S video, f4 key and headphone jack not working

Hello,
 I bought this (C771) notebook new about 8 months back. I have been using s video port to connect to my TV. However last month it suddenly stopped working. I have checked my s video cable and my TV s video port using my other laptop and they are working fine.
  I am surprised in 8 months itself, s video port has gone bad...OR there is some setting to be done to make it functional again.
Also, I have noticed my f4 ket to switch video outputs is not functional.
Also, the audio output from notebook speakers is very low and the headset jack connection is loose...the pin has to be adjusted to make propoer contact to get the audio out.
Please if somebody can guide me in this matter. Thanks for the help.

Reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

Similar Messages

  • Internal speakers and headphones are not working

    I have hp g6 2231tx os Windows 8, brought it a month ago..now it's internal speakers and headphones are not working..I enabled in playback device from sound mixer and reinstalled drivers but still not working..it's because of hardware or software??

    Hi,
    It could be either Hardware or Software related, so try the following and let me know.
    Download the IDT Audio installer on the link below and save it to your Downloads folder.
    http://ftp.hp.com/pub/softpaq/sp58501-59000/sp58517.exe
    When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers.  Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
    When complete, shut down the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Re-insert the battery and plug in the AC Adapter.
    Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    Let Windows fully load - it will automatically load an audio driver, but just let this complete.  Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation.  When this has completed, right click the speaker icon in the Taskbar and select Playback Devices.  Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Hi, i have a problem that my macBook pro keys suddenly stopped working. The power button,volume keys, brightness keys and shortcuts do not work. Does anyone know why or how i can fix this problem?

    hi, i have a problem that my macBook pro keys suddenly stopped working. The power button,volume keys, brightness keys and shortcuts do not work. Does anyone know why or how i can fix this problem?

    hi, i have a problem that my macBook pro keys suddenly stopped working. The power button,volume keys, brightness keys and shortcuts do not work. Does anyone know why or how i can fix this problem?

  • Satellite Pro A200-18P - microphone / headphone jack not working with Vista

    Hi,
    I have installed Windows Vista onto this laptop which was originally an XP, but I have not got the headphone jack working.
    How do I turn it on or do I have to download it from toshiba website?

    Hi
    First of all you have to check if there is an special BIOS for Vista.
    As far as I know some A200 series needs BIOS which was released especially for Vista OS.
    I think the notebook needs Realtek sound driver.
    Therefore in control panel you should see the Realtek HD audio manager.
    Go there and you will see the mic and headphone jack on the right.
    Click right there and check if there are some settings which have to be enabled.

  • Headphone jack not working iMac 10.5.8

    While playing to the headphones the plug was pulled out of the headphone jack.
    Sound plays through the external speakers but when the headphones are plugged in they are not recognized.
    Tried a different pair of headphones and they did not work.
    Both sets of headphones do work on another computer.
    Reset the PRAM but still no recognition of headphones.
    Plugged headphones in and opened the sound preferences.
    The only choice is internal speakers and there is not a place to change the setting to audio output.
    Restarted the machine with the headphones plugged in but still no recognition.
    Any other ideas before I decide it's just a bad jack?

    Sounds like the headphone port is damaged. Some USB audio solutions exist for the Mac.  You may want to research those over trying to fix the soundboard.

  • Acer Liquid E700 problem with headphone jack, not working properly.

    Here I am again, what a surprise! Reporting another problem with my 2 month old ACER LIQUID E700. Now the problem is, the headphone jack isnt working properly. When I watch movies, or play music with a headphone or earphone, the dialogue or conversations during movies , or the lyrics sang when playing music, can barely be heard. Also , everytime I connect my earphone it the E700, theres a fast ticking sound, which is faint but you can really hear it, and thats when I realized something was wrong. P.S This phone was never dropped or gotten wet. Im really starting to regret buying an acer phone.Any acer representatives out there who know whats going on?

    Well airstrike2014, I do know how it happened to me, it's weird but definitely how it happened, so I was downloading a electrical razor app to scare my friends (I know, it's stupid, but anyway) and the app works by vibrating at full power and playing a electric razor sound, but it would only vibrate (and the app description said that it would make some sounds too) and I tried maxing out my sound but there was really no way to make it play any sounds. I got tired of it 5 mins later and uninstalled thinking the problem was in the app or something, but I go watch a YouTube video right after and no sound was coming out either, even with the volume maxed out and with headphones, so I restart my phone, now sounds play perfectly when there aren't any headphones plugged in but when there are, it now happens what you described there, a tick sound lasting the first few seconds the headphones are plugged in and if I try to play any media it happens that "instrumental effect", other heaphones do the same, so it's obviously the phone.I mean, is it really possible that some kind of problem occurred while trying to vibrate and play sound at the same time? Well it was for me, the phone was fine until then.Sorry for the boringly long post haha

  • The skype video keeps rotating and microphone dones not work

    Hi, I upgraded my laptop (Lenovo P400 touch) to windows 10.  After the upgrade my skype is not working properly.  I have installed the latest version of skype.  My video in the skype keeps rotating and mic in the headphone is not working.  People in the other end are not able to hear my voice propely.What is the solution to this? Karthik

    Try this for the microphone:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00833331&lc=en&cc=us&dlc=en#N74
    For the web cam, go into device manager and see if the web cam is detected and if the driver is loaded.  Check to see if it is disabled or has a yellow ! or red triangle.
    Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

  • 80G Headphone Jack not working

    My 80G iPod headphone jack stopped working.  I did the 5 R's.  Didn't fix it.  Transferred jack out of my old (dead) iPod to my 80G.  Nothing again.  Could have been a bad part though.  Can I buy this part on here?  Or is there anything else I can try?  Thanks a lot.

    Since you seem to know how to take them apart (and have the proper tools), maybe you can buy a broken iPod (of the same type) on eBay for the spare part.  Most iPods with a hard drive that are broken are broken because of a bad hard drive.  So your chances are good that the assembly with the headphone jack will be working.
    And you'll have some other spare parts, such as screen, click wheel, dock connector...
    If that broken iPod is broken because of a bad hard drive, but it is otherwise in better shape than your iPod, you can transplant your working hard drive into that iPod.

  • Y410p Front headphone and microphone jacks not working after repair

    I recently (last month) sent  my IdeaPad Y410p in to Lenovo for repairs due to the laptop not turning on, or repeatedly restarting at the BIOS screen. The laptop was repaired by Lenovo (they replaced the motherboard), and returned it to me. The laptop has worked great sincce then, except that the two USB ports on the right side and the headphone and microphone jacks do not work. I have reinstalled the audio drivers, twice, but have not reinstalled the chipset drivers at all, as I don't want to screw around with those untiol I no more about what I should do. Any help would be appreciated.

    Hi Talonek, welcome to the forums,
    the problem you are experiencing is probably due to the cable connecting the ports on the right side, front of system, to the mainboard unfortunately not being connected or connected properly.  Please see pdf page 52 of the system's Hardware Maintenance Manual.
    I've never taken an Y410p apart, but having looked at the manual the cable connection may well be accessible to check / fix by removing the hard drive.  Another alternative would be to call service and ask them to do this for you.

  • Ipod touch 5 headphone jack not working please help?

    I have tried with multiple pairs of earbuds/ headphones. Either there will be audio in the left, or right, but usually never at the same time unless you twiddle with the headphone plug in. Sometimes there's no audio. I only got the ipod in December, so naturally I'm concerned that there's a problem.
    If anyone has experienced anything like this, your help would be greatly appreicated. Also any help on how to fix it/ what I should do about it would be further appreicated.
    Thanks so much!!

    - Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so.
    Try the following to rule out a software problem
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup
    - Restore to factory settings/new iPod.
    - Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack. If the iPod is defective and not abused Apple will exchange it at no cost
    Apple Retail Store - Genius Bar

  • Headphone jack not working

    Have had external speakers connected to headphone jack for over a year now, worked flawlessly. 
    Upgraded to Lion one month ago.
    Unplugged cord going to external speakers to plug in some headphones.  Headphones worked fine.  Unplugged headphones, plugged in external speakers (back to orignal setup.)
    There is no signal to external speakers now.  I've tested them with an iPod, the cord and speakers work fine when connected to any other device.  The speakers will not work when connected to my iMac.
    I've checked the Audio Out in Settings.  When I connect the speakers, it switches from internal speakers to digital out.
    Any ideas or does anyone know about how much will this cost me to fix?  My warranty expired in Sept. 
    Thanks.

    Try doing a SMC reset and PRAM reset, it's possible you may need to do each reset 2x.
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • 4S Headphone jack not working properly - even after replacement

    Hi all,
    A friend of mine was going to throw their water damaged 64GB iPhone 4S away so I salvaged it.
    The charger port had corroded (main cause for it not turning on - flat) so I replaced it along with the battery, headphone jack, and front glass/display. It basically works fine and feels like a new phone now.
    One issue that persists is the headphone jack is outputting distorted noise when music etc is playing. I'd noticed this before replacing the jack and its replacement has made no difference. (Replaced jack which is attached to mute/vol keys and top mic - all else of which work.)
    The louder you set the volume, the less 'resistance' the distortion seems to have and the music sounds clearer. At the low end of the volume scale there seems to be almost no 'low volume ability' on the phone, ie it's off (move the volume slider just off 0) > it's on and way louder than it should be (clear and fine for about 5 seconds and then distorted/off) > louder with less distortion (also seems to momentarily fix the issue at low volume when increased.)
    I have run the music player all day at mid-high volume to see if it would sort itself out with no improvement or worsening. The earpiece, speaker, microphone, airplay, and all buttons are working as they should, it's just when using headphones do I get this crackling.
    My thoughts are something is stuffed on the main logiboard, but I'm really hoping that may not be the case. Does anyone have any suggestions or ideas?
    Thanks for reading : )
    John

    You need to visit a website such as iFixit with such a question.

  • Redlight from headphone jack not work (Y410p)

    Hello hye  ,Sorry ,  Red light at my headphone jack gone when i format the laptop.
    and i want to ask.  That headphone jack had a driver for red light or not. because it look style when redlight at there..
    Sorry for my ENGLISH
    Solved!
    Go to Solution.

    Welcome to the Lenovo Community !
    I am assuming that you did a One Key Recovery and restored your operating system to a like new condition ? 
    The red light should be OFF when everything is working properly on the your model.  If you did the One Key Recovery then the restoration corrected a driver problem with the audio that was causing the red light.
    Owner & Operator of the following:
    ● Lenovo Ideapad Z570 w/ Win 7 & Win 8.1 Dual Boot ● Lenovo Yoga 3 Pro w/ Windows 8.1 ● Toshiba A75-S206 w/ Win 7
    ● IBM Thinkpad T-23 w/ Win XP ● IBM Thinkpad T-22 w/ Win XP • As well as multiple desktops dual/triple booting XP, Vista and Win 7.
    ★ Find a post helpful? Thank that member by clicking on the ☆Star☆ to the left awarding them a Kudo.
    ★ Posting a problem and a reply is helpful and it answers your question, please mark it as an "Accepted Solution"
    ★ I'm not a Lenovo employee, just a volunteer geek who likes to help folks. Enjoy your time here, pay it forward by helping others !
    ★ Sorry, I don't answer questions via Private Messages. Posting in the appropriate forum is the best way to get assistance.

  • IPhone 4 headphone jack not working right.

    So the headphone jack in my iPhone 4 i don't think is working properly. The right headphone does not put as much sound out as the left. I'm not sure why it was working perfectly just yesterday. I haven't dropped it or got water in it or anything. I tried plugging it in and unplugging it a few times, i reset my phone, turned it off then on and nothing seems to be working. Its not on silent and the volume thing is centered. Idk what could e happening. Help!!!

    I would test the headset in another device such as a computer
    and test another 3.5mm minijack headset in the phone to tell if it's the phone or headset

  • MacBook speakers and headphones are not working! Please help.

    MacBook OS X 10.6.8
    2009 model
    I was watching a movie and my MacBook randomly shutdown by itself. I turned it back on and had no more problems, so I restarted the movie. The audio was not working in my headphones. So I tried the internal speakers and there was still no sound. I did a quick google search which led me to trying various options and finally called Apple Support on the phone.
    I've tried resetting my PRAM but it only showed an alternating screen between grey and black. Nothing happened. I also reset SMC but that didn't work either. I have checked everything in system preferences, Audio MIDI, etc. and it all appears to be correct.
    While on the phone we found that when I plug headphones or an external speaker in, it does not show up on the "output" menu under System Preferences > Sound.
    I do NOT have the money to go to a computer store and the nearest Apple Store is 2 hours away. I desperately need help because most of the work I do involves having to be able to listen to sound. Please help if you can. I'm not ignorant when it comes to computers but I'm no genius. If you have any ideas, please be specific. Your help is very appreciated.
    PS. When a speaker is plugged in at first, I hear a little crackling from it. The same happens to what sounds like internal speakers if I start a video.

    Hi,
    Please use the following instructions to check and fix:
       http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01912228&cc=ad&dlc=en&lc=en&jumpid=reg_r1002_us...
    Good luck.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Maybe you are looking for

  • No tooltips for long filenames in list view any longer?

    hello all, i'm trying to figure out why no tooltips are showing for long file / folder names in finder any longer? they appear in icon view, but i've always used list view and tooltips would normally appear when the cursor is moved over a long filena

  • Remote microphone on MacBook Air

    How do I plug in a remote microphone on MacBook Air?

  • NEED STATIC VARCHAR IN PRO C/C++

    Hello All, I need a static VARCHAR in a C++ Base class to be used by derived classes. I'm having trouble defining the static initializer.. class MyBase { public: EXEC SQL BEGIN DECLARE SECTION; static VARCHAR myBuff [ 10000  ] ; EXEC SQL END DECLARE

  • Ticker Code

    Hello Folks - I am new to Java and like to dive right into some code. I am looking for some sample code for a ticker tape that would scroll along the bottom of the desktop (not within a web browser). The input for the ticker tape would be a text file

  • RWB status 'delivering' and SQL process hangs

    I am sending an IDOC to SQL Server thro XI using JDBC adapter. I am triggering a stored procedure to update SQL tables. The RWB status says 'delivering', sxmb_moni says 'successful' and all the steps are success in audit log. The status 'delivering'