out of RAM memory.
My Macbook pro is just 2 months old.
What should I do? Is there a way to delete my Mac Address Book without having the problem above?
Many thanks
Regiszlatan24 wrote:
For solving out troubles connected with corrupted or lost address book you may use address book recovery. It owns various features such as restoring wab files, it working under any Windows OS. The utility has modern and easy to use interface due to almost every experienced users.
If it is a windows problem it's not going to run on the OP's MacBook Pro -
Problems with Safari and Firefox (HTTP?)
Problems with Safari and Firefox (HTTP?)
On a laptop G4, 10.5.8 and Safari 5.02 I experience the following:
On the account of my oldest daughter everything works fine, i.e. wireless internet works and no problems with mail or safari.
On the same laptop, on the account of my other daughter, the wireless is OK, she can mail etc. But safari nor firefox works. It says: can’t find server (whatever site) and in the activity window it looks if safari tries to open files (in the safari preferences-folder) in stead of http. Same applies to Firefox, so maybe it has more to do with HTTP in general?
What goes wrong? What to do? I tried the following on the host terminal (tips from Apple)
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false
and
defaults delete com.apple.safari WebKitDNSPrefetchingEnabled
but that did not help,
NanneI'm still wondering why it happens now at this moment in time...
PC does seem to be a bit odd & inconsistent, the few times I've tested with it, at least so far as we content filtering goes; and if I remember rightly, you're not the first to report previously ok settings suddenly preventing some or all internet until pc is switched off altogether.
It may work when re-enabled -
Haven't been able to use pages for a while. Keep getting following message. Have tried reinstalling iWork, but no luck. Same problems with Keynote and Numbers/
Have you moved Pages from its installed location? Or just dragged a copy to your current system?
It can't find some of its resources apparently.
Peter
Maybe you are looking for
-
I multiple ipods (3 different users) on the same itunes account. All of the music is either from cd's or purchased from iTunes legally. A new iPod has been purchased, and I want to open a new iTunes account for the daughter so I can actually use iClo
-
How can I reload itunes on my iPhone 5?
After updating my iPhone, the iTunes app has no content. I can search and search suggestions drop down from the search field but when clicked on, yield no content at all. Click on Music, TV, Movies... nothing populates. Can't buy music. Thanks. Jeff
-
Lenovo S820 problem in call with bluetooth headset
Hello All. I have Lenovo S820. I update smartphone to last version firmware. Information from phone: Model: Lenovo S820_ROW Android system version: 4.2.1 Firmware communication module: S820.V21, 2013/08/07 15:14 Build number: S820_ROW_S119_130922 I a
-
New Windows 8.1 computer will not recognize HP Photosmart 6525 Printer.
My father in law got a new computer that has Windows 8.0 and we upgraded it to 8.1. I cannot get the computer to recognize the printer. I have downloaded the drivers and also tried to use the cd that came with the printer. While installing I get the
-
I receive the message: "The extension could not be loaded because it was not properly signed."
When I try to open the Library in Photoshop, I receive the message: "The extension could not be loaded because it was not properly signed." It worked last week, but now I get this message and the Library is completely empty in Illustrator. My Library