RV320 DMZ & DIAG are red upon power up, network is down.
Both the DMZ & DIAG are red when my RV was rebooted after it hung.
I am now unable to get an IP from the router.
Any advice how to proceed from here ?
Thanks.
Corrections: Only DIAG is red
additions : I have also performed a hard reset on the router. It is still in the same state, powered up but DIAG light is still red.
Hi,
You can try to recover the firmware. from cisco.com. Download the firmware that you have present on the device. If you didn't notice the firmware version, download the latest firmware.
You may find the procedure in the end of the release notes. It is called "Firmware Recover Steps Using TFTP":
http://www.cisco.com/c/dam/en/us/td/docs/routers/csbr/rv320/release_notes/rv32x_relnote_v1_1_1_19.pdf
Hereby the same procedure but using a tftpd32 software:
http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=0be53470450c4b42967d61b89ea4d00f_RV320_Router_inaccessible_after_firmware_upgrade.xml&pid=2&respid=0&snid=3&dispid=0&cpage=search
Regards,
Kremena
Similar Messages
-
for the last several days I have experienced the dreaded wite screen of death upon power up of my 2008 Mac Pro 2.8,
Screen will hang white - no apple logo - when I hit the power button resart - the mac power light does not go out, but "clicks" and the mac will restart.
I get the white apple logo screen and then some terminal script (about 20-25 lines) that lasts for a dew seconds - then an apple message appears telling me that my computer needs to be restarted due to an error - press a key or wat.... this will cycle continuously.
If I power down and boot in safe mode - the computer seems to start up - with a crash log.
Once I restart from safe mode - the mac seems to start fine and I am using it without issue - (of course until I power down and come back in the studio the following day...)
I am not familiar with crash logs - but here are the two most recent...
Interval Since Last Panic Report: 25449 sec
Panics Since Last Report: 1
Anonymous UUID: 68CEF3A2-4EFE-D602-DB91-4A773D0A413B
Wed Jul 31 21:26:23 2013
panic(cpu 2 caller 0xffffff801109e53b): "TLB invalidation IPI timeout: " "CPU(s) failed to respond to interrupts, unresponsive CPU bitmap: 0x80, NMIPI acks: orig: 0x0, now: 0x0"@/SourceCache/xnu/xnu-2050.24.15/osfmk/x86_64/pmap.c:2337
Backtrace (CPU 2), Frame : Return Address
0xffffff82f8cdbaa0 : 0xffffff801101d626
0xffffff82f8cdbb10 : 0xffffff801109e53b
0xffffff82f8cdbb90 : 0xffffff80110a2d50
0xffffff82f8cdbc50 : 0xffffff80110a3585
0xffffff82f8cdbca0 : 0xffffff801106720c
0xffffff82f8cdbd90 : 0xffffff801106b0e0
0xffffff82f8cdbdc0 : 0xffffff8011065bdf
0xffffff82f8cdbdf0 : 0xffffff8011402243
0xffffff82f8cdbe10 : 0xffffff8011464c0c
0xffffff82f8cdbe50 : 0xffffff80110943a3
0xffffff82f8cdbe80 : 0xffffff8011020b3d
0xffffff82f8cdbeb0 : 0xffffff8011010448
0xffffff82f8cdbf00 : 0xffffff801101961b
0xffffff82f8cdbf70 : 0xffffff80110a6536
0xffffff82f8cdbfb0 : 0xffffff80110ce9e3
BSD process name corresponding to current thread: powerd
Boot args: arch=x86_64
Mac OS version:
12E55
Kernel version:
Darwin Kernel Version 12.4.0: Wed May 1 17:57:12 PDT 2013; root:xnu-2050.24.15~1/RELEASE_X86_64
Kernel UUID: 896CB1E3-AB79-3DF1-B595-549DFFDF3D36
Kernel slide: 0x0000000010e00000
Kernel text base: 0xffffff8011000000
System model name: MacPro3,1 (Mac-F42C88C8)
System uptime in nanoseconds: 12797763977
last loaded kext at 11912907618: com.apple.driver.AppleUpstreamUserClient 3.5.10 (addr 0xffffff7f92a7b000, size 36864)
loaded kexts:
com.uaudio.driver.UAFWAudio 4.1.1 16344
com.motu.driver.USBMidiKext 1.6 49190
com.uaudio.driver.UAD2System 7.1.0
com.motu.driver.PCIAudio 1.6 57985
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.driver.AppleMCCSControl 1.1.11
com.apple.driver.AppleHDAHardwareConfigDriver 2.3.7fc4
com.apple.kext.AMDFramebuffer 8.1.2
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.driver.AppleHDA 2.3.7fc4
com.apple.ATIRadeonX2000 8.1.2
com.apple.iokit.CSRBluetoothHCIControllerUSBTransport 4.1.4f2
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.ApplePolicyControl 3.4.5
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleMCEDriver 1.1.9
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.CSRHIDTransitionDriver 4.1.4f2
com.apple.driver.AppleFireWireStorage 3.1.7
com.apple.driver.initioFWBridge 3.1.7
com.apple.driver.IOFireWireSerialBusProtocolSansPhysicalUnit 3.1.7
com.apple.driver.LSI_FW_500 3.1.7
com.apple.driver.Oxford_Semi 3.1.7
com.apple.driver.StorageLynx 3.1.7
com.apple.driver.PioneerSuperDrive 3.1.7
com.apple.iokit.SCSITaskUserClient 3.5.5
com.apple.driver.AppleFileSystemDriver 3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.3.1
com.apple.driver.AppleIntel8254XEthernet 3.1.1b1
com.apple.driver.AppleUSBHub 5.5.5
com.apple.driver.AppleAHCIPort 2.5.2
com.apple.driver.AppleIntelPIIXATA 2.5.1
com.apple.driver.AppleFWOHCI 4.9.6
com.apple.driver.AppleUSBEHCI 5.5.0
com.apple.driver.AppleUSBUHCI 5.2.5
com.apple.driver.AppleEFINVRAM 1.7
com.apple.driver.AppleACPIButtons 1.7
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.7
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2.1
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.AppleSMBusController 1.0.11d0
com.apple.driver.AppleUSBAudio 2.9.0f8
com.apple.iokit.IOSurface 86.0.4
com.apple.driver.DspFuncLib 2.3.7fc4
com.apple.iokit.IOBluetoothFamily 4.1.4f2
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.1.4f2
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleGraphicsControl 3.4.5
com.apple.iokit.IONDRVSupport 2.3.7
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.AppleHDAController 2.3.7fc4
com.apple.iokit.IOHDAFamily 2.3.7fc4
com.apple.driver.AppleSMC 3.1.4d2
com.apple.driver.IOPlatformPluginFamily 5.3.0d51
com.apple.kext.AMD2600Controller 8.1.2
com.apple.kext.AMDSupport 8.1.2
com.apple.iokit.IOGraphicsFamily 2.3.7
com.apple.driver.AppleSMBusPCI 1.0.11d0
com.apple.iokit.IOAudioFamily 1.8.9fc11
com.apple.kext.OSvKernDSPLib 1.6
com.apple.driver.AppleUSBHIDKeyboard 170.2
com.apple.driver.AppleHIDKeyboard 170.2
com.apple.iokit.IOUSBHIDDriver 5.2.5
com.apple.driver.AppleUSBMergeNub 5.5.5
com.apple.iokit.IOSCSIBlockCommandsDevice 3.5.5
com.apple.iokit.IOUSBMassStorageClass 3.5.1
com.apple.driver.AppleUSBComposite 5.2.5
com.apple.iokit.IOFireWireSerialBusProtocolTransport 2.1.1
com.apple.iokit.IOFireWireSBP2 4.2.2
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.5
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOATAPIProtocolTransport 3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.5
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOUSBUserClient 5.5.5
com.apple.iokit.IOAHCIFamily 2.3.1
com.apple.iokit.IOATAFamily 2.5.1
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOUSBFamily 5.6.0
com.apple.iokit.IOHIDFamily 1.8.1
com.apple.driver.AppleEFIRuntime 1.7
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220.3
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 345
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.21
com.apple.driver.AppleACPIPlatform 1.7
com.apple.iokit.IOPCIFamily 2.7.3
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
Model: MacPro3,1, BootROM MP31.006C.B05, 8 processors, Quad-Core Intel Xeon, 2.8 GHz, 26 GB, SMC 1.25f4
Graphics: ATI Radeon HD 2600 XT, ATI Radeon HD 2600, PCIe, 256 MB
Memory Module: DIMM Riser B/DIMM 1, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x00004D5035313241373243503444332D5336
Memory Module: DIMM Riser B/DIMM 2, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x00004D5035313241373243503444332D5336
Memory Module: DIMM Riser A/DIMM 1, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x00004D5035313241373243503444332D5336
Memory Module: DIMM Riser A/DIMM 2, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x00004D5035313241373243503444332D5336
Memory Module: DIMM Riser B/DIMM 3, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
Memory Module: DIMM Riser B/DIMM 4, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
Memory Module: DIMM Riser A/DIMM 3, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x00004D5035313241373243503444332D5336
Memory Module: DIMM Riser A/DIMM 4, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x00004D5035313241373243503444332D5336
Bluetooth: Version 4.1.4f2 12041, 2 service, 18 devices, 0 incoming serial ports
Network Service: Ethernet 1, Ethernet, en0
PCI Card: ATI Radeon HD 2600, sppci_displaycontroller, Slot-1
PCI Card: pci137a,5, sppci_audio, Slot-2@2,0,0
PCI Card: pci1a00,1, sppci_othermultimedia, Slot-4
PCI Card: pci1a00,1, sppci_othermultimedia, Slot-3
Serial ATA Device: WDC WD3200AAJS-41VWA1, 320.07 GB
Serial ATA Device: ST31000333AS, 1 TB
Serial ATA Device: ST31000528AS, 1 TB
Serial ATA Device: ST31000528AS, 1 TB
Parallel ATA Device: PIONEER DVD-RW DVR-112D
USB Device: USB2.0 Hub, 0x05e3 (Genesys Logic, Inc.), 0x0608, 0xfd300000 / 3
USB Device: USB2.0 Hub, 0x05e3 (Genesys Logic, Inc.), 0x0608, 0xfd340000 / 7
USB Device: MIDI Timepiece AV, 0x07fd, 0x0001, 0xfd343000 / 10
USB Device: iLok, 0x088e, 0x5036, 0xfd342000 / 9
USB Device: Keyboard Hub, apple_vendor_id, 0x1006, 0xfd341000 / 8
USB Device: Apple Keyboard, apple_vendor_id, 0x024f, 0xfd341200 / 14
USB Device: Keyboard Hub, apple_vendor_id, 0x1006, 0xfd330000 / 6
USB Device: Kensington Expert Mouse, 0x047d (Kensington), 0x1020, 0xfd333000 / 13
USB Device: Keystation Mini 32, 0x0a4d (Evolution Electronics Ltd.), 0x129d, 0xfd331000 / 12
USB Device: Apple Keyboard, apple_vendor_id, 0x0220, 0xfd332000 / 11
USB Device: iLok, 0x088e, 0x5036, 0xfd320000 / 5
USB Device: Eleven Rack, 0x0dba, 0xb011, 0xfd310000 / 4
USB Device: DISK 2.0, 0x090c (Silicon Motion, Inc. - Taiwan), 0x1000, 0xfd100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8206, 0x5d200000 / 3
USB Device: MIDISPORT 4x4 Anniv, 0x0763 (M-Audio), 0x1060, 0x5d100000 / 2
FireWire Device: built-in_hub, 800mbit_speed
FireWire Device: Oxford ATA Device 00, Glyph Technologies, 800mbit_speed
FireWire Device: Oxford ATA Device 00, Glyph Technologies, 800mbit_speed
Interval Since Last Panic Report: 301848 sec
Panics Since Last Report: 1
Anonymous UUID: 68CEF3A2-4EFE-D602-DB91-4A773D0A413B
Mon Jul 29 22:46:13 2013
panic(cpu 4 caller 0xffffff80028a20a6): "Spinlock acquisition timed out: lock=0xffffff8002ebebb0, lock owner thread=0xffffff80356dc340, current_thread: 0xffffff80364df000, lock owner active on CPU 0x0, current owner: 0xffffff80356dc340"@/SourceCache/xnu/xnu-2050.24.15/osfmk/i386/locks_i386.c:363
Backtrace (CPU 4), Frame : Return Address
0xffffff82ea652d70 : 0xffffff800281d626
0xffffff82ea652de0 : 0xffffff80028a20a6
0xffffff82ea652f10 : 0xffffff80028a199b
0xffffff82ea652f30 : 0xffffff8002865623
0xffffff82ea652fe0 : 0xffffff8002843df7
0xffffff82ea6530c0 : 0xffffff80028de568
0xffffff82ea653110 : 0xffffff80028de025
0xffffff82ea6531c0 : 0xffffff80028dd2db
0xffffff82ea6531f0 : 0xffffff80028dd487
0xffffff82ea653210 : 0xffffff8002ae7a26
0xffffff82ea653280 : 0xffffff8002b205ac
0xffffff82ea6532a0 : 0xffffff8002b21674
0xffffff82ea653340 : 0xffffff8002b1d600
0xffffff82ea653450 : 0xffffff8002b198fc
0xffffff82ea653500 : 0xffffff8002b196ca
0xffffff82ea653580 : 0xffffff800291366f
0xffffff82ea6535d0 : 0xffffff8002909d01
0xffffff82ea653610 : 0xffffff8002910a5d
0xffffff82ea653670 : 0xffffff8002910580
0xffffff82ea6536e0 : 0xffffff80028f44cc
0xffffff82ea653a40 : 0xffffff8002b40d3a
0xffffff82ea653aa0 : 0xffffff80028f535e
0xffffff82ea653af0 : 0xffffff800290905e
0xffffff82ea653b90 : 0xffffff80028fb839
0xffffff82ea653c40 : 0xffffff80028fc004
0xffffff82ea653f50 : 0xffffff8002be16aa
0xffffff82ea653fb0 : 0xffffff80028ce9c3
BSD process name corresponding to current thread: revisiond
Boot args: arch=x86_64
Mac OS version:
12E55
Kernel version:
Darwin Kernel Version 12.4.0: Wed May 1 17:57:12 PDT 2013; root:xnu-2050.24.15~1/RELEASE_X86_64
Kernel UUID: 896CB1E3-AB79-3DF1-B595-549DFFDF3D36
Kernel slide: 0x0000000002600000
Kernel text base: 0xffffff8002800000
System model name: MacPro3,1 (Mac-F42C88C8)
System uptime in nanoseconds: 17103336694
last loaded kext at 15943261762: com.apple.driver.AppleHDAHardwareConfigDriver 2.3.7fc4 (addr 0xffffff7f844d3000, size 16384)
loaded kexts:
com.uaudio.driver.UAFWAudio 4.1.1 16344
com.motu.driver.USBMidiKext 1.6 49190
com.uaudio.driver.UAD2System 7.1.0
com.motu.driver.PCIAudio 1.6 57985
com.apple.driver.AppleHDAHardwareConfigDriver 2.3.7fc4
com.apple.iokit.CSRBluetoothHCIControllerUSBTransport 4.1.4f2
com.apple.driver.AppleHDA 2.3.7fc4
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.driver.AppleMCCSControl 1.1.11
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.kext.AMDFramebuffer 8.1.2
com.apple.driver.AppleMCEDriver 1.1.9
com.apple.driver.ApplePolicyControl 3.4.5
com.apple.ATIRadeonX2000 8.1.2
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.CSRHIDTransitionDriver 4.1.4f2
com.apple.driver.AppleFireWireStorage 3.1.7
com.apple.driver.initioFWBridge 3.1.7
com.apple.driver.IOFireWireSerialBusProtocolSansPhysicalUnit 3.1.7
com.apple.driver.LSI_FW_500 3.1.7
com.apple.driver.Oxford_Semi 3.1.7
com.apple.driver.StorageLynx 3.1.7
com.apple.driver.PioneerSuperDrive 3.1.7
com.apple.iokit.SCSITaskUserClient 3.5.5
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.3.1
com.apple.driver.AppleFileSystemDriver 3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.AppleUSBHub 5.5.5
com.apple.driver.AppleIntel8254XEthernet 3.1.1b1
com.apple.driver.AppleFWOHCI 4.9.6
com.apple.driver.AppleAHCIPort 2.5.2
com.apple.driver.AppleIntelPIIXATA 2.5.1
com.apple.driver.AppleUSBEHCI 5.5.0
com.apple.driver.AppleUSBUHCI 5.2.5
com.apple.driver.AppleEFINVRAM 1.7
com.apple.driver.AppleACPIButtons 1.7
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.7
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2.1
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.AppleUSBAudiocom.uaudio.driver.UAFWAudio 4.1.1 16344
com.motu.driver.USBMidiKext 1.6 49190
com.uaudio.driver.UAD2System 7.1.0
com.motu.driver.PCIAudio 1.6 57985
Remove the third party uaudio and motu drivers then restart your Mac.
Once I restart from safe mode - the mac seems to start fine and I am using it without issue
Safe Mode only loads required kernel extensions which is why Safe Mode works, "without issue" ... -
Help with Loops!! All loops are RED and unclickable after Leopard upgrade.
I may need to just remove soundtrack pro from my computer and start from scratch again. When I upgraded to Leopard I failed to select preserve user settings when I did an archive and install. So therefore I had to find and drag files to the new library. This is on my Power Mac G5.
I have a Macbook Pro laptop and I used that as a guide of how I have that set up. On my G5, I have all my loops in the same folders they are in on my laptop. When I open STP, and pull up my loop files, they are all listed in red. When I try to click on them, nothing happens.
I have them set up as MAC>Library>Audio>Apple Loops>Apple Loops for Soundtrack Pro, Apple Loops for GarageBand, PowerFX Loops
I am not sure if I am dealing with a bunch of corrupt files and need to start with a new slate or what.
I also noticed that most if not all the audio loops end in .CAF instead of .AIFF in the folders. However when STP is open, the files ARE listed as .aiff files but they are red and non clickable.
Any suggestions appreciated!
Thanks!
Message was edited by: DVX100Shooter
Message was edited by: DVX100Shooter
Message was edited by: DVX100ShooterYea once I rearranged the loops and then opened STP and then Indexed those loops, I got everything back to normal except my Trumpet files. I cannot locate them anywhere. There are only 4 loops but I searched my HD and still can't locate where they are but I got everything else back to working.
-
K9N2 SLI Platinum/ All 4 lights on motherboard are Red
Specs are.
9850 AMD Black Series
600 W PSU OCZ
1066 Ram OCZ Platinum Series 4 gigs
BFG 9800GTX OC 512
OS- Windows XP s3
Problem I have is the manual i got is Multilingual and not very helpful, but what happened is a breaker in my house tripped and cut off power, and this happened while I was gaming on-line. Reset the breaker, turned the computer back on everything boots up fine but all the led lights are red, 4 total. Everything seems to be working just fine, didn't know if it was anything to be worried about or not. Thanks for any replysDidn't know that I would have to update the BIOS if I wanted the 1TB HDD support. Thanks for pointing that out.
Quote from: Scooter71 on 31-January-09, 05:38:58
I didn't know if I should update the bios or not. IM on bios 3.2 and 3.3 is for updated CPU module, Support for 1000GB HDD and Support for L2 Function. So should I or not i guess is what im asking with me having the 9850 AMD Phenom is all. Thanks for any replys... -
i have the K8n plat. and i turned on the computer after i installed my liquid cooling and nothing at all, my pump and fans turn on and all i get are the d-bracket LED 1 and 4 are red. CPU bad? CPU initialization is where it hanges.
my stats are
MSI K8N neor2 plat.
AMD64 3800+
geforce 6800GT
1.0gig OCZ value ram(new ram not in yet)
2 HDD
CDrom
DVD-burner
antec true power 480watt
let me know what you all think.Quote
Originally posted by brono85
Hello all
Today I received my mobo from RMA I put together ouside the case motherboard, processor, video card and the first boot I got the logo screen and nothing. The led on the D-braket are 1/3 are RED and 2/4 are Green. I tried to clear the bios with the jumper but nothing change, also I tried the bios recovery it gave me 5 bit and nothing.
What should I do next?
They did not replace my mobo I got the same one and I don't know what they do to my motherboard. On the sheet it said "Error code: U0H" "Repair: N01" any ideal what kind of repair they do?
Need your help Thank you
Hi,
Do MEMTEST 1st.........
EDIT: 1/3 RED is mem error......
Also 1.7 is best BIOS update, I have used stable with this mainboard.
Will watch thread for replies.
Del -
Yesterday while playing World of warcraft i suddenly lost my internet connection. I checked my router and the power led (green) and the dmz led was solid red??? i cant connect to the router and cant even reset it. I've searched this forum and the internet but havent found anything about the dmz led beeing red.
What do you mean by you can't reset it?
Hard-reset the power-cycle maybe and then re-enter the ports for WoW? -
my macbook air keeps coming up with a message" are u sure u want to shut down..etc" after which it switches off by itself. now it's off and will not power on altogether. any suggestions?
Does it power on if you plug in the charger?
But to be honest I see in your description it says 'Late 2011' so there is a good chance you have warranty right, I would take it to Apple store and let them sort it out -
The music on my iPhone 4 is not working. There are red dots next to the selections and no sound occurs when they are touched.
Can you play those songs in iTunes on your computer?
Make sure they are all part of your iTunes library before you sync and that they were bought with the same AppleID you use on your phone. -
What causes the FP-AI-110 module READY LED to flash upon power up?
The ready light flashes continuously on the FP-AI-110 module upon power up. The power light also seems to have a very short flash as well. The module part number is 184105C-01. The module has worked fine in the application for about two years. It had not been removed from the rail until this problem.
It is most likely that a component in the FP-AI-110 has failed (or been damaged) and the module is not successfully passing the self diagnostic program. To be absolutely certain that the module has failed, try inserting the FP-AI-110 into a different terminal base and make sure the flashing Power/Ready LED's still occur in other terminal bases. You will have to contact National Instruments to arrange an RMA of the module (for repair).
Regards,
Aaron -
Some pictures are RED on my iMovie...
So I have imported pictures onto iMovie clips and the majority have worked well, but some of them are RED and I have no idea why, how to change it ... what can i do? I really want to incorporate these picture onto my slideshow but its RED.
Please help. thanks a millionsuggestion: Make sure there's a .jpg extension added to the file name of the images you wish to use within i-apps.
also if this is an iMovie question, then you may wish to consider posting this question to the appropriate iMovie forum as well so that it gets the attention it deserves. -
648 Max no booting (all leds are RED)
Hello,
I use my 648 Max mother board for 2 year with :
- P4 @ 2,4 Ghz
- two PC2700 DDR 512 Mo
- the D-Bracket 2
- two hard disk
- a nvidia g-force 2
- a lan pci
- sound blaster live! 5.1
Since yesterday, my computer don't start (whithout hardware change) : All D-Bracket 2 LEDs are red.
Is just a mother board problem or the problem can be provided by an another component (like processor, ram, ...)
Thank you
Damientry clear CMOS. Try your CPU on other motherboard. Try other CPU on your motherboard.
-
Obvious power issue effecting all back plane jks. Popping HOURLY (clocked) thru speakers, lites up lamp on doc scanner. Has blown power supply once. "Genius" diag NTF twice B4 power supply blew. Still have same trouble. I made very CLEAR to Genius Bar that it was a hardware issue after they continued to trouble shoot software. I was referred to tier 2 who told me they only worked on SOFTWARE. Does anyone know a more qualified shop who can fix an OBVIOUS mother board issue tracing back to the power supply? I had the same issue with a 20" with 7 visits & had to literally take a video of the trouble before they could figure out the trouble was the video card. From reading the sheer number of posts of the same trouble descriptions going back to 2007, it's all too obvious the path to MSFT is being taken.
-
What are the DC power limitations for the ipad.
What are the DC power limitations for the ipad in a car or airplane. Can I use and recharge the ipad in a car or airplane with a 28 VDC power system?
The iPad charger produces 5V and 1000 mW. You would need an convertor accessory which is compatible with the iPad charging system and produces these output levels
-
So im editing away in FCP 5.1 and i create a new sequence, i copy some footage into that timeline, and start to move it about. Suddenly the thumbnail previews in the canvas (when two clips are snapping) are red and not the pictures. what happened?
Hi:
If you have your Caps Lock key ON, you'll see red windows with a leyend "Preview Disable" (or something like that!). Check that first.
Hope that helps !
Alberto -
Very random pictures are red X's
While in DW8 I hit "preivew in browser" and everything looks
great, nothing wrong at all. But when I uploaded my site just
random pictures are red X's. My nav bar is supposed to be a roll
over type but again, when uploaded it "rolls over" to red X's.
For instance this page.....
http://michellestest.110mb.com/350z/350z.html
This is still in progress.....please keep that in
mind.......this is just a hobby that I'm still new to.......
I know I have other issues. I'm working on those as we speak.
Right now, if anyone can help with what the issue with the pictures
once uploaded is. That's be great.Here is the link to one of those photos taken from your code:
http://michellestest.110mb.com/Documents%20and%20Settings/Michelle/My%20Documents/RFR/350d rivetrain.jpg
That is a complete mess, hard to even imagine how you created
it. The first
part (
http://michellestest.110mb.com/)
looks right but the next portion
(Documents%20and%20Settings/Michelle/My%20Documents/)
points to your harddrive.
Errors like this usually mean you failed to properly define
your site in DW.
Start there. Access DW's Help (F1) and search on "define
site". Read and
follow the directions to correctly define your site. Then you
will have to
re-link all those problem images. HINT: Make certain every
image is inside
your local root folder for the site.
Walt
"[email protected]"
<[email protected]> wrote in message
news:gffm5j$n5u$[email protected]..
> While in DW8 I hit "preivew in browser" and everything
looks great,
> nothing
> wrong at all. But when I uploaded my site just random
pictures are red
> X's. My
> nav bar is supposed to be a roll over type but again,
when uploaded it
> "rolls
> over" to red X's.
>
> For instance this page.....
>
>
http://michellestest.110mb.com/350z/350z.html
>
> This is still in progress.....please keep that in
mind.......this is just
> a
> hobby that I'm still new to.......
>
> I know I have other issues. I'm working on those as we
speak. Right now,
> if
> anyone can help with what the issue with the pictures
once uploaded is.
> That's
> be great.
>
Maybe you are looking for
-
& problem while updating the table
SQL> update users set coname='Falcon Minerals & Metals' where co_id=1020; update users_loc set country='Finland' where co_id=1020;Enter value for metals: old 1: update users set coname='Falcon Minerals & Metals' where co_id=1020 new 1: update use
-
Lost it all in the restore, have been redownloading the ones I bought just fine.. it's the ones I snagged when they were free I am worried about. Will it prompt me that I have already "purchased" this before.. or will it just go ahead and assume I am
-
How to use iPhone as a modem for MBP
bonjour all, after looking up information about how to use my iPhone 3G as a modem to my late 2008 MPB i found a APP called NetShare that was removed by Apple for reasons unknown yet, and i was hoping that with a little luck there might be an alterna
-
File to be created must already exist
The problem I am struggling with is that when creating an Excel file, the user is prompted for the file name. They can browse for the file by clicking on the folder icon, but once they get to the directory they want, if they type in a file that does
-
Grid control and em console !!
We have been using em console for a long time. It is very usefull for us. But we want to go one step further. What is the difference between these two? What will we gain if we use Grid control instead of em console? Thank you very much for the replie