S.M.A.R.T status failing on two internal hard drives at the same time.

Thanks for reading.
I have a Quicksilver, 733 mHz machine with 1g ram... the PROBLEM is that I have two identical 60 GB internal Maxtor HD's that have run wonderfully for many years... they just decided to tell Disk Utility that "this drive has reported a fatal hardware error to disk utility". And the S.M.A.R.T status is reported as failing- on BOTH drives. That is why I don't believe this... suffice to say, I backed up everything.
The only change that has occurred recently, is an upgrade to OS 10.4.10. In its current status, I cannont run first aid or reformat (which is what I was trying to do in the first place).
Any suggestions?

Alright, this thread is getting confusing! I am up and running again, though I am unable to start up at all on my main 17 inch apple studio display (old crt monitor). I switched to another old CRt (non-mac, and needs own external power) and it is starting up fine- faster than before actually. I went ahead and disconnected the disk without the operating system, and it didn't fix it, I then disconnected the disk with the operating system and this didn't fix it. I then reconnected both drives, took out the RAM and rebooted. Then shut down and restarted while clearing the PRAM. This didn't fix it. I then rebooted off of the restore/install disk and ran disk utility. It doesn't report any error messages and I am trying to run the repair. I will post the outcome.

Similar Messages

S.M.A.R.T. status: failed on recently replaced Hard Drive, ***?

S.M.A.R.T. status: failure on my Hard Drive,
does this mean my Hard Drive is going to fry once again? Not sure what this means.
Heres my story:
Bought a brand new 20" iMac with custom 500gb HDD in April 2007 ran like a dream until...
Hiccups, some freezes, then one day I went into dashboard and my comp froze/dumped out on me.
Rebooted to see a flashing "?" icon on a folder (lucky for me iTunes was backed up).
Went to Apple store two weeks ago - Hard Drive failed they said. Needed a week to order part and fix it and you'll be up and running. During this week they managed to scratch the metal stand, mark up my screen with grease and give me much dirtier version of my iMac. Oh well it's fixed I thought I'll clean it at home and no one looks at the backside. I just missed my Mac!
Got home. Cleaned her up and found Airport missing. iSight light always on. Volume/Sound doesn't work at ALL.
Took it back in and checked in my mac for these problems - Picked it back up yesterday and the three problems I had were fixed, wahoo I thought! When I got home last night I started migrating files over from an external HDD happy about computer being operational and noticing the HDD in the mac sounds a little louder than usual... maybe it's just me? - updated iLife, installed some widgets...
... then while in Utilities folder configuring my Airport Base Station I decided to run Disk Utility for whatever reason.
It's reporting that my S.M.A.R.T. status has failed, I'm not really sure what this means but is sounds bad and it told me to replace the Hard Drive.
After being compless for 2 weeks and lots of back and forth I'm pretty aggravated and disappointed with Apple at this point, is my Hard Drive really going to fail, should I take it back in or is it something I did? The Mac is fairly new! Do I have grounds to demand a replacement? ... ya know how bummy you get when your PC isn't working or gone. sigh
Any insight is appreciated!

Take it back, it's still under warranty. Is this an Apple Store or a 3rd party Apple reseller? Ask to speak to the manager, maybe it is to the point Apple will replace the iMac instead of repairing it.

I downloaded all into a new external hard drive because my internal hard drive was failing. then got internal hard drive replaced by Apple Store. Now when I try to sync IPAD or IPhone to IMAC, photos will not transfer. Why? What shall I do?

Trying to download photos from IPHONE, IPAD to IPHOTO in IMAC after installing new hard drive. Before getting new Hard drive, I downloaded all into external hard drive. photos did not download!

Trying to download photos from IPHONE, IPAD to IPHOTO in IMAC after installing new hard drive.
How did you import the photos to iPad and iPhone?
If the photos have been synced to the iPhone and iPad using iTunes, you cannot sync them back.
See this document: http://support.apple.com/kb/HT4236
You can't reimport pictures synced from your computer to your device back to your computer. You can only import pictures in the Camera Roll or Saved Photos from your device to your computer. If you need to retrieve synced photos from your device:
If your photos are not in the Camera Roll on your devices, save them to the Camera Roll, share them to the Photo Stream, mail the photos, or, if you have iPhoto on the devices, use iTunes Photo Sharing.
http://help.apple.com/iphoto/iphone/2.0/?handbuch#blnkee26bc1
Save photos to your computer using iTunes
Connect your iOS device to your computer.
Tap a photo, album, event, web journal, or slideshow and tap Share> iTunes.
Tap Selected, or change the photos you want to save (if you are saving a slideshow skip to step 4):
Select different photos: Tap Choose Photos, tap one or more photos, and tap Next.
Select a range of photos: Tap Choose Photos, tap Range, tap the first and last photos in the range, and tap Next.
Select all the photos in an album or event: Tap All.
In iTunes, click the button for your device and click Apps at the top of the window.
Below File Sharing, select iPhoto (in Apps).
Select the Shared Photos folder under iPhoto Documents.
Click Save To and select the location on your computer where you want to save the items.
To view your photos, go to the Finder and look in the location you selected above.

Failing internal hard drive

When I run Disk Utility it reports a S.M.A.R.T. status of: Failing for my internal hard drive. I have backed everything up to an external hard drive and am using it as my boot drive. I'm thinking of replacing my internal drive. I was told that I will need to replace it with a 5400 RPM drive. Is this true, or can I replace it with a 7200 RPM drive? Also what is the maximum capacity with which I can replace my internal hard drive? Is there anything else I need to watch for when I get it replaced?
Thanks in advance,
tregarth

7200 would be fine in your computer, but without having an altra ata/133 card inside you are limitied potentially to the 128GB size as was stated. I have heard that there are solftware solutions to this problem if you are interested in putting a larger than 128gb HD in. Another thing is the fact of actually installing the HD, while it is possible to tackle it yourself there are some serious downsides if you do not get the thing back together correctly and with the right amount of torque and thermal paste on the heat sinks...

I have three computers backing up onto the same Time Machine. The Hard drive of one has now failed, and I'd like to restore certain items (principally photographs) to one of the other two computers. How can I do this?

I have three computers backing up onto the same Time Machine. The Hard drive of one has now failed, and I'd like to restore certain items (principally photographs) to one of the other two computers. How can I do this?

"You can also browse the original backup disk for past backups by using "Browse other Time Machine Disks"--to see this choice, hold the Option key then click the Time Machine menu in the Finder (to see the menu, "Show Time Machine status in the menu bar" must be selected in Time Machine preferences."
Mac 101: Time Machine

Internal hard drive/repair: SMART status; Disk Utility, Tech Tool & More

machine: 12" PowerBook 1.5 GHz PowerPC G4 (Aluminium) with 80GB internal HD
internal hard drive (original): Hitachi Travelstar 5K100 series HTS541080G9AT00
hard drive firmware: MB4AA5AJ
ATA version: 6
ATA standard: ATA/ATAPI-6 T13 1410D revision 3a
I have monitored the SMART status etc. of my internal drive with smartmontools for some time. Occasionally, I would see an error or a failed self-test but later testing always succeeded and things did not seem to be problematic.
At the beginning of this week, I started to see a lot of failed self-tests (though some still passed), a rising number of bad ("pending") sectors and reallocation attempts (though no reallocated sectors) and various other errors. The computer seemed to have trouble reading from the disk at times and Carbon Copy Cloner reported two I/O errors when cloning (a later clone succeeded). fsck showed errors although running fsck -fy repeatedly seemed to resolve them.
The Apple hardware tests initially reported an error (2STF/8/3:ATA-100 ata-6-Master) but I hadn't realised I should disconnect peripherals before running it so I did that and repeated the test which found no issues. I ran the extended test a total of three times with no errors.
As I continued to have problems, I booted from my clone and had Disk Utility wipe the drive by writing zeros to it. (I thought trying to get it to write everywhere would either finish the drive off or force it to reallocate the bad blocks. As I understand it, in normal use, the drive won't reallocate the blocks unless it can recover the data in the hopes of reading it at a later time.)
I then continued monitoring the disk using smartmontools. At this point, short self-tests succeed but extended self-tests "disappear". They don't fail, they simply vanish. They begin and smartctl shows the test in progress but then no error or result is logged - it is as if the test was never run. The first time I did this, I got an error saying the SMART attributes could not be read but subsequent tests do not trigger even an error. Short self-tests continue to pass.
There are now (according to SMART) zero bad ("pending") sectors but zero reallocated sectors, which seems odd. The raw read error rate fluctuates (zero one minute, many thousands a while later) although I am not sure it did not do this before.
Disk Utility claims the disk does not support SMART status even though smartctl clearly shows it does. Disk Utility claims the volume is "OK".
I ran Tech Tool Deluxe 3.04 from CD and 3.1.1 from my clone. In both cases, I ran all available tests on the drive. No problems were found.
I am seeing some problems even while booted from my clone - yesterday, the system froze completely and I had to force a shut-down by switching off the power (fsck then found a minor error but repaired it). Just before this happened, I was unable to mount a disk image and was trying to rectify the situation when the system froze. It is possible that the errors fsck corrected were implicated in the freeze, rather than caused by it, since Disk Utility found and repaired similar errors for the other two clones I have (on different partitions of my external drive - yes, I know this is sub-optimal).
Here is some current output from smartmontools:
---output: smartctl -q noserial -a disk0---
smartctl version 5.38 [powerpc-apple-darwin8.11.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K100 series
Device Model: Hitachi HTS541080G9AT00
Firmware Version: MB4AA5AJ
User Capacity: 80,026,361,856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Sat Jul 3 20:28:52 2010 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 55) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 RawRead_ErrorRate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 SpinUpTime 0x0007 142 142 033 Pre-fail Always - 2
4 StartStopCount 0x0012 097 097 000 Old_age Always - 5793
5 ReallocatedSectorCt 0x0033 100 100 005 Pre-fail Always - 0
7 SeekErrorRate 0x000b 100 100 067 Pre-fail Always - 0
8 SeekTimePerformance 0x0005 100 100 040 Pre-fail Offline - 0
9 PowerOnHours 0x0012 039 039 000 Old_age Always - 26720
10 SpinRetryCount 0x0013 100 100 060 Pre-fail Always - 0
12 PowerCycleCount 0x0032 098 098 000 Old_age Always - 4168
191 G-SenseErrorRate 0x000a 100 100 000 Old_age Always - 0
192 Power-OffRetractCount 0x0032 100 100 000 Old_age Always - 201877487644
193 LoadCycleCount 0x0012 001 001 000 Old_age Always - 2209599
194 Temperature_Celsius 0x0002 141 141 000 Old_age Always - 39 (Lifetime Min/Max 16/46)
196 ReallocatedEventCount 0x0032 100 100 000 Old_age Always - 194
197 CurrentPendingSector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMACRC_ErrorCount 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 2138 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
PoweredUpTime is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2138 occurred at disk power-on lifetime: 26716 hours (1113 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
10 51 00 09 4f c2 a0 Error: IDNF
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC PoweredUpTime Command/Feature_Name
b0 d6 01 09 4f c2 a0 00 08:30:04.500 SMART WRITE LOG
b0 d5 01 09 4f c2 a0 00 08:30:04.300 SMART READ LOG
b0 d1 00 00 4f c2 a0 00 08:30:04.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
b0 d0 00 00 4f c2 a0 00 08:30:04.000 SMART READ DATA
b0 da 00 00 4f c2 a0 00 08:30:04.000 SMART RETURN STATUS
Error 2137 occurred at disk power-on lifetime: 26682 hours (1111 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 28 18 95 98 e4 Error: UNC 40 sectors at LBA = 0x04989518 = 77108504
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC PoweredUpTime Command/Feature_Name
25 00 80 c0 94 98 e0 00 1d+01:30:37.600 READ DMA EXT
25 00 80 c0 94 98 e0 00 1d+01:30:30.600 READ DMA EXT
25 00 80 c0 94 98 e0 00 1d+01:30:22.600 READ DMA EXT
25 00 80 c0 94 98 e0 00 1d+01:30:16.300 READ DMA EXT
25 00 80 40 94 98 e0 00 1d+01:30:14.700 READ DMA EXT
Error 2136 occurred at disk power-on lifetime: 26682 hours (1111 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 21 1f 95 98 e4 Error: UNC 33 sectors at LBA = 0x0498951f = 77108511
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC PoweredUpTime Command/Feature_Name
25 00 80 c0 94 98 e0 00 1d+01:30:30.600 READ DMA EXT
25 00 80 c0 94 98 e0 00 1d+01:30:22.600 READ DMA EXT
25 00 80 c0 94 98 e0 00 1d+01:30:16.300 READ DMA EXT
25 00 80 40 94 98 e0 00 1d+01:30:14.700 READ DMA EXT
25 00 80 c0 93 98 e0 00 1d+01:30:14.100 READ DMA EXT
Error 2135 occurred at disk power-on lifetime: 26682 hours (1111 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 22 1e 95 98 e4 Error: UNC 34 sectors at LBA = 0x0498951e = 77108510
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC PoweredUpTime Command/Feature_Name
25 00 80 c0 94 98 e0 00 1d+01:30:22.600 READ DMA EXT
25 00 80 c0 94 98 e0 00 1d+01:30:16.300 READ DMA EXT
25 00 80 40 94 98 e0 00 1d+01:30:14.700 READ DMA EXT
25 00 80 c0 93 98 e0 00 1d+01:30:14.100 READ DMA EXT
25 00 80 40 93 98 e0 00 1d+01:30:13.500 READ DMA EXT
Error 2134 occurred at disk power-on lifetime: 26682 hours (1111 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 28 18 95 98 e4 Error: UNC 40 sectors at LBA = 0x04989518 = 77108504
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC PoweredUpTime Command/Feature_Name
25 00 80 c0 94 98 e0 00 1d+01:30:16.300 READ DMA EXT
25 00 80 40 94 98 e0 00 1d+01:30:14.700 READ DMA EXT
25 00 80 c0 93 98 e0 00 1d+01:30:14.100 READ DMA EXT
25 00 80 40 93 98 e0 00 1d+01:30:13.500 READ DMA EXT
25 00 80 c0 92 98 e0 00 1d+01:30:12.100 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBAof_firsterror
# 1 Short offline Completed without error 00% 26717 -
# 2 Short offline Completed without error 00% 26717 -
# 3 Short offline Completed without error 00% 26717 -
# 4 Short offline Completed without error 00% 26717 -
# 5 Short offline Completed without error 00% 26716 -
# 6 Short offline Completed without error 00% 26715 -
# 7 Short offline Completed without error 00% 26714 -
# 8 Short offline Completed without error 00% 26697 -
# 9 Extended offline Completed: read failure 10% 26692 75071682
#10 Short offline Completed without error 00% 26687 -
#11 Extended offline Completed: read failure 10% 26676 77108511
#12 Short offline Completed: read failure 40% 26663 296917
#13 Short offline Completed without error 00% 26657 -
#14 Short offline Completed: read failure 10% 26646 296918
#15 Short offline Completed: read failure 70% 26645 296905
#16 Short offline Completed: read failure 10% 26644 296910
#17 Short offline Completed: read failure 10% 26644 296910
#18 Short offline Completed: read failure 40% 26643 296916
#19 Short offline Completed: read failure 20% 26643 296909
#20 Extended offline Completed without error 00% 26620 -
#21 Short offline Completed without error 00% 26618 -
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENTTESTSTATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
---end output---
Self-tests 1-8 were all run after I erased the disk. The others were run before I did so. Not listed are the extended self-tests I've started since erasing which, as I say, have simply disappeared.
The checksum error regarding the log is normal for this disk. At least, I've got that error ever since I started using smartmontools for monitoring so I assume it is normal. (I installed this version of the software in about April 2008 and have used it since.) Also, starting offline testing has never succeeded on this disk (I think I checked into this at the time but can't quite remember - this is not new, anyway).
Questions
how should I interpret all this? (Why does Disk Utility say SMART is not supported while smartctl clearly shows it is at the same time? Why do the extended tests simply vanish? Is the drive definitely dying?) I do not want to replace the disk unless I absolutely have to because I understand that replacing disks in 12" PBs is no small matter and cost is an issue. I do not want to replace the machine unless I have to because cost is an issue and, also, I really like this computer and have no idea what I would want in its place, even if expense were no obstacle.
if it isn't clear whether the drive is dying or not, is there some further strategy I can use to establish this?
if the drive is dying, is a machine of this age worth repairing and, if it is, under what circumstances is it worth doing so? For example, it might be worth doing if you can do the job yourself, but that might be quite impractical for non-expert (not to mention, inexpert) users.
if there is a hardware problem (which I obviously think is very, very probable at this point), is it definitely a dying hard drive? (I've seen people write ominous things about disk controllers etc. which I gather are more serious - or less repairable - than a "mere" dying disk.)
what questions should I be asking you and what are the answers to those questions?!
Many thanks for your patience in reading this far.
- cfr

The 12" PB internals are a bit more complex, for PB's. If you don't want to replace the hard drive yourself or pay someone to install it, you could always get an external firewire hard drive, and use it to boot from and for general usage. Would have to be firewire, since the PB won't book from a USB device. One example of what you could get is a 160GB external hard drive: http://eshop.macsales.com/item/Other%20World%20Computing/MS4U5160GB8/ . All the choices with that case are listed here: http://eshop.macsales.com/shop/firewire/on-the-go
Have you called any Apple Authorized Service Providers to see what they would charge to install a drive for you? Whether you bought it or they supplied it? You can find a local one in the US at http://www.apple.com/buy/locator/service/

Failed to upgrade more than one table at same time

Hi
In Deployment Manager, I failed to upgrade more than one table at same time.
I tried to hightlight 4 tables and set the default action as Upgrade, and click File/Generate Deploy. It passed the code generation step then I click Deploy, they are all failed with no error message.
But they are all successful when I upgrade them one by one. Any one has any idea about this?
For the known reason, we have no choice to do the deployment with action of 'upgrade' through OMBPlus, instead, can only do that interactively through OWB Client. I can't imagine to ask our Production side DBA to upgrade 80 tables one by one. Or I have to use the generated scripts to do the upgrade, which will resulted in 'no deploy status updated' in OWB. Any help will be very appricated.
The version I'm using is OWB 10g.
Thanks,
Daming

Hi
First of all, Patrick's solution doesn't work for me. I didn't do cloning and there is no problem when check the WB tables.
Second, I think your solution is only good for the developing environment just to get tables upgrade via deployment manager. In most cases, when you do a new release on PROD environment you just exp/imp the MDL file from DEV to PROD and any developing is not recommended on PROD. But your approach is trying to manually the DB, and then EDIT the mapping to do the Reconcile and then deploy. Surely you can do that if you have full control on your PROD side. However, in my situation, I have no access to the PROD for the security reason and an DBA Operator of the Client is responsible to implement my Migration process on PROD by himself.

Failed boot after moving hard drive (IDE not SATA)

Greetings all.
I am attempting to setup a headless box, and in doing so I am installing Arch on one system (Sapphire Axion A3-M275 Motherboard), then moving the hard drive to the new system (SGS1660, a VIA CLE266/VT8235 based headless rack-solution). After moving the drive into the SGS1660, the system fails to boot. Attached output from the Serial Console:
Booting 'Arch Linux'
root (hd0,0)
Filesystem type is ext2fs, partition type 0x83
kernel /vmlinuz26 root=/dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b r
o console=ttyS0,115200
[Linux-bzImage, setup=0x3600, size=0x1ad6d0]
initrd /kernel26.img
[Linux-initrd @ 0x2ff21000, 0x9e7a5 bytes]
Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.0 20090630 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jul 20 11:20:32 UTC 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002ffd0000 (usable)
BIOS-e820: 000000002ffd0000 - 000000002ffde000 (ACPI data)
BIOS-e820: 000000002ffde000 - 0000000030000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI 2.3 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
last_pfn = 0x2ffd0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e0000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000002ffd0000 (usable)
modified: 000000002ffd0000 - 000000002ffde000 (ACPI data)
modified: 000000002ffde000 - 0000000030000000 (ACPI NVS)
modified: 00000000fec00000 - 00000000fec01000 (reserved)
modified: 00000000ff780000 - 0000000100000000 (reserved)
init_memory_mapping: 0000000000000000-000000002ffd0000
RAMDISK: 2ff21000 - 2ffbf7a5
ACPI: RSDP 000f6ad0 00014 (v00 ACPIAM)
ACPI: RSDT 2ffd0000 0002C (v01 A M I OEMRSDT 09000521 MSFT 00000097)
ACPI: FACP 2ffd0200 00084 (v02 A M I OEMFACP 09000521 MSFT 00000097)
ACPI: DSDT 2ffd0390 03270 (v01 MiniV MiniV080 00000080 INTL 02002026)
ACPI: FACS 2ffde000 00040
ACPI: OEMB 2ffde040 00046 (v01 A M I AMI_OEM 09000521 MSFT 00000097)
0MB HIGHMEM available.
767MB LOWMEM available.
mapped low ram: 0 - 2ffd0000
low ram: 0 - 2ffd0000
node 0 low ram: 00000000 - 2ffd0000
node 0 bootmap 00011000 - 00016ffc
(9 early reservations) ==> bootmem [0000000000 - 002ffd0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 0000626e44] TEXT DATA BSS ==> [0000100000 - 0000626e44]
#4 [002ff21000 - 002ffbf7a5] RAMDISK ==> [002ff21000 - 002ffbf7a5]
#5 [0000099c00 - 0000100000] BIOS reserved ==> [0000099c00 - 0000100000]
#6 [0000627000 - 0000629230] BRK ==> [0000627000 - 0000629230]
#7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#8 [0000011000 - 0000017000] BOOTMAP ==> [0000011000 - 0000017000]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x0002ffd0
HighMem 0x0002ffd0 -> 0x0002ffd0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0002ffd0
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
SMP: Allowing 1 CPUs, 0 hotplug CPUs
No local APIC present or hardware disabled
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 40000000 (gap: 30000000:cec00000)
NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Embedded 11 pages at c1606000, static data 24444 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194911
Kernel command line: root=/dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b ro console=ttyS0,115200
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
NR_IRQS:512
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 1326.894 MHz processor.
Console: colour dummy device 80x25
console [ttyS0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Initializing HighMem for node 0 (00000000:00000000)
Memory: 772708k/786240k available (2905k kernel code, 12976k reserved, 1052k data, 392k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf07d0000 - 0xff7fe000 ( 240 MB)
lowmem : 0xc0000000 - 0xeffd0000 ( 767 MB)
.init : 0xc04e3000 - 0xc0545000 ( 392 kB)
.data : 0xc03d647f - 0xc04dd6a8 (1052 kB)
.text : 0xc0100000 - 0xc03d647f (2905 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 2654.36 BogoMIPS (lpj=4422980)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 10k freed
ACPI: Core revision 20090320
ACPI: setting ELCR to 0200 (from 8c20)
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (2654.36 BogoMIPS).
net_namespace: 1056 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.0: PME# disabled
pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.2: PME# disabled
HPET not enabled in BIOS. You might try hpet=force boot option
pci 0000:00:11.0: quirk: region 0800-087f claimed by vt8235 PM
pci 0000:00:11.0: quirk: region 0400-040f claimed by vt8235 SMB
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:05: ioport range 0xe900-0xe90f has been reserved
system 00:05: ioport range 0xea00-0xea0f has been reserved
system 00:05: ioport range 0xeb00-0xeb2f has been reserved
system 00:05: ioport range 0xec00-0xec7f has been reserved
system 00:05: ioport range 0xe800-0xe83f has been reserved
system 00:07: ioport range 0x3e0-0x3e7 has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x400-0x41f could not be reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0xe0000-0xfffff could not be reserved
system 00:09: iomem range 0x100000-0x2fffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: disabled
pci 0000:00:01.0: MEM window: 0xddd00000-0xdfdfffff
pci 0000:00:01.0: PREFETCH window: 0x000000d5c00000-0x000000ddbfffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 633k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1248948860.509:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1510
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:01.0: disabling DAC on VIA PCI bridge
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 392k freed
:: Loading Initramfs
:: Running Hook [udev]
:: Loading udev...SCSI subsystem initialized
pata_acpi 0000:00:11.1: can't derive routing for PCI INT A
pata_acpi 0000:00:11.1: can't derive routing for PCI INT A
done.
Waiting 10 seconds for device /dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b ...
Root device '/dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b' doesn't exist, attempting to create it
ERROR: Failed to parse block device ids for '/dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b'
ERROR: Unable to detect or create root device '/dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b'
You are being dropped to a recovery shell
Type 'reboot' to reboot
Type 'exit' to try and continue booting
NOTE: klibc contains no 'ls' binary, use 'echo *' instead
If the device '/dev/disk/by-uuid/93df0562-c6e6-4583-9a79-51cd2091247b' gets created while you are here,
try adding 'rootdelay=10' or higher to the kernel command-line
ramfs$
I think what is happening is that the kernel does not have the drivers for the IDE controller on the board for the CLE266/VT8235. Does this seem accurrate? And if so, how can I verify the current kernel config, then compile a kernel with everything else Arch needs to boot properly? I am familiar with the old means of setting up a kernel using the 'make menuconfig; make; make modules_install' etc method.
Thanks for the help in advance!

Hi, not sure if this is still causing you an issue, but I just ran into the same problem.
For me, I have a Sharp PC=MM1110 which has no cd drive and doesn't like to boot from USB. To get Arch installed on it, I had to attach it to another PC (via it's docking cradle, which lets it show up as a USB hard drive), then boot the other PC from an Arch install cd and select the USB hdd for all of the partitioning etc.
When I rebooted after the installation, the Sharp wouldn't boot.
First, I had to edit the grub menu entry to point to (hd0,0), at which point I got the error listed in the first post... Failed to parse block device id's.
If i booted into fallback mode, it booted without a problem.
For me, the solution to finally get it working was to boot into fallback mode, remount the filesystem as r/w, and run mkinitcpio -g filename to rebuild the kernel. Once completed all I had to do was point grub to the new kernel image and it booted ok.
Hope this is useful to someone

Is there an issue with the hitachi hard drives in the MacBook Pro's ? Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue.

Is there an issue with the hitachi hard drives in the MacBook Pro's ? Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue. Other drive I have had have lasted at least 5 or more years.

there is a dylib you can put in the springboard if jailbroken but if not you have to find an apple store

Several user status at the same time

Hi Export,
As I found, we can only choose one status from the list in WBS. Is there any config can make it possible to select multi status in one time?
Thanks,
Liang

Hi
yes you can select more then one user status at the same time
For example you create user status like this in OK02
1     INIT     Initiative
2     DRPR     Draft Proposal
3     PLAN     Fully planned & costed
4     AFEA     502-Approved
5     RELE     Released for execution
6     HOLD     On hold
You can select the user status from the above list
If you set the Initial status flag for the user status
If a status is marked as an initial status, it is automatically activated in an object when the object is created
Thanks
S.Murali

Both Internal hard drives fail on Macbook Pro late-2011

Both internal hard drives (SSD and HDD) failed on Macbook Pro late-2011.
Setup: MBP closed with Thunderbolt display attached.
Problem on HDD-A
I called Apple Support to log an issue with my MBP2011. The system is made up of 2 drives - SSD (128GB) and HDD with 2 partitions HDD-A and HDD-B(original 750GB).
HDD-A has LionOSX 10.7 and HDD-B is storage. SSD has LionOSX on it as well. I normally boot HDD-A.
I was working on HDD-A and the Kernel Panic screen appeared prompting me to shutdown the machine and start it up again.
I tried to reboot HDD-A and the grey progress bar appeared for a long time. I then forced shutdown and rebooted into SSD.
I was able to boot from SSD and then I opened Disk Utility to check the drives. I verified the disk for HDD-A and there was an error. I then tried to repair disk and it couldn't repair it. A dialogue said the disk could not be repaired and that data should be backed up.
HDD-A was not visible in Finder but HDD-B was accessible.
I verified HDD-B and it was "ok".
I shutdown, booted from SSD, disk utility HDD-A and the same message occurred.
I called Apple Support and they advised that I boot from my external HDD which was a clone of HDD-A.
Solution
I was successfully able to boot from the Clone HDD-A.
HDD-A was able to be accessed and I could retrieve the files from HDD-A.
I copied over the latest files from HDD-A to an external drive.
Same Problem on SSD
Boot from SSD, i started working for about 3 hours, with the lid closed, and attached to the ACD.
Kernel Panic screen happened again on the SSD.
Couldn't boot boot from either SSD or HDD-A.
I booted from Cloned HDD-A, Disk Utility verify and repair returned errors on SSD. The same issue had occurred on the second drive.
Disk Recovery from a boot recovery USB thumb, Disk Utility, erased SSD, verify was ok.
Tried to install then there was an install error saying that SSD was damaged (large triangle warning icon). Tried 3 times, failed.
Boot from Recovery Drive HDD-A, downloaded LionOSX.
Next steps
Format HDD-A and HDD-B into 2 partitions
Install LionOSX on HDD A.
Note:
I did not do any software updates for about a week before 14.04.2012 and suspect it might be due to the virus.
I normally work with the lid closed and attached to the ACD, I also suspect that overheating caused both drives to fail. However, I have been using this system with the lid closed for atleast a week. One Kernel Panic screen occured.

Depending on what you are doing on the computer, how hard you are working the computer, it should not overheat. And if it does it should shut down or get very slow because when it starts to overheat the CPU will be throttled back to a lower Ghz speed and or just shut down so it doesn't cause damage to the CPU. The Kernel Panics are a sign that something else is going on. This could be software or hardware.
If after wiping the drives and reinstall Lion on the SSD if the system is running OK then the drives are fine, IE they are not bad. There is something else corrupting them. Again this could be hardware or software, but I doubt it is heat. And using the MBP ion clamshell mode should not cause overheating or excessive heating of either of the drives.
Have you installed iStat Pro or Menu and kept and eye on the temps? If not install iStat Pro and keep and eye on the temps. I bet they do not get above the 150°- 180°F mark which although hot is not overheating.
Be very careful when calling Apple. Removing the DVD drive and installing a hard drive in that bay could void your warranty. The DVD is not a User Removable part and Apple frowns on doing that. So if you call them do not mention that you have replaced the DVD drive with another HDD.
Honestly I suspect you have a hardware problem. But the only way to know that is to install just Lion and your basic programs and run the system. Leave out any AV type software, if you are running some. If you don't get any kernel panics thenn install some of your other software, one programm at a time. If with just the OS and basic software you get a kernel panic then it is hardware related and needs to be checked out by Apple. If you do that re-install the DVD and the original HDD with just the OS on it before you take it in.

I'm an avid Mac enthusiast who works in a creative field. However, I simply cannot afford a new Mac after my old one's internal hard drive failed. Can anyone recommend an affordable Mac option? I don't want to consider a non-Apple product.

I'm an avid Mac enthusiast who works in a creative field. However, I simply cannot afford a new Mac after my old one's internal hard drive failed. Can anyone recommend an affordable Mac option? I don't want to consider a non-Apple product.

Macs with a FireWire port will also boot happily from an External drive. You don't even need to open the MacBook.
Some users buy a drive they would like to have as a future Internal drive, and also buy an external enclosure. They get the External set up the way they want it, then swap with the Internal drive.

My iMac ( Summer 2010 ) internal Hard Drive failing.. It's a Seagate 500GB HDD.

My new iMac ( summer 2010 - July 2010 ) internal Hard Drive is failing..
1) sometimes the imac can't see the hard drive to boot from..
      it would stay in the grey screen ..
2) sometimes the imac boots up after a cold start.
     but some applications such as Safari would die or crash on me.
      I think the file system on the mac is corrupted.
I believe that the internal hard drive is failing..
I can boot up from the external firewire 800 hard drives fine..
The internal hard drive:
Model:   ST3500418AS
Seagate Barracuda 7200.12 SATA 3Gb/s 500GB Hard Drive

Why not starting from the external HDD, and then do a "Repair Disk" of the Seagate.
If that does not help buy a new HDD, put it in and clone the latest external disk to it :
When you have two external disks, make a clone of the Seagate on the one that does not have the latest backup, because the Seagate may fail while doing the cloning. Use Carbon Copy Cloner or Superduper.

TS1967 My computer failed and the main drive had to be formatted but all my music was on a separate internal hard drive. So I downloaded the latest iTunes , problem is it has found all my songs but seems to not recognize half of the album data, half of th

My computer failed and the main drive had to be formatted but all my music was on a separate internal hard drive. So I downloaded the latest iTunes , problem is it has found all my songs but seems to not recognize half of the album data, half of the artists, all of the dates and all ratings data.
I had a large part of it backed up on DVD's but it does not want to recognise them either?
Any tips?

Hey briannagrace96,
Welcome to Apple Support Communities! I'd check out the following article, it looks like it applies to your situation:
iPod: Appears in Windows but not in iTunes
http://support.apple.com/kb/ts1363
You'll want to go through the following troubleshooting steps, and for more detail on each step follow the link to the article above:
Try the iPod troubleshooting assistant:
If you have not already done so, try the steps in the iPod Troubleshooting Assistant (choose your iPod model from the list).
If the issue remains after following your iPod's troubleshooting assistant, follow the steps below to continue troubleshooting your issue.
Restart the iPod Service
Restart the Apple Mobile Device Service
Empty your Temp directory and restart
Verify that the Apple Mobile Device USB Driver is installed
Change your iPod's drive letter
Remove and reinstall iTunes
Disable conflicting System Services and Startup Items
Update, Reconfigure, Disable, or Remove Security Software
Deleting damaged or incorrect registry keys
Take care,
David

Failed to detect hard drive at the first boot

My new system always failed to detect the hard drive at the first boot, but it's ok if restart it. Not use Raid (disabled). Any help will be greatly appreciated. ?(
Yingsheng
KT3-Ultra-ARU
AMD XP1900
GF2MX400
512 PC2100 Mushkin
300W Antec PSU
Western 40G7200PM
Buslink DVD-ROM
Sony CD-RW

Quote
Originally posted by Yingsheng
My new system always failed to detect the hard drive at the first boot, but it's ok if restart it. Not use Raid (disabled). Any help will be greatly appreciated
That is another classic symptom of a WD hard drive being jumpered as either a master or a slave when there is no other drive on the cable with it. If the drive is the only drive on the cable, then remove the jumper from the drive.

S.M.A.R.T status failing on two internal hard drives at the same time.

Similar Messages

Maybe you are looking for