RV320 - Using Specific WAN Setting

Hi All,
I am new to RV320 and I would like to know that how can I set an IP address using specific WAN (say Wan 1) connection when load balance is enable.
Thanks,
Eric

Hi Eric,
You should be able to achieve it by using protocol binding settings:
Dual WAN--> click on WAN (1 or 2) icon --> scroll down to protocol binding --> add specific rule for all services where source IP address would be your particular LAN host IP (repeated twice if it is only 1 host) and destination 0.0.0.0 (repeated twice) choose desire WAN1 or WAN2.
I hope this helps,
Aleksandra

Similar Messages

  • RV320 - using one WAN port

    What is the correct configuration for using one WAN port so that the router doesn't crash several times a day?
    Should WAN2 be left as address from IP ?
    Shoudl WAN2 be configured as static IP ?
    Should WAN2 interface be disabled?
    Should WAN2 be configured as DMZ and left as default 192.168.1.0?
    Should WAN2 be configured as DMZ and then disabled?
    It's definitely the router which is at fault, power cycling the fibre to copper converter dosen't fix the issue.
    Nor does swapping the FTC for a brand new one.
    Only a power cycle on the RV320, or a remote web interface reset if I'm unside the LAN, makes it work.
    Temporarily, then it crashes next day.

    I have the same settings, and the same up-to-date firmware.
    I see in the logs that the router incorrectly reports WAN2 as Up, then can't sync rate with it.
    Most of the time that failure is around the same time as the users report failure.
    But nothing is logged for WAN1 so it doesn't seem to be a physical failure in cabling, or the FTC converter feeding the router.
    2015-04-27, 10:33:35
    Kernel
    kernel: WAN [2] UP
    2015-04-27, 10:33:35
    Kernel
    kernel: [eth0] lanip=192.168.1.1, mask=255.255.255.0
    2015-04-27, 10:33:35
    Kernel
    kernel: ip[xxx.xxx.xx.xxx] mask[0.0.0.0]
    2015-04-27, 10:33:35
    Kernel
    kernel: ip[0.0.0.0] mask[0.0.0.0]
    2015-04-27, 10:33:36
    Kernel
    kernel: WAN [2] DOWN
    2015-04-27, 10:42:10
    Kernel
    kernel: WARNING: cant get external phy status
    2015-04-27, 10:42:11
    Kernel
    kernel: WARNING: no highest common denominator or auto-negotiation not complete
    2015-04-27, 10:42:11
    Kernel
    kernel: WARNING: no highest common denominator or auto-negotiation not complete
    2015-04-27, 10:58:01
    Kernel
    kernel: WARNING: no highest common denominator or auto-negotiation not complete
    2015-04-27, 10:58:02
    Kernel
    last message repeated 2 times
    2015-04-27, 10:58:02
    Kernel
    kernel: nk_bcm53115_sync_speeds_phy_to_mac(): sport[5], speed[0], duplex[0]
    2015-04-27, 10:58:03
    Kernel
    kernel: nk_bcm53115_sync_speeds_phy_to_mac(): sport[5], speed[1], duplex[2]

  • Using specific wan port for a particular domain/IP

    I have RV042 router which is connected to the internet by both the wan ports and I want to use it as a load balancer so that both of my internet connections can be utilized evenly. But now I have an issue in this scenario as my remote application gets logout whenever the communicating IP address changes.
    Now here is my question.
    Is there any way out so that I can specify the wan port used for a particular public IP address/domain name?

    Hi Kinshuk, thank you for using our forum, my name is Luis I am part of the Small business Support community. I read your post and I have an article from our knowledge base and called Guide me, you could use to configure a protocol binding in order to specify the WAN port that you want redirect and select the specific traffic.
    http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=622
    If you scroll down you will see a section called "Manage Protocol Binding" here you will see instructions to configure that.
    If you have any question please let me know.
    I hope you find this answer useful
    Greetings,
    Luis Arias.
    Cisco Network Support Engineer.

  • Rv320 - port forwarding from a specific WAN IP

    Hi, i just received and configuring the rv320 router. I can successfully set the port forwarding from WAN to specific LAN IP address. I would like to know is it possible for this device to set the port forwarding from a specific WAN IP address? Thank you for the help.

    I have the same problem, and have already tried creating a Access Rule without success. I need to forward Remote Desktop Port 3389 from a specific public IP address to a internal server. I do this with other lower-level Cisco Small Business routers all the time, but cannot get this to work with the RV320. Here's what I've tried:
    1) Create new Access Rule
    2) Create new Service called TS for TCP port 3389-3389
    3) Set new Access Rule to Allow
    4) Set Source Interface to Any (I've also tried WAN1, etc.)
    5) Set Source IP to the only single public IP that will be allowed
    6) Set Destination IP to the single internal IP address
    7) Set Scheduling to Always
    When I use any standard RDP app from the outside, the router blocks 3389 access.
    What am I missing? Can anyone help resolve this, or do I need to call in to Cisco Support?

  • RV320, specific traffic through specific wan port

    Hello all,
    I love the RV320, one of the best routers i've bought in years and it works like a charm with our Fiber connection on WAN1 and Coax Cable on WAN2.
    The only question I have right now, i know it is possible to sent specific traffic (DNS,HTTP etc) through specific WAN ports.
    But would it also be possible in some way to say *.website.com traffic will go through WAN port x only?
    Specific apps we use are only available through an IP coming from the provider we use on WAN2 (cable coax), so it would be handy if we could say that if app this or that and/or website is being called, auto serve it through WAN port x.
    Is this possible and if not, something cisco could  add?      

    Dear Michiel,
    Thank you for reaching Small Business Support Community.
    Besides the service management options available I do not see a particular feature to accomplish your needs. I work on this community forum as an analyst and I am going to mark this post as a business opportunity for improvement of the device.
    Thank you for your comment and please do not hesitate to reach me back if there is anything I may assist you with in the meantime.
    Kind regards,
    Jeffrey Rodriguez S. .:|:.:|:.
    Cisco Customer Support Engineer
    *Please rate the Post so other will know when an answer has been found.

  • I re-set password using specific user ID but when I put new password in it does not say incorrect password  it just spins and spins never accepting it.  What is the problem?

    I re-set password using specific user ID but when I put new password in it does not say incorrect password  it just spins and spins never accepting it.  What is the problem?

    Update on my problem connecting in Itunes with my Airport Express. Not sure if anything I tried made a difference
    but I finally got the Pop up window saying this device requires a Password. I entered the password and I can once again use the Airport Express as a remote speaker.

  • How to use BAPI_OBJCL* to set classification data for Techn. Objects - PM ?

    Good afternoon !
            I´m working in a project to integrate some legacy system with the ECC 6.0, and I need to do some activities like, create functional locations and equipments in SAP PM, I have done this creating Z RFC modules that call bapis like BAPI_FUNCLOC_CREATE and BAPI_EQUI_CREATE, but these BAPIs doesn´t fill classification data, so, in a first moment, I solved this using BDC, but I would like to solve these needs using standard BAPIs if possible.
            To solve the classification, I tried to do it using the BAPI_OBJCL* BAPIs(BAPI_OBJCL_GET_KEY_OF_OBJECT, BAPI_OBJCL_CREATE_KEY), but I didn´t find any example of using these bapis with technical objects, so I tried to test the BAPI_OBJCL_GET_KEY_OF_OBJECT in a first moment and, when I call it passing '003' as classtype(003 is the classtype for the functional locations), this bapi returns me "Class type 003 requires additional objects"(the same occurs if I try it with 002, for equipment). What means this message ? Need I to do some customization in img/spro, or cannot these bapis be used with PM technical objects ?
            Thank you for your attention,
            Wilson

    Hi all !
            I have found the solution for this problem, I found that I was trying to use the wrong functions for my case, so, to solve my needs here, I will use BAPI_OBJCL_CREATE to set the classification data for Functional Locations and Equipments, and I can use BAPI_OBJCL_GETCLASSES to list all classes assigned for a Technical Object, and BAPI_OBJCL_GETDETAIL to get all characteristics assigned to a Technical Object for a specific class.
            Thank you all for your attention !
            Wilson

  • Do I need to use specific printers with Macbook Pro?

    Do I need to use specific printers with Mac?

    Only those that provide compatible printer drivers.
    OS X- Printer and scanner software available for download
    OS X Mavericks- Set up a printer

  • Using the WAN port as a "LAN" port on the Airport Extreme Base Station...

    Hi everyone,
    I'm re-building my home wireless network and I'm doing so in preparation for the Slingbox AV I ordered last week. Here's my current setup:
    I have a DSL modem attached to an Airport Express (802.11n) in my office broadcasting my internet signal. I have an Airport Extreme Base Station (802.11g) set up in my living room as a WDS extender. I currently use the base station in my living room to connect the DishNetwork ViP722 DVR to the internet and allow me to set recordings remotely on my iPhone when I'm away from home. I use the LAN port on the base station to do this, and now with the Slingbox on the way (should be here early next week), I'm wondering what I need to do to make an internet connection available for the Slingbox AV.
    My question: Will I be able to simply use the WAN port as a "LAN" port since the Airport Extreme Base Station is being used as a WDS? It'd be awesome if the WAN port would become, essentially, a LAN port since it isn't being used.
    Thanks in advance for your advice and insight!

    slugoo wrote:
    My question: Will I be able to simply use the WAN port as a "LAN" port since the Airport Extreme Base Station is being used as a WDS? It'd be awesome if the WAN port would become, essentially, a LAN port since it isn't being used.
    I'd be surprised if that worked. The operation of an AirPort base station depends on keeping the WAN port and the LAN port(s) separate, as those normally are on two different networks.
    You might consider buying an Ethernet hub or switch, which would allow your AirPort Extreme's LAN port to be shared. Here's an example of an inexpensive one:
    http://www.bestbuy.com/site/olspage.jsp?skuId=7169244&st=ethernet+switch&type=pr oduct&id=1110266457435

  • SAPGUI (for Java) using with wan=true

    Hi all,
      I use java version of SAPGUI for linux. I've found a way how to integrate logon items into my system menu including client and username settings on logon screen: run guistart with conection string, e.g.
    path/to/gui/guistart '/H/192.168.1.1/S/3200&clnt=111&user=pvavra&wan=true'
      I use this way from SAPGUI version 6.30. With newer versions of SAPGUI I've found that some systems accept parameters to wrong position (I have to fill username to parameter clnt: clnt=pvavra to fill username). Later I've noted that no logon parameters are accepted when I use connect string with parameter wan=true.  Version 7.10 brings new feature: It write error mesage "Can't fill in logon data when using a wan connection".  Knows anybody why this way is imposible now? Is it an official policy of SAP or a bug? I usually need to connect over thin internet line to SAP systems and pre-filled logon screen is really comfortable feature. Does anybody know a workaround for such situation?

    So I fixed the problem.  In the VPN (PPTP) configuration, I had to:
    - Set the encryption from "Automatic" to "Maximum"
    - Click "Advanced" and check the box for "Send all traffic over VPN connection".
    Both of these selections were required.  You'd think "Automatic" would have been "automatic" about selecting the encryption level, but apparently it wasn't.
    It's unfortunate I have to send all traffic through the VPN as this slows or even prevents other internet-using applications to operate properly while I'm connected to the VPN.
    I think there's a way to edit a routing file and set it up in such a way to only have SAP use the VPN while the other applications bypass it, but I don't know how to do it and I don't really have time to learn it myself.
    Anyway, hope this helps people out there.  Thanks guys for weighing in with advice.
    Chris

  • How do I burn a dvd using the PAL setting for Europe?

    This is an older answer:
    Make a new project in PAL using custom settings. Copy and paste the contents from the NTSC project to the PAL project. Render everything.
    Don't do this unless you really need to. If you're making a DVD for Europe you don't need to.
    And my question is:
    Why is it not needed to change it to PAL if this DVD is for Europe?
    Would it not be best to use a project with PAL SD 720x576 DV Anamorphic  25i  ?
    What's the difference between .... x756 DV  and  ... DV Anamorphic
    and also completely without this DV and DV Anamorphic?

    Level 10(109,395 points)Tom WolskyJan 9, 2015 5:22 PM
    Re: How do I burn a dvd using the PAL setting?in response to Totti 10Why is it not needed to change it to PAL if this DVD is for Europe?
    You don't, unless you want to have PAL resolution. Would it not be best to use a project with PAL SD 720x576 DV Anamorphic  25i  ?
    Yes, if you want a PAL resolution DVD. That's why the OP is asking how to make a PAL project. What's the difference between .... x756 DV  and  ... DV Anamorphic
    DV is 4:3. DV Anamorphic is 16:9. and also completely without this DV and DV Anamorphic?
    Not sure what this means. The DVD specification is the same as DV resolution. If the OP as an HD project that has a frame rate of 23.98, the output resolution will be NTSC DV anamorphic, because DVD only accepts 23.98, 24, or 29.97 frame rates in 720x480, not in the PAL resolution 720x576. That has to be in 25fps.
    Like Show 0 Likes(0)
    Reply
    JUst to add the reason you don't need to make PAL for Europe is because all PAL DVDs can play back NTSC. Unfortunately almost no NTSC players can play back PAL.

  • Open Director with specific panel set

    Hi,
    It is possible to set the default configuration  of Director?
    In other words it is possible open Director with specific panel set?
    If yes how?
    Thanks.

    1. First, get the layout you want.
    2. Go to
    Edit > Preferences > General....
    3. Click the checkbox - Save Window Positions On Exit.
    4. Exit Director.
    5. Open Director and go back to the General Preferences and uncheck the Save Windows Position property.
    Now when you close Director, it won't save the positions and will used the last saved setup.
    Dean

  • PK constraint using specific tablespace

    How do I create primary key constraint using specific tablespace?
    I looked at PK properties in physical model but ‘Tablespace’ option under ‘Using Index’ tab is disabled.
    Thanks,
    Vikas

    Hi Vikas,
    The Tablespace property is disabled if the Using Index property on the General Tab of the Primary Key Property dialog is NO.
    So you first need to set the Using Index property to the relevant option.
    David

  • Message uses a character set that is not supported by the internet service

    Does any one have any advice on how to fix this problem?
    E-mails sent from my iphone 3G periodically arrive in an unreadable form at the recipient. The body of the e-mail has been replaced with the message "This message uses a character set that is not supported by the internet service...." The problem e-mails also include an attachment that contains an unformatted text file containing the original message surrounded by what appears to be lots of formatting data that is displayed as gibberish.
    This occurs sometimes, but not always, even with the same recipients. I am sending e-mail through a G-mail account that is configured on the iphone using IMAP. I have tried the gmail account to use the two available formatting options for mail, but neither fixes the problem.
    I have also upgraded to 2.01 and restored a few times without impact.

    Hi,
    I got somewhat similar problem with special charecters(German umlaud �,�,�..).
    I create a file with java having special charecters in it. Now if I open this file I am able to view the special charecters in it.But If I attach this file send it using following code then receiver can not see the umlaud charecters in it.They get replaced by _ or ?
    MimeBodyPart mbp2 = new MimeBodyPart();
    FileDataSource fds = new FileDataSource(fileName);
    mbp2.setDataHandler(new DataHandler(fds));
    mbp2.setFileName(output.getName());
    Multipart mp = new MimeMultipart();
    mp.addBodyPart(mbp2);
    msg.setContent(mp);
    Transport.send(msg);
    From you message it looks like you are able to send the mail attachment correctly(by preserving special charecters).
    Can you tell me what might be wrong in my code.
    I appriciate your efforts in advance.
    Prasad

  • HOW can I enter text using Japanese character sets?

    The "Text, Plates, Insets" section of the LOOKOUT(6.01) Help files states:
    "Click the » button to the right of the Text field to expand the field for multiple line entries. You can enter text using international character sets such as Chinese, Korean, and Japanese."
    Can someone please explain HOW to do this? Note, I have NO problem inputting Hirigana, Katakana, and Kanji into MS WORD; the keyboard emulates the Japanese layout and characters (Romaji is default) and the IME works fine converting Romaji, and I can also select charcters directly from the IME Pad. I have tried several different fonts with success and am currently using MS UI Gothic.ttf as default. Again, everything is normal and working in a predictable manner within Word.
    I cannot get these texts into Lookout. I can't cut/paste from HTML pages or from text editors, even though both display properly. Within Lookout with JP selected as language/keyboard, when trying to type directly into the text field, the IME CORRECTLY displays Hirigana until <enter> is pressed, at which point all text reverts to question marks (?? ???? ? ?????). If I use the IME Pad, it does pretty much the same. I managed to get the "Yen" symbol to display, though, if that's relevant. As I said, font selected (in text/plate font options) is MS UI Gothic with Japanese as the selected script. Oddly enough, at this point the "sample" window is showing me the exact Hirigana character I want displayed in Lookout, but it won't. I've also tried staying in English and copying unicode characters from the Windows Character Map. Same results (Yen sign works, Hirigana WON'T).
    Help me!
    JW_Tech

    JW_Tech,
    Have you changed the regional setting to Japanese?
    Doug M
    Applications Engineer
    National Instruments
    For those unfamiliar with NBC's The Office, my icon is NOT a picture of me
    Attachments:
    language.JPG ‏50 KB

Maybe you are looking for