RVS 4000 HTTP mgmt interface hangs @ Port 80 & DHCP stops working

This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
Internet connection is DHCP
LAN is set to DHCP with several Static devices defined
DMZ is dsabled
Functionining as a gateway
Time is set via NTP & the NRC
IPV4 Only
Everything is pretty much dedault except for QoS
Trust mode is Port, set to 4, 4, 4, 1
( Port 4 has a Linksys ATA plugged into it for VOIP services )
SIP Port Forwarding is enabled for 5060
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.
When this happens the only remedy is to power reboot.
Everthing comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.
My next step is to setuo a syslog server and have the logs copied out.
Anyone see this kind of behavior before ?
Any ideas ??
(  No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102  )
Thanks Derek

Hi there Vijay !
I cannot upgrade to that version of Firmware as my RVS4000 is a V1, not a V2.
Is there some way I can change it such that it will load the newer Firmware ?
This is the error I receive when trying to upgrade anyway :
"Upgrade file is not the correct type or version for this device.
Upgrade failed.
Please obtain the correct file and try again."
Otherwise the newest firmware I can load is 1.3.3.5
( which seems to have this problem )

Similar Messages

  • Port forwarding stops working several hours after reset

    I have a WRT350N (fw v. 1.03.2).  It's connected to an Alcatel ADSL modem (PPPoE configuration).  I've configured port forwarding to allow HTTP and SSH into a linux box on my home network (static IP).  I am able to get to the linux box from outside for the first few hours after I set up the configuration, but a few hours later I am no longer able to get to it from outside - port forwarding stops working though the settings remain as I'd left them.  Over the course of various attempts I've had the external connections just die (404 errors, host not found, etc) and sometimes the connection went to the router - getting the WRT350N login prompt (remote management is turned on, but on port 8080, not 80, so this was unexpected).
    The only way I've found to resolve this is to reset to factory defaults and reconfigure.  Then it works again for a few hours and shortly is again not forwarding.  I've tried other ports (VNC, RDC, telnet, SMTP) and the forwarding stops working on all ports at the same time.  My home machines are able to get out to the internet with no problems.
    I thought the router had a hardware flaw so i replaced it with an identical model yesterday, and sure enough, today I'm again stuck without external access to my home website.
    Any thoughts or suggestions would be welcome.
    Thanks,
    Nick

    I was able to trace the problem to torrent downloads.  It seems the router wasn't handling all the concurrent connections when handling torrents.  I haven't had problems since i stopped downloading torrent files.  I did add a static port mapping and configured utorrent to run on a single port on a machine with a static address but haven't had cause to download any torrent files since then, so i don't know if that will fix the problem.
    That being said, i've had no issues since i stopped the torrents.
    HTH
    Nick

  • USB Ports Randomly Stop Working

    I have an HP Pavilion dv6 Notebook with Windows 7. All of the ports, 2 2.0 and 2 3.0 ports, began to randomly stop working. My mouse light would still light up, but the mouse wouldn't work. If I rebooted the entire laptop, all of the ports would come back on for a short period of time before they randomly shut off again. They will also come back on for a short period of time if I close the lid for a few seconds and reopen it. However, lately, the 3.0 ports have stopped working entirely and the 2.0 ports stopping is becoming more frequent.
    The first time I noticed this was when I was testing a micro usb cable (it has stopped charging and I was testing whether it was the cable or the wall adapter). I plugged the cable into one of the 2.0 ports and it gave me a USB surge warning. Other than that, I haven't received any notices. The drivers are up to date. I have uninstalld the root hubs multiple times. I have tried all kinds of Power plans for the laptop. Nothing works. The USB ports still stop working, and it's becoming increasingly more frustrating.

    Hello Abby_Renee,
    With the USB 3.0 port not working, and your 2.0 port working intermittently, I would suggest the following document Troubleshooting USB Connections (Windows 7) for troubleshooting.
    In this document there is a specific option for USB 3.0 ports stop working, which would be the best steps to follow for your 3.0 ports. Now for the 2.0 ports, I would suggest USB device not detected by Windows (no device name in device manager), or the other option is USB devices are detected by Windows but are not working properly. The last two options are dependant on the specific errors you are experiencing.
    Please let me know the outcome of the troubleshooting steps.
    Good Luck!
    I worked on behalf of HP

  • I was using my HDMI port to connect to my TV .port just stopped working

    I was using my HDMI port to connect to my TV .port just stopped working
    HP Pavilion g6 Notebook PC
    Version 6.3.9600 Build 9600

    Hey @kirilsubacs ,
    Welcome to the HP Forum!
    I understand the HDMI port has stopped working on your Pavilion G6 notebook.
    It would help to know exactly which notebook you are using and the installed operating system. For information on finding your product and model numbers click here: How Do I Find My Model Number or Product Number? To see which version of Windows you are using click here: Which Windows operating system am I running?
    If this is a new issue I would start by doing a system restore. This will undo any changes to the operating system and uninstall any Windows updates, programs, or program updates installed after the restore date. This will not delete your personal files.
    If that doesn't work try updating the drivers for your graphics card (GPU). You can find the drivers for your notebook here: HP - Drivers & Downloads.
    Let me know if that helps or please provide the model and operating system of the notebook.
    Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    The Great Deku Tree
    I work on behalf of HP.

  • Port forward stopped working after update

    i updated my software and the port forward stopped working and it will no longer allow access to my ip camera.

    Hey Cab,
    Yea, mine stopped working since the update to 10.8.2. It was working fine prior to the update cause I used it at work on a 50 inch Samsung. I undrstand that there was a driver update but I'm not sure why.

  • Why does my line-in audio port quit stop working while recording?

    My set-up is a bit confusing, so I'll try and be very specific.
    I record into Garageband via the following set-up:
    Microphone(s) run into TASCAM 4-track -> RCA-to-Stereo Cable runs out of TASCAM into MacBook Pro via the single audio port.
    This generally works fine for several hours, but the last 3 times I've had a recording session, the audio signal has dropped to virtually nil without any warning. At this point, even yelling into the microphone (with the TASCAM max-ing out) will only produce 1 volume bar in the "Line-In" system preference screen. At best, it sounds like a very quiet whisper.
    My microphone is working (works while recording to tape) as does my cable (RCA - to - Stereo) when used in other situations. Any ideas as to why this is happening? Am I tripping some sort of internal line-in volume...protector? (Is that even a thing?) Or do I need a new audio port?

    funny how to one seems to have an answer for this, I just posted my own issue, audio in line port just stopped working after update.

  • E2000 Port Forwarding Stops Working

    I am using port forwarding for running a webserver. All is working fine. After a random number of hours or days, the port forwarding stops working. I can get in and look at the settings and they are correct. I can then change something on the port forwarding screen and resave it and it starts working again.  Do I have a bad unit ?

    Webserver might not be set to static IP. Try setting the webserver to static IP first, then make sure that static IP is enabled in the Port Forwarding screen of the router's web-based setup page. Also, protocol should be set to BOTH (TCP-UDP). You can also try having less firewall/AV restrictions on the web server (or none at all) and set MTU to 1400.

  • I have a mac book pro that both USB ports have stopped working one about a year ago and one recently. Is it possible to connect to another one of the other MBP's  ports with a cord that ends with a USB port?

    I have a mac book pro that both USB ports have stopped working one about a year ago and one recently. Is it possible to connect to another one of the other MBP's  ports with a cord that ends with a USB port?

    Thank you For your time and thoughts!
    I went by the Apple Store and they told me that there was a "Flat Rate" repair service for this particular part where they would replace the logic board along with the USB ports for $350. Seems like best avenue. All of this would have been moot but my wifi in the computer also doesn't work so I was using my phone as a hot spot and tethering it to the computer for Internet access when the last port quit. This left me with no internet and no printing capabilities on the computer I use for my business. Basically became a nice paperweight. lol
    They will ship it off Monday and I should have it back Thursday!
    Again, thank you!

  • Ethernet Port randomly stopped working - u310 ultrabook

    Hi,
    So my Ethernet Port on the u310 Ideapad has randomly stopped working - by that I mean that when I plug in my LAN wire, the lights will show only when I switch on my laptop, till the Windows logo comes on, which is when the lights of the port go off and the port refuses to work.
    I need LAN pretty urgently, so I was wondering if someone could please help me out! Thanks!

    Hi Ipsh,
    thanks for posting and welcome to the community. Based from your post there is apossibility that it it could be hardware. But however before we confirm let just trya few setting and software adjustment first. At this point I was just wondering if you have tried doing a software update, I would suggest you to uninstall the current drivers you have now and reinstall the drivers below.
    http://download.lenovo.com/consumer/mobiles/0wla01ww.exe
    Please be informed that the driver above is meant for windows 7, if you have another operating system installed do let me know.
    Regards

  • Port mapping stopped working using Mavericks

    Hi,
    on Snow Leopard, I had iVPN using port mapping up-and-running.
    Basically using this explanation (https://discussions.apple.com/docs/DOC-3415).
    On Mavericks it stopped working.
    I'm running AE 7.7.2, and Mavericks 10.9.1.
    Tools I tried are iVPN together with a DynDNS setup (also the Personal Website).
    I don't get non of these working anymore...
    Any ideas?
    Regards.

    OK solved, or at least the problem was not with the modem or router.
    Oddly, enough the app I was using to test the port forwarding did not recognize that the ports were open. Nor did the internet via canyouseeme.org. However, when I tried a previous version of the same app, it worked fine.
    I am still using 7.6.1, but I will upgrade the firmware and see if things are still ok.
    Sorry to clog up the boards with what turned out to be a non-issue. I'd erase this post if I knew how.

  • My usb ports have stopped working on my iMac

    2 of the 4 USB ports on my imac have stopped working. Has anyone else had the same problem? Anyone know how to get them working again?
    Thanks
    Pammac1

    Hopefully the SMC reset works otherwise it may be a Logic Board issue.
    SMC RESET
    http://support.apple.com/kb/HT3964
    Shut down the computer.
    Unplug the computer's power cord and ALL peripherals.
    Wait 15 seconds.
    Attach the computers power cable.
    Wait another 5 seconds and press the power button to turn on the computer.
    The 5 second timing is important to a successful reset.
    PRAM RESET
    Zap the PRAM
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • Port Forwarding Stops Working WRT400N

    Is anyone else having a problem with port forwarding on their WRT400N? I'm forwarding one service (https) and this stops working if it's not accessed after a 10 days or so. The only way to get it to work again is to reboot the router. I’m running the “latest" firmware, which is an oxymoron considering it's been over 12 MONTHS since Linksys updated the code... Which is appalling considering this appears to be their flagship wireless N router.

    I tried the hard reset and still the same problem, port forwarding stops after a period of time.   Sometimes 1 day, other times 10 days.  I have 2 servers on the local network, each running Remote Desktop on port 3389.  I have 2 ports forwarded to get to either server depending on the external port number.   E.g.:  The external port forward is {wan_ip_addr}:33389->{server 1}:3389 to get to server 1 and, {wan_ip_addr}:23389->{server 2}:3389 to get to server 2.  Works great when it works, but then, without error, just the port forwarding stops, and all other router functions seem to continue working.  Has anyone else come across this?  Any fixes?  Help!!!!
    Thanks in advance to any help!!

  • USB ports suddenly stop working: xhci_hcd and ehci_hcdwontload[SOLVED]

    Hello everyone.  I am having USB issues on my HP dv6t-7000. I was using my USB keyboard/mouse and the USB was working fine.  I then plug in a flash drive and ALL USB PORTS STOP WORKING.  So I tried the usual fix of reloading xhci_hcd. 
    rmmod xhci_hcd
    modprobe xhci_hcd
    but nothing happens.  I check lsmod and the module is not loaded. Neither is ehci_hcd:
    Module Size Used by
    nls_utf8 1353 1
    udf 80114 1
    crc_itu_t 1364 1 udf
    fuse 69245 3
    bbswitch 5731 0
    coretemp 6231 0
    kvm_intel 124064 0
    kvm 384721 1 kvm_intel
    arc4 2008 2
    crc32c_intel 1988 0
    ghash_clmulni_intel 4598 0
    aesni_intel 46104 0
    uvcvideo 73462 0
    videobuf2_vmalloc 2789 1 uvcvideo
    videobuf2_memops 2827 1 videobuf2_vmalloc
    videobuf2_core 24073 1 uvcvideo
    aes_x86_64 7556 1 aesni_intel
    videodev 104777 2 uvcvideo,videobuf2_core
    rt2800pci 9864 0
    rt2800lib 49648 1 rt2800pci
    rt2x00pci 5052 1 rt2800pci
    rt2x00lib 36341 3 rt2x00pci,rt2800lib,rt2800pci
    snd_hda_codec_hdmi 27561 1
    snd_hda_codec_idt 55976 1
    hp_wmi 7899 0
    snd_hda_intel 27700 2
    snd_hda_codec 100743 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel
    snd_hwdep 6429 1 snd_hda_codec
    snd_pcm 77827 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
    acpi_cpufreq 10631 1
    eeprom_93cx6 2218 1 rt2800pci
    mperf 1268 1 acpi_cpufreq
    mac80211 432402 3 rt2x00lib,rt2x00pci,rt2800lib
    cfg80211 179435 2 mac80211,rt2x00lib
    ablk_helper 1973 1 aesni_intel
    snd_page_alloc 7427 2 snd_pcm,snd_hda_intel
    hp_accel 16521 0
    psmouse 76176 0
    media 10438 2 uvcvideo,videodev
    sparse_keymap 3089 1 hp_wmi
    lis3lv02d 11636 1 hp_accel
    iTCO_wdt 5288 0
    serio_raw 5074 0
    input_polldev 2915 1 lis3lv02d
    joydev 9728 0
    processor 27496 1 acpi_cpufreq
    pcspkr 1900 0
    rfkill 15997 3 cfg80211,hp_wmi
    snd_timer 18935 1 snd_pcm
    mei 61037 0
    cryptd 8742 3 ghash_clmulni_intel,aesni_intel,ablk_helper
    evdev 10137 11
    iTCO_vendor_support 1930 1 iTCO_wdt
    ac 2569 0
    thermal 8418 0
    battery 7099 0
    lpc_ich 11346 0
    xts 3136 1 aesni_intel
    r8169 56712 0
    lrw 3662 1 aesni_intel
    mii 4092 1 r8169
    gf128mul 6051 2 lrw,xts
    crc_ccitt 1364 1 rt2800lib
    i2c_i801 10917 0
    snd 60157 11 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_idt,snd_pcm,snd_hda_codec,snd_hda_intel
    hid_generic 1146 0
    mxm_wmi 1468 0
    wmi 8380 2 hp_wmi,mxm_wmi
    microcode 14434 0
    soundcore 5443 1 snd
    ext4 447457 2
    crc16 1360 1 ext4
    jbd2 78834 1 ext4
    mbcache 6027 1 ext4
    usbhid 41358 0
    hid 86421 2 hid_generic,usbhid
    sr_mod 14824 1
    cdrom 35521 1 sr_mod
    sd_mod 31067 3
    ahci 21393 5
    libahci 20907 1 ahci
    libata 168540 2 ahci,libahci
    scsi_mod 130423 3 libata,sd_mod,sr_mod
    usbcore 173914 2 uvcvideo,usbhid
    usb_common 955 1 usbcore
    i915 526734 3
    video 11332 1 i915
    button 4670 1 i915
    i2c_algo_bit 5392 1 i915
    intel_agp 10745 1 i915
    intel_gtt 15361 2 i915,intel_agp
    drm_kms_helper 33007 1 i915
    drm 225482 4 i915,drm_kms_helper
    i2c_core 23076 6 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,videodev
    Then I look at dmesg:
    [ 2179.728545] usb 3-1: new high-speed USB device number 3 using xhci_hcd
    [ 2181.739284] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 2 with no TDs queued?
    [ 2181.739289] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 1 with no TDs queued?
    [ 2181.739292] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 0 with no TDs queued?
    [ 2198.969052] xhci_hcd 0000:00:14.0: remove, state 4
    [ 2198.969064] usb usb4: USB disconnect, device number 1
    [ 2198.969194] xHCI xhci_drop_endpoint called for root hub
    [ 2198.969197] xHCI xhci_check_bandwidth called for root hub
    [ 2198.973684] xhci_hcd 0000:00:14.0: USB bus 4 deregistered
    [ 2198.973694] xhci_hcd 0000:00:14.0: remove, state 1
    [ 2198.973701] usb usb3: USB disconnect, device number 1
    [ 2198.973704] usb 3-1: USB disconnect, device number 3
    [ 2198.974681] usb 3-4: USB disconnect, device number 2
    [ 2199.140187] xhci_hcd 0000:00:14.0: Slot 1 endpoint 2 not removed from BW list!
    [ 2199.140192] xhci_hcd 0000:00:14.0: Slot 1 endpoint 4 not removed from BW list!
    [ 2199.140308] xHCI xhci_drop_endpoint called for root hub
    [ 2199.140311] xHCI xhci_check_bandwidth called for root hub
    [ 2199.140639] xhci_hcd 0000:00:14.0: USB bus 3 deregistered
    [ 2328.659201] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 2328.868886] usb 1-1.2: new high-speed USB device number 5 using ehci_hcd
    [ 2347.145796] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 2347.288443] usb 1-1.2: USB disconnect, device number 5
    [ 2359.582513] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 2359.795564] usb 1-1.2: new high-speed USB device number 6 using ehci_hcd
    [ 2376.424057] ehci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 2376.450686] ehci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 2376.450717] ehci_hcd 0000:00:1d.0: remove, state 4
    [ 2376.450728] usb usb2: USB disconnect, device number 1
    [ 2376.450731] usb 2-1: USB disconnect, device number 2
    [ 2376.456233] ehci_hcd 0000:00:1d.0: USB bus 2 deregistered
    [ 2376.467332] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 2376.493962] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 2376.493982] ehci_hcd 0000:00:1a.0: remove, state 4
    [ 2376.493993] usb usb1: USB disconnect, device number 1
    [ 2376.493997] usb 1-1: USB disconnect, device number 2
    [ 2376.493999] usb 1-1.1: USB disconnect, device number 3
    [ 2376.494208] usb 1-1.2: USB disconnect, device number 6
    [ 2376.494346] usb 1-1.3: USB disconnect, device number 4
    [ 2376.536849] ehci_hcd 0000:00:1a.0: USB bus 1 deregistered
    [ 2517.463171] CPU3: Package power limit notification (total events = 81)
    [ 2517.463174] CPU1: Package power limit notification (total events = 81)
    [ 2517.463175] CPU2: Package power limit notification (total events = 81)
    [ 2517.463177] CPU0: Package power limit notification (total events = 81)
    [ 2517.474151] CPU1: Package power limit normal
    [ 2517.474153] CPU2: Package power limit normal
    [ 2517.474154] CPU3: Package power limit normal
    [ 2517.474163] CPU0: Package power limit normal
    [ 3126.529391] CPU1: Package power limit notification (total events = 125)
    [ 3126.529392] CPU0: Package power limit notification (total events = 125)
    [ 3126.529395] CPU2: Package power limit notification (total events = 125)
    [ 3126.529396] CPU3: Package power limit notification (total events = 125)
    [ 3126.529790] CPU1: Package power limit normal
    [ 3126.529791] CPU3: Package power limit normal
    [ 3126.529792] CPU2: Package power limit normal
    [ 3126.529793] CPU0: Package power limit normal
    The journalctl:
    Feb 05 17:28:26 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 2 with no TDs queued?
    Feb 05 17:28:26 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 1 with no TDs queued?
    Feb 05 17:28:26 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 0 with no TDs queued?
    Feb 05 17:28:44 ryan-linux-desktop sudo[26409]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/usr/bin/rmmod xhci_hcd
    Feb 05 17:28:44 ryan-linux-desktop sudo[26409]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:28:44 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: remove, state 4
    Feb 05 17:28:44 ryan-linux-desktop kernel: usb usb4: USB disconnect, device number 1
    Feb 05 17:28:44 ryan-linux-desktop kernel: xHCI xhci_drop_endpoint called for root hub
    Feb 05 17:28:44 ryan-linux-desktop kernel: xHCI xhci_check_bandwidth called for root hub
    Feb 05 17:28:44 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: USB bus 4 deregistered
    Feb 05 17:28:44 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: remove, state 1
    Feb 05 17:28:44 ryan-linux-desktop kernel: usb usb3: USB disconnect, device number 1
    Feb 05 17:28:44 ryan-linux-desktop kernel: usb 3-1: USB disconnect, device number 3
    Feb 05 17:28:44 ryan-linux-desktop kernel: usb 3-4: USB disconnect, device number 2
    Feb 05 17:28:44 ryan-linux-desktop sudo[26409]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:28:44 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: Slot 1 endpoint 2 not removed from BW list!
    Feb 05 17:28:44 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: Slot 1 endpoint 4 not removed from BW list!
    Feb 05 17:28:44 ryan-linux-desktop kernel: xHCI xhci_drop_endpoint called for root hub
    Feb 05 17:28:44 ryan-linux-desktop kernel: xHCI xhci_check_bandwidth called for root hub
    Feb 05 17:28:44 ryan-linux-desktop kernel: xhci_hcd 0000:00:14.0: USB bus 3 deregistered
    Feb 05 17:28:50 ryan-linux-desktop sudo[26473]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:28:50 ryan-linux-desktop sudo[26473]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:28:50 ryan-linux-desktop sudo[26473]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:28:55 ryan-linux-desktop sudo[26522]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:28:55 ryan-linux-desktop sudo[26522]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:28:55 ryan-linux-desktop sudo[26522]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:00 ryan-linux-desktop sudo[26561]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:29:00 ryan-linux-desktop sudo[26561]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:29:00 ryan-linux-desktop sudo[26561]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:10 ryan-linux-desktop sudo[26652]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/usr/bin/rmmod xhci_hcd
    Feb 05 17:29:10 ryan-linux-desktop sudo[26652]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:29:10 ryan-linux-desktop sudo[26652]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:17 ryan-linux-desktop sudo[26714]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:29:17 ryan-linux-desktop sudo[26714]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:29:17 ryan-linux-desktop sudo[26714]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:25 ryan-linux-desktop sudo[26785]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:29:25 ryan-linux-desktop sudo[26785]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:29:25 ryan-linux-desktop sudo[26785]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:29 ryan-linux-desktop sudo[26826]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:29:29 ryan-linux-desktop sudo[26826]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:29:29 ryan-linux-desktop sudo[26826]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:30 ryan-linux-desktop sudo[26836]: ryanvade : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:29:30 ryan-linux-desktop sudo[26836]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:29:30 ryan-linux-desktop sudo[26836]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:29:34 ryan-linux-desktop su[26853]: (to root) ryanvade on /dev/pts/2
    Feb 05 17:29:34 ryan-linux-desktop su[26853]: pam_unix(su:session): session opened for user root by ryanvade(uid=1000)
    Feb 05 17:30:54 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: setting latency timer to 64
    Feb 05 17:30:54 ryan-linux-desktop kernel: usb 1-1.2: new high-speed USB device number 5 using ehci_hcd
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27597]: Warning: Configuration file /etc/laptop-mode/conf.d/board-specific/* is not readable, skipping.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27603]: Warning: Configuration file /etc/laptop-mode/conf.d/board-specific/* is not readable, skipping.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27605]: Determining power state from /sys/class/power_supply/ADP1/online.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27612]: Not trying other options, already found a power supply.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27618]: Determining power state from /sys/class/power_supply/ADP1/online.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27625]: Not trying other options, already found a power supply.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27631]: Battery level polling is disabled.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27636]: Prelim lock acquisition on descriptor 8 with pid 27589
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27640]: Battery level polling is disabled.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27642]: Prelim lock acquisition on descriptor 9 with pid 27589
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27643]: Now invoking lmt_main_function with arguments -- force
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27645]: Prelim lock acquisition on descriptor 8 with pid 27593
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27648]: Couldn't acquire prelim lock on descriptor 9 with pid 27593
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27649]: On battery power: Activating, because ENABLE_LAPTOP_MODE_ON_BATTERY is set.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27650]: Now invoking lock_retry with arguments -- force
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27652]: Not on AC and we have battery information in /sys/class/power_supply/BAT* -- checking minimum battery charge.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27656]: /sys/class/power_supply/ADP1 is of type Mains.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27657]: Not of type "Battery", skipping.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27659]: /sys/class/power_supply/BAT0 is of type Battery.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27660]: Checking levels for /sys/class/power_supply/BAT0.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27663]: Present: 1.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27665]: Remaining charge: 2101000
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27667]: Full capacity: 5591000
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27669]: Laptop mode
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27670]: Checking if desired state is different from current state.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27671]: enabled, active
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27672]: Module /usr/share/laptop-mode-tools/modules/ac97-powersave is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27673]: Module /usr/share/laptop-mode-tools/modules/battery-level-polling is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27674]: Module /usr/share/laptop-mode-tools/modules/bluetooth is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27675]: Module /usr/share/laptop-mode-tools/modules/configuration-file-control is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27676]: Module /usr/share/laptop-mode-tools/modules/cpufreq is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27677]: Module /usr/share/laptop-mode-tools/modules/dpms-standby is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27678]: Module /usr/share/laptop-mode-tools/modules/eee-superhe is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27679]: Module /usr/share/laptop-mode-tools/modules/ethernet is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27680]: Module /usr/share/laptop-mode-tools/modules/exec-commands is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27681]: Module /usr/share/laptop-mode-tools/modules/hal-polling is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27682]: Module /usr/share/laptop-mode-tools/modules/hdparm is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27683]: Module /usr/share/laptop-mode-tools/modules/intel-hda-powersave is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27684]: Module /usr/share/laptop-mode-tools/modules/intel-sata-powermgmt is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27685]: Module /usr/share/laptop-mode-tools/modules/laptop-mode is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27686]: Module /usr/share/laptop-mode-tools/modules/lcd-brightness is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27687]: Module /usr/share/laptop-mode-tools/modules/nmi-watchdog is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27688]: Module /usr/share/laptop-mode-tools/modules/runtime-pm is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27689]: Module /usr/share/laptop-mode-tools/modules/sched-mc-power-savings is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27690]: Module /usr/share/laptop-mode-tools/modules/sched-smt-power-savings is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27691]: Module /usr/share/laptop-mode-tools/modules/start-stop-programs is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27692]: Module /usr/share/laptop-mode-tools/modules/syslog-conf is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27693]: Module /usr/share/laptop-mode-tools/modules/terminal-blanking is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27694]: Invoking module /usr/share/laptop-mode-tools/modules/usb-autosuspend.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27706]: Enabling autosuspend mode for USBCORE Controller, with timeout 2.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27707]: Module /usr/share/laptop-mode-tools/modules/video-out is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27709]: Module /usr/share/laptop-mode-tools/modules/wireless-ipw-power is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27714]: Enabling auto suspend mode for usb device 1-1.2.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27713]: Module /usr/share/laptop-mode-tools/modules/wireless-iwl-power is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27715]: Module /usr/share/laptop-mode-tools/modules/wireless-power is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27717]: Module /usr/local/lib/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27716]: Enabling auto power level for usb device 1-1.2.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27718]: Module /usr/local/share/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27719]: Module /etc/laptop-mode/modules/* is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27722]: On battery power: Activating, because ENABLE_LAPTOP_MODE_ON_BATTERY is set.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27724]: Not on AC and we have battery information in /sys/class/power_supply/BAT* -- checking minimum battery charge.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27726]: /sys/class/power_supply/ADP1 is of type Mains.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27727]: Not of type "Battery", skipping.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27729]: /sys/class/power_supply/BAT0 is of type Battery.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27730]: Checking levels for /sys/class/power_supply/BAT0.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27732]: Present: 1.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27734]: Remaining charge: 2101000
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27736]: Full capacity: 5591000
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27738]: Laptop mode
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27739]: Checking if desired state is different from current state.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27740]: enabled, active
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27741]: Module /usr/share/laptop-mode-tools/modules/ac97-powersave is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27742]: Module /usr/share/laptop-mode-tools/modules/battery-level-polling is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27743]: Module /usr/share/laptop-mode-tools/modules/bluetooth is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27744]: Module /usr/share/laptop-mode-tools/modules/configuration-file-control is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27745]: Module /usr/share/laptop-mode-tools/modules/cpufreq is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27746]: Module /usr/share/laptop-mode-tools/modules/dpms-standby is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27747]: Module /usr/share/laptop-mode-tools/modules/eee-superhe is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27748]: Module /usr/share/laptop-mode-tools/modules/ethernet is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27749]: Module /usr/share/laptop-mode-tools/modules/exec-commands is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27750]: Module /usr/share/laptop-mode-tools/modules/hal-polling is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27751]: Module /usr/share/laptop-mode-tools/modules/hdparm is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27752]: Module /usr/share/laptop-mode-tools/modules/intel-hda-powersave is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27753]: Module /usr/share/laptop-mode-tools/modules/intel-sata-powermgmt is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27754]: Module /usr/share/laptop-mode-tools/modules/laptop-mode is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27755]: Module /usr/share/laptop-mode-tools/modules/lcd-brightness is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27756]: Module /usr/share/laptop-mode-tools/modules/nmi-watchdog is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27757]: Module /usr/share/laptop-mode-tools/modules/runtime-pm is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27758]: Module /usr/share/laptop-mode-tools/modules/sched-mc-power-savings is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27759]: Module /usr/share/laptop-mode-tools/modules/sched-smt-power-savings is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27760]: Module /usr/share/laptop-mode-tools/modules/start-stop-programs is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27761]: Module /usr/share/laptop-mode-tools/modules/syslog-conf is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27762]: Module /usr/share/laptop-mode-tools/modules/terminal-blanking is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27764]: Invoking module /usr/share/laptop-mode-tools/modules/usb-autosuspend.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27776]: Enabling autosuspend mode for USBCORE Controller, with timeout 2.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27777]: Module /usr/share/laptop-mode-tools/modules/video-out is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27780]: Module /usr/share/laptop-mode-tools/modules/wireless-ipw-power is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27781]: Module /usr/share/laptop-mode-tools/modules/wireless-iwl-power is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27782]: Module /usr/share/laptop-mode-tools/modules/wireless-power is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27785]: Not enabling auto suspend mode for usb device 1-1.2:1.0
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27786]: Module /usr/local/lib/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27787]: Not enabling auto power level for usb device 1-1.2:1.0
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27788]: Module /usr/local/share/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:30:54 ryan-linux-desktop laptop-mode[27789]: Module /etc/laptop-mode/modules/* is not executable or is to be skipped.
    Feb 05 17:31:12 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: setting latency timer to 64
    Feb 05 17:31:12 ryan-linux-desktop kernel: usb 1-1.2: USB disconnect, device number 5
    Feb 05 17:31:24 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: setting latency timer to 64
    Feb 05 17:31:25 ryan-linux-desktop kernel: usb 1-1.2: new high-speed USB device number 6 using ehci_hcd
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28069]: Warning: Configuration file /etc/laptop-mode/conf.d/board-specific/* is not readable, skipping.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28070]: Warning: Configuration file /etc/laptop-mode/conf.d/board-specific/* is not readable, skipping.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28083]: Determining power state from /sys/class/power_supply/ADP1/online.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28084]: Determining power state from /sys/class/power_supply/ADP1/online.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28090]: Not trying other options, already found a power supply.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28089]: Not trying other options, already found a power supply.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28106]: Battery level polling is disabled.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28110]: Battery level polling is disabled.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28111]: Prelim lock acquisition on descriptor 8 with pid 28062
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28113]: Couldn't acquire prelim lock on descriptor 8 with pid 28064
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28116]: Prelim lock acquisition on descriptor 9 with pid 28062
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28118]: Now invoking lmt_main_function with arguments -- force
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28119]: Couldn't acquire prelim lock on descriptor 9 with pid 28064
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28121]: Now invoking lock_retry with arguments -- force
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28124]: On battery power: Activating, because ENABLE_LAPTOP_MODE_ON_BATTERY is set.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28127]: Not on AC and we have battery information in /sys/class/power_supply/BAT* -- checking minimum battery charge.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28129]: /sys/class/power_supply/ADP1 is of type Mains.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28130]: Not of type "Battery", skipping.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28132]: /sys/class/power_supply/BAT0 is of type Battery.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28133]: Checking levels for /sys/class/power_supply/BAT0.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28135]: Present: 1.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28137]: Remaining charge: 2076000
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28139]: Full capacity: 5591000
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28141]: Laptop mode
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28142]: Checking if desired state is different from current state.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28144]: enabled, active
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28145]: Module /usr/share/laptop-mode-tools/modules/ac97-powersave is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28146]: Module /usr/share/laptop-mode-tools/modules/battery-level-polling is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28147]: Module /usr/share/laptop-mode-tools/modules/bluetooth is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28148]: Module /usr/share/laptop-mode-tools/modules/configuration-file-control is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28149]: Module /usr/share/laptop-mode-tools/modules/cpufreq is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28150]: Module /usr/share/laptop-mode-tools/modules/dpms-standby is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28151]: Module /usr/share/laptop-mode-tools/modules/eee-superhe is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28152]: Module /usr/share/laptop-mode-tools/modules/ethernet is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28153]: Module /usr/share/laptop-mode-tools/modules/exec-commands is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28154]: Module /usr/share/laptop-mode-tools/modules/hal-polling is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28155]: Module /usr/share/laptop-mode-tools/modules/hdparm is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28156]: Module /usr/share/laptop-mode-tools/modules/intel-hda-powersave is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28157]: Module /usr/share/laptop-mode-tools/modules/intel-sata-powermgmt is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28158]: Module /usr/share/laptop-mode-tools/modules/laptop-mode is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28159]: Module /usr/share/laptop-mode-tools/modules/lcd-brightness is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28160]: Module /usr/share/laptop-mode-tools/modules/nmi-watchdog is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28161]: Module /usr/share/laptop-mode-tools/modules/runtime-pm is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28162]: Module /usr/share/laptop-mode-tools/modules/sched-mc-power-savings is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28163]: Module /usr/share/laptop-mode-tools/modules/sched-smt-power-savings is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28164]: Module /usr/share/laptop-mode-tools/modules/start-stop-programs is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28165]: Module /usr/share/laptop-mode-tools/modules/syslog-conf is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28166]: Module /usr/share/laptop-mode-tools/modules/terminal-blanking is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28167]: Invoking module /usr/share/laptop-mode-tools/modules/usb-autosuspend.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28179]: Enabling autosuspend mode for USBCORE Controller, with timeout 2.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28180]: Module /usr/share/laptop-mode-tools/modules/video-out is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28183]: Module /usr/share/laptop-mode-tools/modules/wireless-ipw-power is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28185]: Module /usr/share/laptop-mode-tools/modules/wireless-iwl-power is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28187]: Module /usr/share/laptop-mode-tools/modules/wireless-power is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28188]: Module /usr/local/lib/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28190]: Module /usr/local/share/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28189]: Enabling auto suspend mode for usb device 1-1.2.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28191]: Module /etc/laptop-mode/modules/* is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28192]: Enabling auto power level for usb device 1-1.2.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28195]: On battery power: Activating, because ENABLE_LAPTOP_MODE_ON_BATTERY is set.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28197]: Not on AC and we have battery information in /sys/class/power_supply/BAT* -- checking minimum battery charge.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28199]: /sys/class/power_supply/ADP1 is of type Mains.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28200]: Not of type "Battery", skipping.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28202]: /sys/class/power_supply/BAT0 is of type Battery.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28203]: Checking levels for /sys/class/power_supply/BAT0.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28205]: Present: 1.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28207]: Remaining charge: 2076000
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28209]: Full capacity: 5591000
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28211]: Laptop mode
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28212]: Checking if desired state is different from current state.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28213]: enabled, active
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28214]: Module /usr/share/laptop-mode-tools/modules/ac97-powersave is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28215]: Module /usr/share/laptop-mode-tools/modules/battery-level-polling is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28216]: Module /usr/share/laptop-mode-tools/modules/bluetooth is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28217]: Module /usr/share/laptop-mode-tools/modules/configuration-file-control is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28218]: Module /usr/share/laptop-mode-tools/modules/cpufreq is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28219]: Module /usr/share/laptop-mode-tools/modules/dpms-standby is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28220]: Module /usr/share/laptop-mode-tools/modules/eee-superhe is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28221]: Module /usr/share/laptop-mode-tools/modules/ethernet is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28223]: Module /usr/share/laptop-mode-tools/modules/exec-commands is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28224]: Module /usr/share/laptop-mode-tools/modules/hal-polling is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28225]: Module /usr/share/laptop-mode-tools/modules/hdparm is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28226]: Module /usr/share/laptop-mode-tools/modules/intel-hda-powersave is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28227]: Module /usr/share/laptop-mode-tools/modules/intel-sata-powermgmt is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28228]: Module /usr/share/laptop-mode-tools/modules/laptop-mode is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28229]: Module /usr/share/laptop-mode-tools/modules/lcd-brightness is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28230]: Module /usr/share/laptop-mode-tools/modules/nmi-watchdog is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28231]: Module /usr/share/laptop-mode-tools/modules/runtime-pm is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28232]: Module /usr/share/laptop-mode-tools/modules/sched-mc-power-savings is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28233]: Module /usr/share/laptop-mode-tools/modules/sched-smt-power-savings is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28234]: Module /usr/share/laptop-mode-tools/modules/start-stop-programs is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28235]: Module /usr/share/laptop-mode-tools/modules/syslog-conf is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28236]: Module /usr/share/laptop-mode-tools/modules/terminal-blanking is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28237]: Invoking module /usr/share/laptop-mode-tools/modules/usb-autosuspend.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28245]: Enabling autosuspend mode for USBCORE Controller, with timeout 2.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28254]: Module /usr/share/laptop-mode-tools/modules/video-out is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28255]: Not enabling auto suspend mode for usb device 1-1.2:1.0
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28256]: Not enabling auto power level for usb device 1-1.2:1.0
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28257]: Module /usr/share/laptop-mode-tools/modules/wireless-ipw-power is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28258]: Module /usr/share/laptop-mode-tools/modules/wireless-iwl-power is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28259]: Module /usr/share/laptop-mode-tools/modules/wireless-power is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28260]: Module /usr/local/lib/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28261]: Module /usr/local/share/laptop-mode-tools/modules/* is not executable or is to be skipped.
    Feb 05 17:31:25 ryan-linux-desktop laptop-mode[28262]: Module /etc/laptop-mode/modules/* is not executable or is to be skipped.
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1d.0: setting latency timer to 64
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1d.0: setting latency timer to 64
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1d.0: remove, state 4
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb usb2: USB disconnect, device number 1
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb 2-1: USB disconnect, device number 2
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1d.0: USB bus 2 deregistered
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: setting latency timer to 64
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: setting latency timer to 64
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: remove, state 4
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb usb1: USB disconnect, device number 1
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb 1-1: USB disconnect, device number 2
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb 1-1.1: USB disconnect, device number 3
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb 1-1.2: USB disconnect, device number 6
    Feb 05 17:31:41 ryan-linux-desktop kernel: usb 1-1.3: USB disconnect, device number 4
    Feb 05 17:31:41 ryan-linux-desktop kernel: ehci_hcd 0000:00:1a.0: USB bus 1 deregistered
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU3: Package power limit notification (total events = 81)
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU1: Package power limit notification (total events = 81)
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU2: Package power limit notification (total events = 81)
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU0: Package power limit notification (total events = 81)
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU1: Package power limit normal
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU2: Package power limit normal
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU3: Package power limit normal
    Feb 05 17:34:03 ryan-linux-desktop kernel: CPU0: Package power limit normal
    Feb 05 17:37:56 ryan-linux-desktop sudo[31776]: root : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe -r xhci_hcd
    Feb 05 17:37:56 ryan-linux-desktop sudo[31776]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:37:56 ryan-linux-desktop sudo[31776]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:37:59 ryan-linux-desktop sudo[31810]: root : TTY=pts/2 ; PWD=/home/ryanvade ; USER=root ; COMMAND=/sbin/modprobe xhci_hcd
    Feb 05 17:37:59 ryan-linux-desktop sudo[31810]: pam_unix(sudo:session): session opened for user root by ryanvade(uid=0)
    Feb 05 17:37:59 ryan-linux-desktop sudo[31810]: pam_unix(sudo:session): session closed for user root
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU1: Package power limit notification (total events = 125)
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU0: Package power limit notification (total events = 125)
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU2: Package power limit notification (total events = 125)
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU3: Package power limit notification (total events = 125)
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU1: Package power limit normal
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU3: Package power limit normal
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU2: Package power limit normal
    Feb 05 17:44:12 ryan-linux-desktop kernel: CPU0: Package power limit normal
    A new kernel was just installed via pacman.  I haven't booted it yet.  Maybe that will fix it?
    EDIT: This is happening with kernel 3.7.6-1-ARCH.  Especially after the computer goes to sleep.
    Last edited by ryanvade (2013-02-21 22:51:29)

    Well 2.0 ports work now.
    3.0 works for a few seconds, then stops.
    [ 302.762355] xhci_hcd 0000:00:14.0: setting latency timer to 64
    [ 302.762468] xhci_hcd 0000:00:14.0: remove, state 84
    [ 302.775661] usb usb4: USB disconnect, device number 1
    [ 302.776021] xHCI xhci_drop_endpoint called for root hub
    [ 302.776030] xHCI xhci_check_bandwidth called for root hub
    [ 302.776377] xhci_hcd 0000:00:14.0: USB bus 4 deregistered
    [ 302.776396] xhci_hcd 0000:00:14.0: remove, state 1
    [ 302.878776] hub 3-0:1.0: activate --> -108
    [ 302.878841] usb usb3: USB disconnect, device number 1
    [ 302.879119] xHCI xhci_drop_endpoint called for root hub
    [ 302.879124] xHCI xhci_check_bandwidth called for root hub
    [ 302.879533] xhci_hcd 0000:00:14.0: USB bus 3 deregistered
    [ 314.069077] xhci_hcd 0000:00:14.0: setting latency timer to 64
    [ 314.069093] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 314.069116] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
    [ 314.069277] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 314.069304] xhci_hcd 0000:00:14.0: irq 21, io mem 0x74600000
    [ 314.069409] xhci_hcd 0000:00:14.0: irq 42 for MSI/MSI-X
    [ 314.069910] xHCI xhci_add_endpoint called for root hub
    [ 314.069919] xHCI xhci_check_bandwidth called for root hub
    [ 314.070031] hub 3-0:1.0: USB hub found
    [ 314.070051] hub 3-0:1.0: 4 ports detected
    [ 314.080764] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 314.080774] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
    [ 314.081037] xHCI xhci_add_endpoint called for root hub
    [ 314.081040] xHCI xhci_check_bandwidth called for root hub
    [ 314.081089] hub 4-0:1.0: USB hub found
    [ 314.081099] hub 4-0:1.0: 4 ports detected
    [ 314.430506] usb 3-4: new low-speed USB device number 2 using xhci_hcd
    [ 314.450307] usb 3-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 314.450325] usb 3-4: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 314.454047] input: GE 98134 GE 98134 as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input20
    [ 314.454371] hid-generic 0003:05B8:3155.0007: input,hidraw0: USB HID v1.00 Keyboard [GE 98134 GE 98134] on usb-0000:00:14.0-4/input0
    [ 314.459555] input: GE 98134 GE 98134 as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.1/input/input21
    [ 314.460089] hid-generic 0003:05B8:3155.0008: input,hiddev0,hidraw1: USB HID v1.00 Mouse [GE 98134 GE 98134] on usb-0000:00:14.0-4/input1
    [ 341.130120] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 1 ep 0 with no TDs queued?
    Something else I noticed was that when I unplug the power cable to my laptop, the USB 3.0 stops and I get this in dmesg right after:
    [ 609.467318] EXT4-fs (sda6): re-mounted. Opts: data=ordered,commit=600
    [ 609.485639] EXT4-fs (sda5): re-mounted. Opts: data=ordered,commit=600
    [ 609.988234] EXT4-fs (sda6): re-mounted. Opts: data=ordered,commit=600
    [ 610.072949] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 0 with no TDs queued?
    [ 610.097739] EXT4-fs (sda5): re-mounted. Opts: data=ordered,commit=600
    [ 610.664363] EXT4-fs (sda6): re-mounted. Opts: data=ordered,commit=600
    [ 610.737512] EXT4-fs (sda5): re-mounted. Opts: data=ordered,commit=600
    *NOTE is it possible to install the 3.8-rc kernel through yaourt? I have tried to compile it myself using old config and it never works.  EVER.
    Last edited by ryanvade (2013-02-10 06:27:42)

  • HT1338 MiniDVI port suddenly stopped working

    I first thought my external monitor or HDMI cable stopped working, but when I tried with my iMac, I realized it must be the port on the MacBookPro. I upgraded to Mountain Lion about a week ago and the external worked until this morning. Anyone else have trouble, or should I assume the port went bad? 15" late-2011 MBP.

    Not sure if your advice is what fixed my port or not... I tried reseting the parameter RAM but nothing happened like you explained. I looked on Apple’s site on how to reset it, and their instructions were pretty much just as you described. (Except there were supposed to be two chimes and not three). Ithink pressing commandoption+pr had some kind of effect because the computer seemed to take longer to start up than usual. Unfortunately the USB port at this point still doesn’t work.
    Finally I decided to take off the back panel, thinking maybe one of the gold pins on the Mobo were some kind of ground, and that they somehow (at-least one of them) were no longer grounding. I put the computer back together and start it up... And YES! the USB port works again!
    You think it was a grounding issue? Or did I just need to take out the battery for several minuets?

  • Ssh Port Forwarding Stopped Working

    I have used ssh port forwarding in the past, and it has come in handy.
    I have recently upgraded to Mavericks, but it does appear that my ssh port forwarding stopped some time before this. The last time I know it worked was 5/14/14, and feel it has worked more recently as well.
    Here's what I do, from my Mac I ssh to my work jump server (port 22, let's say its IP is 11.22.33.44), and my jump server has access to work PC (lets say IP of 10.1.2.3). My work PC has RDP running on it on the common port 3389. I have verified that I can set up a working RDP session at work from another box. Also, I know that my jump server can get to my PC at work as I can ping my work IP if I just ssh straight to my jump server. And I know that there is no firewall stopping me from the jump server as I can also open a telnet session to my work PC on port 3389, without errors.
    So, here's how I have done it in the past and it has worked, but now recently stopped working in Terminal app:
    ssh  -f  [email protected]  -L  3388:10.1.2.3:3389  -Nnv
    The verbose logging shows that it sets up connectivity. If I then look to see if my local port is listening I can type:
    netstat  -an  |  grep  127.0
    I will note that port 3387 is in fact LISTENing and waiting for connection
    I then start my RDP client app, and start a session to "localhost:3387" (I could also use "127.0.0.1:3387", and have, but it does not work either). My RDP client eventually times out. I have turned my firewall off and on, neither way works.
    Does anyone know why this may have stopped working?
    Your input is most appreciated.
    The verbose log shows the following is setup appropriately (with noted modifications to server names and actual IPs):
    debug1: Authentication succeeded (keyboard-interactive).
    Authenticated to somewhere.net ([11.22.33.44]:22).
    debug1: Local connections to localhost:3387 forwarded to remote address 10.1.2.3:3389
    debug1: Local forwarding listening on 127.0.0.1 port 3387.

    Unfortunately I don't have another device to test if RDP is working on my LAN, however, when I check out my network connections and this is what I see after setting up the ssh tunnel and prior to attempting the RDP connection (again names protected):
    my-rmbp:~ me2$ netstat -an | grep 127.0
    tcp4       0      0  127.0.0.1.3387         *.*                    LISTEN
    Then, as it is difficult to catch in the middle of TCP 3-way handshaking, here's what happens after an attempt with the RDP client while it sits and spins:
    my-rmbp:~ me2$ netstat -an | grep 127.0
    tcp4       0      0  127.0.0.1.3387         127.0.0.1.50323        FIN_WAIT_2
    tcp4       0      0  127.0.0.1.50323        127.0.0.1.3387         CLOSE_WAIT
    tcp4       0      0  127.0.0.1.3387         *.*                    LISTEN
    You can clearly see it's attempting to make a connection over the tunnel via my RDP client, but it's being shut down right away. I will obtain a WireShark packet capture and see exactly what's happening. Oh, and if I tried to RDP to a port other than the one I set up the port forwarding tunnel with, RDP would disconnect right away.
    What I'm most interested in is why, without any known changes, other than OS updates, did this work a few months ago, and now it does not?
    I have also tried other test ssh port forwarding, such as to www.apple.com forwarding 8080 on localhost to 80, and others, and none of those work either with web browsers, I assume this is something Apple has done to disable ssh port forwarding/tunneling. Perhaps someone else has bumped into this and found a fix? Please share!
    Also, I have heard that you have to be root in order to set up port forwarding, but clearly this is not accurate, as it worked before, and also as you can see above it worked without root. But I tried both ways, and sadly neither worked.
    Could it by my jump server? Possibly, but others at work do this and it works just fine for them from their Windoze PCs. So can't be that either.
    Perhaps my capture will tell me, I'll report back here with what I discover. Thanks in advance!

Maybe you are looking for