RV220W VPN Monitoring

Hi all, I was wondering if there is a way to configuring monitoring on a IPSEC site-to-site VPN. I only need the basics such as status and maybe response times. Is there any way to implement this with functionality on the router or do I need to find another tool to do so?
Thanks,
Andrew

Hi Ken,
I tested a free syslog server software with a WRV210 router some time ago. If I recall correctly all URLs that I visited were collected by that server. I think the software was from Solarwinds and it was running on Windows XP.

Similar Messages

"Polling not started" on VPN Monitor Dashboard

I always get the message "Polling not started" on VPN Monitor Dashboard for the Pix firewall device I have in my list.
Is there any way to trigger polling ?
Thank you for your help.

One possible reason : wrong community string etc. By default, it should run every five minutes

RV220W, VPN client, and Full Tunnel vs Split Tunnel capabilities

For an RV220W, which VPN client mode (of the three possibilities) supports which Tunnel mode?
This is mostly a question, and partly "in use" observations.
Background: I have been able to get all three different VPN clients to work with an RV220W, but only one of the three works in "Full Tunnel" mode (SSL VPN). And since I know one of the three -- the Cisco QuickVPN client -- will never with in that mode, do we know if an RV220W will with an IPSec client in Full Tunnel Mode?
If anyone answers yes, the next question will be vpn client and how did you configure it, client and RV220W, to make full tunnel work.
Summary of VPN modes I've gotten to work with an RV220W:
Client
Split Tunnel Works?
Full Tunnel Works?
OS?
Notes
SSL VPN
Yes
Yes
Win7/64
IE10 or IE11
QuickVPN
Yes
No
Win7/64
IPSec VPN
Yes
No
Win7/64
Shrew Soft VPN Client

I have to mark this as not a correct answer.
Reason: 0.0.0.0 will not go into either of the fields listed above, message is "Invalid IP address Please enter a value between 1 - 223 at xxx.0.0.0.".
To Michal Bruncko who posted this:
1.) 0.0.0.0 will not work in my router nor in the RV220W online emulator here, (general emulator page here), am I missing something obvious?
2.) Have you used these actual settings on your router, or did you answer in a theoretical, "this should work" way?

RV220w VPN firmware 1.0.6.6

have an ip address than end in zero from isp the VPN set up menu will not allow you to put a zero in the last octet.
2015-03-05 07:14:32: [rv220w][IKE] ERROR: Could not find configuration for 71.3.174.0[500]

2015-03-09 08:32:00: [rv220w][IKE] INFO: Responding to new phase 2 negotiation: 192.168.250.148[0]<=>71.3.174.0[0]
2015-03-09 08:32:00: [rv220w][IKE] INFO: Using IPsec SA configuration: 10.10.100.0/24<->10.10.20.0/24
2015-03-09 08:32:00: [rv220w][IKE] ERROR: Not supported nested SA. Peer IP 184.106.55.77[0] does not match SA End Point
2015-03-09 08:32:00: [rv220w][IKE] ERROR: failed to create saprop.
2015-03-09 08:32:00: [rv220w][IKE] ERROR: Failed to get proposal for responder.
the 10.10.20.0/24 is from the ip 71.3.174.0 and the configure page will not let you put in that address:

Which RV220W VPN-setup do I choose in the following situation?

My RV220W has a fixed IP-address on its WAN and there is an ISP-provided FQDN with reverse lookup available. Is it possible to setup an IPsec VPN on this box that a Mac laptop can connect to the VPN from any location world wide that does not actively block VN traffic in some way?
I know a PPTP connection to the server on my LAN works, but I'd rather have an IPsec connection to the RV220W and turn the PPTP server on the host inside my LAN off.
If this is possible, what do I enter where in the wizard?
I have been unable to get this from the manual or by trying to find a recipe somewhere on the net,

It explains how to set up the RV220w for IPSec, and connecting using free IPSec clients on both Windows and MacOS.
https://drive.google.com/file/d/0B0EERf9TN4v1Ym9uaWRlMXhfVGM/edit?usp=sharing

RV220W - VPN PPP & RDP problem

Hello!
This is my first post here, so welcome!
I have purchased RV220W router and implemented into the existing netowork. Everything seems to work fine except logging into rdp desktops of wxp's on the local network in the office.
I'm not using router's VPN capabilities. I have made a connection through one of the WXP's VPN locally in the office. I login with password as PPP connection. Everything works fine, but I can only connect through RDP to the machine that is making the connection by "VPN IP". I cannot login to any IP that is local in the office. I can not ping either.
We are using also Macs and the same problem is when connecting with ScreenSharing and pinging.
It is definitely something to be set on the router.
If you have any idea, I would apprecite your help!

Hi again!
After reading similar post I found a "solution".
I have manually put actual RV220W IP as router ip (except of the ip of the XP that is making the vpn connection) on the computer I'm connected to VPN and now it's working fine.
Anyway, thanks for approving this thread.
Cheers,
Adam

RV220W VPN

Ugh. I've spent endless hours trying to get the VPN to work. I've done all the recommended actions for QuickVPN (run as Vista SP2, disable avast, enable windows firewall, disable windows defender, create windows ICMPv4 rules, turned on IPSEC services, disabled other network adapters) but I can NEVER connect. It always comes up with waiting for network.
I set up PPTP today. And it worked partially. I was able to access the RV220W but unable to browse any other networked devices or even access the internet. I ran the windows diagnostic tool and it said it was a DNS issue on the remote side.
Can someone please guide me before I end up ripping this device off the network? Much appreciated!

Troy,
What is your OS?
Does the RV220W have a static WAN IP?
Who is the ISP?
Where are you connecting FROM?
Does the local router have a different IP than the RV2220W?
Is the RV220W on the latest firmware?
- Marty

RV220W VPN Setup

I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
Does any one have a simple step by step guide to this?
Many Thanks

Tom's right. The only Cisco Small Business class routers that support the Cisco 5.x client are the SA500 Series routers. I don't see them changing that because the Cisco 5.x client is nearing end of support. If anything they would add Cisco AnyConnect support. That's the latest, greatest VPN tech from Cisco.
We can help you setup SSL VPN (for Windows and/or Mac OSX Snow Leopard) and/or IPSec VPN (using IPSecuritas for Mac OSX and/or Shrewsoft/Quick VPN/Greenbow for Windows). You have lots of options to get VPN access to your RV220W. The RV220W even supports PPTP VPN which works with the Apple iPhone, iPad, etc.

VPN monitoring

Hi, i have a IPSEC VPN tunnel on a 7206 router. Concern is that we want to monitor the status of the tunnel, with following points...
- Other end is not willing to give us the ICMP access, so we cannot check the status using ICMP.
- We have enabled the tunnel on CiscoWorks VPN/Security Monitoring Solution.
First requirement: is that we want to give an interface to our 24/7 helpdesk team, with limited rights.. when i create a user id on CW, with privilege access=helpdesk,that id can view other devices as well, which is not desired. We JUST want to give the page of VPN monitring to that team. How can that be achieved?
Second Requirement: We have a solution where we can send any text file to our mobile thru sms. I want to send the syslog thru that router-->CW--> our mobile. I can see that the syslogs are reaching in CW-->RME-->Syslog Analysis, but i get following message when i go to CW-->VMS-->Syslog analysis,i get "No records found"..
so, the first thing is to get the syslog messages visible in VMS, and the second thing to do is to get those syslogs sent to a text file on the server, and rest is easy.
Please help on both of requirements.

is there no one else?

RV220W VPN setup for iPad

How to step a IPSec connection for iPad with this Firewall appliance?
Thank you in advance for your help...

1)check that Local LAN (Local Network) IP Address number shows actually a NET address and not a host address, if it is a 192.168.1.1 /24 then, the value should be 192.168.1.0
2)make sure that 'Block WAN Request' is disable
3)disable PFS
4)delete the VPN configuration and re-do it againg and reboot te router to make sure that old configuration has been deleted.
5)Check Firewall settings "depending on the operating system"
6)Try to create another VPN to a different location from the one giving the issues to make sure the issue is not related to this specific location

Connecting an iPhone/iPad to RV220W's VPN

Hi
I am looking to purchase the RV220W router. I am interested to know if I can use the iPhone/iPad to create a VPN connection to this router.
I have seen a lot of conflicting information about this so I am looking for a confirmation .
Thanks,
Alex

Hello,
Just to people with the same challange:
I can confirm that it´s possible to connect with iOS (iPhone 4S iOS Version 6.0.1) to RV220W (Firmware 1.0.4.17)
Steps on RV220W:
     1) Enable Remote Mangement (Administration-->Remotemanagement-->Remotemanagment enable
     2) Activate PPTP Server on RV220W (VPN-->IPSec-->VPN Users)
     3) Create User for PPTP Access (VPN-->IPSec-->VPN Users) Protocoll: "PPTP"
Steps on iPhone
     1) Create new VPN Connection (Setting-->General-->VPN--> Add VPN Configuration
     2) Choose "PPTP"
          as "tekliu" above mentioned:
          RSA SecureID:OFF
          Encryption Level: AUTO
          Send All Traffic: ON
          Proxy: OFF

Border Manager 3.8.5 and S2S VPN

I have a couple of questions with Border Manager and S2S VPN. Everything
is up and running, we can ping both servers (Netware 6.5.6), we can ping
workstations attached to each others network, we can access programs from
each others network. Everything seems to be working great. The question I
have is this - on both servers, under Remote Manager, VPN Monitoring, both
show as 'Being Configured'. I do not think that this is an issue but there
is another error in the Audit Log. The error -
"Proposal Mismatch - Quick Mode: ESP - transform mismatch mine: esp des
his: esp 3des dst: xx.xx.xx.xx src: xx.xx.xx.xx cookies
my-his:17B2D88772DE1D61 - 4F15FFD50824F821".
This appears on both servers Audit Log.
Is this a legit error or a information error? I used Craig Johnson's 'A
Beginner's Guide To BorderManager 3.x' but ended up making both VPN's
masters as per Novell TID - 10095268.
If anyone has an insight as to what these errors are and if there is a
fix it would be greatly appreciated.
Kelly

Kelly Burnside wrote:
> I have a couple of questions with Border Manager and S2S VPN. Everything
> is up and running, we can ping both servers (Netware 6.5.6), we can ping
> workstations attached to each others network, we can access programs
> from each others network. Everything seems to be working great. The
> question I have is this - on both servers, under Remote Manager, VPN
> Monitoring, both show as 'Being Configured'.
Sometimes the imanager snapin can not get the current status of the
connection from vpinf so it shows 'Being Configured'. It can take some
times, maybe days to change the status.
I do not think that this is
> an issue but there is another error in the Audit Log. The error -
> "Proposal Mismatch - Quick Mode: ESP - transform mismatch mine: esp des
> his: esp 3des dst: xx.xx.xx.xx src: xx.xx.xx.xx cookies
> my-his:17B2D88772DE1D61 - 4F15FFD50824F821".
This is not an error, it is an information message.
> This appears on both servers Audit Log. Is this a legit error or a
> information error? I used Craig Johnson's 'A Beginner's Guide To
> BorderManager 3.x' but ended up making both VPN's masters as per Novell
> TID - 10095268. If anyone has an insight as to what these errors are
> and if there is a fix it would be greatly appreciated.
> Kelly
Everything is fine, nothing to be worry about.
gonzalo

Help in setting up VPN for Remote Desktop

Hi,
We recently purchased a Cisco RV220W VPN Router and want to set up VPN connections for about 10 users(employess) to connect to their work PCs (mostly win 7 & win 8) from their home computers (windows & mac) using Remote Desktop. The documentation is quite poor. Can anyone point me to a tutorial and/or help me out with steps and settings? From the Admin Guide, it looks like I should be configuring Remote Access with an IPsec Client, but it's not clear how to handle/route multiple machines?

Hi Ray,
You can use the QuickVPN client to connect up to Windows 7 PCs. Windows 8 is not supported as of yet.
For Windows 8 and Mac you can create PPTP users or try a third party VPN client like Shrewsoft (Windows) or IPSecuritas (Mac). You also have the SSL VPN option in the RV220W. Please note that the third party clients are not officially supported by Cisco.
There are some good instructions for setting up Shrewsoft with the SA500 which is similar to the RV220W here:
https://supportforums.cisco.com/docs/DOC-9378#comment-7216
IPSecuritas for Mac:
http://www.cisco.com/en/US/docs/security/multi_function_security/multi_function_security_appliance/sa_500/technote/note/SA500_mac_appnote.pdf
Please reply if you have any questions.
- Marty

MAC OS X Clientless VPN Plug-in Installation Problem Solved

I have nearly pulled my hair out trying to get clientless VPN connections to work for Mac users looking to connect into our RV220W.
The key is to connect to the router as root the first time in order to avoid VPN plug-in installation permissions issues.
Preconditions: Java must be installed. Installing Java 7 for Mac OS X is 64-bit. This means that 32-bit browsers like Chrome cannot be used and that only 64-bit browsers like Safari will work with the plug-in.
Part 1 – Install the VPN Plug-in
Enable the root user account.
Log into the Mac as root.
Connect to the RV220W VPN portal.
Enter your credentials.
Select VPN Tunnel menu item
Hit the SSL VPN Tunnel Client Installer / Launcher icon.
When prompted, run the Installer.
The VPN should connect.
Disconnect from the VPN and log out of the root System Administrator account.
Part 2 – Use the VPN Plug-in
Log in as your normal user account.
Connect to the router’s VPN portal.
Enter your credentials.
Select VPN Tunnel menu item
Hit the SSL VPN Tunnel Client Installer / Launcher icon.
When prompted, run the software.
The VPN should connect.

I solved my problem by downloading and installing the "Final Cut Pro Universal (supports Intel)" .sit version of the plug-in, which is not the default. I will inform StageTools that the default .zip download doesn't seem to work.

BM 3.8 S2S with prosafe vpn firewall fvs124g

Hi,
Had a solid tunnel setup and then it dropped:
WED JUL 14 13:40:03 2010 INFO :: Quick Mode completed with message ID(0x506f7528)
WED JUL 14 15:28:26 2010 INFO :: Initiator SPD selectors received: IP SUBNET, 10.30.0.0, mask 16 proto 0, port 0
WED JUL 14 15:28:26 2010 INFO :: Responder SPD selectors received: IP SUBNET, 10.31.1.0, mask 24 proto 0, port 0
WED JUL 14 15:28:26 2010 INFO :: IKE phase-II Started with message ID (0x619afefb)
WED JUL 14 15:28:26 2010 INFO :: Initiator SPD selectors received: IP SUBNET, 10.30.0.0, mask 16 proto 0, port 0
WED JUL 14 15:28:26 2010 INFO :: Responder SPD selectors received: IP SUBNET, 10.31.1.0, mask 24 proto 0, port 0
WED JUL 14 15:28:26 2010 INFO :: IKE phase-II Started with message ID (0xfab7216)
WED JUL 14 15:28:26 2010 INFO :: Deleting the IsakmpSA.
Checking the Netgear VPN status it showed phase 1 as idle and phases 2 as connected. Checking Novell Remote Manager VPN monitoring it also showed the connection as up. I have them both setup as intiate and respond. Is there a way I can get them to recognize the connection dropped and re-setup? To get them going I had to drop and reload IKE on the BM server.
Thanks,
Will

Will,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

RV220W VPN Monitoring

Similar Messages

Maybe you are looking for