Rvs 4000 dynamic ip and static dns

hello
I just want to know if its possible to use static dns (those of opendns) when my internet provider connect me through dynamic IP?
i am using the last firmware 1.3.0.5
thank you for your help ?
bolbix

With this router model, there is not the option to use custom dns on the wan if your getting your ip address dynamically. In order to implement the static dns you would need to implement a static ip address on this router. However any of the rv042, rv082 and rv016 routers will allow that function. Hopefully this helps you out Jerbol.

Similar Messages

Dynamic PAT and Static NAT issue ASA 5515

Hi All,
Recently we migrated our network to ASA 5515, since we had configured nat pool overload on our existing router the users are able to translated their ip's outside. Right now my issue was when I use the existing NAT configured to our router into firewall, it seems that the translation was not successful actually I used Dynamic NAT. When I use the Dynamic PAT(Hide) all users are able to translated to the said public IP's. I know that PAT is Port address translation but when I use static nat for specific server. The Static NAT was not able to translated. Can anyone explain if there's any conflict whit PAT to Static NAT? I appriciate their response. Thanks!
- Bhal

Hi,
I would have to guess that you Dynamic PAT was perhaps configured as a Section 1 rule and Static NAT configured as Section 2 rule which would mean that the Dynamic PAT rule would always override the Static NAT for the said host.
The very basic configured for Static NAT and Default PAT I would do in the following way
object network STATIC
host
nat (inside,outside) static dns
object-group network DEFAULT-PAT-SOURCE
network-object
nat (inside,outside) after-auto source dynamic DEFAULT-PAT-SOURCE interface
The Static NAT would be configured as Network Object NAT (Section 2) and the Default PAT would be configured with Twice NAT / Manual NAT (after-auto specifies it as Section 3 rule)
This might sound confusing. Though it would be easier to say what the problem is if we saw the actual NAT configuration. Though I gave the reason that I think is probably one of the most likely reasons if there is some conflict with the 2 NAT rules
You can also check out a NAT document I made regarding the new NAT configuration format and its operation.
https://supportforums.cisco.com/docs/DOC-31116
Hope this helps
- Jouni

WRT600N and static DNS

On my old WRT54G, if I setup a static DNS server to point to my local Linux box, that's what all my DHCP clients get. However, I've noticed that on WRT600N, my DHCP clients are pushed the addresses of my ISP DNS servers (two of them), followed by WRT600N local IP address, followd by the static DNS address I configured.
On example, here's what my DHCP clients were sent by WRT54G:
192.168.0.3
Here's what WRT600N (configured exactly the same as WRT54G was) sends to them:
68.87.76.178
68.87.78.130
192.168.0.1
192.168.0.3
Obviously, this is bad. If I configured the static DNS address, then I obviously have a reason for doing so, and that address should be the only one (or at least the first one) that DHCP clients will get (otherwise, there's not much point in having that option in router's configuration). Is there any way to force WRT600N to behave like WRT54G used to?

maui29111 wrote:
you cannot just assign a static DNS server on the router, because the DNS server that it's sending is valid and from your isp itself, if evcer you have a static account from isp then that's the time where you can force the router to use a static ip address
Actually, no. Even if you are using DHCP to obtain an IP address, there is nothing preventing you from configuring DNS servers manually (using static DNS servers). DHCP is not all or nothing. You are free to use DHCP to obtain IP address, and override addresses of DNS servers (or any other info).
Here's an example of such usage. Linksys router acts as Internet gataway (using DHCP to obtain external IP address from ISP). It also acts as DHCP server for local clients. I have a DNS server on my local network. This DNS server is used to resovle the names of the hosts on my local network, and it also acts as caching DNS to resolve names of the hosts on the Internet. Hence, I do not wish Linksys router to send my ISP's DNS server to clients on local network. I want it to send the address of my local DNS server.
On WRT54G this configuration was possible. You just enter static addresses of your DNS server, and it would send those to the DHCP client, instead of forwarding ISP's DNS servers. WRT600N doesn't allow this type of configuration.

PCI-6542 card for dynamic genration and static control

Hello
I am using only one PCI -6542 card. I want to use few channels for dynamic signal. These are control signals for the ADC. While the conversion is in progress I want to use remaining signals for switching relays for measurement.
Application requirements are as follows.
Channel 0-14 are for dynamic genration for giving control signal to ADC.
Channel 15-31 are for static control bits for relays.
Requirement is pattern should be running continiously and parallely I shoud able to switch the ralay. It can be in any order and any seqence as per the demand.
Thanks and Reards
Amol

Hello
I can able to solve this problem. For your referance I have attached here the code. Which works for this.
Thanks and Regards
Amol
Attachments:
application.vi ‏65 KB

Dynamic varibles and Static Varibles

I have this table row with these data element in it........I
want to be able to change the text of my data elements and when i
write them to a file they are changed when i view the
file......Right now if i change the value in the text field it
still writes the data from the database to the file.......Do i need
to change the ouput to the name instead of the values????? Any help
on this would be great....

If you display the form and the values from the database are
shown, you are on the right track. When a user makes a change in
the content of a text box and clicks the submit button, the action
page declared in the <FORM> tag is loaded. The name/value
pair of each text box is available in the action page. Use these
values to update your database.

Setting Static DNS on E4200

I recently wanted to try using the Google public DNS servers on my home network. I have a Cisco E4200 router.
On the router's administration page, I set Static DNS 1 to 8.8.8.8 and Static DNS 2 to 8.8.4.4 and saved the settings.
Even after rebooting the router, the Setup page shows the Google DNS addresses listed above, but the Status page shows 65.32.5.111 and 65.32.5.112 as being the DNS servers its using.
Does anyone know how to set the E4200 to use different DNS servers?
Thanks!

Thanks. I ran the analyzer and in the direct probing of dns resolvers section, it showed this:
Your system is configured to use 1 DNS resolver(s).
The resolver at 192.168.1.1 (tampfl-dns-cac-112) could not process the following tested types: [snipped]
192.168.1.1 is, of course, my router's local IP address.

No Internet Access with Static IP and RVS 4000

I have an RVS 4000. I have several PC's to which I have assigned static IP addresses. I have recently upgraded most of the PC's to Win 7 (64) machines. I updated the firmware on the RVS4000 to 1.3.3.5 in conjunction with this. After such update (and actually before as well) I could not assign a static IP address to a PC and have access to the internet. It connects fine to my LAN, just no internet access. This is also affected on several other machines running Win XP and Win 2003 Server, so it's not just this computer.
I have:
     1. Shut down (powered off/unplugged) everything, router, DSL modem, switches, server, etc.
     2. As I said firmware is current.
     3. Yes, DNS servers and gateway, subnet, etc. are all correctly specified on the PC.
     4. Router is set for gateway mode.
     5. Set to only IPV4.
The only way it allows internet access is to use DHCP. I've even tried taking the IP address via DHCP and manually assigning the DNS servers and that works fine, but as soon as I assign a static IP internet access is immediately gone.
There must be something I'm missing, but I can't seem to find it.
Everything worked fine prior to the conversion of the Win 7 machines, i.e. I had several PC's with static IP's and no problems.
Any thoughts appreciated.

As an addendum, if I turn off the Firewall (internet access policy to disable) it will allow the static IP computer to have internet access. I have the DHCP range set to be .5 - .54 and am using a static ip outside this range. The Internet access policy is to restrict those PC's getting IP via DHCP.

Dynamic file request to appserver and static file request to webserver

Can we redirect dynamic file request to appserver and static file request to webserver in any application and
what are the best way to do it ?
Waiting for the best suggestions ?

when you have a large number of images/css/javascript/static(html/pdf/doc) files. It takes some of the processing load from your app server and also reduces the network traffic (otherwise traffic must flow between webserver and weblogic as well). it is also reasonably trivial to configure cache/modification/etags headers from a webserver and they are probably more featured than a weblogic server (e.g. to turn on gzip for static files dynamic is just a setting in the webserver but probably needs a custom filter developed in weblogic).
Again this applies if you already have a webserver (normally because your firewall policy dictates this approach). If you are considering whether to have a webserver at all then there are different considerations.
regards
deepak

Dynamic release strategy and static release strategy

Hi,
What is the difference between dynamic release strategy and static release strategy.
What the customization setting required to activate dymanic and static release strategy.
Thank you
REgards,
Yshu

Dear Yshu,
What do you mean by dynamic and static release strategy. In SAP, we don'y have this term.
Please kindly give more explanation so we can help you.
We only have with classification and without classification.
Normally, release strategy without classification is used in R/2, and out of support in
R/3. However the functionality still available in case you want to use it.
You can not use Release without classification and Release with classification.
If there is an entry present in Release Group table (T16FG-FRGOT), only release with
classification can be used.
If you are in R/3, then forget the release strategy without classification but just
use the release strategy with classification as it had more flexibility than the old
system design.
Thanks
Ian

MS NLB with ASA and Static NAT from PUP to NLB IP

Hi all,
I am trying to get MS NLB up and running. It is almost all working. Below is my physical setup.
ASA 5510 > Cat 3750X >2x ESXi 5.1 Hosts > vSwitch > Windows 2012 NLB Guest VMs.
I have two VMs runing on two different ESXi hosts. They have two vNICs. One for managment and one for inside puplic subnet. The inside puplic subnet NICs are in the NLB cluster. The inside public subnet is NATed on the ASA to a outide public IP.
192.168.0.50 is the 1st VM
192.168.0.51 is the 2nd VM
192.168.0.52 is the cluster IP for heartbeat
192.168.0.53 is the cluster IP for NLB traffic.
0100.5e7f.0035 is the cluster MAC.
The NLB cluster is using MULTICAST
I have read the doumentation for both the ASA and CAT switch for adding a static ARP using the NLB IP and NLB MAC.
For the ASA I found
http://www.cisco.com/en/US/docs/security/asa/asa84/asdm64/configuration_guide/mode_fw.html#wp1226249
ASDM
Configuration > Device Management > Advanced > ARP > ARP Static Table
I was able to add my stic ARP just fine.
However, the next step was to enable ARP inspection.
Configuration > Device Management > Advanced > ARP > ARP Inspection
My ASDM does not list ARP Inspection, only has the ARP Static Table area. Not sure about this.
For the CAT Switch I found
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example09186a0080a07203.shtml
I added the both the ARP and Static MAC. For the static MAC I used the VLAN ID of the inside public subnet and the interfaces connected to both ESXi hosts.
On the ASA I added a static NAT for my outside Public IP to my inside pupblic NLB IP and vise versa. I then added a DNS entry for our domain to point to the outside public IP. I also added it to the public servers section allowing all IP traffic testing puproses.
At any rate the MS NLB is working ok. I can ping both the Public IP and the Inside NLB IP just fine from the outside. (I can ping the inside NLB IP becuase I'm on a VPN with access to my inside subnets) The problem is when I go to access a webpade from my NLB servers using the DNS or the Public IP I get a "This Page Can't Be Displyed" messgae. Now while on the VPN if I use the same URL but insied use the NLB IP and not the Public IP it works fine.
So I think there is soemthing wrong with the NATing of the Public to NLB IP even tho I can ping it fine. Below is my ASA Config. I have bolded the parts of Interest.
Result of the command: "show run"
: Saved
ASA Version 8.4(4)9
hostname MP-ASA-1
enable password ac3wyUYtitklff6l encrypted
passwd ac3wyUYtitklff6l encrypted
names
dns-guard
interface Ethernet0/0
nameif outside
security-level 0
ip address 198.XX.XX.82 255.255.255.240
interface Ethernet0/1
description Root Inside Interface No Vlan
speed 1000
duplex full
nameif Port-1-GI-Inside-Native
security-level 100
ip address 10.1.1.1 255.255.255.0
interface Ethernet0/1.2
description Managment LAN 1 for Inside Networks
vlan 2
nameif MGMT-1
security-level 100
ip address 192.168.180.1 255.255.255.0
interface Ethernet0/1.3
description Managment LAN 2 for Inside Networks
vlan 3
nameif MGMT-2
security-level 100
ip address 192.168.181.1 255.255.255.0
interface Ethernet0/1.100
description Development Pubilc Network 1
vlan 100
nameif DEV-PUB-1
security-level 50
ip address 192.168.0.1 255.255.255.0
interface Ethernet0/1.101
description Development Pubilc Network 2
vlan 101
nameif DEV-PUB-2
security-level 50
ip address 192.168.2.1 255.255.255.0
interface Ethernet0/1.102
description Suncor Pubilc Network 1
vlan 102
nameif SUNCOR-PUB-1
security-level 49
ip address 192.168.3.1 255.255.255.0
interface Ethernet0/1.103
description Suncor Pubilc Network 2
vlan 103
nameif SUNCOR-PUB-2
security-level 49
ip address 192.168.4.1 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
boot system disk0:/asa844-9-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network Inside-Native-Network-PNAT
subnet 10.1.1.0 255.255.255.0
description Root Inisde Native Interface Network with PNAT
object network ASA-Outside-IP
host 198.XX.XX.82
description The primary IP of the ASA
object network Inside-Native-Network
subnet 10.1.1.0 255.255.255.0
description Root Inisde Native Interface Network
object network VPN-POOL-PNAT
subnet 192.168.100.0 255.255.255.0
description VPN Pool NAT for Inside
object network DEV-PUP-1-Network
subnet 192.168.0.0 255.255.255.0
description DEV-PUP-1 Network
object network DEV-PUP-2-Network
subnet 192.168.2.0 255.255.255.0
description DEV-PUP-2 Network
object network MGMT-1-Network
subnet 192.168.180.0 255.255.255.0
description MGMT-1 Network
object network MGMT-2-Network
subnet 192.168.181.0 255.255.255.0
description MGMT-2 Network
object network SUNCOR-PUP-1-Network
subnet 192.168.3.0 255.255.255.0
description SUNCOR-PUP-1 Network
object network SUNCOR-PUP-2-Network
subnet 192.168.4.0 255.255.255.0
description SUNCOR-PUP-2 Network
object network DEV-PUB-1-Network-PNAT
subnet 192.168.0.0 255.255.255.0
description DEV-PUB-1-Network with PNAT
object network DEV-PUB-2-Network-PNAT
subnet 192.168.2.0 255.255.255.0
description DEV-PUB-2-Network with PNAT
object network MGMT-1-Network-PNAT
subnet 192.168.180.0 255.255.255.0
description MGMT-1-Network with PNAT
object network MGMT-2-Network-PNAT
subnet 192.168.181.0 255.255.255.0
description MGMT-2-Network with PNAT
object network SUNCOR-PUB-1-Network-PNAT
subnet 192.168.3.0 255.255.255.0
description SUNCOR-PUB-1-Network with PNAT
object network SUNCOR-PUB-2-Network-PNAT
subnet 192.168.4.0 255.255.255.0
description SUNCOR-PUB-2-Network with PNAT
object network DEV-APP-1-PUB
host 198.XX.XX.XX
description DEV-APP-2 Public Server IP
object network DEV-APP-2-SNAT
host 192.168.2.120
description DEV-APP-2 Server with SNAT
object network DEV-APP-2-PUB
host 198.XX.XX.XX
description DEV-APP-2 Public Server IP
object network DEV-SQL-1
host 192.168.0.110
description DEV-SQL-1 Inside Server IP
object network DEV-SQL-2
host 192.168.2.110
description DEV-SQL-2 Inside Server IP
object network SUCNOR-APP-1-PUB
host 198.XX.XX.XX
description SUNCOR-APP-1 Public Server IP
object network SUNCOR-APP-2-SNAT
host 192.168.4.120
description SUNCOR-APP-2 Server with SNAT
object network SUNCOR-APP-2-PUB
host 198.XX.XX.XX
description DEV-APP-2 Public Server IP
object network SUNCOR-SQL-1
host 192.168.3.110
description SUNCOR-SQL-1 Inside Server IP
object network SUNCOR-SQL-2
host 192.168.4.110
description SUNCOR-SQL-2 Inside Server IP
object network DEV-APP-1-SNAT
host 192.168.0.120
description DEV-APP-1 Network with SNAT
object network SUNCOR-APP-1-SNAT
host 192.168.3.120
description SUNCOR-APP-1 Network with SNAT
object network PDX-LAN
subnet 192.168.1.0 255.255.255.0
description PDX-LAN for S2S VPN
object network PDX-Sonicwall
host XX.XX.XX.XX
object network LOGI-NLB--SNAT
host 192.168.0.53
description Logi NLB with SNAT
object network LOGI-PUP-IP
host 198.XX.XX.87
description Public IP of LOGI server for NLB
object network LOGI-NLB-IP
host 192.168.0.53
description LOGI NLB IP
object network LOGI-PUP-SNAT-NLB
host 198.XX.XX.87
description LOGI Pup with SNAT to NLB
object-group network vpn-inside
description All inside accessible networks
object-group network VPN-Inside-Networks
description All Inside Nets for Remote VPN Access
network-object object Inside-Native-Network
network-object object DEV-PUP-1-Network
network-object object DEV-PUP-2-Network
network-object object MGMT-1-Network
network-object object MGMT-2-Network
network-object object SUNCOR-PUP-1-Network
network-object object SUNCOR-PUP-2-Network
access-list acl-vpnclinet extended permit ip object-group VPN-Inside-Networks any
access-list outside_access_out remark Block ping to out networks
access-list outside_access_out extended deny icmp any any inactive
access-list outside_access_out remark Allow all traffic from inside to outside networks
access-list outside_access_out extended permit ip any any
access-list outside_access extended permit ip any object LOGI-NLB--SNAT
access-list outside_access extended permit ip any object SUNCOR-APP-2-SNAT
access-list outside_access extended permit ip any object SUNCOR-APP-1-SNAT
access-list outside_access extended permit ip any object DEV-APP-2-SNAT
access-list outside_access extended permit ip any object DEV-APP-1-SNAT
access-list outside_cryptomap extended permit ip object-group VPN-Inside-Networks object PDX-LAN
pager lines 24
logging asdm informational
mtu outside 1500
mtu Port-1-GI-Inside-Native 1500
mtu MGMT-1 1500
mtu MGMT-2 1500
mtu DEV-PUB-1 1500
mtu DEV-PUB-2 1500
mtu SUNCOR-PUB-1 1500
mtu SUNCOR-PUB-2 1500
mtu management 1500
ip local pool Remote-VPN-Pool 192.168.100.1-192.168.100.20 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any Port-1-GI-Inside-Native
icmp permit any MGMT-1
icmp permit any MGMT-2
icmp permit any DEV-PUB-1
icmp permit any DEV-PUB-2
icmp permit any SUNCOR-PUB-1
icmp permit any SUNCOR-PUB-2
asdm image disk0:/asdm-649-103.bin
no asdm history enable
arp DEV-PUB-1 192.168.0.53 0100.5e7f.0035 alias
arp timeout 14400
no arp permit-nonconnected
nat (Port-1-GI-Inside-Native,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (DEV-PUB-1,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (DEV-PUB-2,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (MGMT-1,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (MGMT-2,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (SUNCOR-PUB-1,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (SUNCOR-PUB-2,outside) source static any any destination static VPN-POOL-PNAT VPN-POOL-PNAT
nat (DEV-PUB-1,outside) source static DEV-PUP-1-Network DEV-PUP-1-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
nat (DEV-PUB-2,outside) source static DEV-PUP-2-Network DEV-PUP-2-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
nat (MGMT-1,outside) source static MGMT-1-Network MGMT-1-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
nat (MGMT-2,outside) source static MGMT-2-Network MGMT-2-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
nat (Port-1-GI-Inside-Native,outside) source static Inside-Native-Network Inside-Native-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
nat (SUNCOR-PUB-1,outside) source static SUNCOR-PUP-1-Network SUNCOR-PUP-1-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
nat (SUNCOR-PUB-2,outside) source static SUNCOR-PUP-2-Network SUNCOR-PUP-2-Network destination static PDX-LAN PDX-LAN no-proxy-arp route-lookup
object network Inside-Native-Network-PNAT
nat (Port-1-GI-Inside-Native,outside) dynamic interface
object network VPN-POOL-PNAT
nat (Port-1-GI-Inside-Native,outside) dynamic interface
object network DEV-PUB-1-Network-PNAT
nat (DEV-PUB-1,outside) dynamic interface
object network DEV-PUB-2-Network-PNAT
nat (DEV-PUB-2,outside) dynamic interface
object network MGMT-1-Network-PNAT
nat (MGMT-1,outside) dynamic interface
object network MGMT-2-Network-PNAT
nat (MGMT-2,outside) dynamic interface
object network SUNCOR-PUB-1-Network-PNAT
nat (SUNCOR-PUB-1,outside) dynamic interface
object network SUNCOR-PUB-2-Network-PNAT
nat (SUNCOR-PUB-2,outside) dynamic interface
object network DEV-APP-2-SNAT
nat (DEV-PUB-2,outside) static DEV-APP-2-PUB
object network SUNCOR-APP-2-SNAT
nat (SUNCOR-PUB-2,outside) static SUNCOR-APP-2-PUB
object network DEV-APP-1-SNAT
nat (DEV-PUB-1,outside) static DEV-APP-1-PUB
object network SUNCOR-APP-1-SNAT
nat (SUNCOR-PUB-1,outside) static SUCNOR-APP-1-PUB
object network LOGI-NLB--SNAT
nat (DEV-PUB-1,outside) static LOGI-PUP-IP
object network LOGI-PUP-SNAT-NLB
nat (outside,DEV-PUB-1) static LOGI-NLB-IP
access-group outside_access in interface outside
access-group outside_access_out out interface outside
route outside 0.0.0.0 0.0.0.0 198.145.120.81 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 outside
http 10.1.1.0 255.255.255.0 Port-1-GI-Inside-Native
http 192.168.180.0 255.255.255.0 MGMT-1
http 192.168.100.0 255.255.255.0 Port-1-GI-Inside-Native
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect icmp error
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:d6f9f8e2113dc03cede9f2454dba029b
: end
Any help would be great! I think the issue is in teh NAT as I am able to access NLB IP from the outside and could not do that before adding the Static ARP stuff.
Thanks,
Chris

Also If I change to NAT from the public IP to the NLB IP to use either one of the phsyical IPs of the NLB cluster (192.168.0.50 or 51) it works fine when using the public IP. So it's definatly an issue when NATing the VIP of NLB cluster.
Chris

RVS 4000 HTTP mgmt interface hangs @ Port 80 & DHCP stops working

This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
Internet connection is DHCP
LAN is set to DHCP with several Static devices defined
DMZ is dsabled
Functionining as a gateway
Time is set via NTP & the NRC
IPV4 Only
Everything is pretty much dedault except for QoS
Trust mode is Port, set to 4, 4, 4, 1
( Port 4 has a Linksys ATA plugged into it for VOIP services )
SIP Port Forwarding is enabled for 5060
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.
When this happens the only remedy is to power reboot.
Everthing comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.
My next step is to setuo a syslog server and have the logs copied out.
Anyone see this kind of behavior before ?
Any ideas ??
( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
Thanks Derek

Hi there Vijay !
I cannot upgrade to that version of Firmware as my RVS4000 is a V1, not a V2.
Is there some way I can change it such that it will load the newer Firmware ?
This is the error I receive when trying to upgrade anyway :
"Upgrade file is not the correct type or version for this device.
Upgrade failed.
Please obtain the correct file and try again."
Otherwise the newest firmware I can load is 1.3.3.5
( which seems to have this problem )

Resolve.conf, dnsmasq and external DNS servers

I am using dnsmasq to filter out ad urls, so my /etc/resolv.conf looks like that:
# Generated by dhcpcd from wlan0
nameserver 127.0.0.1
domain home
nameserver 192.168.1.254
# /etc/resolv.conf.tail can replace this line
However, it looks like after getting through the url filtration layer of dnsmasq, the URLs are being resolved by a DNS sever of whatever Access Point I am connected to. This create problems, because they often render me unable to connect to services like sourceforge.net, etc.
So, instead of that, I would like my system to fall back to Google and OpenDNS after filtering urls through dnsmasq.
But how can I do that? This is a specific case and wiki does not cover it.
Last edited by Lockheed (2013-05-19 16:50:43)

$ cat /etc/resolv.conf
# Generated by dhcpcd from wlan0
nameserver 127.0.0.1
nameserver 8.8.8.8
domain home
# /etc/resolv.conf.tail can replace this line
The google DNS is what I put in there earlier to be able to use internet after dnsmasq stopped starting.
$ cat /etc/resolvconf.conf
# Configuration for resolvconf(8)
# See resolvconf.conf(5) for details
resolv_conf=/etc/resolv.conf
# If you run a local name server, you should uncomment the below line and
# configure your subscribers configuration files below.
name_servers=127.0.0.1
# Write out dnsmasq extended configuration and resolv files
dnsmasq_conf=/etc/dnsmasq-conf.conf
dnsmasq_resolv=/etc/dnsmasq-resolv.conf
$ cat /etc/dnsmasq.conf
# Configuration file for dnsmasq.
# Format is one option per line, legal options are the same
# as the long options legal on the command line. See
# "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details.
# Listen on this specific port instead of the standard DNS port
# (53). Setting this to zero completely disables DNS function,
# leaving only DHCP and/or TFTP.
#port=5353
# The following two options make you a better netizen, since they
# tell dnsmasq to filter out queries which the public DNS cannot
# answer, and which load the servers (especially the root servers)
# unnecessarily. If you have a dial-on-demand link they also stop
# these requests from bringing up the link unnecessarily.
# Never forward plain names (without a dot or domain part)
#domain-needed
# Never forward addresses in the non-routed address spaces.
#bogus-priv
# Uncomment this to filter useless windows-originated DNS requests
# which can trigger dial-on-demand links needlessly.
# Note that (amongst other things) this blocks all SRV requests,
# so don't use it if you use eg Kerberos, SIP, XMMP or Google-talk.
# This option only affects forwarding, SRV records originating for
# dnsmasq (via srv-host= lines) are not suppressed by it.
#filterwin2k
# Change this line if you want dns to get its upstream servers from
# somewhere other that /etc/resolv.conf
#resolv-file=/etc/resolv-dnsmasq.conf
# By default, dnsmasq will send queries to any of the upstream
# servers it knows about and tries to favour servers to are known
# to be up. Uncommenting this forces dnsmasq to try each query
# with each server strictly in the order they appear in
# /etc/resolv.conf
strict-order
# If you don't want dnsmasq to read /etc/resolv.conf or any other
# file, getting its servers from this file instead (see below), then
# uncomment this.
#no-resolv
# If you don't want dnsmasq to poll /etc/resolv.conf or other resolv
# files for changes and re-read them then uncomment this.
#no-poll
# Add other name servers here, with domain specs if they are for
# non-public domains.
#server=/localnet/192.168.0.1
server=208.67.222.222
server=208.67.220.220
# Example of routing PTR queries to nameservers: this will send all
# address->name queries for 192.168.3/24 to nameserver 10.1.2.3
#server=/3.168.192.in-addr.arpa/10.1.2.3
# Add local-only domains here, queries in these domains are answered
# from /etc/hosts or DHCP only.
#local=/localnet/
# Add domains which you want to force to an IP address here.
# The example below send any host in double-click.net to a local
# web-server.
#address=/double-click.net/127.0.0.1
# --address (and --server) work with IPv6 addresses too.
#address=/www.thekelleys.org.uk/fe80::20d:60ff:fe36:f83
# You can control how dnsmasq talks to a server: this forces
# queries to 10.1.2.3 to be routed via eth1
# server=10.1.2.3@eth1
# and this sets the source (ie local) address used to talk to
# 10.1.2.3 to 192.168.1.1 port 55 (there must be a interface with that
# IP on the machine, obviously).
# [email protected]#55
# If you want dnsmasq to change uid and gid to something other
# than the default, edit the following lines.
#user=
#group=
# If you want dnsmasq to listen for DHCP and DNS requests only on
# specified interfaces (and the loopback) give the name of the
# interface (eg eth0) here.
# Repeat the line for more than one interface.
#interface=lo
# Or you can specify which interface _not_ to listen on
#except-interface=
# Or which to listen on by address (remember to include 127.0.0.1 if
# you use this.)
#listen-address=127.0.0.1
# If you want dnsmasq to provide only DNS service on an interface,
# configure it as shown above, and then use the following line to
# disable DHCP and TFTP on it.
#no-dhcp-interface=
# On systems which support it, dnsmasq binds the wildcard address,
# even when it is listening on only some interfaces. It then discards
# requests that it shouldn't reply to. This has the advantage of
# working even when interfaces come and go and change address. If you
# want dnsmasq to really bind only the interfaces it is listening on,
# uncomment this option. About the only time you may need this is when
# running another nameserver on the same machine.
#bind-interfaces
# If you don't want dnsmasq to read /etc/hosts, uncomment the
# following line.
#no-hosts
# or if you want it to read another file, as well as /etc/hosts, use
# this.
addn-hosts=/etc/hosts.block
#hostsfile=/etc/hosts.block
# Set this (and domain: see below) if you want to have a domain
# automatically added to simple names in a hosts-file.
#expand-hosts
# Set the domain for dnsmasq. this is optional, but if it is set, it
# does the following things.
# 1) Allows DHCP hosts to have fully qualified domain names, as long
# as the domain part matches this setting.
# 2) Sets the "domain" DHCP option thereby potentially setting the
# domain of all systems configured by DHCP
# 3) Provides the domain part for "expand-hosts"
#domain=thekelleys.org.uk
# Set a different domain for a particular subnet
#domain=wireless.thekelleys.org.uk,192.168.2.0/24
# Same idea, but range rather then subnet
#domain=reserved.thekelleys.org.uk,192.68.3.100,192.168.3.200
# Uncomment this to enable the integrated DHCP server, you need
# to supply the range of addresses available for lease and optionally
# a lease time. If you have more than one network, you will need to
# repeat this for each network on which you want to supply DHCP
# service.
#dhcp-range=192.168.0.50,192.168.0.150,12h
# This is an example of a DHCP range where the netmask is given. This
# is needed for networks we reach the dnsmasq DHCP server via a relay
# agent. If you don't know what a DHCP relay agent is, you probably
# don't need to worry about this.
#dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h
# This is an example of a DHCP range which sets a tag, so that
# some DHCP options may be set only for this network.
#dhcp-range=set:red,192.168.0.50,192.168.0.150
# Use this DHCP range only when the tag "green" is set.
#dhcp-range=tag:green,192.168.0.50,192.168.0.150,12h
# Specify a subnet which can't be used for dynamic address allocation,
# is available for hosts with matching --dhcp-host lines. Note that
# dhcp-host declarations will be ignored unless there is a dhcp-range
# of some type for the subnet in question.
# In this case the netmask is implied (it comes from the network
# configuration on the machine running dnsmasq) it is possible to give
# an explicit netmask instead.
#dhcp-range=192.168.0.0,static
# Enable DHCPv6. Note that the prefix-length does not need to be specified
# and defaults to 64 if missing/
#dhcp-range=1234::2, 1234::500, 64, 12h
# Do Router Advertisements, BUT NOT DHCP for this subnet.
#dhcp-range=1234::, ra-only
# Do Router Advertisements, BUT NOT DHCP for this subnet, also try and
# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack
# hosts. Use the DHCPv4 lease to derive the name, network segment and
# MAC address and assume that the host will also have an
# IPv6 address calculated using the SLAAC alogrithm.
#dhcp-range=1234::, ra-names
# Do Router Advertisements, BUT NOT DHCP for this subnet.
# Set the lifetime to 46 hours. (Note: minimum lifetime is 2 hours.)
#dhcp-range=1234::, ra-only, 48h
# Do DHCP and Router Advertisements for this subnet. Set the A bit in the RA
# so that clients can use SLAAC addresses as well as DHCP ones.
#dhcp-range=1234::2, 1234::500, slaac
# Do Router Advertisements and stateless DHCP for this subnet. Clients will
# not get addresses from DHCP, but they will get other configuration information.
# They will use SLAAC for addresses.
#dhcp-range=1234::, ra-stateless
# Do stateless DHCP, SLAAC, and generate DNS names for SLAAC addresses
# from DHCPv4 leases.
#dhcp-range=1234::, ra-stateless, ra-names
# Do router advertisements for all subnets where we're doing DHCPv6
# Unless overriden by ra-stateless, ra-names, et al, the router
# advertisements will have the M and O bits set, so that the clients
# get addresses and configuration from DHCPv6, and the A bit reset, so the
# clients don't use SLAAC addresses.
#enable-ra
# Supply parameters for specified hosts using DHCP. There are lots
# of valid alternatives, so we will give examples of each. Note that
# IP addresses DO NOT have to be in the range given above, they just
# need to be on the same network. The order of the parameters in these
# do not matter, it's permissible to give name, address and MAC in any
# order.
# Always allocate the host with Ethernet address 11:22:33:44:55:66
# The IP address 192.168.0.60
#dhcp-host=11:22:33:44:55:66,192.168.0.60
# Always set the name of the host with hardware address
# 11:22:33:44:55:66 to be "fred"
#dhcp-host=11:22:33:44:55:66,fred
# Always give the host with Ethernet address 11:22:33:44:55:66
# the name fred and IP address 192.168.0.60 and lease time 45 minutes
#dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m
# Give a host with Ethernet address 11:22:33:44:55:66 or
# 12:34:56:78:90:12 the IP address 192.168.0.60. Dnsmasq will assume
# that these two Ethernet interfaces will never be in use at the same
# time, and give the IP address to the second, even if it is already
# in use by the first. Useful for laptops with wired and wireless
# addresses.
#dhcp-host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.60
# Give the machine which says its name is "bert" IP address
# 192.168.0.70 and an infinite lease
#dhcp-host=bert,192.168.0.70,infinite
# Always give the host with client identifier 01:02:02:04
# the IP address 192.168.0.60
#dhcp-host=id:01:02:02:04,192.168.0.60
# Always give the host with client identifier "marjorie"
# the IP address 192.168.0.60
#dhcp-host=id:marjorie,192.168.0.60
# Enable the address given for "judge" in /etc/hosts
# to be given to a machine presenting the name "judge" when
# it asks for a DHCP lease.
#dhcp-host=judge
# Never offer DHCP service to a machine whose Ethernet
# address is 11:22:33:44:55:66
#dhcp-host=11:22:33:44:55:66,ignore
# Ignore any client-id presented by the machine with Ethernet
# address 11:22:33:44:55:66. This is useful to prevent a machine
# being treated differently when running under different OS's or
# between PXE boot and OS boot.
#dhcp-host=11:22:33:44:55:66,id:*
# Send extra options which are tagged as "red" to
# the machine with Ethernet address 11:22:33:44:55:66
#dhcp-host=11:22:33:44:55:66,set:red
# Send extra options which are tagged as "red" to
# any machine with Ethernet address starting 11:22:33:
#dhcp-host=11:22:33:*:*:*,set:red
# Give a fixed IPv6 address and name to client with
# DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2
# Note the MAC addresses CANNOT be used to identify DHCPv6 clients.
# Note also the they [] around the IPv6 address are obilgatory.
#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5]
# Ignore any clients which are not specified in dhcp-host lines
# or /etc/ethers. Equivalent to ISC "deny unknown-clients".
# This relies on the special "known" tag which is set when
# a host is matched.
#dhcp-ignore=tag:!known
# Send extra options which are tagged as "red" to any machine whose
# DHCP vendorclass string includes the substring "Linux"
#dhcp-vendorclass=set:red,Linux
# Send extra options which are tagged as "red" to any machine one
# of whose DHCP userclass strings includes the substring "accounts"
#dhcp-userclass=set:red,accounts
# Send extra options which are tagged as "red" to any machine whose
# MAC address matches the pattern.
#dhcp-mac=set:red,00:60:8C:*:*:*
# If this line is uncommented, dnsmasq will read /etc/ethers and act
# on the ethernet-address/IP pairs found there just as if they had
# been given as --dhcp-host options. Useful if you keep
# MAC-address/host mappings there for other purposes.
#read-ethers
# Send options to hosts which ask for a DHCP lease.
# See RFC 2132 for details of available options.
# Common options can be given to dnsmasq by name:
# run "dnsmasq --help dhcp" to get a list.
# Note that all the common settings, such as netmask and
# broadcast address, DNS server and default route, are given
# sane defaults by dnsmasq. You very likely will not need
# any dhcp-options. If you use Windows clients and Samba, there
# are some options which are recommended, they are detailed at the
# end of this section.
# Override the default route supplied by dnsmasq, which assumes the
# router is the same machine as the one running dnsmasq.
#dhcp-option=3,1.2.3.4
# Do the same thing, but using the option name
#dhcp-option=option:router,1.2.3.4
# Override the default route supplied by dnsmasq and send no default
# route at all. Note that this only works for the options sent by
# default (1, 3, 6, 12, 28) the same line will send a zero-length option
# for all other option numbers.
#dhcp-option=3
# Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5
#dhcp-option=option:ntp-server,192.168.0.4,10.10.0.5
# Send DHCPv6 option. Note [] around IPv6 addresses.
#dhcp-option=option6:dns-server,[1234::77],[1234::88]
# Send DHCPv6 option for namservers as the machine running
# dnsmasq and another.
#dhcp-option=option6:dns-server,[::],[1234::88]
# Ask client to poll for option changes every six hours. (RFC4242)
#dhcp-option=option6:information-refresh-time,6h
# Set the NTP time server address to be the same machine as
# is running dnsmasq
#dhcp-option=42,0.0.0.0
# Set the NIS domain name to "welly"
#dhcp-option=40,welly
# Set the default time-to-live to 50
#dhcp-option=23,50
# Set the "all subnets are local" flag
#dhcp-option=27,1
# Send the etherboot magic flag and then etherboot options (a string).
#dhcp-option=128,e4:45:74:68:00:00
#dhcp-option=129,NIC=eepro100
# Specify an option which will only be sent to the "red" network
# (see dhcp-range for the declaration of the "red" network)
# Note that the tag: part must precede the option: part.
#dhcp-option = tag:red, option:ntp-server, 192.168.1.1
# The following DHCP options set up dnsmasq in the same way as is specified
# for the ISC dhcpcd in
# http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.txt
# adapted for a typical dnsmasq installation where the host running
# dnsmasq is also the host running samba.
# you may want to uncomment some or all of them if you use
# Windows clients and Samba.
#dhcp-option=19,0 # option ip-forwarding off
#dhcp-option=44,0.0.0.0 # set netbios-over-TCP/IP nameserver(s) aka WINS server(s)
#dhcp-option=45,0.0.0.0 # netbios datagram distribution server
#dhcp-option=46,8 # netbios node type
# Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave.
#dhcp-option=252,"\n"
# Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP client
# probably doesn't support this......
#dhcp-option=option:domain-search,eng.apple.com,marketing.apple.com
# Send RFC-3442 classless static routes (note the netmask encoding)
#dhcp-option=121,192.168.1.0/24,1.2.3.4,10.0.0.0/8,5.6.7.8
# Send vendor-class specific options encapsulated in DHCP option 43.
# The meaning of the options is defined by the vendor-class so
# options are sent only when the client supplied vendor class
# matches the class given here. (A substring match is OK, so "MSFT"
# matches "MSFT" and "MSFT 5.0"). This example sets the
# mtftp address to 0.0.0.0 for PXEClients.
#dhcp-option=vendor:PXEClient,1,0.0.0.0
# Send microsoft-specific option to tell windows to release the DHCP lease
# when it shuts down. Note the "i" flag, to tell dnsmasq to send the
# value as a four-byte integer - that's what microsoft wants. See
# http://technet2.microsoft.com/WindowsServer/en/library/a70f1bb7-d2d4-49f0-96d6-4b7414ecfaae1033.mspx?mfr=true
#dhcp-option=vendor:MSFT,2,1i
# Send the Encapsulated-vendor-class ID needed by some configurations of
# Etherboot to allow is to recognise the DHCP server.
#dhcp-option=vendor:Etherboot,60,"Etherboot"
# Send options to PXELinux. Note that we need to send the options even
# though they don't appear in the parameter request list, so we need
# to use dhcp-option-force here.
# See http://syslinux.zytor.com/pxe.php#special for details.
# Magic number - needed before anything else is recognised
#dhcp-option-force=208,f1:00:74:7e
# Configuration file name
#dhcp-option-force=209,configs/common
# Path prefix
#dhcp-option-force=210,/tftpboot/pxelinux/files/
# Reboot time. (Note 'i' to send 32-bit value)
#dhcp-option-force=211,30i
# Set the boot filename for netboot/PXE. You will only need
# this is you want to boot machines over the network and you will need
# a TFTP server; either dnsmasq's built in TFTP server or an
# external one. (See below for how to enable the TFTP server.)
#dhcp-boot=pxelinux.0
# The same as above, but use custom tftp-server instead machine running dnsmasq
#dhcp-boot=pxelinux,server.name,192.168.1.100
# Boot for Etherboot gPXE. The idea is to send two different
# filenames, the first loads gPXE, and the second tells gPXE what to
# load. The dhcp-match sets the gpxe tag for requests from gPXE.
#dhcp-match=set:gpxe,175 # gPXE sends a 175 option.
#dhcp-boot=tag:!gpxe,undionly.kpxe
#dhcp-boot=mybootimage
# Encapsulated options for Etherboot gPXE. All the options are
# encapsulated within option 175
#dhcp-option=encap:175, 1, 5b # priority code
#dhcp-option=encap:175, 176, 1b # no-proxydhcp
#dhcp-option=encap:175, 177, string # bus-id
#dhcp-option=encap:175, 189, 1b # BIOS drive code
#dhcp-option=encap:175, 190, user # iSCSI username
#dhcp-option=encap:175, 191, pass # iSCSI password
# Test for the architecture of a netboot client. PXE clients are
# supposed to send their architecture as option 93. (See RFC 4578)
#dhcp-match=peecees, option:client-arch, 0 #x86-32
#dhcp-match=itanics, option:client-arch, 2 #IA64
#dhcp-match=hammers, option:client-arch, 6 #x86-64
#dhcp-match=mactels, option:client-arch, 7 #EFI x86-64
# Do real PXE, rather than just booting a single file, this is an
# alternative to dhcp-boot.
#pxe-prompt="What system shall I netboot?"
# or with timeout before first available action is taken:
#pxe-prompt="Press F8 for menu.", 60
# Available boot services. for PXE.
#pxe-service=x86PC, "Boot from local disk"
# Loads <tftp-root>/pxelinux.0 from dnsmasq TFTP server.
#pxe-service=x86PC, "Install Linux", pxelinux
# Loads <tftp-root>/pxelinux.0 from TFTP server at 1.2.3.4.
# Beware this fails on old PXE ROMS.
#pxe-service=x86PC, "Install Linux", pxelinux, 1.2.3.4
# Use bootserver on network, found my multicast or broadcast.
#pxe-service=x86PC, "Install windows from RIS server", 1
# Use bootserver at a known IP address.
#pxe-service=x86PC, "Install windows from RIS server", 1, 1.2.3.4
# If you have multicast-FTP available,
# information for that can be passed in a similar way using options 1
# to 5. See page 19 of
# http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf
# Enable dnsmasq's built-in TFTP server
#enable-tftp
# Set the root directory for files available via FTP.
#tftp-root=/var/ftpd
# Make the TFTP server more secure: with this set, only files owned by
# the user dnsmasq is running as will be send over the net.
#tftp-secure
# This option stops dnsmasq from negotiating a larger blocksize for TFTP
# transfers. It will slow things down, but may rescue some broken TFTP
# clients.
#tftp-no-blocksize
# Set the boot file name only when the "red" tag is set.
#dhcp-boot=net:red,pxelinux.red-net
# An example of dhcp-boot with an external TFTP server: the name and IP
# address of the server are given after the filename.
# Can fail with old PXE ROMS. Overridden by --pxe-service.
#dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3
# If there are multiple external tftp servers having a same name
# (using /etc/hosts) then that name can be specified as the
# tftp_servername (the third option to dhcp-boot) and in that
# case dnsmasq resolves this name and returns the resultant IP
# addresses in round robin fasion. This facility can be used to
# load balance the tftp load among a set of servers.
#dhcp-boot=/var/ftpd/pxelinux.0,boothost,tftp_server_name
# Set the limit on DHCP leases, the default is 150
#dhcp-lease-max=150
# The DHCP server needs somewhere on disk to keep its lease database.
# This defaults to a sane location, but if you want to change it, use
# the line below.
#dhcp-leasefile=/var/lib/misc/dnsmasq.leases
# Set the DHCP server to authoritative mode. In this mode it will barge in
# and take over the lease for any client which broadcasts on the network,
# whether it has a record of the lease or not. This avoids long timeouts
# when a machine wakes up on a new network. DO NOT enable this if there's
# the slightest chance that you might end up accidentally configuring a DHCP
# server for your campus/company accidentally. The ISC server uses
# the same option, and this URL provides more information:
# http://www.isc.org/files/auth.html
#dhcp-authoritative
# Run an executable when a DHCP lease is created or destroyed.
# The arguments sent to the script are "add" or "del",
# then the MAC address, the IP address and finally the hostname
# if there is one.
#dhcp-script=/bin/echo
# Set the cachesize here.
#cache-size=150
# If you want to disable negative caching, uncomment this.
#no-negcache
# Normally responses which come from /etc/hosts and the DHCP lease
# file have Time-To-Live set as zero, which conventionally means
# do not cache further. If you are happy to trade lower load on the
# server for potentially stale date, you can set a time-to-live (in
# seconds) here.
#local-ttl=
# If you want dnsmasq to detect attempts by Verisign to send queries
# to unregistered .com and .net hosts to its sitefinder service and
# have dnsmasq instead return the correct NXDOMAIN response, uncomment
# this line. You can add similar lines to do the same for other
# registries which have implemented wildcard A records.
#bogus-nxdomain=64.94.110.11
# If you want to fix up DNS results from upstream servers, use the
# alias option. This only works for IPv4.
# This alias makes a result of 1.2.3.4 appear as 5.6.7.8
#alias=1.2.3.4,5.6.7.8
# and this maps 1.2.3.x to 5.6.7.x
#alias=1.2.3.0,5.6.7.0,255.255.255.0
# and this maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40
#alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0
# Change these lines if you want dnsmasq to serve MX records.
# Return an MX record named "maildomain.com" with target
# servermachine.com and preference 50
#mx-host=maildomain.com,servermachine.com,50
# Set the default target for MX records created using the localmx option.
#mx-target=servermachine.com
# Return an MX record pointing to the mx-target for all local
# machines.
#localmx
# Return an MX record pointing to itself for all local machines.
#selfmx
# Change the following lines if you want dnsmasq to serve SRV
# records. These are useful if you want to serve ldap requests for
# Active Directory and other windows-originated DNS requests.
# See RFC 2782.
# You may add multiple srv-host lines.
# The fields are <name>,<target>,<port>,<priority>,<weight>
# If the domain part if missing from the name (so that is just has the
# service and protocol sections) then the domain given by the domain=
# config option is used. (Note that expand-hosts does not need to be
# set for this to work.)
# A SRV record sending LDAP for the example.com domain to
# ldapserver.example.com port 389
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389
# A SRV record sending LDAP for the example.com domain to
# ldapserver.example.com port 389 (using domain=)
#domain=example.com
#srv-host=_ldap._tcp,ldapserver.example.com,389
# Two SRV records for LDAP, each with different priorities
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2
# A SRV record indicating that there is no LDAP server for the domain
# example.com
#srv-host=_ldap._tcp.example.com
# The following line shows how to make dnsmasq serve an arbitrary PTR
# record. This is useful for DNS-SD. (Note that the
# domain-name expansion done for SRV records _does_not
# occur for PTR records.)
#ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services"
# Change the following lines to enable dnsmasq to serve TXT records.
# These are used for things like SPF and zeroconf. (Note that the
# domain-name expansion done for SRV records _does_not
# occur for TXT records.)
#Example SPF.
#txt-record=example.com,"v=spf1 a -all"
#Example zeroconf
#txt-record=_http._tcp.example.com,name=value,paper=A4
# Provide an alias for a "local" DNS name. Note that this _only_ works
# for targets which are names from DHCP or /etc/hosts. Give host
# "bert" another name, bertrand
#cname=bertand,bert
# For debugging purposes, log each DNS query as it passes through
# dnsmasq.
#log-queries
# Log lots of extra information about DHCP transactions.
#log-dhcp
# Include a another lot of configuration options.
#conf-file=/etc/dnsmasq-resolvconf.conf
#conf-dir=/etc/dnsmasq.d
domain-needed
interface=lo
# If dnsmasq is compiled for DBus then we can take
# advantage of not having to restart dnsmasq.
enable-dbus
conf-file=/etc/dnsmasq-conf.conf
resolv-file=/etc/dnsmasq-resolv.conf
Logs:
May 23 00:01:06 panzor systemd[1]: Failed to start A lightweight DHCP and caching DNS server.
May 23 00:01:10 panzor dhcpcd[27267]: dhcpcd not running
May 23 00:01:10 panzor kernel: [ 7771.282756] iwl4965 0000:03:00.0: Can't stop Rx DMA.
May 23 00:01:10 panzor dhcpcd[27294]: dhcpcd not running
May 23 00:01:11 panzor dhcpcd[27330]: dhcpcd not running
May 23 00:01:14 panzor dhcpcd[27373]: wlan0: sendmsg: Cannot assign requested address
May 23 00:01:18 panzor dhcpcd[27373]: wlan0: sendmsg: Operation not permitted
May 23 00:01:22 panzor dhcpcd[27395]: wlan0: sendmsg: Operation not permitted
May 23 00:01:26 panzor dhcpcd[27395]: wlan0: sendmsg: Operation not permitted
For domain filtration, if I remember correctly, I am using this
https://bbs.archlinux.org/viewtopic.php?id=139784

Where do deleted Static DNS records go?

Since we enabled the Active Directory recycle bin some time ago, we noticed that there is also a recycle bin for the ForestDNSRecords and DomainDNSRecords container. It appears that dynamic DNS entries are being treated like any other object and getting
moved to CN=Deleted Objects,DC=<Domain|Forest>DNSZones,DC=<YourDomain>,DC=<Suffix>. When Static entries are deleted we do not see them in the Deleted Objects container. Is that a bug, by design, or are we missing something?

Static records should show up along with dynamically created records. I don't believe they would go anywhere else, since they are just DNS nodes in the same context. Maybe there's some other mitigating issue that may be causing it?
Have you seen the following links? If not, let us know what links you were reading, please.
What to do when DNS records disappear
http://searchwindowsserver.techtarget.com/tip/What-to-do-when-DNS-records-disappear
Using AD Recycle Bin to restore deleted DNS zones and their contents in Windows Server 2008 R2
http://blogs.technet.com/b/askds/archive/2010/08/12/using-ad-recycle-bin-to-restore-deleted-dns-zones-and-their-contents-in-windows-server-2008-r2.aspx
Curious, when you deleted the dynamic and static records, did you do that on the same DC in the same AD Site?
Are there any replication errors or issues?
Let's also eliminate any possibilities of the existence of duplicate AD integrated zones. If there are, one DC's *view* or what it *sees* in a partition will be different than another DC's view.
Using ADSI Edit to Resolve Conflicting or Duplicate AD Integrated DNS zones
http://blogs.msmvps.com/acefekay/2009/09/02/using-adsi-edit-to-resolve-conflicting-or-duplicate-ad-integrated-dns-zones
Ace Fekay
MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights.

Doubt with Dynamic Interfaces and VLANs

Hello.
I am trying to get wirelles clientes and APs to be on the same VLAN/subnet, now is working with management interface on my WLC 5508. My problem comes up when I change them to a new dynamic interface.
Before any change:
VLAN: 8
Management Interface IP: 192.168.9.2/23
Gateway: 192.168.8.1
DHCP Server: 192.168.8.2
WLAN SSID linked to Managment interface: Ray123
APs on VLAN 8 and subnet static IP range192.168.9.0/23
There is no dynamic interface.
After changes.
VLAN: 0
Management Interface: 192.168.6.2/23
Gateway: 192.168.6.1
DHCP Server: 192.168.6.2
Dynamic interface name: Wireless-1
VLAN: 8
Management Interface IP: 192.168.9.2/23
Gateway: 192.168.8.1
DHCP Server: 192.168.8.2
WLAN SSID linked to Dynamic interface: Ray123
APs still on VLAN 8 and subnet static IP range192.168.9.0/23
After all this done i can see by cdp neighbors all my APs i can ping them and management interface too, but APs are not registered, no clients too.
According to this guide:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00805e7a24.shtml
Dynamic interfaces and APs should be on the same VLAN.
But this another guide states the opposite:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html
"Set the APs in a VLAN that is different from the dynamic interface configured on the Controller. If the APs are in the same VLAN as the dynamic interface, the APs are not registered on the Controller and the 'LWAPP discovery rejected' and 'Layer 3 discovery request not received on management VLAN' errors are logged on the Controller"
I cant understand why VLANs for APs and dynamic interfaces should be on different, it has no sense to configure a vlan intended for APs which shouldnt be on the same vlan.
Please tell me what is wrong.
Thanks in advance.

You have to tell the APs where the WLC lives now, 192.168.6.2.
You can do this in the following ways:
Manual Prime the APs
option 43
dns
ip forward udp 5246
move the aps to the same vlan as the management interface let them join and then chnage the vlan
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

How can we get Dynamic columns and data with RTF Templates in BI Publisher

How can we get Dynamic columns and data with RTf Templates.
My requirement is :
create table xxinv_item_pei_taginfo(item_id number,
Organization_id number,
item varchar2(4000),
record_type varchar2(4000),
record_value CLOB,
State varchar2(4000));
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'USES','fever','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'HOW TO USE','one tablet daily','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'SIDE EFFECTS','XYZ','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'DRUG INTERACTION','ABC','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'OVERDOSE','Go and see doctor','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'NOTES','Take after meal','TX');
select * from xxinv_item_pei_taginfo;
Item id Org Id Item Record_type Record_value State
493991     224     1265-D30     USES     fever     TX
493991     224     1265-D30     HOW TO USE     one tablet daily     TX
493991     224     1265-D30     SIDE EFFECTS     XYZ     TX
493991     224     1265-D30     DRUG INTERACTION     ABC     TX
493991     224     1265-D30     OVERDOSE      Go and see doctor     TX
493991     224     1265-D30     NOTES     Take after meal     TX
Above is my data
I have to fetch the record_type from a lookup where I can have any of the record type, sometime USES, HOW TO USE, SIDE EFFECTS and sometimes some other set of record types
In my report I have to get these record typpes as field name dynamically whichever is available in that lookup and record values against them.
its a BI Publisher report.
please suggest

if you have data in db then you can create xml with needed structure
and so you can create bip report
do you have errors or .... ?

Rvs 4000 dynamic ip and static dns

Similar Messages

Maybe you are looking for