RV320 and Shrew Soft vpn client - cannot get it to connect

Hi,
I have been trying to configure Shrew vpn client 2.2.2 to connect to the RV320 but i cant even get phase1 to work. I would be very grateful is someone has managed this and could post the configuration (tunnel, groupvpn or easyvpn). I use:
RV320 with fw 1.1.1.19
Windows 8.1 Pro x64
Shrew Soft vpn-client 2.2.2

Okay here you go please see attached images.
Please note the following:
In this example NAT Traversal is enabled if you're RV320 isn't setup behind another router i think you can disable it.
Under "Local Group Setup" enter the IP Address and Subnet Mask of the LAN you're RV320 is part of.
The preshared key you enter under IPSec setup is entered in Shrew in the "Authentication" --> "Credentials" tab.
We use Extended Authetication (Xauth+PSK in Shrew Soft) you need to have a user + password setup under "User Management" tab on the RV320. Once you connect with Shrew Soft it will prompt for a username + password that is setup on the RV320 under the User Management Tab
We're using "Mode Config" the IPSEC cliënt will be assigned a address from the Virtual IP Address range.
In this example DNS nor WINS Server have been configured.

Similar Messages

Shrew soft vpn client

I am trying to get the shrew soft vpn client to work with a cisco ipsec vpn on windows server 2012. Has anyone done this with it or similar generic vpn clients?

I don't want to push this thread, but I've finally managed to make a PKGBUILD for it. It's now on AUR (entry 28548) and my first packet there It's necessary to add 'iked' to the DAEMONS list in /etc/rc.conf, start it up once by hand and use ikea-qt to set up and connect to your networks.
Last edited by Basic-Master (2009-07-19 04:23:10)

Vpn config for shrew soft vpn client

I wonder whether I am the only one having these problems.
I can't connect with my windows 7 home premium to Lion server vpn.
I can connect with it through my iphone, so the server works.
Since I am unable to change any security policy stuff I downloaded shrew soft vpn client.
But I can't find any documentation which settings the mac vpn system uses for the connection.
Hope someone can help me

Here is a sample configuration for Remote access VPN using Cisco IPSec VPN Client:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008060f25c.shtml

Help with rv180w and shrew soft vpn

Hi, I'm trying to establish a vpn connection using shrew soft to the router cisco rv180w.
I look and read all I could find but the connection drops when opening the tunel.
There was some tuttorial here in the forum but the links are down.
What I want to acomplish is to establish a communication and be able to access my domain on the network.
Any help with the settings would be greatly apeciated. I'm new to vpn.
Thanks in advance.

Federico,
Try to access the following link. It has good instructions for a similar model. The main difference is that the SA500 has Dual-WAN and the RV180W does not.
https://supportforums.cisco.com/docs/DOC-9378#comment-7216
Here is another tutorial for the RVS4000 that may help:
https://supportforums.cisco.com/docs/DOC-18443
Check out the last post in the following thread as well, which has instructions for the RV220W (Should be exactly the same as RV180W)
https://supportforums.cisco.com/message/4165652#4165652
- Marty

HT4623 Both my iPad and iPhone have a message "Cannot get mail" The connection to server failed. I wen to the Apple store today and he could not do anything. Said maybe it will come back by itself. It has been 36 hours and nothing has happened. Help!!!

I have not been able to connect to the internet on my iPhone and iPad the past 36 hours.Went to the Apple store today and he said that maybe it will come back on it's own. That is the first time that I have been to the apple store with a disappointing resolve. Please help, there has to be an answer?

Your post says you have an iPhone 3G. Is it running iOS 4.2.1, which is the latest iOS it can run? Even if so, it's now quite old (nearly five years). That could be part of the problem.
Anyway, maybe you should delete your mail account (Settings >> Mail, Contacts, Calendars -- if it was still called that back in the iOS 4.2.1 days), and start over.
Here's the Mail Setup Assistant to help you do that:
iPhone Email Setup

Shrew Soft VPN won't connect through 4G LTE - using Pantech UML290

Hey everyone,
I'm using Shrew Soft VPN to connect to my companies network and can't seem to connect when using the 4G broadband. I have no issues using Ethernet/wifi but for some reason I can't establish a connection with using 4G.
I'm currently using the Pantech UML290 to connect to the 4G network. I tried to switch to 3G to see if there was some type of encryption causing the issue. That doesn't resolve it.
Has anyone else experienced this and found a solution?

I opened a case with Verizon and it seems the problem is on their end. To get access to VPN again, you have to downgrade the VZAccess, downgrade the Firmware (that is "required") to an older version, and uninstall Verizon firmware updates in Add/Remove programs. This is the email that VZ sent me:
Thank you for contacting the Verizon Wireless Data Technical Support department through our website. We are sorry to learn that you are unable to connect to your company's VPN when using your UML290 Modem. We are pleased to assist you.
We can certainly understand your frustration when your device does not work as expected. You should be able to connect to your company's VPN service when using the UML290. We will be providing you with steps to check your VZAccess Manager Software version.
After updating to MR2 (Maintenance Release 2) software, the UML290 may not be able to connect to some VPNs. The MR2 software was included in the VZAccess Manager build 7.6.3 (2642j). To check the current version that you are currently running on your computer, please complete the steps provided below:
1. Launch VZAccess Manager
2. Click Help
3. Select About VZAccess Manager
If you are running VZAccess Manager 7.6.3 (2642j), please downgrade the software. To do so, please complete the steps provided below:
1. Browse to http://www.vzam.net/download/download.aspx
2. Select your Operating System
3. Select the device you are using
4. Select your hardware i.e. Pantech UML290
5. Click Continue
6. Click the Downgrade Utility link located under the Installation Instructions and/or Device Drivers
You should be able to use the steps provided above to downgrade the VZAccess Manager Software. Once this has been completed, you should be able to connect to your company's VPN when using the Pantech UML290.
Make sure you read the read_me.pdf doc packaged with the firmware downgrade utility. There are some steps that are left out of this procedure that are in that doc. Good luck to everyone.
-daddy

VPN Client cannot access Internet

I am currently using PIX 501 and VPN 3000. Everything is running fine except that VPN Client cannot access internet after they logged in via Cisco System VPN CLient. I can't any solution to this problem and is really lost. This is a very important task assign to me.
Hope someone can help me asap.
Thanks You

You need to enable split tunneling. This link is for VPN client to router. The same equivalent config may apply to a PIX as well.
http://www.cisco.com/application/pdf/en/us/guest/products/ps6659/c1650/cdccont_0900aecd80313bf8.pdf

I have two faults! 1, an error comes up in Ps CC 2014 "could not apply the saved panel configuration, restring to default and my tools have disappeared completely and anything ive tried I cannot get them back not even the drop down menu in 'window' helps

I have two faults! 1, an error comes up in Ps CC 2014 "could not apply the saved panel configuration, restring to default and my tools have disappeared completely and anything ive tried I cannot get them back not even the drop down menu in 'window' helps at all. And 2, Lr everytime I load it up it gives me the option to retry or switch to and it takes a while for me to even get anywhere with it I think it has something to do with the catalogs? I've been using these programs for a few years now on a Mac...no problem but when I use a PC when I'm away coz it's the (only) comp available these happen PC's are so useless! Please can anyone help??...

I can give a few suggestions on Photoshop CC 2014, but Lightroom is a separate forum and you should ask Lr questions there.
First close Photoshop.
Then start Photoshop by double-clicking on it's icon and very quickly after that, hold down the ctrl-alt-shift keys until you see the reset dialog. answer "Yes" to delete settings, and let Photoshop continue to load.
It's tricky to do and may take a few tries, but at least it should reset Photoshop CC 2014 to defaults.
Gene

I keep getting an error pop-up when I try to access my email. The pop-up says Cannot Get Mail The connection to the server failed. I get this pop-up on both my iPhone 5 and my iPad. I can still access my email, but the pop-up is real annoying.

I keep getting an error pop-up when I try to access my email. The pop-up says Cannot Get Mail The connection to the server failed. I get this pop-up on both my iPhone 5 and my iPad. I can still access my email, but the pop-up is real annoying. Can someone please help me with this? -Stu

Hi StuNYC,
Welcome to Apple Support Communities.
It sounds like you're seeing an alert message when opening Mail on your iOS devices. Do you have multiple email accounts setup on the devices? Take a look at the article below, it provides suggestions that will resolve most issues that cause an alert like that to appear in when starting the Mail app.
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
I hope this helps.
-Jason

TS4062 On my Iphone I have 1-Camera roll, two Photo Libraries, and 1 delete. I cannot get rid of the Photo albums off the phone. I cannot take things off my Iphone using the itunes because it doesn't pull the Iphone up.

On my Iphone I have 1-Camera roll, two Photo Libraries, and 1 delete. I cannot get rid of the Photo albums off the phone. I cannot take things off my Iphone using the itunes because it doesn't pull the Iphone up.

Pat2006 wrote:
I cannot take things off my Iphone using the itunes because it doesn't pull the Iphone up.
Correct. You don't use iTunes to get photos off the iPhone.
See this -> http://support.apple.com/kb/HT4083

I installed the new 7.0 on my ipad and now I cannot get my internet connection to work. Any ideas, I have already tried rebooting but no luck. Another useless apple update that doesnt work?

I installed the new 7.0 on my ipad and now I cannot get my internet connection to work. Any ideas, I have already tried rebooting but no luck. Another useless apple update that doesnt work?

1. Turn router off for 30 seconds and on again.
2. Settings>General>Reset>Reset Network Settings.

I lost my password and cannot log on to my MacBook Pro. MacOS X window opens upon startup, with my log on name, requesting password, but I cannot remember it. Is there a way to bypass this window and reset my password? Cannot get to System Preferences

I lost my password and cannot log on to my MacBook Pro. MacOS X window opens upon startup, with my log on name, requesting password, but I cannot remember it. Is there a way to bypass this window and reset my password? Cannot get to System Preferences or Apple Menu
Thanks!

Yes.
https://discussions.apple.com/thread/4913069

Ihave downloaded iCloud to my new PC and am using windows 7 and office 2010. I cannot get iCloud to come up on Outlook with the choices for CalendCar and contacrts, my iMail account is there, but not the general coud choices. What am I doing wrong.

I have downloaded iCloud to my new PC and am using Windows 7 and Offie 2010. I cannot get iCloud to come up on Outlook with the choices for Calendar and Contacts, my iMail accnt is there***.me.com, but not the general Cloud choices for calendar and contacts? What am I doing wrong?

I have I cloud 2.0.2.187 loaded just downloaded yesterday.

HI, I just bought an iPhone 4S. Although my iPad and other iPhone 3GS connect to our server (SBS2003) I cannot get through. It checks all items in the connection and then I get the message :Cannot get mail, the connection to the server failed."

HI, I just bought an iPhone 4S. Although my iPad and other iPhone 3GS connect to our server (SBS2003) I cannot get through. It checks all items in the connection and then I get the message :Cannot get mail, the connection to the server failed." I Tried everything, rebooting, reset all iPhone, etc. All Apple devices work perfectly expect mine. Please advise

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
On your iPad go to Settings > General > Reset > Reset network settings and see if that enables you to connect.
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom

Suddenly my iPhone and all other apple devices have stopped letting me access my emails. I keep getting the message "cannot get mail, the connection to the server failed". Can anyone help?

All my apple devices have suddenly stopped allowing me to access my email account. I keep getting a message saying "cannot get mail, the connection to the sever failed". What has happened and how do I fix it?

Have you seen this? Take a look. There are issues with Microsoft services today.
https://status.live.com/

RV320 and Shrew Soft vpn client - cannot get it to connect

Similar Messages

Maybe you are looking for