RV320 loosing WAN and inter VLAN connectivity

I just received a new RV320 V01 router and I am having trouble with the router loosing WAN and inter VLAN connectivity. Anywhere from 2 to 24+ hours the router will stop routing traffic to/from the WAN and other VLANs on the network. I have a ping trace running on one system and all packets are lost when the routing fails to all WAN connections and systems on other VLANs. I am still able to ping all of the router address for the VLANs i.e. 192.168.1.1, 192.168.2.1, 192.168.3.1 etc. Unfortunately I only have one system on this VLAN so I do not know if I can ping other systems on the same VLAN. I also do not have any DNS resolution when the issue occurs.
The router is set up using a single ISP connection on WAN1 using DHCP assignment. WAN2 is disabled in the router settings. The router has version v1.1.1.06 firmware. I have also tried disabling VPN pass-through as noted from other posts. When the issue occurs the WAN1 connection is showing as “Connected (Inactive)” with no assigned IP address, gateway or DNS servers. The router is in gateway mode and everything works fine until the problem.
Any Ideas?

You noted that the WAN 1 connection has no IP address when this occurs.
When it occurred last, I noted the "Connected (Inactive)" on WAN1 and that there were no IP addresses assigned. I have a screen shot of the page attached. I had noticed the "Connected (Inactive)" previously when the problem was occurring but cannot definitely say there were no IP addresses at that time. I do not recall if I noticed this before or after I had disconnected the WAN1 to test a direct PC to modem connection. I did check with the cable company and there are no issues being noted or logged on my connection. The direct PC to modem connection worked fine.
What type of Internet connection is it? (Cable, DSL, T1, etc)
The connection is Cable
Is the WAN port configured for DHCP?
The WAN port is configured for DHCP
Who is the ISP?
The ISP is the local cable company
When the issue occurs, can devices within a subnet ping each other?
As I noted in the original post, at the time I was on a VLAN that only had one system running to monitor ping traces. I will try again next time the problem occurs to have multiple devices on the same network.
Are there any switches in the network?
Yes, there is a switch in the system. I am using a cisco SG200-26. However, the problem persists even when I directly connected a PC to the active LAN port on the router. No issue when the PC was dirrectly connected to the modem.
Can you draw a simple topology showing the network with IP addresses, VLANs, etc?
See attached

Similar Messages

2960X and Inter-vlan

I have read from cisco sites that 2960X with Lan base supports up to 16 static routes however I believe this is a layer 2 switch . One of my confusion is that would I be able to do Inter-vlan routing with this . Has anyone tried this ?

Thanks for the reply .
Yes i understand that dyamic routing is not supported . If we have one switch I can make 3 SVI and assign each port to each SVI , later each port can be connected to a Laptop . This way each laptop will have different IP . Because Laptop's default gateway would be SVI created on switch all data would travel there .
Now if i do a show ip route on that switch I will see all 3 SVI as Directly Connected route with an administrative distance of 0 because the line protocol of SVI is up .
My question is would Laptop A be able to ping Laptop B , Intervlan routing ?

RV320 two wan and wifi

Hi,
just buy a RV320 and I have both wan configured to failover.
Wan1 has fix ip and Wan2 has dynamic ip.
I would like to know if i can configure one router to provide WIFI. I tried to create a VLAN in Cisco and isolate wifi but does not work. The router is in bridge mode.
I hope someone can guide me to solve this problem.
thank you very much
pd: sorry for my english but is not my mother tongue....

Hi Marty,
thank you for your answer.
This my configuration:
default Vlan: 172.16.0.1
Vlan2: 192.168.2.1
WAN1: 217.172.x.x
WAN2: dinamic ip PPPoE
The switch is connected to port Lan 1 and an old router to port Lan 2 to provide wifi on an isolated network.
The router has not a special configuration, ip: 192.168.2.2, wifi, dhcp with default gateway 192.168.2.1
i can connect to wifi but i can not ping to 192.168.2.1
any help would be appreciated

SA540 Inter-VLAN ACL Support Options

We have several VLANs, basically a different VLAN for each department (i.e. Developers, Payroll, Accounting, etc.) with Inter VLAN Routing turned off. We have several printers with static IPs that are currently part of a near by VLAN. We would like to group/share most of our printers across all/most of our current VLANs though. How can this be achieved? We don't want to turn Inter VLAN Routing on
If we had to, it may be possible to move all the printers we want to share across the existing VLANs to a new VLAN (and turn Inter VLAN routing on for that VLAN). Would that allow all the existing VLANs access to the new *printer* VLAN? Would all the existing VLANs still be separate and secure from one another?
We were hoping for Inter VLAN Firewall ACL support in the latest firmware as we were told is was on the roadmap for the SA500 Series routers. However, we are currently beta testing the 2.2.0.3_1 firmware and Inter VLAN Firewall ACLs are still not possible to create. Is there anyway to get that into the next firmware release (2.2.0.x) that is coming out soon?

Good morning.
Hi Curtis Counsil my name is Johnnatan and I am part of the Small business Support community, unfortunately it is not possible to create ACL´s in your device, the solution is to enable inter vlan or placing a printer for each vlan's with the inconvenience that it could not communicate with each other, however that's what you do not want. I recommended to you get or buy a Cisco layer 3 device that supports ACL. Such a router or a Switch L3, you can contact our presales team and explain your newortk issue and they will help you with your case
http://www.cisco.com/web/siteassets/contacts/international.html?reloaded=true
Thank you and have a nice day!!!
I hope you find this answer useful, if it was satisfactory for you, please mark the question as Answered.
Best regards.
Johnn.
Cisco network support engineer.

Inter-VLAN routing, Auto-Voice VLAN and IP Address-Helper

Hope that somebody can help me with the setup in the screenshot.
Planning to use Auto-Voice VLAN and Smartports to configure VOIP
LLDP-MED will be enabled on the switch to detect the IP phones so they will be moved to the Voice VLAN (If not the first 6 signs will be added to the OID table). The Voice VLAN ID will be 2 >> Voice VLAN will be automatically enabled once a device is recognized as a IP phone right?
Workstations will be connected to the Cisco switch, VLAN data will be untagged and will remain on the native VLAN.
Smartports will be used to configure the ports (Macro's) >> Should configure the ports as trunks as assigns the correct VLANs right?
But how do i configure the IP Helper-Address? Do i have to create the Voice VLAN on both switches and then run the command "IP Helper Address" to specify a DHCP server? From what i've been reading it's required, when using Inter-VLAN routing, to configure the VLAN interface with an IP address. But it's going to give problems when both switches are connected to eachother and both have the same VLAN configured including the same IP address assigned to their VLAN interface?
Normal data should pass the ASA firewall, VOIP traffic should go through the Vigor modem to a hosted VOIP provider. The best way, i assume, is to configure 2 separate scopes on the DHCP server?
Still confused on how to set it up, hope that someone can point me in the right direction

If you're sending voice to only the Vigor modem then there is no need for a trunk between the SF-300 and the Vigor modem. You can just set that to an untag packet for the VLAN 2 between that switch and the Vigor modem.
On the 'edge' SF300 where the IP phone/PC is it is obviously going to interoute there and of course the phone port is tagged and PC port is untagged.
For the IP helper, it uses UDP-RELAY and it should be enabled on the port itself and enabled on the global configuration. You may also need option 82. Also keep in mind, depending how your DHCP server works, it may need option 82 configured as well or at least a route to understand the subnets in the layer 3 environment to get traffic across the VLANS.

I want to know if Ican connect a print server (to print with several wireless printers) to the new airport express given that it has wan and lan ports. Tks!

The print server that I want to connect allows me to choose among 2 usb printers and 01 serail port printer. It needs to be connected to a router through a lan port. Given that the all new airport express now come with a wan and a lan port, i want to know if I can connect this device to the airport express.

You're welcome.
Beware that while USB print servers are commonly available and inexpensive, finding one with a serial port is more of a challenge. Apple Stores in the US do not sell them. Call the iStore before going there.
If you need recommendations for obtaining a print server with a serial port, let me know.

My ipod is disabled and it says connect to itunes. the only way i found to fix it is to restore it but i dont want to loose all my data. what should i do?

My iPod is disabled and it says connect to iTunes. The only way i found to fix it is to restore it but i don't want to loose all my data. What should i do?

You must restore it, losing anything you have failed to backup or store on your computer or cloud service.

My ipod keeps on saying ipod is disabled connect to itunes and when i connect it to itunes it says i have to inter a passcode on the ipod to connect to itunes

my ipod keeps on saying ipod is dissabled connect to itunes and whin i connect it to itunes it says i have to inter a passcode on the ipod to connect to itunes what do i do??

hi, may i know how to restore and put it on recovery mode??
as I faced the same problem as you now...
Thanks

Help config vlan and inter routing vlan on 2 switches SF300-24 ???

Dear Cisco!
now we have 2 switches: SF300-24
on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following
VLAN ID 2 (ports: 2 -6) have ip interface 192.168.2.254/24
VLAN ID 3 (ports: 7 - 10) have ip interface 192.168.3.254/24
VLAN ID 4 (ports 11- 15 ) have ip interface 192.168.4.254/24
and VLAN 1 default have IP address: 192.168.1.200
DHCP relay - DHCP server 192.168.3.1
- DHCP relay: VLAN2; VLAN3; VLAN4
ip route: 0.0.0.0 0.0.0.0 192.168.3.1
all ports of VLAN2, VLAN3, VLAN4 set access mode.
and another SF300-24
was configed at layer 2. We config VLAN ID 2 ̣̣̣have ports 2 -6; VLAN ID 3 ports 7 -10; VLAN ID 4 port 11-15 ,too.
And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.
But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3!!!
Could you please help me check this situation?
How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
Thanks!
See you soon!

Son Nquyen,
First i would upgrade to 1.1.8 since the 1.0.0.27 was beta code.
Next when when connecting both switches together each port will need set via Trunk mode with proper native vlan and tagged vlan traffic. What's the configuration of your trunk ports on each switch?
Thanks,
Jasbryan.

I have over 20 songs and apps on my phone and when i connect it to my computer none will transfer over into my Itunes on my computer this is the first time this has done this and i dont want to loose anything

I have over 20 songs and apps on my phone and when i connect it to my computer none will transfer over into my Itunes on my computer this is the first time this has done this and i dont want to loose anything, everything is up to date so im not sure why this is happening

The computer must be authorized to the same account you have on your iPhone. Connect the phone and choose Transfer Purchases from the iTunes File menu.

Inter VLAN Routing with ASA 5520 and Cat 2960

Hi there,
I am a complete novice at networking, but I was tasked to have an ASA 5520 do inter VLAN routing (since my shop doesn't have a layer 3 router).
As a basic setup, I am trying to have three workstations on three different VLANs communicate with each other. The attached screenshot shows the topology.
I am unable to ping from a PC to the ASA...therefore I can't ping to other VLANs. Any assistance would be greatly appreciated.
ROUTER CONFIG:
ciscoasa#
ciscoasa# show run
: Saved
ASA Version 8.3(1)
hostname ciscoasa
domain-name null
enable password ###### encrypted
passwd ###### encrypted
names
dns-guard
interface GigabitEthernet0/0
no nameif
no security-level
no ip address
interface GigabitEthernet0/1
no nameif
security-level 100
ip address 10.10.1.1 255.255.255.0
interface GigabitEthernet0/1.10
vlan 10
nameif vlan10
security-level 100
ip address 10.10.10.1 255.255.255.0
interface GigabitEthernet0/1.20
vlan 20
nameif vlan20
security-level 100
ip address 10.10.20.1 255.255.255.0
interface GigabitEthernet0/1.30
vlan 30
nameif vlan30
security-level 100
ip address 10.10.30.1 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
boot system disk0:/asa831-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name null
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list global_access extended permit icmp any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu vlan10 1500
mtu vlan20 1500
mtu vlan30 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
access-group global_access global
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.1.2-192.168.1.5 inside
dhcpd enable inside
dhcpd address 10.10.10.101-10.10.10.253 vlan10
dhcpd enable vlan10
dhcpd address 10.10.20.101-10.10.20.253 vlan20
dhcpd enable vlan20
dhcpd address 10.10.30.101-10.10.30.253 vlan30
dhcpd enable vlan30
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DD
CEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4ad1bba72f1f51b2a47e8cacb9d3606a
: end
SWITCH CONFIG
Switch#show run
Building configuration...
Current configuration : 2543 bytes
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Switch
boot-start-marker
boot-end-marker
no aaa new-model
system mtu routing 1500
ip subnet-zero
spanning-tree mode pvst
spanning-tree extend system-id
no spanning-tree vlan 1
vlan internal allocation policy ascending
interface GigabitEthernet0/1
description Port Configured As Trunk
switchport trunk allowed vlan 1,10,20,30,1002-1005
switchport mode trunk
interface GigabitEthernet0/2
switchport access vlan 10
switchport mode access
interface GigabitEthernet0/3
switchport access vlan 20
switchport mode access
interface GigabitEthernet0/4
switchport access vlan 30
switchport mode access
interface GigabitEthernet0/5
interface GigabitEthernet0/6
interface GigabitEthernet0/7
interface GigabitEthernet0/8
interface GigabitEthernet0/9
interface GigabitEthernet0/10
interface GigabitEthernet0/11
interface GigabitEthernet0/12
interface GigabitEthernet0/13
interface GigabitEthernet0/14
interface GigabitEthernet0/15
interface GigabitEthernet0/16
interface GigabitEthernet0/17
interface GigabitEthernet0/18
interface GigabitEthernet0/19
interface GigabitEthernet0/20
interface GigabitEthernet0/21
interface GigabitEthernet0/22
interface GigabitEthernet0/23
interface GigabitEthernet0/24
interface GigabitEthernet0/25
interface GigabitEthernet0/26
interface GigabitEthernet0/27
interface GigabitEthernet0/28
interface GigabitEthernet0/29
interface GigabitEthernet0/30
interface GigabitEthernet0/31
interface GigabitEthernet0/32
interface GigabitEthernet0/33
interface GigabitEthernet0/34
interface GigabitEthernet0/35
interface GigabitEthernet0/36
interface GigabitEthernet0/37
interface GigabitEthernet0/38
interface GigabitEthernet0/39
interface GigabitEthernet0/40
interface GigabitEthernet0/41
interface GigabitEthernet0/42
interface GigabitEthernet0/43
interface GigabitEthernet0/44
interface GigabitEthernet0/45
interface GigabitEthernet0/46
interface GigabitEthernet0/47
interface GigabitEthernet0/48
interface Vlan1
ip address 10.10.1.2 255.255.255.0
no ip route-cache
interface Vlan10
no ip address
no ip route-cache
interface Vlan20
no ip address
no ip route-cache
interface Vlan30
no ip address
no ip route-cache
ip default-gateway 10.10.1.1
ip http server
ip http secure-server
control-plane
line con 0
line vty 5 15
end

ciscoasa# capture cap10 interface vlan10
ciscoasa# capture cap20 interface vlan20
ciscoasa# show cap cap10
97 packets captured
   1: 17:32:32.541262 802.1Q vlan#10 P0 10.10.10.101.2461 > 10.10.10.1.8905: ud
p 96
   2: 17:32:36.741294 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
   3: 17:32:36.741523 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
   4: 17:32:37.539217 802.1Q vlan#10 P0 10.10.10.101.2462 > 10.10.10.1.8905: ud
p 98
   5: 17:32:39.104914 802.1Q vlan#10 P0 10.10.10.101.2463 > 10.12.5.64.8906: ud
p 95
   6: 17:32:41.738914 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
   7: 17:32:41.739143 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
   8: 17:32:42.544023 802.1Q vlan#10 P0 10.10.10.101.2464 > 10.10.10.1.8905: ud
p 93
   9: 17:32:46.747352 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
10: 17:32:46.747580 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
11: 17:32:47.546633 802.1Q vlan#10 P0 10.10.10.101.2465 > 10.10.10.1.8905: ud
p 98
12: 17:32:51.739921 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
13: 17:32:51.740150 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
14: 17:32:52.544100 802.1Q vlan#10 P0 10.10.10.101.2466 > 10.10.10.1.8905: ud
p 98
15: 17:32:56.741859 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
16: 17:32:56.742088 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
17: 17:32:57.547396 802.1Q vlan#10 P0 10.10.10.101.2467 > 10.10.10.1.8905: ud
p 98
18: 17:33:01.742728 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
19: 17:33:01.742957 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
20: 17:33:02.547609 802.1Q vlan#10 P0 10.10.10.101.2468 > 10.10.10.1.8905: ud
p 97
21: 17:33:06.742774 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
22: 17:33:06.743018 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
23: 17:33:07.543337 802.1Q vlan#10 P0 10.10.10.101.2469 > 10.10.10.1.8905: ud
p 93
24: 17:33:10.375514 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
25: 17:33:11.114679 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
26: 17:33:11.742728 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
27: 17:33:11.742957 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
28: 17:33:11.864731 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
29: 17:33:12.546266 802.1Q vlan#10 P0 10.10.10.101.2470 > 10.10.10.1.8905: ud
p 98
30: 17:33:16.746497 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
31: 17:33:16.746726 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
32: 17:33:17.548403 802.1Q vlan#10 P0 10.10.10.101.2471 > 10.10.10.1.8905: ud
p 97
33: 17:33:21.744880 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
34: 17:33:21.745109 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
35: 17:33:22.545351 802.1Q vlan#10 P0 10.10.10.101.2472 > 10.10.10.1.8905: ud
p 95
36: 17:33:23.785558 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
37: 17:33:24.522464 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
38: 17:33:25.272568 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
39: 17:33:26.744926 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
40: 17:33:26.745154 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
41: 17:33:27.548708 802.1Q vlan#10 P0 10.10.10.101.2473 > 10.10.10.1.8905: ud
p 96
42: 17:33:31.749625 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
43: 17:33:31.749854 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
44: 17:33:32.550096 802.1Q vlan#10 P0 10.10.10.101.2474 > 10.10.10.1.8905: ud
p 97
45: 17:33:36.748343 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
46: 17:33:36.748572 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
47: 17:33:37.546251 802.1Q vlan#10 P0 10.10.10.101.2475 > 10.10.10.1.8905: ud
p 95
48: 17:33:41.745566 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
49: 17:33:41.745795 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
50: 17:33:42.547975 802.1Q vlan#10 P0 10.10.10.101.2476 > 10.10.10.1.8905: ud
p 97
51: 17:33:46.747855 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
52: 17:33:46.748084 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
53: 17:33:47.548403 802.1Q vlan#10 P0 10.10.10.101.2477 > 10.10.10.1.8905: ud
p 94
54: 17:33:51.747718 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
55: 17:33:51.747931 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
56: 17:33:52.547670 802.1Q vlan#10 P0 10.10.10.101.2478 > 10.10.10.1.8905: ud
p 97
57: 17:33:54.134239 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
58: 17:33:56.750678 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
59: 17:33:56.750891 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
60: 17:33:57.563035 802.1Q vlan#10 P0 10.10.10.101.2479 > 10.10.10.1.8905: ud
p 97
61: 17:33:59.245272 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
62: 17:34:01.752188 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
63: 17:34:01.752402 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
64: 17:34:01.995737 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
65: 17:34:01.995813 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
66: 17:34:01.995950 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
67: 17:34:01.996011 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
68: 17:34:01.996118 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
69: 17:34:01.996179 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
70: 17:34:02.551836 802.1Q vlan#10 P0 10.10.10.101.2480 > 10.10.10.1.8905: ud
p 98
71: 17:34:03.011306 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
72: 17:34:03.011367 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
73: 17:34:03.011443 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
74: 17:34:03.011489 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
75: 17:34:03.011550 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
76: 17:34:03.011596 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
77: 17:34:04.027037 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
78: 17:34:04.027082 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
79: 17:34:04.027174 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
80: 17:34:04.027250 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
81: 17:34:04.027311 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
82: 17:34:04.027357 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
83: 17:34:04.745811 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
84: 17:34:06.058514 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
85: 17:34:06.058605 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
86: 17:34:06.058651 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
87: 17:34:06.058712 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
88: 17:34:06.058758 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
89: 17:34:06.058819 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
90: 17:34:06.750907 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
91: 17:34:06.751151 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
92: 17:34:07.552751 802.1Q vlan#10 P0 10.10.10.101.2481 > 10.10.10.1.8905: ud
p 96
93: 17:34:11.752082 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
94: 17:34:11.752326 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
95: 17:34:12.553392 802.1Q vlan#10 P0 10.10.10.101.2482 > 10.10.10.1.8905: ud
p 96
96: 17:34:16.755438 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
97: 17:34:16.755682 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
98: 17:34:17.554811 802.1Q vlan#10 P0 10.10.10.101.2483 > 10.10.10.1.8905: ud
p 97
99: 17:34:21.751303 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
100: 17:34:21.751563 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
101: 17:34:22.552034 802.1Q vlan#10 P0 10.10.10.101.2484 > 10.10.10.1.8905: ud
p 95
102: 17:34:26.753989 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
103: 17:34:26.754218 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
104: 17:34:27.560334 802.1Q vlan#10 P0 10.10.10.101.2485 > 10.10.10.1.8905: ud
p 98
105: 17:34:31.755499 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
106: 17:34:31.755728 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
107: 17:34:32.563950 802.1Q vlan#10 P0 10.10.10.101.2486 > 10.10.10.1.8905: ud
p 95
107 packets shown
ciscoasa# show cap cap20
92 packets captured
   1: 17:26:53.653378 802.1Q vlan#20 P0 10.10.20.101.1187 > 216.49.94.13.80: S 8
20343450:820343450(0) win 65535
   2: 17:27:12.019133 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
   3: 17:27:17.214481 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
   4: 17:27:55.593688 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
499891746:1499891746(0) win 65535
   5: 17:27:58.555284 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
499891746:1499891746(0) win 65535
   6: 17:28:04.564790 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
499891746:1499891746(0) win 65535
   7: 17:29:06.504856 802.1Q vlan#20 P0 arp who-has 10.10.20.1 tell 10.10.20.101
   8: 17:29:06.504917 802.1Q vlan#20 P0 arp reply 10.10.20.1 is-at 54:75:d0:ba:4
6:bb
   9: 17:29:06.505222 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
7080594:47080594(0) win 65535
10: 17:29:09.467032 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
7080594:47080594(0) win 65535
11: 17:29:15.476537 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
7080594:47080594(0) win 65535
12: 17:30:17.417245 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
445997597:1445997597(0) win 65535
13: 17:30:18.156043 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
14: 17:30:20.378688 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
445997597:1445997597(0) win 65535
15: 17:30:23.220356 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
16: 17:30:26.388102 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
445997597:1445997597(0) win 65535
17: 17:30:28.721047 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
18: 17:30:34.222507 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
19: 17:33:43.156928 802.1Q vlan#20 P0 arp who-has 10.10.20.101 tell 10.10.20.1
01
20: 17:33:44.187002 802.1Q vlan#20 P0 arp who-has 10.10.20.1 tell 10.10.20.101
21: 17:33:44.187047 802.1Q vlan#20 P0 arp reply 10.10.20.1 is-at 54:75:d0:ba:4
6:bb
22: 17:33:44.187261 802.1Q vlan#20 P0 10.10.20.101 > 10.10.20.1: icmp: echo re
quest
23: 17:33:44.187520 802.1Q vlan#20 P0 10.10.20.1 > 10.10.20.101: icmp: echo re
ply
24: 17:33:44.239016 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
25: 17:33:44.327360 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
26: 17:33:44.989740 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
27: 17:33:45.150611 802.1Q vlan#20 P0 10.10.20.101.6646 > 10.10.20.255.6646:
udp 236
28: 17:33:45.331312 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
udp 34
29: 17:33:45.740943 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
30: 17:33:46.331892 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
31: 17:33:46.492131 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
32: 17:33:47.243502 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
33: 17:33:47.994501 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
34: 17:33:48.335050 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
35: 17:33:48.335141 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
udp 34
36: 17:33:48.745658 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
37: 17:33:49.496861 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
38: 17:33:50.248812 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
39: 17:33:50.249300 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
40: 17:33:50.999170 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
41: 17:33:50.999246 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
42: 17:33:51.750342 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
43: 17:33:51.750418 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
44: 17:33:52.341336 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
45: 17:33:52.341474 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
udp 34
46: 17:33:52.501576 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
47: 17:33:52.501652 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
48: 17:33:53.254183 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
49: 17:33:53.254320 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 204
50: 17:33:54.134361 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
51: 17:33:54.755118 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
52: 17:33:54.823535 802.1Q vlan#20 P0 10.120.2.198.1261 > 161.69.12.13.443: R
250934743:250934743(0) ack 2427374744 win 0
53: 17:33:54.823901 802.1Q vlan#20 P0 10.120.2.198.1262 > 161.69.12.13.443: R
3313764765:3313764765(0) ack 1397588942 win 0
54: 17:33:54.824618 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
2860571026:2860571026(0) win 65535
55: 17:33:56.257448 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
56: 17:33:57.759833 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
57: 17:33:57.779729 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
2860571026:2860571026(0) win 65535
58: 17:33:59.245394 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
59: 17:33:59.262178 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
60: 17:34:00.263780 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
61: 17:34:01.265382 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
62: 17:34:02.266908 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
63: 17:34:03.268540 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
64: 17:34:03.789189 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
2860571026:2860571026(0) win 65535
65: 17:34:04.019591 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
66: 17:34:04.745933 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
67: 17:34:04.770757 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
68: 17:34:05.521991 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
69: 17:34:06.273209 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
70: 17:34:07.024367 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
71: 17:34:07.775518 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
72: 17:34:08.526706 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
73: 17:34:09.277939 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
74: 17:34:09.278061 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
75: 17:34:09.278702 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 204
76: 17:34:15.810489 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
77: 17:34:16.809726 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
udp 31
78: 17:34:17.811222 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
79: 17:34:19.814349 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
80: 17:34:19.814380 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
udp 31
81: 17:34:23.820682 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
82: 17:34:23.820788 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
udp 31
83: 17:34:30.822924 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 50
84: 17:34:31.572892 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 50
85: 17:34:32.324079 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 50
86: 17:34:33.083079 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
87: 17:34:34.077007 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
udp 44
88: 17:34:35.078639 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
89: 17:34:37.081584 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
90: 17:34:37.081706 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
udp 44
91: 17:34:41.087809 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
92: 17:34:41.087840 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
udp 44
92 packets shown

RV320 - Dual WAN - Load Balance Problem

Hi all,
I've just bought a RV320 Dual WAN router an try to get it running. My network setup looks lice the picture attached.
I have 2 WAN Connections:
- Router 1 (16Mbit Down / 512kbit up) - no public WAN IP
- Router 2 (3 Mbit Down / 512kbit up) - Fixed public IP
Router 1 ist connected to WAN1 and router 2 to WAN2 port on the RV320.
I have enabled load balancing mode.
Qustions:
1.
I want WAN1 to be the primary line to be used until capacity reached.
Currently for some reason I don't understand the cisco always uses WAN2.
That's not good as all browsing and downloading is limited to 3mbit.
When I switch to "fail-over" mode and set primry live to WAN1 that works, but WAN2 is not kept alive.
2.
I am using VOIP and need to route all VOIP traffic to WAN2 interface.
The best would be to tell the router IP 192.168.177.9 (voip phone) should use WAN2. So far I didn't figure out how to do that.
Can I put VOIP into one VLAN group and allocated VLAN to one specific WAN interface?
Brgds

So, you can hear the phone ringing and answer it? which means that SIP pakets are coming through WAN to LAN and well redirected to the phone IP, but you cannot hear after that, which means that there could be a problem with the RTP packets.
If you have problem only with the incoming calls and not the outgoing, than try enable/disable SIP ALG (Firewall). If that doesn't fix the issue, try to allow (or even forward) from WAN to LAN RDP - UDP ports 16384-32767 to the phone IP.
Regards,
Kremena

Inter Vlan Routing on a Cisco 861 Router

Hi all
I have a Network with 2 Subnets (2 DHCP servers) , Cisco Switch and a Cisco 861 Router.
On the Router
Fa 4 (WAN port) is connected to the ADSL line
All other 4 ports which are layer 2 ports
I need to achieve inter vlan routing
I have created 2 SVI's and assigned the default ip address on these SVI vlans
I have selected fa 3 as the uplink trunk port that connects to the Switch.
The config on the Fa 3 Trunk port is as shown below
switchport mode trunk
switchport trunk encapsulation dot.1q
switchport trunk allowed vlan all
This config does not show up on the Show Run config even though i did configure it. Is that normal ?
so will inter vlan routing work in this way ?
there should be only one connection between switch and router
Many Thanks.

Hi David,
I have enabled what you have specified above which has blocked traffic both ways but it seems to be ignoring all rules to allow RDP, SMTP, IMAP, FTP ect. Settings shown below:
Rules 34 - 38 seem to be ignored for some reason not sure why?
Kind Regards
Richard

RVS4000 V1 tracks some VLAN to VLAN connections backwards

Firmware         V1.3.3.5
Operation Mode:        Gateway
VLANs:             4, one per LAN subnet
Inter-VLAN Routing:     Enabled
I've got all of the management interfaces of the infrastructure devices
(switches, UPS,WAPs) on the default VLAN 1 that is configured on as untagged on
all relevant ports. I've noticed that the router will track most of the routed
connections from the non-default VLANs to devices on the devices on the default
VLAN backwards, where the destination is listed as the source and vice versa,
often with the SYN_SENT state instead of ESTABLISHED as reported by the source
host.
I get this information from the IP Conntrack view launched from the
Status/Gateway screen. This is how a telnet connection from a computer on the
guest VLAN 3, subnet 10.0.89.0/24 to the default mgmt VLAN 1, subnet
192.168.75.0 looks in IP Conntrack
Basic Information                 Original Direction                             Reply Direction
Protocol     Life Time     State         Source IP     Source Port     Destination IP     Destination Port     Source IP     Source Port    Destination IP     Destination Port
TCP         44         SYN_SENT     192.168.75.98     23         10.0.89.2     50196             10.0.89.2     50196         192.168.75.98     23
Also, there are corresponding entries in the router's access log.
Jan 29 22:26:00 - [Access Log]I TCP Packet - 192.168.75.98:23 --> 10.0.89.2:50196
Notice that it is incoming as expected as opposed to outgoing (to the WAN port).
I know that these are routed connections, for when I turn off Inter-VLAN
Routing, I cannot make any connections from on VLAN subnet to another.
This reversed connection tracking anomaly is causing the firewall ACLs that I have
implemented to block traffic from the guest VLAN (3) to the default
(infrastructure) VLAN to not work, since ACLs are defined based on source IP
and destination IP. Connections to other VLANs other than the default appear as expected
in the access log and the IP Conntrack view.
Is this a known bug with the RVS4000 V1?

Thanks for answer.
I investigated thread you sent and found there the solution, which can be shorten to one line:
Setup -> Advanced Routing -> Inter-VLAN Routing -> Disable
Once more, Many THX
It works and is solved.

RV042G Router - Inter VLAN

RV042G Router - Inter VLAN:
Does this router supports 802.1Q? Or should I connect one router port per VLAN?
eg. If I have 2 VLAN configured on ONE SWITCH, Do I:
a) TRUNK the VLAN on SWITCH and connect ONE port to the ROUTER?
b) connect ONE port on ROUTER to VLAN1, and another port to VLAN2?
Thanks,
Henrique

Hello Henrique,
I don't usually deal with sales or pricing, so I'm honestly not sure which routers are low priced. However, all of the RVs except for the RV016, RV042, and RV082 support VLAN trunking, so I would just compare the other models and see what kind of a deal you can get. I usually recommend the RV180 (which is being replaced by the RV130 soon) or maybe the RV320 if you want the newest one.
With your SG200 you will probably need to disable spanning tree on the uplinks to your RV042 for the multiple links to work, but a quick check of the Spanning Tree, RTP Interface status page on the SG will let you know if those links are being taken down.
Thank you for choosing Cisco,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center

RV320 loosing WAN and inter VLAN connectivity

Similar Messages

Maybe you are looking for