RV320 VPN setup
Hello, I have Cisco RV320 dual WAN VPN router. I want to setup VPN connection to connect with my notebook remotely to my office network.
I have setup WAN1, SSL VPN with guide on youtube.com but I doesn´t work for me. My internet setup is for WAN1 IP 10.5.93.246, gateway 10.5.93.245, with DNS1 10.255.255.10 and DNS2 10.255.255.20. But my public IP is different for example 92.52.168.523.
I have done my setup exactly as in Cisco youtube guide, but it doesn´t work for me. When I try to open page https:\\92.52.168.523:10443 on my notebook I get error page not found.... But ping to my public IP adress (92.52.168.523) works fine
What could be the problem?
Thanks for your answer
Hello,
The issue that you are describing means that your modem is working as a router providing private IP addresses to your router.
What is happening now is that your modem has the Public IP 92.52.168.523 and your router, which is the device that has all the settings, has a private IP address of 10.5.93.246 not reachable over the internet. When you try to go to HTTPS://92.52.168.523:10443, you are actually reaching the modem and no the router. Thats why it is not working.
What you need to do is to contact your ISP and ask them to "bridge" the modem so that when you look at the IP address of WAN 1 inside the router you will see the actual public address and not the private: 10.5.93.246.
I hope this helps
Similar Messages
-
Hello Support,
I have a question regarding a remote access VPN setup with the following. I have a Cisco 6500 with multiple VLANs, and an FWSM setup in mutliple context mode. Each of our clients sits behind their own context, and has their own associated VLANs. Each context has a shared interface, so that one network (our management network) can see all of the networks. We are using a Cisco ASA to terminate P2P VPNs as the FWSms cannot do so, but I would like to setup a remote access VPN from the ASA, but I will need to connect in and have access to all networks. Currently the ASA has an outside interface for internet, two client inside interfaces, and one interface on the shared network.
If I setup a remote access VPN from the ASA with a separate scope will I be able to see all the networks that I setup routes and nonats for or is there more to it?
I provided a brief diagram showing all the vlans, I will need to be able to access all of the 6500s vlans when connected using the VPN.
Thanks in advance for all ideas, suggestions, and assistance.Hello John,
You will need to configure the respective IP Address pool for the Anyconnect users,
Then create the no_nat rules from all of the internal subnets to the Anyconnect Pool.
That should do it bud . I mean just make sure the internal network (core) knows that in order to reach the anyconnect pool must send the traffic to the ASA.
Rate all of the helpful posts!!!
Regards,
Jcarvaja
Follow me on http://laguiadelnetworking.com -
I think I have it working on my iPhone 5. But, I do not see how I can control the exit point that I would like for the VPN. Are all the exit points shown in the VPN setting now going to work with Open VPN, or do they remain PPTP? If I am reading correctly, they look like they remain PPTP. If I cannot control the exit point for open VPN, which exit point is the default in the profile you provided me?I note that Open VPN Connect does not work with any of the new 64 bit devices like the iPhone 5S, the iPad Air, and the new iPad MIni. Is there any chance that you guys will come up with an update for your app so that open VPN can be made to work on all iOS devices? That would be nice, particularly if the Open VPN Connect app does not give me a choice of exit points.Thanks,
I do not see where to enter IP addresses in the Open VPN setup. Also, how can I set it up so that I can choose different servers in the same way as I can currently choose them with my VPN app but for PPTP?
Just a quick note to tell you that Open VPN has updated their app so that it is compatible with 64 bit ARM devices like the iPhone 5S, the iPad Air, and the iPad Mini Retina.That does not resolve the problem of how to easily choose among the various possibilities for the exit server. We need to find an easy way to choose.Thank you for trying the new Firefox. I'm sorry that you’re unhappy with the new design.
I understand your frustration and surprise at the removal of these features but I can't undo these changes. I'm just a support volunteer and I do not work for Mozilla. But you can send any feedback about these changes to http://input.mozilla.org/feedback. Firefox developers collect data submitted through there then present it at the weekly Firefox meeting
I recommend you try to adjust to 29 and see if you can't make it work for you before you downgrade to a less secure and soon outdated version of Firefox.
Here are a few suggestions for restoring the old design. I hope you’ll find one that works for you:
*Use the [https://addons.mozilla.org/en-US/firefox/addon/classicthemerestorer/ Classic Theme Restorer] to bring back the old design. Learn more here: [[How to make the new Firefox look like the old Firefox]]
*Use the [https://addons.mozilla.org/en-US/firefox/addon/the-addon-bar/ Add-on Bar Restored] to bring back the add-on bar. Learn more here: [[What happened to the Add-on Bar?]] -
To run VPN setup my iphone is requesting for 4 digit pass code ... can you pls assisit?
Hello RozR,
We've an article that can help circumvent the new passcode and restore access to your iPhone.
iOS: Forgotten passcode or device disabled after entering wrong passcode
http://support.apple.com/kb/HT1212
Cheers,
Allen -
RV120W VPN Setup - basic help needed
Hi all,
I've recently bought a RV 120W Wireless-N VPN Firewall hoping it would ease me in creating VPN and remote connectivity. But I seems to be struggling with this.
Here is my situation.
When I bought my Cisco router I didn't know it had an ethernet port for WAN. I thought it would have a RJ11 compliant port. So now I am having to put the router behind my modem.
I gave my modem's LAN 192.168.2.1 and to RV120W I gave 192.168.2.2.
All PC's are not connected to internet via RV120W. For RV120W, the local IP network is 192.168.1.0. I've set 192.168.1.1 as the management IP of the Cisco RV120W. All the PC's can get internet from the above layout arrangement.
With frustration, I've portforwared all my ports on the modem (except 1 port) to RV120W i.e to IP 192.168.2.2.
If I enable PPTP on RV120W I can ping its port (1723 i remember) from outside. If I connect to port 80 from outside my network, I can get the managemnt interface of the RV120W.
With the help of the RV120W's userguide I managed to create VPN policy stuff via the 'basic VPN Setup' menu. The guides says to use a wizard but there is no wizard for VPN setup.
With that I have even created users (of every type) but I just can't make the connection.
When I use the QuickVPN to connect... its goes from "Connecting", "Activating Policy" again "Connecting" and then a big error saying a couple of things that might have caused the error.
I want to start from the beginning.
Can somebody please help me.
First... what I am I supposed to put in the fields of the following screenshot. Especially the fields "Remote WAN's IP Address", "Local WAN's IP Address" and "Local LAN IP Address".Once I knew about the bridge mode thing from this discussion, I started reading the manual of the modem in regard to the brigde mode setup.
According to the manual, the 'Data' bulb on the modem would be off if the modem is in bridge mode. and I've successfully put the modem on bridge mode I guess. It was pretty easy. I just deleted all the WAN setup rules/configs and began with the initial setup wizard which basically had the option to set the modem to bridge mode. After so, the 'Data' bulb got off meaning the modem is now in bridge mode. I am happy about that
But... still not done.
I put one ethernet cable into of the LAN ports of the modem and put the other end in RV120W WAN port. Logged into to RV120W, configured new PPPoE profile (I have the user and pass details) and attached it to the WAN internet setup config.
I went back to the dashboard of RV120W to see if WAN was up. It didn't. I gave some time. It didn't work. It says 'connecting' but never connects.
What am I doing wrong? Am I putting the cable between the modem and router the right way?
...and also, when the modem is in bridge mode will it forward all packets from lan to wan and vice versa or is it like forwarding packets to all ports once recieved.
(I am learning so much with this RV120W ) -
Simple VPN Setup Fails with "NOTIFY PROPOSAL_NOT_CHOSEN protocol"
Hi,
This is pulling my hair out! Must be overlooking something very simple!
Simple lab setup with 3 routers. VPN setup between R1 & R3 with static routing. R2 connects R1 & R3. All interfaces are reachable, including loopbacks. I am trying to encrypt traffic between loopback on R1 (69.69.69.69) to loopback on R3 (192.168.100.223).
With no Crypto Map applied to outgoing interfaces on R1 and R3 ping is successful (sourced via local loopback) between the loopbacks. As soon as I add the Crypto Map the same ping fails and and I get the following debug messages.
When ping initiated via outgoing interface, ping successful!
*Oct 6 11:44:26.121: ISAKMP: set new node 0 to QM_IDLE
*Oct 6 11:44:26.125: SA has outstanding requests (local 103.13.216.8 port 500, remote 103.13.215.236 port 500)
*Oct 6 11:44:26.129: ISAKMP:(1002): sitting IDLE. Starting QM immediately (QM_IDLE )
*Oct 6 11:44:26.133: ISAKMP:(1002):beginning Quick Mode exchange, M-ID of -1381344893
*Oct 6 11:44:26.137: ISAKMP:(1002):QM Initiator gets spi
*Oct 6 11:44:26.145: ISAKMP:(1002): sending packet to 172.1.1.1 my_port 500 peer_port 500 (I) QM_IDLE
*Oct 6 11:44:26.145: ISAKMP:(1002):Sending an IKE IPv4 Packet.
*Oct 6 11:44:26.149: ISAKMP:(1002):Node -1381344893, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
*Oct 6 11:44:26.153: ISAKMP:(1002):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
*Oct 6 11:44:26.301: ISAKMP (0:1002): received packet from 172.1.1.1 dport 500 sport 500 Global (I) QM_IDLE
*Oct 6 11:44:26.305: ISAKMP: set new node -1825528760 to QM_IDLE
*Oct 6 11:44:26.313: ISAKMP:(1002): processing HASH payload. message ID = -1825528760
*Oct 6 11:44:26.317: ISAKMP:(1002): processing NOTIFY PROPOSAL_NOT_CHOSEN protocol 3
spi 2376679447, message ID = -1825528760, sa = 670DD6A4
*Oct 6 11:44:26.317: ISAKMP:(1002): deleting spi 2376679447 message ID = -1381344893
*Oct 6 11:44:26.321: ISAKMP:(1002):deleting node -1381344893 error TRUE reason "Delete Larval"
*Oct 6 11:44:26.325: ISAKMP:(1002):deleting node -1825528760 error FALSE reason "Informational (in) state 1"
*Oct 6 11:44:26.329: ISAKMP:(1002):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Oct 6 11:44:26.329: ISAKMP:(1002):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
R1
crypto isakmp policy 1
authentication pre-share
crypto isakmp key cisco address 172.1.1.1
crypto ipsec transform-set TEST esp-3des esp-sha-hmac
crypto map CRYPTO 1 ipsec-isakmp
description IPSec Peer to R3
set peer 172.1.1.1
set transform-set TEST
match address ACL1
interface GigabitEthernet1/0
ip address 192.250.156.6 255.255.255.0
no ip route-cache cef
no ip route-cache
negotiation auto
crypto map CRYPTO
ip access-list extended ACL1
permit ip host 69.69.69.69 host 192.168.100.223
R1#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id slot status
172.1.1.1 192.250.156.6 QM_IDLE 1002 0 ACTIVE
R3
crypto isakmp policy 1
authentication pre-share
crypto isakmp key cisco address 192.250.156.6
crypto ipsec transform-set TEST esp-3des esp-sha-hmac
crypto map TEST 1 ipsec-isakmp
description Primary IPSec Peer to R1
set peer 192.250.156.6
set transform-set TEST
match address ACL1
interface GigabitEthernet1/0
ip address 172.1.1.1 255.255.255.0
no ip route-cache cef
no ip route-cache
negotiation auto
crypto map CRYPTO
ip access-list extended ACL1
permit ip host 192.168.100.223 host 69.69.69.69
R3#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id slot status
172.1.1.1 192.250.156.6 QM_IDLE 1002 0 ACTIVE
Any help appreciated,
Thanks.Hi Paul,
"processing NOTIFY PROPOSAL_NOT_CHOSEN protocol 3" indicates the remote VPN peer rejected the phase 2 proposal.
The configuration snippet you have shared here seems fine, ISAKMP and IPSec debugs (debug crypto isakmp and debug crypto ipsec) from the remote VPN peer will be helpful in troubleshooting further.
Following is a useful doc on VPN troubleshooting:
IPsec Troubleshooting: Understanding and Using debug Commands
Cheers,
Rudresh V -
Hello
The RV320 logs are very poor to troubleshoot VPN issues, even with external syslog facility, at the maximum log level the device does not log any VPN event.
Is there a way to increase the log level?
Is there a separate syslog facility local# for VPN?
Where to get extensive documentation about syslog facilities numbers used by RV320?
Thank youCisco support team is trying to fix this up, but it's not working
They managed to build a working tunnel but that's not the point, we need VPN logs, period.
It looks like the device only starts VPN log after a succesfull VPN connection, making the device impossible to setup, diagnose or monitor failed VPN connections. This is a no go.
using external syslog does not help, the only VPN related output I get in log is :
Oct 22 12:32:18 10.0.0.254 VPN Log: [g2gips0]: [Tunnel Disconnected]
what I should get (and is a must have) would be :
2014-10-20, 05:15:31
VPN Log
[g2gips2] #11: [Tunnel Established] ISAKMP SA established
2014-10-20, 05:15:54
VPN Log
[g2gips2] #14: [Tunnel Established] sent MR3, ISAKMP SA established
2014-10-20, 05:15:55
VPN Log
[g2gips2]: cmd=up-client peer=62.176.126.28 peer_client=192.168.1.0/24 peer_client_net=192.168.1.0 peer_client_mask=255.255.255.0
2014-10-20, 05:15:55
VPN Log
ip route add 192.168.1.0/24 via 88.161.221.254 dev eth1 metric 35
2014-10-20, 05:15:55
VPN Log
iptables -t nat -I vpn -s 10.0.0.0/24 -d 192.168.1.0/24 -j ACCEPT
2014-10-20, 05:15:55
VPN Log
iptables -t nat -I vpn -s 192.168.1.0/24 -d 10.0.0.0/24 -j ACCEPT
2014-10-20, 05:15:55
VPN Log
iptables -t nat -I vpn_postrouting -s 10.0.0.0/24 -d 192.168.1.0/24 -j ACCEPT
2014-10-20, 05:15:55
VPN Log
iptables -t nat -I vpn_postrouting -o eth0 -s 192.168.1.0/24 -d 10.0.0.0/24 -j ACCEPT
2014-10-20, 05:15:55
VPN Log
[g2gips2] #15: [Tunnel Established] IPsec SA established {ESP=>0xc570a9c8 < 0xc43d09ba}
2014-10-20, 05:16:53
VPN Log
[g2gips2] #15: [Tunnel Negotiation Fail] DPD: Could not find newest phase 1 state
2014-10-20, 05:26:44
User Log
User cisco Session Expired
2014-10-20, 06:14:42
VPN Log
[g2gips2] #16: [Tunnel Established] sent MR3, ISAKMP SA established
2014-10-20, 06:14:42
VPN Log
[g2gips2] #17: [Tunnel Established] IPsec SA established {ESP=>0xc0931255 < 0xc928b34e}
2014-10-20, 06:14:42
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc570a9c8) not found (maybe expired)
2014-10-20, 07:13:34
VPN Log
[g2gips2] #18: [Tunnel Established] IPsec SA established {ESP=>0xcea6223a < 0xcfbc92ba}
2014-10-20, 07:13:34
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc0931255) not found (maybe expired)
2014-10-20, 08:12:20
VPN Log
[g2gips2] #19: [Tunnel Established] IPsec SA established {ESP=>0xcdb2138d < 0xcfa80369}
2014-10-20, 08:12:20
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcea6223a) not found (maybe expired)
2014-10-20, 09:11:09
VPN Log
[g2gips2] #20: [Tunnel Established] IPsec SA established {ESP=>0xc5aeba36 < 0xcd182a7c}
2014-10-20, 09:11:09
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcdb2138d) not found (maybe expired)
2014-10-20, 10:09:57
VPN Log
[g2gips2] #21: [Tunnel Established] IPsec SA established {ESP=>0xc862dbe2 < 0xc68a5a29}
2014-10-20, 10:09:57
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc5aeba36) not found (maybe expired)
2014-10-20, 11:08:45
VPN Log
[g2gips2] #22: [Tunnel Established] IPsec SA established {ESP=>0xc8c5d191 < 0xc7009873}
2014-10-20, 11:08:45
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc862dbe2) not found (maybe expired)
2014-10-20, 12:07:29
VPN Log
[g2gips2] #23: [Tunnel Established] IPsec SA established {ESP=>0xcbb5aca6 < 0xc087d294}
2014-10-20, 12:07:29
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc8c5d191) not found (maybe expired)
2014-10-20, 13:06:16
VPN Log
[g2gips2] #24: [Tunnel Established] IPsec SA established {ESP=>0xce08b895 < 0xca8ee98b}
2014-10-20, 13:06:16
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcbb5aca6) not found (maybe expired)
2014-10-20, 14:05:03
VPN Log
[g2gips2] #25: [Tunnel Established] IPsec SA established {ESP=>0xc84ace20 < 0xc66ee4e5}
2014-10-20, 14:05:03
VPN Log
[g2gips2] #16: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xce08b895) not found (maybe expired)
2014-10-20, 14:13:46
VPN Log
[g2gips2] #26: [Tunnel Established] sent MR3, ISAKMP SA established
2014-10-20, 15:03:54
VPN Log
[g2gips2] #27: [Tunnel Established] IPsec SA established {ESP=>0xc8808731 < 0xc6aaaf12}
2014-10-20, 15:03:54
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc84ace20) not found (maybe expired)
2014-10-20, 16:02:47
VPN Log
[g2gips2] #28: [Tunnel Established] IPsec SA established {ESP=>0xc20db40f < 0xcbcbb7c5}
2014-10-20, 16:02:47
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc8808731) not found (maybe expired)
2014-10-20, 17:01:39
VPN Log
[g2gips2] #29: [Tunnel Established] IPsec SA established {ESP=>0xc8f8b88c < 0xc87177ac}
2014-10-20, 17:01:39
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc20db40f) not found (maybe expired)
2014-10-20, 18:00:24
VPN Log
[g2gips2] #30: [Tunnel Established] IPsec SA established {ESP=>0xc24edeb7 < 0xc31180a7}
2014-10-20, 18:00:24
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc8f8b88c) not found (maybe expired)
2014-10-20, 18:59:12
VPN Log
[g2gips2] #31: [Tunnel Established] IPsec SA established {ESP=>0xcf388896 < 0xcca051f9}
2014-10-20, 18:59:12
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc24edeb7) not found (maybe expired)
2014-10-20, 19:57:59
VPN Log
[g2gips2] #32: [Tunnel Established] IPsec SA established {ESP=>0xcb12a9c8 < 0xc6d3e8a4}
2014-10-20, 19:57:59
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcf388896) not found (maybe expired)
2014-10-20, 20:56:46
VPN Log
[g2gips2] #33: [Tunnel Established] IPsec SA established {ESP=>0xcdc041c8 < 0xc69fa232}
2014-10-20, 20:56:46
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcb12a9c8) not found (maybe expired)
2014-10-20, 21:55:36
VPN Log
[g2gips2] #34: [Tunnel Established] IPsec SA established {ESP=>0xc4f97df6 < 0xc4a67abd}
2014-10-20, 21:55:36
VPN Log
[g2gips2] #26: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcdc041c8) not found (maybe expired)
2014-10-20, 22:12:56
VPN Log
[g2gips2] #35: [Tunnel Established] sent MR3, ISAKMP SA established
2014-10-20, 22:54:27
VPN Log
[g2gips2] #36: [Tunnel Established] IPsec SA established {ESP=>0xc3716585 < 0xc41ab42b}
2014-10-20, 22:54:27
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc4f97df6) not found (maybe expired)
2014-10-20, 23:53:13
VPN Log
[g2gips2] #37: [Tunnel Established] IPsec SA established {ESP=>0xcfc747c8 < 0xc5994856}
2014-10-20, 23:53:13
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc3716585) not found (maybe expired)
2014-10-21, 00:51:58
VPN Log
[g2gips2] #38: [Tunnel Established] IPsec SA established {ESP=>0xcf4ea957 < 0xc566c6d3}
2014-10-21, 00:51:58
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcfc747c8) not found (maybe expired)
2014-10-21, 01:50:48
VPN Log
[g2gips2] #39: [Tunnel Established] IPsec SA established {ESP=>0xc4f4ddc5 < 0xc852f0a8}
2014-10-21, 01:50:48
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcf4ea957) not found (maybe expired)
2014-10-21, 02:49:33
VPN Log
[g2gips2] #40: [Tunnel Established] IPsec SA established {ESP=>0xc4d14f63 < 0xc841322e}
2014-10-21, 02:49:33
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc4f4ddc5) not found (maybe expired)
2014-10-21, 03:48:17
VPN Log
[g2gips2] #41: [Tunnel Established] IPsec SA established {ESP=>0xcab61c1d < 0xc8e06d65}
2014-10-21, 03:48:17
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc4d14f63) not found (maybe expired)
2014-10-21, 04:47:10
VPN Log
[g2gips2] #42: [Tunnel Established] IPsec SA established {ESP=>0xcc4d0867 < 0xc5370a2f}
2014-10-21, 04:47:10
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcab61c1d) not found (maybe expired)
2014-10-21, 05:45:57
VPN Log
[g2gips2] #43: [Tunnel Established] IPsec SA established {ESP=>0xcb8459a9 < 0xcab43b24}
2014-10-21, 05:45:57
VPN Log
[g2gips2] #35: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcc4d0867) not found (maybe expired)
2014-10-21, 06:12:00
VPN Log
[g2gips2] #44: [Tunnel Established] sent MR3, ISAKMP SA established
2014-10-21, 06:44:47
VPN Log
[g2gips2] #45: [Tunnel Established] IPsec SA established {ESP=>0xc1d633d9 < 0xc5b9214f}
2014-10-21, 06:44:47
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xcb8459a9) not found (maybe expired)
2014-10-21, 07:43:37
VPN Log
[g2gips2] #46: [Tunnel Established] IPsec SA established {ESP=>0xc8a6235e < 0xc549a18d}
2014-10-21, 07:43:37
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc1d633d9) not found (maybe expired)
2014-10-21, 08:42:28
VPN Log
[g2gips2] #47: [Tunnel Established] IPsec SA established {ESP=>0xc563592a < 0xc033e13d}
2014-10-21, 08:42:28
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc8a6235e) not found (maybe expired)
2014-10-21, 09:41:12
VPN Log
[g2gips2] #48: [Tunnel Established] IPsec SA established {ESP=>0xc6c5e0b6 < 0xc9acd1e2}
2014-10-21, 09:41:12
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc563592a) not found (maybe expired)
2014-10-21, 10:40:03
VPN Log
[g2gips2] #49: [Tunnel Established] IPsec SA established {ESP=>0xc49d311a < 0xca8961e8}
2014-10-21, 10:40:03
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc6c5e0b6) not found (maybe expired)
2014-10-21, 11:38:53
VPN Log
[g2gips2] #50: [Tunnel Established] IPsec SA established {ESP=>0xc682b92b < 0xc01e3e5f}
2014-10-21, 11:38:53
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc49d311a) not found (maybe expired)
2014-10-21, 12:37:41
VPN Log
[g2gips2] #51: [Tunnel Established] IPsec SA established {ESP=>0xc0e9d4eb < 0xc0c1b26a}
2014-10-21, 12:37:41
VPN Log
[g2gips2] #44: [Tunnel Authorize Fail] ignoring Delete SA payload: PROTO_IPSEC_ESP SA(0xc682b92b) not found (maybe expired)
2014-10-21, 13:36:29
VPN Log
[g2gips2] #52: [Tunnel Established] IPsec SA established {ESP=>0xc424276a < 0xc0467e19} -
I setup the RV320 and am using the USB1 interface until I get my permanent WAN interface ordered. I can get to the internet with no issues. I setup EasyVPN and PPTP but cannot get access remotely into the VPN. I setup an access rule to allow ALL traffic from USB1 into the network. I also created a user in the User management page.
When trying to connect with the Cisco VPN Client I get the following in the router log file:
Aug 1 13:42:04 2013
VPN Log
packet from 70.155.120.114:22520: [Tunnel Authorize Fail] no connection has been authorized with policy=PSK+AGGRESSIVE+XAUTHPSK+XAUTHSERVER
Aug 1 13:42:04 2013
Connection Accepted
IN=ppp3000 OUT= MAC= SRC=70.155.120.114 DST=166.156.174.130 DMAC=45:00:03:7f:95:8c SMAC=00:00:6d:11:a0:b5 LEN=895 TOS=0x00 PREC=0x00 TTL=109 ID=38284 PROTO=UDP SPT=22520 DPT=500 LEN=875
When trying to connect via PPTP I get the following error at the client:
Error 678: The remote computer did not respond.
What am I missing?
Does the USB1 interface allow remote access?
ThanksJust an update. Finally on my 3rd RV320 I was able to get the current firmware loaded w/o the unit locking up. I used XP instead of Win7 this time just in case that was the problem.
I did get the SSL VPN to function over the USB1 modem. No luck still with EasyVPN or PPTP.
My SSL VPN drops me into VLAN4 with address of 192.168.4.x. I can PCAnywhere to a PC on that VLAN and from there get to devices on VLAN3 (192.168.3.x) which is my mgmt VLAN by creating some access rules for that one PC we connect remotely into.
I've tried various rules to let me get directly to the mgmt VLAN direct from the remote PC but have not had any luck. Any thoughts on what to try? I have InterVLAN routing turned on for VLAN3 and VLAN4. I need access to devices on both VLANs so it's not just a matter of changing the SSL remote users ip to 192.168.3.x. -
Issues with basic VPN setup and split tunneling
I have created an SSL VPN to a CISCO ASA 8.6 running ASDM 6.6.
Im able to connect to the VPN and reach all the devices with the LAN but Im not able to browse the web. When I enable the split tunnel Im able to browse the web but then Im not able to reach any internal device.
Here is part of the show run:
object network RedInterna
subnet 150.211.101.0 255.255.255.0
description Red Interna
object network NETWORK_OBJ_10.4.1.0_28
subnet 10.4.1.0 255.255.255.240
access-list inside_access_in extended permit ip object RedInterna any
access-list VPN_INTERNET standard permit 150.211.101.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool VPN_POOL 10.4.1.1-10.4.1.14 mask 255.255.255.240
failover
failover lan unit secondary
failover lan interface fail-1 GigabitEthernet0/2
failover key *****
failover interface ip fail-1 10.3.1.21 255.255.255.252 standby 10.3.1.22
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-66114.bin
asdm history enable
arp timeout 14400
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.4.1.0_28 NETWORK_OBJ_10.4.1.0_28 no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 187.217.68.145 1
route inside 10.0.0.0 255.0.0.0 10.1.1.78 1
route inside 150.211.0.0 255.255.0.0 10.1.1.78 1
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-3.1.00495-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_VPN_ internal
group-policy GroupPolicy_VPN_ attributes
wins-server none
dns-server value 8.8.8.8
vpn-tunnel-protocol ssl-client
default-domain value dominio.com.mx
tunnel-group VPN_ type remote-access
tunnel-group VPN_ general-attributes
address-pool VPN_POOL
default-group-policy GroupPolicy_VPN_
tunnel-group VPN_ webvpn-attributes
group-alias VPN_ enable
I´m not sure if Im missing some small details or setup. Any help will be highly appreciated.
Thanks!!!Hi,
When you are using Full Tunnel VPN (which is the default setting) you will have a couple of things that you need to configure on the ASA.
First, the ASA by default won't allow traffic to enter through an interface and then leave through that same interface. This is what essentially happens when the traffic from the VPN Client comes to the ASA and then heads out to the Internet. In your case the traffic comes through the "outside" and leaves through the "outside" interface.
You will need this command
same-security-traffic permit intra-interface
You can check if its enabled at the moment with the command
show run same-security-traffic
Second, the VPN users will need to have NAT configuration just like any LAN users behind the actual ASA. So you will essentially have to configure Dynamic PAT for traffic from "outside" to "outside"
You can accomplish that with the following configuration
object network VPN-PAT
subnet 10.4.1.0 255.255.255.240
nat (outside,outside) dynamic interface
I would imagine that this should do it for you to be able to connect to the Internet and to the LAN network when the VPN is active.
Hope this helps
Let me know how it goes.
- Jouni -
I have installed Snow Leopard Server on a new XServe. I have updated to 10.6.2.
Other services are working Related to VPN I have configured the VPN Service using L2TP.
I have no additional network routing defined.
Every time I try to setup a connection (from my macbook pro --> running snow leopard 10.6.2) I get the following log messages:
2009-11-15 14:44:41 CET Incoming call... Address given to client = 192.168.1.160
Sun Nov 15 14:44:41 2009 : Directory Services Authentication plugin initialized
Sun Nov 15 14:44:41 2009 : Directory Services Authorization plugin initialized
Sun Nov 15 14:44:41 2009 : L2TP incoming call in progress from '192.168.1.15'...
Sun Nov 15 14:44:41 2009 : L2TP received SCCRQ
Sun Nov 15 14:44:41 2009 : L2TP sent SCCRP
Sun Nov 15 14:44:41 2009 : L2TP received SCCCN
Sun Nov 15 14:44:41 2009 : L2TP received ICRQ
Sun Nov 15 14:44:41 2009 : L2TP sent ICRP
Sun Nov 15 14:44:41 2009 : L2TP received ICCN
Sun Nov 15 14:44:41 2009 : L2TP connection established.
Sun Nov 15 14:44:41 2009 : using link 0
Sun Nov 15 14:44:41 2009 : Using interface ppp0
Sun Nov 15 14:44:41 2009 : Connect: ppp0 <--> socket[34:18]
Sun Nov 15 14:44:41 2009 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : lcp_reqci: returning CONFACK.
Sun Nov 15 14:44:41 2009 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : sent [LCP EchoReq id=0x0 magic=0x7dd4d1cd]
Sun Nov 15 14:44:41 2009 : sent [EAP Request id=0x1 Identity ]
Sun Nov 15 14:44:41 2009 : rcvd [LCP EchoReq id=0x0 magic=0x1e217556]
Sun Nov 15 14:44:41 2009 : sent [LCP EchoRep id=0x0 magic=0x7dd4d1cd]
Sun Nov 15 14:44:41 2009 : rcvd [LCP EchoRep id=0x0 magic=0x1e217556]
Sun Nov 15 14:44:41 2009 : rcvd [EAP Response id=0x1 Identity <"]
Sun Nov 15 14:44:47 2009 : LCP terminated by peer (Failed to authenticate ourselves to peer)
Sun Nov 15 14:44:47 2009 : sent [LCP TermAck id=0x2]
Sun Nov 15 14:44:47 2009 : L2TP received CDN
Sun Nov 15 14:44:47 2009 : Connection terminated.
Sun Nov 15 14:44:47 2009 : L2TP disconnecting...
Sun Nov 15 14:44:47 2009 : L2TP sent CDN
Sun Nov 15 14:44:47 2009 : L2TP sent StopCCN
Sun Nov 15 14:44:47 2009 : L2TP disconnected
2009-11-15 14:44:47 CET --> Client with address = 192.168.1.160 has hungup
What does that mean:
"Failed to authenticate ourselves to peer" ???
Are there some configurations which can solve this problem ???
Best regards
AndreasThis are the related client side log entries:
Sun Nov 15 14:44:40 2009 : L2TP connecting to server '192.168.1.10' (192.168.1.10)...
Sun Nov 15 14:44:40 2009 : IPSec connection started
Sun Nov 15 14:44:40 2009 : IPSec phase 1 client started
Sun Nov 15 14:44:40 2009 : IPSec phase 1 server replied
Sun Nov 15 14:44:41 2009 : IPSec phase 2 started
Sun Nov 15 14:44:41 2009 : IPSec phase 2 established
Sun Nov 15 14:44:41 2009 : IPSec connection established
Sun Nov 15 14:44:41 2009 : L2TP sent SCCRQ
Sun Nov 15 14:44:41 2009 : L2TP received SCCRP
Sun Nov 15 14:44:41 2009 : L2TP sent SCCCN
Sun Nov 15 14:44:41 2009 : L2TP sent IRCQ
Sun Nov 15 14:44:41 2009 : L2TP received ICRP
Sun Nov 15 14:44:41 2009 : L2TP sent ICCN
Sun Nov 15 14:44:41 2009 : L2TP connection established.
Sun Nov 15 14:44:41 2009 : using link 0
Sun Nov 15 14:44:41 2009 : Using interface ppp0
Sun Nov 15 14:44:41 2009 : Connect: ppp0 <--> socket[34:18]
Sun Nov 15 14:44:41 2009 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : lcp_reqci: returning CONFACK.
Sun Nov 15 14:44:41 2009 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
Sun Nov 15 14:44:41 2009 : sent [LCP EchoReq id=0x0 magic=0x1e217556]
Sun Nov 15 14:44:41 2009 : rcvd [LCP EchoReq id=0x0 magic=0x7dd4d1cd]
Sun Nov 15 14:44:41 2009 : sent [LCP EchoRep id=0x0 magic=0x1e217556]
Sun Nov 15 14:44:41 2009 : rcvd [EAP Request id=0x1 Identity ]
Sun Nov 15 14:44:41 2009 : sent [EAP Response id=0x1 Identity <"]
Sun Nov 15 14:44:47 2009 : Connection terminated.
Sun Nov 15 14:44:47 2009 : rcvd [EAP Request id=0x2 EAP KRB <00003f000001000101>]
Sun Nov 15 14:44:47 2009 : L2TP disconnecting...
Sun Nov 15 14:44:47 2009 : L2TP sent CDN
Sun Nov 15 14:44:47 2009 : L2TP sent StopCCN
Sun Nov 15 14:44:47 2009 : L2TP disconnected -
Hi,
I am using OS X server (10.9.1). I try to setup VPN service. But, I do not know what went wrong. Below is the log. Any tips?
1st time: I use wwmm.wwmmhome.private...
2013-12-31 14:23:19 SGT Incoming call... Address given to client = 192.168.1.240Tue Dec 31 14:23:19 2013 : Directory Services Authentication plugin initialized
Tue Dec 31 14:23:19 2013 : Directory Services Authorization plugin initialized
Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:23:19 2013 : PPTP incoming call in progress from '183.90.37.225'...
Tue Dec 31 14:23:19 2013 : PPTP connection established.
Tue Dec 31 14:23:19 2013 : using link 0
Tue Dec 31 14:23:19 2013 : Using interface ppp0
Tue Dec 31 14:23:19 2013 : Connect: ppp0 <--> socket[34:17]
Tue Dec 31 14:23:19 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
Tue Dec 31 14:23:19 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:19 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:23:19 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:23:22 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : sent [LCP EchoReq id=0x0 magic=0x729c77b1]
Tue Dec 31 14:23:22 2013 : sent [CHAP Challenge id=0xd5 <663e256443001f6c0163674232734908>, name = "wwmm.wwmmhome.private"]
Tue Dec 31 14:23:22 2013 : rcvd [LCP EchoReq id=0x0 magic=0x38d3186b]
Tue Dec 31 14:23:22 2013 : sent [LCP EchoRep id=0x0 magic=0x729c77b1]
Tue Dec 31 14:23:22 2013 : rcvd [LCP EchoRep id=0x0 magic=0x38d3186b]
Tue Dec 31 14:23:22 2013 : rcvd [CHAP Response id=0xd5 <63847a83bdb04f9fba56d82397d7213e00000000000000003d68f95fbd5d9f5e90ad10d4e8403c f53e5940402f913a6b00>, name = "test"]
Tue Dec 31 14:23:22 2013 : sent [CHAP Failure id=0xd5 ""]
Tue Dec 31 14:23:22 2013 : CHAP peer authentication failed for walter
Tue Dec 31 14:23:22 2013 : sent [LCP TermReq id=0x2 "Authentication failed"]
Tue Dec 31 14:23:22 2013 : Connection terminated.
Tue Dec 31 14:23:22 2013 : PPTP disconnecting...
Tue Dec 31 14:23:22 2013 : PPTP disconnected
2013-12-31 14:23:22 SGT --> Client with address = 192.168.1.240 has hung up
2nd time, I use wwmm.dyndns.org
2013-12-31 14:38:38 SGT Incoming call... Address given to client = 192.168.1.240Tue Dec 31 14:38:38 2013 : Directory Services Authentication plugin initialized
Tue Dec 31 14:38:38 2013 : Directory Services Authorization plugin initialized
Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:38:38 2013 : PPTP incoming call in progress from '183.90.37.225'...
Tue Dec 31 14:38:39 2013 : PPTP connection established.
Tue Dec 31 14:38:39 2013 : using link 0
Tue Dec 31 14:38:39 2013 : Using interface ppp0
Tue Dec 31 14:38:39 2013 : Connect: ppp0 <--> socket[34:17]
Tue Dec 31 14:38:39 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
Tue Dec 31 14:38:39 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:39 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:38:39 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:38:42 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : sent [LCP EchoReq id=0x0 magic=0x5b1829ce]
Tue Dec 31 14:38:42 2013 : sent [CHAP Challenge id=0x5a <4a753b2e091d155a1414337d40401750>, name = "wwmm.dyndns.org"]
Tue Dec 31 14:38:42 2013 : rcvd [LCP EchoReq id=0x0 magic=0x3298b0f1]
Tue Dec 31 14:38:42 2013 : sent [LCP EchoRep id=0x0 magic=0x5b1829ce]
Tue Dec 31 14:38:42 2013 : rcvd [LCP EchoRep id=0x0 magic=0x3298b0f1]
Tue Dec 31 14:38:42 2013 : rcvd [CHAP Response id=0x5a <2f54770187524125079b5d74e01b09e800000000000000004359e904d9814bc5e0eb4bb880e7e5 23181a0d22b9164e2400>, name = "test"]
Tue Dec 31 14:38:42 2013 : DSAuth plugin: unsupported authen authority: recved ShadowHash;HASHLIST:<SALTED-SHA512,SMB-NT,CRAM-MD5,RECOVERABLE,SALTED-SHA512-PB KDF2>, want ApplePasswordServer
Tue Dec 31 14:38:42 2013 : DSAuth plugin: MPPE key required, but its retrieval failed.
Tue Dec 31 14:38:42 2013 : sent [CHAP Failure id=0x5a "S=8DDCFFC7EA287D3A141E5594392BCBD87C35F76B M=Access granted"]
Tue Dec 31 14:38:42 2013 : CHAP peer authentication failed for walter
Tue Dec 31 14:38:42 2013 : sent [LCP TermReq id=0x2 "Authentication failed"]
Tue Dec 31 14:38:42 2013 : Connection terminated.
Tue Dec 31 14:38:42 2013 : PPTP disconnecting...
Tue Dec 31 14:38:42 2013 : PPTP disconnected
2013-12-31 14:38:42 SGT --> Client with address = 192.168.1.240 has hungupThe VPN server in Server.app is these days pretty feeble, it only does PPTP and L2TP and does not support using security certificates or VPN on demand. (Which requires security certificates.) As a result the security of Apples VPN server is only capable of functions which have all been successfully cracked. Now for most people that might not be too much of a concern but if your a law, health, finance, or government customer then it should be a concern.
However...
While the VPN server itself does not support clustering nor in fact do any of the services in Server.app there might be a way to achieve what you want. If you have a DNS load-balancer then you can point all the clients to the load-balancer and it will distribute the requests to two or more Apple VPN servers. You just need to make sure each Apple VPN server gives out a different range of IP addresses with no overlaps. -
Can any one please advise me I am trying to set up a VPN on my PIX 501 and for some reason it is not working. I have posted the scrips below. If someone can advise me what I need to change that would be great.
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password P@55w0rd! encrypted
passwd P@55w0rd! encrypted
hostname CFSLXAKALAZ
domain-name akademic.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 192.168.2.0 VPN
object-group service RemoteDesktop tcp
port-object range 3389 3389
access-list inside_access_in remark Allow all outbound UDP port 53 for DNS
access-list inside_access_in permit udp any any eq domain
access-list inside_access_in remark Allow ping to any external IP
access-list inside_access_in permit icmp any any
access-list inside_access_in remark Allow all outbound TCP connections
access-list inside_access_in permit tcp any any
access-list outside_access_in remark Allow external DNS via UDP
access-list outside_access_in permit udp any eq domain any
access-list outside_access_in remark Allow ping from outside to inside
access-list outside_access_in permit icmp any any
access-list outside_access_in remark Remote Desktop to any internal IP
access-list outside_access_in permit tcp any any object-group RemoteDesktop
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 10.20.58.30 255.255.255.0
ip address inside 192.168.2.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool donkpool 192.168.2.50-192.168.2.60
pdm location 10.20.58.0 255.255.255.0 outside
pdm location 192.168.2.0 255.255.255.0 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route outside 0.0.0.0 0.0.0.0 10.20.58.1 1
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 10.20.58.0 255.255.255.0 outside
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
vpngroup donk address-pool donkpool
vpngroup donk idle-time 1800
vpngroup donk password P@55w0rd!
telnet 10.20.58.30 255.255.255.0 outside
telnet 192.168.2.0 255.255.255.0 inside
telnet timeout 5
ssh 10.20.58.0 255.255.255.0 outside
ssh 192.168.2.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.128-192.168.2.252 inside
dhcpd dns 158.152.1.58
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
terminal width 80
terminal width 80You are missing a lot of config, depending on what type of vpn you are trying to setup please follow the links below to complete it:
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/ipsecint.html
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/basclnt.html -
Hi,
I've successfully setup generic ikev2 vpn profile on my z10 and made it to auto connect over mobile network, and link it with my wifi.
Now here is something that I don't understand :
1. On the VPN screen, it says tap profile to edit. It won't happen, and tapping it will always pop up error to connect. Need to click edit and tap.
2. If mobile is switch off, vpn will never be activated even wifi is on and connected to the net. Seems like vpn can only be used when cellular is active.
3. There is no way to tell whether the vpn is active or not other than going back into the setting.
Is this being done on purpose?Hey DingDang,
To edit the connection you must select Edit at the bottom first, clicking on the profile attempts to connect your VPN.
To see if you are connected, open Network Connections> VPN will say Connected, you can also check the status by selecting the three dots and choose View Status Details.
Do you have a firewall on the Wi-Fi network?This may be why it is not connecting when you are on Wi-Fi only.
Thanks.
-HB
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)! -
Can someone interpret this vpn setup directions?
http://vpn.bcc.bilkent.edu.tr/mac/
this is my school's website with the instructions about how to setup the vpn. but im using mountain lion and somehow all my attempts are failing. and options in mountain lion are not the same with the pictures in the website. I think there is no problem with the vpn server because I used it with a pc before.Hello TimmyCoogs21,
I may not be able to give you a direct answer on this. I am not sure of your familiarity with log files. PID refers to a Proceess ID. I am not sure which process has an ID of 94 that is causing you this non-sleep issue. Others have had similar issues in the past, i.e.The HIDD after could possibly mean it is some form of Human Interface Device. If you have a USB or something plugged into your mac at night, or a faulty hardware piece entirely. (These are just speculations)
Bluetooth drivers prevent system from sleeping in Mavericks - what's going on!?
Do not let the title fool you as he states that it is not a problem that is caused by bluetooth. Ultimately he sought support from apple, which in your case, I would do the same.
You could restore/refresh your system and see if this continues if not I would recommend seeking apple support.
I know this does not fix your problem, however I hope you find some help in it.
Cheers. -
Hi,
I've got the following issue regarding connecting to a Checkpoint VPN in windows 8.1:
Message from VPN App: [test]
Connect: System.Exception: Failed to communicate with the server.
at CheckPointVpnPluginAppBg.CCC.cccPost(VpnChannel channel, String data, Certificate clientCert, Int32 retryCount)
at CheckPointVpnPluginAppBg.CCC.cccConnect(VpnChannel channel, Boolean authNeeded)
at CheckPointVpnPluginAppBg.CCC.snxConnect(VpnChannel channel, StreamSocket socket, VpnRouteAssignment& routeScope, VpnNamespaceAssignment& nameScope)
at CheckPointVpnPluginAppBg.VpnPlugin.Connect(VpnChannel channel)
HRESULT 80131500 System.Exception
What does this mean?
When I setup the connection and add my certificate, It connects to the server, then I need to supply a password. I get a result back from the server.
But when it's trying to establish a VPN it gives this error.Hi,
According to your description, let us know your version of Checkpoint VPN.
Meanwhile, considering that the issue should be related to Checkpoint VPN ,and it is a third-party software, I suggest you contact Checkpoint VPN support for help.
https://forums.checkpoint.com/forums/index.jspa
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Regards,
Kelvin hsu
TechNet Community Support
Maybe you are looking for
-
Photoshop CC 2014 not responding and cannot uninstall
PS CC 2014 installed on Mac. Recent update stopped at 74% days ago. Tried to stop update and now it says "finishing" for the last 2 days. PS CC 2014 won't open at all. Tried to uninstall it and Adobe Creative Cloud but I keep getting a message th
-
Hi mate I bought a new Ipad.I trying to update but service is dosn't working.can you help me please.
-
Dear All, We have a requirement : In multi level release strategy if, PR/PO is rejected at any level, it should trigger derelease at all the previous levels and E mail notification to be sent to all the levels. We are trying with the help of work fl
-
Documentation Assistant - No Logical Component exists for this analysis
Hi Whe trying to create a analysis with in solution manager documentation assistant i get the error messaage No logical component exists for this analysis , verify the analysis project. Can anyone tell me how i can solve this, Thanks Barry
-
After installing MobileMe System Panel, Mail Quits on Launch
sigh Does anyone have any suggestions? I am not the brightest techno in the bunch, so try to be gentle. Here is the error text from the console application: Process: Mail [803] Path: /Applications/Mail.app/Contents/MacOS/Mail Identifier: com.apple.ma