RVS4000 since firmware upgrade no IAC

Hello, since upgrading to the latest firmware V2.0.3.4 I can no longer access the "Forbidden Domains" field in the Website Blocking by URL Address section of the page. The field is greyed out. Tried several web browsers I.E., firefox, chrome, safari...
Thanks in advance for any tips.

A *#7370# format fixed the issue.

Similar Messages

Cooler running since firmware upgrade

Has any body else noticed a significant decrease in running temps since the firmware upgrade? I can now use it as a LAP top computer, whereas before it reguired a cooling pad just to use.
17" MacBook Pro
G4 1 Gig - Digital Audio Mac OS X (10.4.6)

Like tcdm said, the timer is based on the rate of drainage at that particular moment. Think of the timer being like the battery indicator of the ipod. On hard drive-based ipods, the battery indicator can tend to make a quick plummet when accessing music or larger files like movies. The battery is basically telling you how much is left based on the rate of power usage at that particular moment, but then when the hard disk stops spinning the indicator jumps back up with just a little taken away. If you see 5 hours at one moment, accessing large files(which kicks the HDD into motion) will suddenly put you at a little less. I set a stop watch on my macbook while it played a movie in MPEG-4 format. after playing movies continuously from full charge to near empty i got about 4 hours (roughly 3:53 by my watch) I count the time from full charge to the moment i get the first battery low warning. after that its just a few minutes before the computer sleeps to decrease the rate of power usage. So far no big changes as far as i can see, I think this firmware update mostly addresses the issue regarding the cooling system readings rather than energy efficiency, but who knows.

HDMI output not working since firmware upgrade

I would appreciate troubleshooting tips for getting the HDMI output to work. I just tried it recently for the first time in a long while, approximately 4 weeks after doing the firmware update to 2.2. When I did it before, plugging in the HDMI cable would automatically start output to my HD TV. Now that is no longer the case. Changing the HDMI output from "Auto" to "720p" does not make a difference either.
Otherwise, everything works well and I've been satisfied with my Creative 7 to date. I have installed several apps so it could be that there is a conflict and nothing related to the firmware upgrade.
Any troubleshooting suggestions would be appreciated.

Well I've received my refurbished device for about a week now. The HDMI still doesn't work either with Zii Video or a 3rd party app MoboPlayer. ?I am tempted to reinstall the firmware upgrade again. Is it ok to try this or is it only a one time attempt?
Perhaps this should be a separate thread but are any of the "Phone 2 SD" apps compatible with the Ziio 7? Whenever I use the "Move to SD card" option, there is still no program moved to the external SD card. ?I have a Ziio 7 with 6 GB of memory as well as a 6GB micro SD card. ?My memory settings are:
- SD Card: total space - 5.43GB; Available space - 5.43GB
- Device media storage: Total space - 2.48GB; Available Space - 2.3 GB
- System storage: Total Space - .97 GB; Available space - .59GB
In Settings>Applications>Manage Applications, the "On SD Card" tab lists several programs lists several apps but none of them are actually on the external SD card.

Amazing improvements since firmware upgrade

Hi, I have had a pretty much trouble free (i still have an annoying CPU whine that applestore says is just my young ears being sensitive. Im 20 not stupid!!)
macbook, week 35.
I updated the firmware and now it runs VERY cool, and the battery life has become amazing!!!
4 hours-4 hours 20 mins, running full brightness and on airport connection.
It used to max out at 2.5 hours..
Also the sound is louder through the speakers.
Also, can I just say WOW I installed windows xp with bootcamp and it is AMAZINGLY fast. I did it for my games,
and the graphics card seems to handle the sims 2 perfectly at high settings.
It looks great!!
SO in my opinion the firmware upgrade gets the thumbs up!!

Like tcdm said, the timer is based on the rate of drainage at that particular moment. Think of the timer being like the battery indicator of the ipod. On hard drive-based ipods, the battery indicator can tend to make a quick plummet when accessing music or larger files like movies. The battery is basically telling you how much is left based on the rate of power usage at that particular moment, but then when the hard disk stops spinning the indicator jumps back up with just a little taken away. If you see 5 hours at one moment, accessing large files(which kicks the HDD into motion) will suddenly put you at a little less. I set a stop watch on my macbook while it played a movie in MPEG-4 format. after playing movies continuously from full charge to near empty i got about 4 hours (roughly 3:53 by my watch) I count the time from full charge to the moment i get the first battery low warning. after that its just a few minutes before the computer sleeps to decrease the rate of power usage. So far no big changes as far as i can see, I think this firmware update mostly addresses the issue regarding the cooling system readings rather than energy efficiency, but who knows.

WAP321 Dropping Connection since firmware Upgrade

MyWAP321 is dropping connections at least once a day since upgradiing to firmware 1.0.1.10. before the upgrade I had no problems and I have another WAP321 with firmware 1.0.0.3 that never drops connection. Is anybody else having this problem since upgrading?

Hi ,
Ive just installed this WAP 321 wiht Radius server authentication.
I have the firmware version 1.0.2.3 and this WAP is now having Connection dropout and dosent connect again.
I have to do re try for several times and again it starts working.
Please see the log and advice me what is happeing inside it and why this connection is not staying persistent with the associated wireless clients.
Jun 9 2013 20:07:25
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:04:36
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:04:36
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:04:35
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:04:35
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:04:17
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:04:17
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:04:16
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:04:16
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:00:56
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:00:56
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:00:53
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:00:53
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:00:52
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:00:52
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 02:00:52
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 02:00:52
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 01:59:22
info
hostapd[1241]
authenticated - identity '' EAP type: 25 (PEAP)
Jun 9 2013 01:59:22
info
hostapd[1241]
The wireless client with MAC address 8c:70:5a:47:b9:ac has been successfully authenticated.
Jun 9 2013 01:59:22
info
hostapd[1241]
wlan0: WPA STA 8c:70:5a:47:b9:ac pairwise key exchange completed (WPAv2)
Jun 9 2013 01:59:22
info
hostapd[1241]
EAP authentication with the authentication server completed
Jun 9 2013 01:59:22
info
hostapd[1241]
wlan0: IEEE 802.11 STA 8c:70:5a:47:b9:ac associated with BSSID d8:67:d9:d1:e9:20
Jun 9 2013 01:59:22
info
hostapd[1241]
wlan0: IEEE 802.11 Assoc request from 8c:70:5a:47:b9:ac BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:59:21
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 01:59:21
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 01:59:20
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 01:59:20
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 01:59:18
debug
clusterd[1114]
dman sent notification that config has changed
Jun 9 2013 01:59:18
info
dman[874]
The AP startup configuration was updated successfully.
Jun 9 2013 01:57:27
info
hostapd[1106]
authenticated - identity '' EAP type: 25 (PEAP)
Jun 9 2013 01:57:27
info
hostapd[1106]
The wireless client with MAC address 8c:70:5a:47:b9:ac has been successfully authenticated.
Jun 9 2013 01:57:27
info
hostapd[1106]
wlan0: WPA STA 8c:70:5a:47:b9:ac pairwise key exchange completed (WPAv2)
Jun 9 2013 01:57:27
info
hostapd[1106]
EAP authentication with the authentication server completed
Jun 9 2013 01:57:27
info
hostapd[1106]
wlan0: IEEE 802.11 STA 8c:70:5a:47:b9:ac associated with BSSID d8:67:d9:d1:e9:20
Jun 9 2013 01:57:27
info
hostapd[1106]
wlan0: IEEE 802.11 Assoc request from 8c:70:5a:47:b9:ac BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:57:27
info
hostapd[1106]
wlan0: IEEE 802.11 STA 8c:70:5a:47:b9:ac deauthed from BSSID d8:67:d9:d1:e9:20 reason 3: STA is leaving IBSS or ESS
Jun 9 2013 01:57:27
info
hostapd[1106]
wlan0: IEEE 802.11 Assoc request from 8c:70:5a:47:b9:ac BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:57:27
info
hostapd[1106]
wlan0: IEEE 802.11 STA 8c:70:5a:47:b9:ac deauthed from BSSID d8:67:d9:d1:e9:20 reason 3: STA is leaving IBSS or ESS
Jun 9 2013 01:55:39
info
hostapd[1106]
wlan0: IEEE 802.11 Assoc request from 68:09:27:a0:0c:6e BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:55:39
info
hostapd[1106]
wlan0: IEEE 802.11 STA 68:09:27:a0:0c:6e deauthed from BSSID d8:67:d9:d1:e9:20 reason 3: STA is leaving IBSS or ESS
Jun 9 2013 01:55:39
info
hostapd[1106]
wlan0: IEEE 802.11 Assoc request from 68:09:27:a0:0c:6e BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:55:39
info
hostapd[1106]
wlan0: IEEE 802.11 STA 68:09:27:a0:0c:6e deauthed from BSSID d8:67:d9:d1:e9:20 reason 3: STA is leaving IBSS or ESS
Jun 9 2013 01:55:38
info
hostapd[1106]
wlan0: IEEE 802.11 Assoc request from 68:09:27:a0:0c:6e BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:55:38
info
hostapd[1106]
wlan0: IEEE 802.11 STA 68:09:27:a0:0c:6e deauthed from BSSID d8:67:d9:d1:e9:20 reason 3: STA is leaving IBSS or ESS
Jun 9 2013 01:55:38
info
hostapd[1106]
wlan0: IEEE 802.11 Assoc request from 68:09:27:a0:0c:6e BSSID d8:67:d9:d1:e9:20 SSID ADRJSLEDFIWMDWOQFDFPE
Jun 9 2013 01:55:38
info
hostapd[1106]
wlan0: IEEE 802.11 STA 68:09:27:a0:0c:6e deauthed from BSSID d8:67:d9:d1:e9:20 reason 3: STA is leaving IBSS or ESS

Nokia E52 email issue since firmware upgrade (031....

Hi guys,
Yesterday i successfully upgraded my E52 to latest firmware - 031.012. After upgrade i removed all previous email accounts (1 MFE, 1 pop and 1 imap) and start a new setup.
i have to mention, that i double checked that the email client version has updated to 2.1.0 (the old one was 2.0.5). There are also several visual changes during the email setup.
Now here is my issue: I recreated my exchange email account and it works perfectly, but when i try to add a second email account (Email->New), choose one of the providers from the list (Windows Live for example) and proceed here is what happens:
1. I get a promt to enter email address and password
2.Then "Validating settings" and "Downloading terms" progress bars start
3. After "Downloading terms" progress bar completes i am returned at the page where have to choose email provider again
Is there someone with similar issue as mine when has upgraded to 031.012? I hope someone will give me a clue how to fix it...
Thx in advance!
Regards,
Emil

On E52 or E72 (I haven't checked on other handsets), The problem occurs only if you try to add an account which is previously registered on Nokia Messaging Website http://email.nokia.com/ or has been added as an additional account within the Nokia Messaging Account.
Before adding/creating a new email account on E52 or E72, make sure the account has not been registered at Nokia Messaging Website or if it has been registered then make sure to delete those accounts before you add them in your phone newly.
You can delete account from Nokia Messaging Website by logging in with that account first on the website.
Remember that you have two ways to remove the account from Nokia Messaging Website.
1- If the account was used initially to signup on the website (actual Nokia Messaging Account) then you need to login with that account and Cancel the membership. It will delete all the additional accounts if you have added any.
2- If the account was added as an additional account in an existing Nokia Messaging Account, then again you would need to login with the Nokia Messaging Account and delete the account from the list as needed.
Note: If you are wandering that you never manually registered on the above website by visiting it on your computer, then keep in mind that the account is automatically registered on the website when you try to add or create the account on the Nokia Email Client on your phone. This could probably be the case that you would have registered once in the past via your Nokia Email client or directly on the Website. In either case you would need to remove the accounts from the Nokia Messaging.
I haven't read this any where but this is what I have got during fixing and finding the solution. I have created accounts on E52 (more than once after upgrading firmwares) very easily by following the above procedure. What ever it is, a bug? or an intentional reason, I don't know.
I hope it could fix your problems with the New Nokia Email client built-in with E52
Edit:-----
Note1: You would have to wait for a few minutes after removing the accounts from the Nokia Messaging Website, before trying to add in your phone.
Note2: First add the Ovi Mail Account(make sure you have it signed-up and configured on http://www.ovi.com/) in your phone and then add any of the other accounts later.

Link problem since firmware upgrade

Hi,
Just upgraded to latest firmware on ix4-300d, link doesn't work anymore!!!
Any idea?
Thanks
Solved!
Go to Solution.

Are you using the old Iomega Link or the new LenovoEMC Link? I would recommend downloading the LenovoEMC link if you haven't: LenovoEMC Link iOS and Android application
Have you enabled port forwarding on your router? You might need to. Check to make sure that the ports are forwarded correctly: Why can't I connect remotely to my Iomega device or Personal Cloud from my Iomega Link App?
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

PLOGI errors & warnings since firmware upgrade on Brocade Director 48000

Hi there,
I have a SFE25K with several domains. Some domains with Solaris 9 and others with Solaris 10. They have ISP2312 HBAs with firmware from 1.14.09 to 1.14.15, these are connected to a Director 4800 with the following version info:
Kernel: 2.4.19
Fabric OS: v5.1.0d
Made on: Tue Aug 8 18:35:50 2006
Flash: Thu Nov 23 23:17:35 2006
BootProm: 4.5.3
The firmware on the switch was recently upgraded without rebooting the switch.
/var/adm/messages on all domains record these messages every half hour:
Feb 15 13:23:39 myhost fp: [ID 517869 kern.info] NOTICE: fp(0): PLOGI to 610c13 failed state=Timeout, reason=Hardware Error
Feb 15 13:23:39 myhost fp: [ID 517869 kern.info] NOTICE: fp(0): PLOGI to 610c13 failed state=Timeout, reason=Hardware Error
Feb 15 13:23:39 myhost fctl: [ID 517869 kern.warning] WARNING: 184561=>fp(0)::PLOGI to 610c13 failed. state=c reason=1.
Feb 15 13:23:39 myhost fctl: [ID 517869 kern.warning] WARNING: 184561=>fp(0)::PLOGI to 610c13 failed. state=c reason=1.
Feb 15 13:53:39 myhost fp: [ID 517869 kern.info] NOTICE: fp(0): PLOGI to 610c13 failed state=Timeout, reason=Hardware Error
Feb 15 13:53:39 myhost fp: [ID 517869 kern.info] NOTICE: fp(0): PLOGI to 610c13 failed state=Timeout, reason=Hardware Error
Feb 15 13:53:39 myhost fctl: [ID 517869 kern.warning] WARNING: 184651=>fp(0)::PLOGI to 610c13 failed. state=c reason=1.
Feb 15 13:53:39 myhost fctl: [ID 517869 kern.warning] WARNING: 184651=>fp(0)::PLOGI to 610c13 failed. state=c reason=1.
In addition, every time we attach a new fiber from the hba to the switch in order to get new disk or tape devices, Solaris does not detect anything until a reconfiguration reboot (reboot -- -r). We tried cfgadm -c configure <dev>, luxadm -e forcelip <dev>, with not success.
Any advice would be appreciated.

Use your service contract.
Open a support case with Sun.
http://www.sun.com/secure/contact/
These forums are not techsupport.
Don't trust the operation of such expensive enterprise class systems
to what some anonymous person tells you in a forum on the Internet.
The forums are for user-to-user discussions.
There is no guarantee on knowledge or experience levels.
(there are some extremely skilled contributors to these discussions,
but there are many novice contributors as well)
If you follow the advice on what someone says here,
and they are mistaken or incomplete in their advice...
You tell your employer: "But those people in the forum told me to do this ..."
Then you will need to go and re-write your resume.
Contact Sun.
Direct techsupport has accountability.
That is why you have that service contract.
With a SF25K in the building, you likely have
an assigned SSE on your account. They may even have
permanent residence in your building. Draw upon their skills and advice.

Apple TV 3 doesn't start Bonjour services after sleep since firmware upgraded to 6.0.2 (6646.81.1 build)

I have upgraded my AppleTV 3 to firmware 6.0.2 for five weeks but always getting problem in Airplay my ipad2 and wired iMac to Apple TV3. Before that, the Apple TV3 in firmware 5.0 was fantastic in everything. Now, the all-time-sympton of my Apple TV3 waking up from sleep is:
1) iPad2 in IOS6..1.3 can't find any airplay icon, same as my new iPhone 5s
2) The wired iMac can't connect to AppleTV3 through Airplay, neither from Maverick's airplay icon nor from iTune's airplay icon.
3) Further than that, the home sharing from AppleTV3 is found to be disconnected from iTune in iMac
My port-scan towards ApplTV3 at this scenario is found all the Bonjour services are missing, including:
* Remote Audio Output (port 5000)
* _airplay (port 7000)
* _touch-able (port 3689)
* Sleep Proxy Server (port 57206)
* _appletv-v2 (port 3689)
My walk around at the moment is to restart AppleTV3, then all the Bonjour services come back and airplay, home sharing work again. However, this requires me to restart the box everytime I bring up the box from sleep. That means I have to turn on TV... quite fustrated.
I'm wondering if there is any similar problem encounted and any fix. Well, I can't find any formal description from Apple but their trouble-shooting document keeps saying to "restart Apple TV" as last resort.
Tks in advance!

I finally found the like-symptom causing the issue of missing airplay services on ATV box.
Well, I have one airport express installed in my study room, which connects to the same LAN as ATV3 in living room. Today, I reset airport express to factory setting and reconfigured everything on AirportExpress, including its SSiD, wifi network key and device password. All of a sudden, my iPad, iPhone, iMac lost their airplay connection to ATV3. Port scanning found no airplay services on ATV3 box. It needed box restart to bring up airplay as my earlier walk around solution. I still performed reset -> restore for a "permanent fix".
That said we might have airplay icon disappeared again if there were more than one airplay device on the same LAN that would interfere to each other. Working on one airplay device from ground start would cause airplay service of another box malfunction.
My experience showed this twice. The first was happened when I put an airport express on the same LAN and I posted a thread here for help. The second was in this morning when i reset airport express to factory setting

I have Lightroom 4.4 and a Nikon d800 with firmware upgrade 2.005. raw files are now since upgrade, unreadable. any plugins or advice? Thanks

I have Lightroom 4.4 and a Nikon d800 with firmware upgrade 2.005. raw files are now since upgrade, unreadable. any plugins or advice? Thanks

I select the images I want uploaded, NEF files, click the "IMPORT" button, process bar comes up and shows work in progress, but no progress. after about 2 minutes, dialogue box appears with message: "unable to import because the following files are unreadable: NEFxxxx, etc."

RVS4000 firmware upgrade to ver 2.0.3.2

Hello,
I have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error' What is causing this?
Curtis

Hi Curtis, the firmware upgrade should be done through the GUI of the RVS4000. If you're able to log in to the device, the upgrade is under admin -> firmware upgrade, then just browse the file and upload it.
-Tom
Please mark answered for helpful posts

Firmware upgrade crippled cp1025nw

LaserJet CP1025nw color: was working flawlessly
received email from HP 4/3/2012, recommending firmware upgrade to v 20120130.
ran upgrade 4/3/2012 from iMac, OS10.6.8.
got error: 'update failed'
print queue says 'printing', cp1025nw doesn't respond.
printer lights: orange triangle enclosed exclamation mark plus green semicircle
This means: fatal error, per the user manual.
manual instructs to turn off, unplug, plug-in, turn on. I did this several times.
printer lights still indicate: fatal error.
HP utility says: device status: unknown, service ID: unknown, FW version: unknown, driver version 2.0.20110727
                  tried to print configuration page: got error 'cannot establish two-way communication with the device'
                  printer and computer are connected with USB cable, (this cable / port communicates without issue to Epson inkjet printer)
Tried printing from Dell laptop: Latitude E6410 with USB cable: Windows XP professional, 2002, service pack 3.
                  has routinely printed from this computer previously.
error message in printer queue: 'error - printing',
Dell said 'found new hardware' tried to install with HP cd-rom
                  error message said 'the hardware was not installed because the wizard cannot find the necessary software'
ran the HP print diagnostic utility HPPDU.exe file from the Dell with USB cable: 'Everything checks out okay with your printer'
print test page: no response from the cp1025nw
What should I try next?

Since my last post I’ve retried the same troubleshooting described before, this time just from the PC. The result is still the same. Lights on the cp1025nw indicate “fatal error”.
Does anyone know how to put this printer into ‘bootcode’ mode? I’ve read about this in some other posts about HP firmware updates trashing printers.
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=...
and
http://www.fixyourownprinter.com/forums/laser/63535
Is there some combination of button presses that sends the printer into bootcode so it is ready to accept the firmware?
HP: How do you start up these printers when they are just manufactured to load the firmware?

IPod Touch skips, stutters, glitches through songs since software upgrade!

Hi everyone,
*Since I upgraded my iPod Touch* to the latest available software update +(for the 1st Gen is 3.1.3)+, it has become *unable to properly play any music encoded above 128kbps*. Before the upgrade, my iPod could play music encoded in any higher bitrates like a champ! All the way to 320kbps, variable, even Apple Lossless format used to play flawlessly.
Suddenly after the last *firmware update*, most of the songs in my iPod Touch would *skip, glitch and garble, making electronic glitches and annoying noises* for no apparent reason. On occasion, the iPod would even *add several second of silence in the middle of random songs*. It's bizarre!
It definitely took me a while to figure it out, and spent weeks testing and researching what could be the problem. It was truly driving me nuts! The result of all these tests was clear: the *iPod Touch now CHOKES on any music file encoded higher than 128 kbps ACC*. Truly pathetic for such an expensive little jukebox. Even the early MP3 players I owned 10 years ago were able to play variable rate MP3 files without a glitch. *_This is a major bug that needs to be solved_*.
For those interested, I did the following tests through my weeks of research to find out the culprit to this problem:
- - - Reinstalled the device software
- - - Reformatted the device, then updated the software
- - - Uninstalled all apps, reinstalled and tested my music after reinstalling each app
- - - Disabled Wi-Fi (no difference)
- - - Copied over my music library from scratch, several times (it was painful)
- - - Reformatted a few albums in different bitrates, from 96kbps, all the way to 320kbps, both in constant and variable rates, and tested them one by one. This took days.
In the end, there is one thing that was consistently clear: *any songs encoded over 128kbps would skip, glitch and sound corrupted. Time after time*. All those music files I had encoded at higher rates +(192 kbps, variable 240 kbps and beyond)+ would make the iPod choke.
There is one temporary solution to this mess, but it involves reducing the quality of your music files: The only way I can now play my music collection in my iPod Touch without skips and glitches is by downconverting my files to the now *obsolete 128kbps*. Only when I converted my music to 128kbps, the annoying skips and glitches stopped. For an audiophile like myself, this was an absolutely painful decision, as I can tell the *obvious loss in quality and nuance in my music files since i had to downconvert them*.
Funny: this skipping problem *also affects any files purchased from iTunes* +(encoded at 240 kbps variable rate)+. Should I ask for my money back, Apple?
I find this irritating and painful, since *the ONE THING the iPod is supposed to do well* (aside from apps, games, and web browsing) *is to PLAY AUDIO AND MUSIC FILES*.
I spent a lot of money on this machine, and until recently it worked like magic; I just wished it played music again like it's supposed to. It's what the iPod was built to do. *Apple: Please fix the software!*
I wonder if there's a forum where I could post my detailed findings, so Apple engineers can take note of this *MAJOR BUG*.
PS: I have recently learned this is a very common bug, and tons of people are reaching out telling me they are experiencing the same annoying problems. Furthermore, *this seems to affect not just the 1st Gen, but ALL generations of the iPod Touch*. It's a *widespread software issue* that was not properly addressed in the latest software upgrade. I'm starting to worry about Apple's quality assurance process.

Hi everyone. Thanks to a tip in another forum, I think I had a breakthrough regarding this problem. I have the strong suspicion it's not the software for the iPod Touch, but instead, the problem comes from *iTunes and how it handles USB 2.0 transfers*.
To make a long story short, all your *music that's encoded above 128 kbps gets corrupted when you transfer it to your Touch from iTunes through your USB 2.0 connection*. That's where the problem is!
I performed this simple test:
*PART 1 - WIFI*
- I connected my iPod Touch via Wi-Fi to the iTunes Store. Bought an album encoded at a very high bitrate (Coldplay's "Viva la Vida", encoded at 256KBPS).
- Downloaded the Coldplay album directly to my iPod Touch via Wi-Fi.
- Tested every song in the album, and they all played flawlessly.
*PART 2 - USB 2.0*
- Now, I erased the Coldplay album from my iPod Touch.
- Connected my iPod Touch to my computer, and downloaded the album again via iTunes. I copied the very same album to my iPod Touch, this time using the USB 2.0 connection.
- I tested every song in the album. Guess what: most of them are corrupted, skipping, glitching, making garbled noises.
I think a reached a minor "eureka" moment. *It's not the iPod Touch software: It's iTunes, and how iTunes deals with your USB 2.0 connection*.
Now, I'm not an engineer, and I don't know how to fix this problem. I wonder if there's anyone out there there that knows why high bitrate files get corrupted during the file transfer. Hope anyone can shed some additional light on this issue, so we can find a solution.

HT4628 I am no longer able to iTunes wi-fi sync since I upgraded to the iPhone 5. Can anyone help me with this issue? Your help would be greatly appreciated.

I am no longer able to iTunes wi-fi sync since I upgraded to the iPhone 5. When trying to connect, it stays in the discovery mode and never connects.I have to try and pair them all over again. Then I get a message saying that my Mac Book Pro is not supported. Can anyone assist me in resolving this issue. It is an early Mac Book Pro 10 I believe. I purchased it in February of 2010.

I just figured out the print quality issue for my wife with her new iMac and new printer.
She replaced both at once and she couldn't understand why her Artisan 730 was lower quality then her Epson R280 when they had the same specs.
Turns out the newer printer had the option to connect via wifi which we used during setup.
The driver options are completely different depending on how you connect.
Once I connected via USB the correct options were available and the print quality was better.
Looking at the R2400 it dies not have wifi, but while researching the problem for my wife someone esle was having an issue updating to the latest printer driver.
If you go into the print utility from the Printer and Scanner system preference and under the general tab you should have driver 5.5.
One user had to delete the old printer driver before Software Update loaded the newer printer driver.
https://discussions.apple.com/message/15947486#15947486
On my MacBook Pro (w Snow Leopard) I always had to reconnect my wifi at home when it woke up. I upgraded my router from an old Netgear to a newer N D-Link and stopped having to do that.
I would be surprised you would have that problem with an Airport Extreme, you might check to see if there is a firmware update for it.

Firmware upgrade, then lost

Hi,
Quickly following automatic firmware upgrade on 1 week old Time capsule, network is now lost. Airport set up utility can't find Time Machine .. others experience the same problem? TM feels hot .. perhaps overheated due to firmware upgrade. Solutions welcome.

Your computer came with OS 9.0.4 installed. OS9.1 is required for Classic so is handy to have, and apparently your firmware installer requires 9.2.1 You can use free updaters to update to any later OS9 version from any earlier one.
I don't see any option but to obtain a used copy of OS9. Make sure you get the gold full retail version rather than a machine specific version since the latter will only work in those computers for which they were designed. You can get away with a machine specific version as long as it exactly corresponds to the model and build of yours, but that is often hard to confirm until too late in the purchase.
Note that any drive you want to use with OS9 either for purposes of installing OS9 or for running software will have to have OS9 drivers present on it. These are installed when you format a drive and cannot be installed later without reformatting the drive (and losing everything on it). If your computer still has its original drive then those will likely still be on there unless you reformatted the drive with OSX and did not select the keep OS9 drivers option (there's no harm in doing so and it saves a lot of trouble for doing exactly what you are trying to do). You can can have a drive present that doesn't have the drivers but it simply won't be seen by OS9.
Disconnect all third party hardware (including PCI cards) when updating the firmware.
Message was edited by: Limnos

RVS4000 since firmware upgrade no IAC

Similar Messages

Maybe you are looking for