RVS4000 WAN VLAN tagging.

I have upgraded this device to Firmware Version: V2.0.2.7 (yes its a v2)
As far as I can see it is missing a critical function; I can not put a tagged VLAN on the wan interface. I intended to use this in router mode with a static wan and all firewalling disabled as my CPE equipment on a 100mbit metro-e.
The provider requires the traffic be tagged on the CPE side. I did not want to use a low end dd-wrt device (who's gui only supports upto vlan 15 but you can define higher by hand) as it is not "standard" and supported. I like to provide clean solutions that can be maintained by persons other then myself if needed.
Is there any way to access the CLI on these small business routers and accomplish this by hand?
Thank you.
Don

As you can read above, I'm having problems with my IPTV pixelation/cuts... I need to be able to connect directly to the fiber and have more control over the connection, but I don't see the option on the web admin for PPPOE over VLAN. I don't know if it's a hardware limitation or just software (the GUI).

Similar Messages

  • RV320 and WAN VLAN tagging/IPTV

    I have a fiber connection on WAN1 which only works with VLAN tagging and I can't find a way to make it work without the provider's middleware router (Comtrend C5813)... Is there a way to connect to my FTTH (Lucent I240G-B) router directly? I'm having problems with my IPTV (multicast) service, if it's connect direct to the middleware I can have multiple channels running at once, but if I go back to the RV320 and do the same, everything start to pixelate.
    Using Wireshark I can see that the RV320 is connecting to the different channels with CS4 DSCP marking.
    Any ideas?
    Thank you!

    As you can read above, I'm having problems with my IPTV pixelation/cuts... I need to be able to connect directly to the fiber and have more control over the connection, but I don't see the option on the web admin for PPPOE over VLAN. I don't know if it's a hardware limitation or just software (the GUI).

  • Transport dot1q vlan tagging over wan link

    Hi,
    I would like to transport 802.1Q vlan tagging over a wan link, is it possible ?
    I heard about l2tp V3...
    Best regards

    Hi,
    You would have to use a technology such as Ethernet over MPLS (EoMPLS) or VPLS. This technology is referred to as Layer 2 VPNs. You can get more info on this at the following locations:
    EoMPLS (part of the Cisco Any Transport over ATM suite):
    http://www.cisco.com/en/US/products/ps6646/products_ios_protocol_option_home.html
    VPLS:
    http://www.cisco.com/en/US/products/ps6648/products_ios_protocol_option_home.html
    Hope that helps - pls rate the post if it does.
    Regards,
    Paresh

  • Cisco RV180 VLAN tagging WAN interface

    Is there by any chance in the future firmware update that this product (RV180) will be able to support VLAN tagging on WAN interface like the Cisco's RV315W router? ISP in Singapore (Singtel) and Malaysia(Unifi) (http://klseet.com/index.php/mikrotik/mikrotik-rb750-750g/setup-for-unifi) requires certain type of vlan tagging on the WAN interface for it to work. 
    Is there any workaround to this?

    I tried with only two vlans and set the DHCP active only for the office "vlan2". Computers receive the correct ip but some of them won't register on the network, i tried to set the ip manualy on the computers but that computer will still be isolated.
    Ex: computer A receives ip 192.168.10.25, Subnet 255.255.255.0, Gateway 192.168.10.1, for 2-3 minutes i can access the router on 192.168.10.1 and the internet, after a random time interval the gateway won't even respond to ping.It's not from firewall related issues as i set to accept all both incoming and outgoing. If i set a manual ip corresponding to vlan1 "default" everything works.It's like that computer is isolated so i believe it has to do with the asignment of Tagged, untagged and Excluded settings on the vlans.

  • 802.1Q VLAN Tagging on DSL WAN Connection

    Hi
    Does anybody know if SRP527W supports 802.1Q VLAN tagging on DSL WAN connection for RFC1483 bridged connections?
    Thanks
    Justin

    Hi Justin,
    Sorry for the delay in responding.  Yes, this feature is now supported by the SRP527W using the MR3 release.  (Please see https://supportforums.cisco.com/docs/DOC-13853).
    Andy

  • RV Support VLAN Tagging on WAN Port?

    Hi,
    I'd like to know if RV Series Router can support VLAN tagging on the WAN port itself? I need this cause my ISP using such method to connect to end user modem/router.
    Thank you.
    Regards,
    Danny

    Anything available other than this RV315W?  That model is only 10/100 on the LAN.  VLAN on the WAN is fairly standard for fibre installs and should be a feature across all SMB routers.

  • ISA550, ISP VLAN tagging?

    Hi,
    Just purchased an ISA550 to replace the ISP's router. I've been told that they use VLAN 101 for internet traffic. My public IP address is allocated from ISP's DHCP server.
    So I need to configure WAN1 for VLAN 101, but since I don't have the IP address/subnet how do I configure the IP setting for WAN/VLAN 101?

    Hi Wei,
    That requires username/password, which isn't needed. It's a regular Ethernet WAN connection with VLAN tagging. The ISP provides triple-play this way. Their Sagem routers supports it out-of-the-box

  • Vlan tag issue with Nexus 4001 in IBM Blade Centre

    Hi
    I have a DC architecture with a pair of Nexus 7010's running 3 VDC's (Core/Aggregation/Enterprise). I have at the edge Nexus 5548's which connect to back to the Aggregation VDC. Also connecting back to the Aggregation VDC is an IBM Blade Chassis which has a Nexus 4001i in slots 7 and slot 9. These blade servers are running ESXi 4.0 and are mapped to the Nexus 4001 blade switch.
    I had set up the Native VLAN as VLAN 999 which connects up to the ESXi host and I am trunking up multiple VLANS for the Virtual Machines.
    The problem I have is that VM's in all VLANS except the ESXi host VLAN (VLAN 10) cannot see their default gateway, and I suspect that there is an issue with the VLAN tag going up to the ESXi host. I have read enough documentation to suggest that this is where the issue is.
    My Nexus 4001 interface configuration is below
    interface Ethernet1/1
      switchport mode trunk
      switchport trunk native vlan 999
      switchport trunk allowed vlan 10,30,40-41,60-62,90,96,999
      spanning-tree port type edge trunk
      speed auto
    The Aggregation VDC on the Nexus 7010 is the default gateway for all these VLANS.
    I also noted that the Nexus 5000 and Nexus 7000 supports the command vlan dot1q tag native command yet the Nexus 4000 doesn't seem to support this. Any assistance would be useful
    Thanks
    Greg

    Your configuration on the N4K looks correct. You shouldn't use vlan dot1q tag native commands on your N7Ks and N5Ks. Native VLAN tagging is really for QinQ (dot1q tunneling).
    My only suggestion is check your configuration of the vSwitch in the ESXi host and the host network profile.
    Regards,
    jerry

  • Mesh Ethernet Bridging with VLAN Tagging Issue

    Hi all.
    I'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again.
    Has anyone else seen this? I can't find any relevant bugs.
    Justin

    Hi Saravanan,
    It is one RAP and three MAPs. After a TAC call and 30 hours of monitoring, my VLANs have remained registered. I think the issue was mismatched VLANs to bridge groups an it looks like the mesh bridge may be stable for now. Here is what I was seeing on the RAP and MAPs when the VLANs were deregistering unexpectedly. Notice how VLANs 2 and 10 are mapped to opposite bridge groups on the RAP and MAP:
    After I removed all the VLAN IDs from the Trunk configuration on the MAPs (through each AP's Mesh tab -- Ethernet Bridging config) and then rebuilt the VLAN IDs, I ran the same commands and now see this:
    My very unscientific theory here is that the mismatching was causing consistency checks to fail, so the RAP was just tearing down the registrations after getting bogus or non- responses from the MAPs during the periodic VLAN registration maintenance checks (debug mesh ethernet registration).
    If I have continued issues, I'll post back with updates.
    Thanks for the response!
    Justin

  • 7600 second-dot1q & vlan tag manipulation

    Hi,
    Does anyone know what the hardware requirements are for using config such as "sencapsulation dot1Q 660 second-dot1q 1" or any of the "service instance" commands such as below to manipulate dot1q tags?
    Im running 7600 with SIP-400, IOS 12.2(33)SRD and there are no such commands available at the cli. Suspect ES-20 is needed as a minimum but can't see this mentioned in any docs.
    interface FastEthernet1/0.660
    encapsulation dot1Q 660 second-dot1q 1
    OR
    interface GigabitEthernet3/0/0
    description Sample Configs
    service instance 1 ethernet
    encapsulation untagged
    rewrite ingress tag push dot1q 3 symmetric
    xconnect 10.30.30.173 2 encapsulation mpls
    service instance 10 ethernet
    encapsulation dot1q 10
    rewrite ingress tag pop 1 symmetric
    bridge-domain 500 split-horizon
    service instance 20 ethernet
    encapsulation dot1q 20 second-dot1q 200
    rewrite ingress tag pop 1 symmetric
    bridge-domain 500 split-horizon
    service instance 30 ethernet
    encapsulation dot1q 20 second-dot1q any
    rewrite ingress tag pop 1 symmetric
    bridge-domain 500 split-horizon
    I just need to pop the service vlan tag. At the moment I'm using a port per service to peel off the outer tag and this approach isn't going to scale.
    Appreciate any advice on this.
    Cheers
    Kent.

    Hi Jerry,
    I believe - about to test it - that this only works with SPA-v2 interfaces. I was testing with a SPA-v1 interface previously. Is this your understanding? Docs are pretty light on with hardware requirements.
    Show ver:
    Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVIPSERVICES-M), Version 12.2(33)SRD, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Thu 23-Oct-08 22:32 by prod_rel_team
    ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)
    pe1.lab uptime is 19 hours, 5 minutes
    Uptime for this control processor is 19 hours, 5 minutes
    System returned to ROM by power-on (SP by power-on)
    System restarted at 17:09:22 EST Mon Jul 27 2009
    System image file is "bootdisk:c7600s3223-advipservices-mz.122-33.SRD.bin"
    Last reload type: Normal Reload
    cisco CISCO7606-S (R7000) processor (revision 1.0) with 458752K/65536K bytes of memory.
    Processor board ID FOX11310AY3
    R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache
    Last reset from power-on
    1 SIP-400 controller (4 GigabitEthernet).
    10 Virtual Ethernet interfaces
    125 Gigabit Ethernet interfaces
    1915K bytes of non-volatile configuration memory.
    65536K bytes of Flash internal SIMM (Sector size 512K).
    Configuration register is 0x2102
    Modules are now:
    7600-SIP-400 and SPA-2X1GE-V2

  • Does Cisco7200VXR support feature Q-in-Q VLAN tag termination?

    There is only 10000ESR platform support announced in feature guide and no information in Feature Navigator tool...
    http://www.cisco.com/en/US/customer/products/sw/iosswrel/ps5207/products_feature_guide09186a00801f0f4a.html

    Hi there,
    Well.. it seems this feature has several names:
    "Cisco IOS Software Releases 12.3 T - IEEE 802.1Q-in-Q VLAN Tag Termination"
    http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_feature_guide09186a00801f0f4a.html
    "Cisco IOS Software Releases 12.0 S - Stacked VLAN Processing"
    http://www.cisco.com/en/US/products/sw/iosswrel/ps1829/products_feature_guide09186a008021b9ee.html
    But I can't find any reference to the 7200 having support for it... though many others has it.. mainly switches.. not too surprising.. :)
    Did it help?

  • Vlan tag preservation span monitoring

    Hi
    I am spanning multiple vlans as source with the destination as a single ethernet port, though I am able to see the traffic from the VLANs, I am not able to see the VLAN tag in the packet which is a key requirement for me for monitoring.
    Does anyone know why the VLAN tagging is stripped or how to preserve it in the monitor session?
    Your help is much appreciated.
    - Balaji

    While I appreciate your response Najaf, we have been monitoring the SVIs on our current CAT6500 switches without any problems as we can "preserve" the vlan tags on the destination monitoring port.
    However, we have found a way to see the VLAN tags on the monitoring destination port but we are still carrying out some tests to confirm our findings.
    Will keep this thread updated.
    -Balaji

  • Installing OVM X86 3.1.1 with Trunk VLAN tag for ovm management network

    Hi Guys
    Can anyone help with network config on the OVM server 3.1.1 basically we need to use vlan tags on trunk port... so i have a subnet from following *(Trunk Allowed VLAN XXX)* from which i need to allocate IP for the OVM server component so that the ovm manager can find the OVM server instance...
    Can you use vlan tags, on trunk port with OVM server 3.1.1???
    Thanks

    Your right there as i later found out the engineers weren't selecting the vlan option when installing the vm server...

  • How to get vlan tag programe with mac book air

    how to get vlan tag programe with mac book air,i'm using the usb ethernet adapter

    For prompt help contact TATA.
    For more on this: https://discussions.apple.com/thread/3680625?tstart=270

  • VLAN tagging for Desktops

    I have a test VDI 3.1.1 system set up and I have to say, I'm quite impressed. In about a day, I was able to serve Windows 7 desktops, something we can't do with our current VMware View setup. One apparent limitation I have run into, however, is 802.1q VLAN tagging support for Desktop NICs. I have created a 2-way aggregate on nxge0 and nxge1. The portchannel these are connected to is set up for 802.1q tagging, and Solaris is plumbed with aggr13001 to tag its packets with VLAN 13, for example. However, traffic from Desktops is not so tagged, so its packets go nowhere. Is there any way to define a VLAN for a given Desktop Pool? This is important for us, as we tend to keep server systems on campus-only subnets, while desktops get Internet-routed addresses.
    Thanks,
    Charles

    Aggregation shouldn't have any adverse effect here. You need to configure VDI to use the correct VLANs on a per Pools basis. In the VDI Manager first navigate to the Desktop Provider -> Networks tab and 'Refresh' the networks. This will scan all VirtualBox hosts in the provider for currently plumbed interfaces, each of which will be listed by their subnet.
    After all networks are detected navigate to the Pool -> Settings tab and select 'Host Networking' followed by the required subnet(s). The primary subnet listed here is used for RDP connections.

Maybe you are looking for