RX9800pro-TD128(red board) meny problems

Hello everyone..
I bought a ATI Radeon rx9800pro td128...
got some major problems in games...like tearing ..blicks..some textures moveing out of walls in sharp format..and those kind of stuff...
i saw all otehr posts i tryed all but it doesnt work even wount hlp a bit..that made me think card is damaged...
as tryed all i mean : - giving more power to card like taking out of floopy drive power plug...and as usuall in meny forums of ati i tryed uninstaling drivers of old card (GeForcemx4) then unistaling ati drivers again,reboot install ati again...i even formated win xp service pack 2 and instali it fresh and all fresh new drivers again but its the same...i tryed with catalyst tool ..no hlp with it...i updated all new drivers for mainboard (nvidia nForce2...wich i think is the problem)...i tryed omega drivers too... i tryed turning off fast writes on agp settings in bios and catalyst tool...i think i did everything and there is no hlp...so i am really close to grab it out and smash it at the wall!!
i got issues in every game like ...CoD, Mohpa , CS , World of Warcraft and more...
but i only got problems in games nowhere else..
Anyone got same problems ?
Someone know answers to this problems ?
If u got an idea just answer ill try it as i tryed all...
Thx for reading this post..i hope You all will resolve this problem..
my conf...
Winxp SP2
Nvidia Nforce2
AMD Athlon(tm) Xp 2200+
1.80 Ghz
768 MB DDR of ram
ATI Radeon RX9800PRO-td128

yes Mechwookie you are right ...sorry mi mistake ..i am a newbie to those kind of things when we are talking about chips on boards...
you have to tell me more and explain how to check wot u need exactly?
Dr Stu : ...well, all we know then is this is some SocketA board with nforce2 chipset, that doesn't have a 4pin 12v connector...
yes that is true SocketA board with nforce 2 mcp..meny other connectors but not 4 pin ones...
btw from motherboard info from 3dmark03
Manufacturer
Model nVidia-nForce
Version
BIOS Vendor Phoenix Technologies, LTD
BIOS Version 6.00 PG
BIOS Release Date 03/24/2003
BIOS Properties Plug and Play, Flash, AGP
AGP
Revision 3.0
Rate 4x, 8x (8x enabled)
Available Rate 0x0000000c
Selected Rate 0x00000008
Aperture Size 0 B
Sideband Addressing supported (enabled)
Fast Write supported (disabled) - disabled becouse that was one of "problems" becosue of issues in games
and CPU info also from 3dmark03
AMD Athlon(tm) XP 2200+ 1.8 GHz
Manufacturer AMD
Family AMD Athlon(tm) XP 2200+
Internal Clock 1.8 GHz
Internal Clock Maximum 1.8 GHz
External Clock 133.0 MHz
Socket Designation Socket A
Upgrade ZIF Socket
HyperThreadingTechnology N/A
Capabilities MMX, CMov, RDTSC, 3DNow!, Extended 3DNow!, SSE
Version AMD Athlon(tm) XP 2200+
Caches
Level 1 128 KB
Level 2 256 KB

Similar Messages

Big MSI RX9800Pro-TD128 problem

Hi everyone!
I am a proud owner of a Radeon 9800Pro (MSI RX9800Pro-TD128) and I've got an issue that looks very much (or exactly) like this:
http://img.photobucket.com/albums/v302/IvanV/shot0000.jpg
If you failed do recognize it, this is a screenshot from 3DMark03 GT4. It happens with all driver versions I tried (from MSI and from ATI). It used to happen only in GT4, so I wasn't to concerned, but now it also happens in HL2 when AA and AF are turned on (which is also strange, because I didn't use 3D Mark with AA and AF). The card is not overheating and works fine in other situations. My system:
CPU: AMD Athlon64 3000+
MB: MSI K8T Neo (VIA K8T800 chipset)
RAM: 512MB DDR 400MHz Kingston ValueRAM etc...
Windows 2000 Professional with SP4, DX 9.0c

Today, after months of having this issue, I solved the problem. Still, I don't understand why this worked, so please someone explain it to me. I found two solutions:
1) Change AGP aperture size to 256MB. Since I have only 512MB of RAM, things got a bit less smooth, so I was thinking, since things did work from time to time, and guided partly by memory and partly by instinct I
2) returned AGP aperture size to 128MB, and removed desktop wallpaper, screensaver, custom Windows appereance in Display Properties and it also worked.
I retested all variations several times to make sure, and right now I have little doubt that this is a permanent solution. I only don't know why, so if anyone could tell me, I'd really appreciate it.

New cooler for RX9800Pro-TD128

Hi there, I've got a RX9800Pro-TD128, it's a great card but the cooler is quite noisy, so I'm considering buying a new VGA cooler, and since the card has a differente PCB I'm wondering which coolers will fit?
VGA Silencer Rev. 3
VGA Silencer 1 (for Radeon 9800 Pro)
VGA Silencer 3 (for 9800 Pro with 256MB and XT)
Coolermaster CoolViva
Aerocool VM-101
Thermaltake GIANT II
[/list]
Thanks

i have a rx9800 pro and a vga silencer rev3 mounted on it. its pretty simple to do and no effort really. you take the 2 pin connector off the vga silencer. take a small needle or knife point and use tha to open the claps on the side of the white connector to remove the wires and do the same with the connector attached to the stock cooling fan, and just swipe connectors and put the stock one on the vga silencer and connect it to the board. and boom it will work, just remember where the origonal wires go on the stock connector i belive the red goes towards the inside of the card and black towards the outside i think, double check tho. I did it with no problem and in less then 5 min.

RX9800PRO-TD128 Artifacting

Hi, I just bought my RX9800PRO-TD128, installed it and ran 3dmark03. The first tests ran fine but Nature bought on extreme artifacting. I mean you cant see anything familiar just random colored pixels all across the screen. I then quit 3dmark and windows was also displaying in a very distorted way. After a restart it was ok again (not nature)
I formatted and reinstalled my system but the problem still exists.
I dont overclock so it cant be that.
Any help will be apreciated

Hi
My first Post
I have just bought my Msi RX9800PRO-TD128.
Not sure I have done the right thing, have always used the well tested Nvidia card.
I was talked into buying one.
Thought I would do a complete install to eliminate any reg errors, to my amazement all went well without any known issues.
Used the drivers supplied with the card.
Don't seem to be any heat problems so far
Still a bit unsure yet, lack of confidence in ATS cards.
Case Lian Li PC60
Power supply Enermax EG465P-VE 431W
Processor Intel 2.53 GHz Retail
Motherboard Gigabyte GA-8PE667-Ultra
Ram 1 gig Samsung PC2700
Graphics MSI AGP Radeon RX9800 Pro TD128MB
Hard Drive Seagate 80Gig Seagate 40 gig
Sound Card SoundBlaster 5.1 Live With Surround Sound
CD/ROM LG 52x IDE
CD/Writer Liteon 24x10x40
Monitor Acer TFT AL1731
OS Windows XP Home Edition/

[RX9800PRO-TD128] What is new in the "version 2" of this card?

I will buy these card (i live in Spain), but in the store (http://www.alternate.es) appears a new version of this card ("version 2") that is cheaper.
What´s the difference between the old and the new versions?
Thank You!

See it by yourself:
http://www.alternate.es -> Hardware (in the left side) -> Gráficas -> Tarjetas gráficas AGP -> ATI.
And then you will see two graphic cards:
RX9800Pro-TD128
(salida de TV, DVI, Retail) 229€
(Tech. info here: http://www3.alternate.es/cgi-bin/info/showtechdata.pl?artnr=j9gn52 )
RX9800Pro-TD128
(TV-Out, DVI, Version 2, Retail) 214€
(Tech info here: http://www3.alternate.es/cgi-bin/info/showtechdata.pl?artnr=j9gn54 )
It´s posible that this last card will haves a 128bit memories, but if somebody knows this thing sure...
Thanks for your help

Rx9800pro-td128 vs rx9800pro-td128sp

I ordered a "rx9800pro-td128" from newegg. what arrived is a "rx9800pro-td128sp".
The "sp" version is listed as "new" on msi's site, but it looks to have a smaller heatsink/fan. why is this the "new" version? is the sp version "newer and better for the end user" or "newer and better for msi to sell" (ie. cheaper to make)?
Normally I would specifically want a "new" model, but the heat sink on the "old" version looks like it would do a better job. I did read in one post that the fan on the "old" model was noisy. Is the fan on the "new" model less noisy? Has anyone done any temp comparisons to know if one is better than the other?
Also, can anyone please summarize what the r350 and r360 core differences are? Why does everyone want the r360?
Any help or advice would be appreciated.
- J

As far as I know, Ati`s card don`t come with any games at all.
Some other companies include some games but not too many.
MSI is the company that give you the most games.
If all the 14 in 1 games are all full versions, it is an excellent bundle of games.

RX9800PRO-TD128SP and RX9800PRO-TD128

RX9800PRO-TD128SP vs RX9800PRO-TD128
so what is different.
i can see new PCboard, new fan.
same mem?
same core (the 360)?
the websites don't say anything about what was changed
any help will be great

I have the original rx9800pro and it is recognized as the 9800xt with ati drivers, and shows an r360 core everywhere i look. Wiith its awesome cooling, i can get it to 445core, and 385memory stable. It is as good as the Artic cooling solution easily. I never run it at that though, because im not big on overclocking. Anyways I do set it at a more conservative 410core and 360memory and i score 6800 in 3dmark 2003 and 47,000 in Auquamark. I use the ATI drivers v4.8, not the msi drivers. I am sure glad i got an original before they switched to the newer design. Does the newer design use the same cooling, for your sake i hope so. For $189 retail, it was a steal. I love it.

IPhone will not ring if locked even when Do Not Disturb is not on. Even when the sound toggle on the side is not red. This problem occurs regardless of whether it I have Do not Disturb on (manually, or scheduled) or COMPLETELY OFF.

iPhone will not ring if locked when when Do Not Disturb is not on and the phone is not on silent (button on side is not red). This problem occurs regardless of whether it I have Do not Disturb on (manually, or scheduled) or COMPLETELY OFF. I've tried wiping the phone and reinstalling from a saved copy but of course the problem comes back because the problem is inherent in the save. There are two options under "Silence" at the bottom of the Do Not Disturb preferences. "Always" or "Only when iPhone is locked". Those are the only two options and I want neither. No amount of deselecting will work. It forces you to pick one.
Does anyone have a solution given that I've better explained the problem?

The settings at the bottom of the Do Not Disturb page do not matter if you have the switch for Manual turned to off, or the Scheduled turned to off.
When the phone is unlocked, if you try to raise the volume of the ringer, what do you see on the screen? Does it say ringer, do you see the word headphones anywhere?

Solaris 8 on Intel STL2 server board - installation problem

Hi,
I try to install Solaris 8 (4/01) on Intel STL2 server board (P III 866 MHz, SDRAM 512 ECC Reg, Adaptec AIC7899 Dual Channel-one Ultra160/LVD channel, Intel PRO/100+ Fast Ethernet Controller, ATI Rage* IIC SVGA) - without success.
It recognizes all devices but after I choose Solaris Interactive installation (from CD labeled Solaris 8 Software 1 of 2 Intel Platform Edition) it displays:
Booting kernel/unix...
SunOS Release 5.8 Version...
then reboots after 2 seconds.
Since Intel STL2 board appears in the HCL for Solaris 8 I have struggled a while with the problem. I have not found neither post nor driver update information concerning this issue on the Solaris' related Web sites.
Finally, I found the very strange specification update info of STL2 board, published by Intel:
"13. Sun* Solaris* 8 installation issues
PROBLEM: Sun Solaris 8 cannot be installed on the STL2 server board with any BIOS version later than BIOS Release 1.1, Build 15. The system reboots during install and therefore the installation cannot be completed.
IMPLICATION: Installation of Sun Solaris 8 cannot be completed on an STL2 server board running any BIOS release later than BIOS Release 1.1, Build 15.
WORKAROUND: Sun Solaris* 8 will successfully install on the STL2 server board with BIOS Release 1.1, Build 15."
My BIOS release on the STL2 board is 1.7. It's too new to install Solaris 8 !?!
I am unable to get an old STL2 model with BIOS 1.1. Is there a way to update anything in the Solaris 8 in order to set it up on the new model of Intel STL2 server platform?
I would appreciate any help. Thanks.
Matt

The problem has been resolved.
I got the older BIOS 1.1 Build 15 for Intel STL2 from Intel Internet Support. After I installed BIOS 1.1 instead of BIOS 1.7 had no problem with installation of Solaris 8.
Matt

Red eye editing problem

Hi all, I am new here and this has probably been asked and answered but I have not been able to find the answer yet, so please don't slam me to hard for asking for help. The problem I am having is with photos that have red eye in the original. I can edit the red eyes out and the photos look fine on my new imac but when I e-mail to friends they can't believe that the photos I send them have big black eyes. I am guessing it is something to do with the red eye editing. Am I doing something wrong or do I need to use a different program for red eye edits on photos that I send to others, particularly Windows users?
Thanks so much in advance for any help.
Jim Morris

turtle21:
Log into another account on your MBP and see if the problem persists when using iPhoto there. If it does then it's system wide. If the problem is gone then you've narrowed it down to your account.
If it's system wide the 10.4.0 COMBO updater that TD suggested would be the first thing to try. Next to that would be as reinstall of iPhoto. If or when you do try a reinstall of iPhoto you'll have to delete the current application and all files with "iPhoto" in the file name that reside in the HD/Library/Receipts folder. The reapply the updaters in the following order: 6.0.4, 6.0.5 and 6.0.6. The last two require the previous version to run.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

Red Close Button Problem

Hi there,
After i have installed the mavericks update for my macbook pro, i had started having a problem in closing my apps or browser or files with the red X button,
When i click on the button to close my apps it doesnt work at all unless i drag the app or browsers a little bit and then close them. This is annoying, So if someone can help me fix this bug or something.

A Safe Mode boot deletes some system caches that may help.
Startup your Mac in Safe Mode
A Safe Mode boot takes much longer than a normal boot so be patient.
Once you are in Safe Mode, click Restart from the Apple () menu.
Then try the red button.

Community boards notification problem.

Didn't quite know where to post this, hope here is okay!
Although I have all the various options for notifications by email selected in the board preferences, I am not getting any sent through, the email address is correct. Any one else having this problem and/or know how to rectify the problem?
Cheers.

Thank you, Andrew.
I have reported the matter to the hosts. As you will understand, they operate in their own way and we cannot guarantee they will reply. But my experience is they are very helpful and usually resolve matters like this.

Red-eye reduction problem

When I use the red eye reduction feature, suddenly it is putting the "fix" on the photo, not on the eye where I click to remove it. Is this a problem anyone else has had and can it fixed? I use iphoto 6.0.4.
Thanks,
Ardelle

Ardelle,
There is a hidden feature that allows you to resize and place the red-eye tool. It works with the Retouch tool, as well.
Type Caps lockControl9
Undo caps lock
Click on Retouch or the Red-Eye Removal tool.
The tab key will toggle between cursor types: a cross or a circle for Red-Eye removal tool, and between darken and lighten in the Retouch tool.
The \[ and \] keys decrease or increase the size accordingly.
NOTE: Using the { and } keys will will change the value next to the circle and that represents the degree of change or intensity that the Retouch tool imparts on each pass. To get a lighter pupil with the red-eye tool, Shift-Click inside the circular cursor.
Thanks to Old Toad for posting that tip.
Regards.

Board Game problem

Hi!
Im creating a board game and I'm having a problem. The aim of the game is to eliminate the opponent's pieces. Each time a player gets a three in a row of pieces, they are allowed to remove any one of the opponent's pieces.
My problem is this: If a player gets a three in a row, in his next two moves I want to disallow him moving one piece out of this three in a row and then back into it so as to try and remove another of the opponent's pieces with the same three in a row.
Here is the Player Class
public class Player
     char piece;
     String name;
     int numberofPieces;
     Player(char pieceVal, String name){
               this.piece=pieceVal;
               this.name=name;
               numberofPieces = 5;
}So when a player gets three in a row, I want to record his 3 in a row, and watch his next two steps and prevent him from having the same 3 in a row after 2 steps.
Can anyone help me? It has been wrecking my head for 2 days now!!
Thank you.

How about keeping a turn counter as well as the coordinates of the pieces in the player's last 3 in a row?

APEX 4: Theme "Simple Red": "No Label" Problem

Hi,
we developed an application in APEX 3 which we currently update and roll out APEX 4.
Everything works great so far but we have a problem with the new theme we switched to in the app.
We decided to use "Simple Red" in the next version of the application.
The main problem with this is that the element labels are shown although the template "No Label" is selected.
Of course it is possible to change the label from "Whatever" to " " to workaround this bug.
But because there are many of the labels which shouldn't be shown it would be better to make "No Label" work as aspected.
Does anyhave have the same problem? How can we resolve that issue?
Thanks
Regards
Daniel

I found the solution!
Go in to the template "No Label" and replace the entry on "Before Label" to "<span style="display:none;">" and "After Label" to "</span>".

RX9800pro-TD128(red board) meny problems

Similar Messages

Maybe you are looking for