S-ATA RAID-1 okay but no other IDE devices?

Had 865 FIS2R running just fine with 3.2 G P4, 512 MB Cosair, ATA-100 IDE disks and an H-P 300i burner.  Wanted to move up to S-ATA and purchased 2 of the Seagate 160 Gig S-ATA drives.  Bios was flashed to 1.4 and ran fine until . . .
Just flashed to 1.8 on my 865 FIS2R and installed 2 Seagate 160 Mb S-ATA HDDs and have them "Functional" on the Promise S-ATA controller.  Next step is to install WinXp(Pro), but system does not detect CD-ROM on IDE-1 or IDE-2 jumpered as Master, Slave, Single, etc.  Trying another CD-ROM does not change symptoms.
When booting, no IDE devices are detected, but the S-ATA drives come on line okay (using Win98 boot disk).  Win98 Boot Disk cannot detect CD-ROM drive, either.
Tried changing IDE detect from Auto to CD-ROM on both Primary and Secondary IDE channels.  Still no CD-ROM detected.
Read manuals and cannot see what is not set right to get IDE devices detected during boot up.
Where to look for what, next, please ?

Did you try going into the BIOS and on (Integrated Peripherals) page go to On-Chip IDE Config. And make sure that you have it set to Both S-ATA+P-ATA Enabled? and Both IDE channels Enabled? I say this because it happened to me an sure enough it was somehow set to S-ATA only...And I only had the Primary IDE channel enabled (and I was SURE I did not set it that way)...Sean REILLY875

Similar Messages

  • Why is my Wifi dropping on iMac but not other Apple devices?

    I am trying to figure out why my iMac constantly drops the Wifi connection.  My router is new and only a couple feet from my iMac.  My husband's macbook pro does not drop the Wifi connection.  Usually, the Wifi connection is lost for a matter of seconds or minutes and reconnects without me doing anything.  My Wifi works at lightning speed when it is connected but drops off several times a day and sometimes multiple times an hour.  This is so frustrating! 

    WiFi Problems:
    Wifi problems seem to crop up a lot on here and unfortunately there doesn't seem to be a 'one fix' solution.
    However, sometimes any one of the following can help although, unfortunately, not always. In no particular order:
    Check wifi security - if it's WEP change it to WPA or WPA2 (preferably, as it's more secure)
    Change the wifi channel on the router
    Create a new Network Location: http://support.apple.com/kb/HT5289
    Reboot the router
    Also take a look at this link and the links within the article for other ideas. They mainly reference Lion, but still seem to be relevant to Mountain Lion and possibly Mavericks:
    http://osxdaily.com/2011/11/06/lion-wi-fi-problems-solution-mac/?utm_source=feed burner&utm_medium=feed&utm_campaign=Feed%3A+osxdaily+%28OS+X+Daily%29&utm_conte n t=FaceBook
    ...and this link:
    http://osxdaily.com/2012/11/30/resolving-stubborn-wi-fi-connection-problems-in-m ac-os-x/

  • Apple TV keeps hanging with my MAC but not other Apple devices

    I also have a Time Capsule connected to my MAC and I think this is why it hangs.  My Iphone works without any issues.  My daughters and her friend's Macs' and Iphones work without any issues.  They are not connected to the Time Capsule.
    Are there any known conflicts between Apple TV and Time capsule ?  I have the latest firmware on my Time Capsule.  It is in (Off) Bridge mode.  Ip Address is 192.168.1.33
    Regards
    Brij

    Hello Brij,
    Thank you for providing all that information about what is going on.  I found an article that might help resolve the playback issues using Airplay mirroring:
    Troubleshooting AirPlay and AirPlay Mirroring
    http://support.apple.com/kb/ts4215
    I recommend taking a look at the section titled, "Troubleshooting performance issues with AirPlay or AirPlay Mirroring."  This article is for iOS devices as well as Mac computers, so you can skip any of the steps that refer to an iOS device.
    Thank you for posting in the Apple Support Communities!
    All the best,
    Sheila M.

  • More than 4 IDE devices using the Raid controller on the MSI-6567 645E Max2-LRU ?

    Here is the specs page of the board
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=79
    I have a HD and a CD-ROM drive on the first IDE controller, and an HD and a CD-writer on he second IDE controller
    Since the specs say the board only supports 4 IDE devices I was wondering-
    1) Can I connect another HD to one of the onboard Raid controllers, and work with it in addition to all the other IDE devices currently plugged in, without RAID?
    i.e. CD-writer, CD-ROM, and 3 HD's working together ?
    2) Can I connect 2 more HD's, one to each onboard RAID controller and have them work in raid in addition to all existing IDE deviced?
    i.e. CD-writer, CD-ROM, 2 HD's and 2 more HD's in RAID format working together ?
    Thanks in advance..  

    But like I said, I do not intend to connect CD-ROMS to the RAID controllers, only HD's - the CD-ROM and CD-Writer are currently connected to the normal IDE controllers and I don't plan on changing that in any case
    My question was whether or not i can add more HD's to my current system by adding them to the RAID IDE's
    simply put, to be 100% clear my question is this -
    will the current configuration work:
    IDE 1 = CD-ROM + HD1
    IDE2 = CD-WRITER + HD2
    RAID IDE1 = HD3
    and will this one work:
    IDE 1 = CD-ROM + HD1
    IDE2 = CD-WRITER + HD2
    RAID IDE1 = HD3
    RAID IDE2 = HD4
    when HD3&4 work in RAID mode
    Thanks again for you help
    RE your suggestion - why not put a CD-ROM and an HD on the same IDE ? that way my HD's are connected to different IDE controllers for better performance

  • I tried to reset my iphone5, the reset loading was okay, but after that there is other loading(the one that come everytime after shutting down), so its about 6-7 hours that my phone is stuck on this page. force shutdown didnt work.

    I tried to reset my iphone5, the reset loading was okay, but after that there is other loading(the one that come everytime after shutting down), so its about 6-7 hours that my phone is stuck on this page. force shutdown didnt work.

    There are many ways to do a reset on an iPhone so which one have you been trying that has got you to where you are now?

  • Silicon S-ATA raid message on boot?

    The Silicon S-ATA raid message on boot stays there for (what seems like) an enternity. Can I shorten the time the message is displayed (or go somewhere and disable it?). Thanks! [stats are in sig]

    Hi, Yes you can disable it in the bios.  Not sure what bois you are running but it is in there.
    Try entering cmos. 4th line down on the left.(advance chipset features)
    then the 3rd optioin. (Onboard device)
    At the botton of the list you will see onboard sil3132 raid disable enable.  Disable it. save and exit.
    Sorry for the line refference but I cannot remember what the line titles are called. (guessed at titles)
    Hope you find it ok.

  • Only one HDU on ctrl ATA RAID

    Hi!
    It is possible to use connector ATA RAID with a solo harddisk (in modality stipe)? Thanks.
    Federico

    it would be but its a bit pointless as it can only be slower
    http://www.msi.com.tw/program/service/forum/index.php?threadid=292&boardid=16&styleid=1

  • When I click on any of my movie or TV shows in Itunes I immediately get an error message that says Itunes has stopped working and closes the program. I can sync the movies and shows to my phone okay but I can't watch on Itunes. Can anyone help?

    When I click on any of my movie or TV shows in Itunes I immediately get an error message that says Itunes has stopped working and closes the program. I can sync the movies and shows to my phone okay but I can't watch on Itunes. Can anyone help?

    Let's try the following user tip with that one:
    iTunes for Windows 10.7.0.21: "iTunes has stopped working" error messages when playing videos, video podcasts, movies and TV shows

  • When i sign into icloud it says my apple id is okay but i do not have icloud and it will not prompt me to set it up

    when i sign into icloud it says my apple id is okay but i do not have icloud and it will not prompt me to set it up

    You can't setup an iCloud account using a PC. You need a Mac, or an IOS device. You can sign into iCloud on your PC once you open an account.

  • HT204150 iCloud and my iPhone sync okay but my second Mac does not sync with iCloud. What's wrong?

    iCloud and my iPhone sync okay but my second Mac does not sync with iCloud. What's wrong?

    Check your settings in System Preferences > iCloud

  • I would like to detect all the keyboard key is okay, but not every key can be detected by using LabVIEW example, keyboard keycode

    I would like to detect all the keyboard key is okay, but not every key can be detected by LabVIEW example ( we can use 『basic input demo.vi』to detect normal key』.
    I want to detect some 『hot key』 for example some keys exist in the upper part like 『search key』、『e-mail key』、『volumn control key』...etc. They are very often to be watched in some new keyboards, but we still don't know how to detect if their functions are okay.
    Can we detect signals of these 『hot key』 in LabVIEW? We can apply these hot key's functions in XP, so we should detect their signal, I think, but I can't do it.
    I serach some information about this question, and somebody said we can detect hot key's signal by grabing 『keybode』 these hot key feedback. But I don't know how to do these. I can't use VC. So anyone can give me a LabVIEW VI to grab keycode? Or any other solution we can detect all the key on the keyboard, including hot keys?
    Thanks!
    Regards,

    Maybe that is the limitation of Acquire Input Data.vi.The vi can't identify the Unformal key.
    You can try to use Event structure and set to listen "key down" event.
    There are two terminals VKey, ScanCode will sent out the information when you press key.
    There are two pictures in attached file, 2.jpg will show you the detail.
    Good luck.
    Attachments:
    SpecialKey.zip ‏17 KB

  • Digital audio input via mini jack/toslink from ADA, monitored via USB audio output... is this do-able? I know digital audio input should be okay but how do I monitor it, apart from using the internal speakers?

    Digital audio input via mini jack/toslink from ADA converter, monitored via USB audio output to amplifier... is this do-able? I know digital audio input should be okay but how do I monitor it, apart from using the internal speakers?

    You can output audio thru HDMI, with appropriate adapter.
    You can use additional cheap external usb audio for monitoring.

  • Internet connection okay, but safari doesn't work !

    Dear All,
    Internet connection okay, but safari doesn't work ! Version 6.0.2
    Appriciate your support

    hi there Michael
    sorry for the delay was on leave
    when i say download the software from the Apple's website i mean download the software update for mac os x 10.3.9
    as once you reinstall panther again it will revise back to the original version of the OS which came along with the computer when you purchased which will cause safari to be incompatible with
    so once you do a software update for you operating system it will get it compatible with safari
    so to get the update you can download it from the computer you have it burn the update on a CD or DVD and then install it on this computer
    you can get the download from
    http://www.apple.com/support/downloads/macosxcombinedupdate1039.html
    just click on the link above to get to the page then click on the number 117mb on the upper right hand corner
    once you have downloaded it burn it to a disc and install it on your computer
    hey sorry if i did not make myself clear earlier

  • Adding second s-ata raid 0 for windows fix!

    Hi , i need some help i have a problem on win xp prosp1 , it doesn´'t start because it missed or corrupted the windows\system32\config\system file....and i cant used the recupertaion console so ...i have a socond system with the same configurations
    and i want to rescue some file from hd so i don't know how i can add other raid 0 stripe to the other system whitouth eliminate the exist partition that was created on promise driver in the other system, once tipe i try to do this but in windows i didn't saw the hd, please can you help me on this?

    Moan Guide
    Start with this moan guide first. You'll know what we expect from you befor trying to help you out.
    So is hyour problem tryiing to get some data out of the RAID drive?
    Do you have extra hdd? If ye,s you can install a WinXP on this extra OS, and install the Promise driver. After that you should be able to see your RAID drive. Befor ethat, besure you go to BIOS and RAID BOS to check out you have everything set correctly.

  • There is a problem The new update is okay, but does not the name of appea in the AirPlay device is in sleep mode.

    There is a problem
    The new update is okay, but does not the name of appea in the AirPlay device is in sleep mode.

    Hi,
    Firstly, I would suggest we use Exchange 2013 FE as the Outlook Anywhere proxy server.
    For the certificate issue, it mostly occurs because the host name that Outlook are trying to access does not match the certificate SAN. Please check with this point. If they do not match, you
    can change the host name by referring to the following article:
    https://support.microsoft.com/kb/940726/en-us?wa=wsignin1.0
    Thanks,
    Simon Wu
    TechNet Community Support

Maybe you are looking for