S10-2 LCD screen stays bright white after turning off

I have just replaced a brocken LCD screen of my S10-2 with a compatible LG one (model LP101WS1-TLA1), everything works fine except when I turn off my laptop, the LCD screen won't power off, it stays bright white!
All I can do now is to phsically unplug the battery after each use, and this is driving me nuts!
Has anyone experienced with similar issue? Please help! Thank you!

try to flash bios update first. if it doesn't work, call lenovo support line ship it back,again...
http://consumersupport.lenovo.com/uk/en/DriversDownloads/drivers_show_1590.html

Similar Messages

My screen got totally white after updating to Yosemite

Uploaded the Yosemite to my IMac.
When installing the new update (running OS10.6.8 before) the computer restarted during installation.of program.
After that the screen is just totally white. What happened and what shall I do?

Thank you.
I’m writing from a PC at the moment.
Thanks for the answer. I can’t save anything now, the computer is ‘dead’ it is a shame on all I have on the computer.
And all this problems because of my banc who wanted my to update in order to put in a special identification program.
Who shall I blame?
I have to rebote my computer.
I am crying… ☹
Harriet
Från: Apple Support Communities Updates [email protected]
Skickat: den 17 februari 2015 22:44
Till: Aqua Produkter
Ämne: - My screen got totally white after updating to Yosemite
http://www.apple.com/support/assets/images/external/emails/logo.gif
You received a reply
Kappy<https://discussions.apple.com/people/Kappy?ac_cid=op123456> has replied to your question. You can view the full discussion<https://discussions.apple.com/message/27684871?ac_cid=op123456#27684871> in Apple Support Communities.
My screen got totally white after updating to Yosemite<https://discussions.apple.com/message/27684871?ac_cid=op123456#27684871>
Can you reboot the computer to Snow Leopard? If so, then re-run the Yosemite installer application. It should be in your Applications folder.
If you can't, then you need to erase the drive and reinstall Snow Leopard:
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. After you finish Setup Assistant will complete the installation after which
         you will be running a fresh install of OS X. You can now begin the update process
         by opening Software Update and installing all recommended updates to bring your
         installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1<http://support.apple.com/kb/index?page=answerlink&url=http%3A%2F%2Fsupport.apple .com%2Fkb%2FDL1399&answerid=16777216&src=support_site.downloads.search>.
Correct Answer <https://discussions.apple.com/email/thread/6836494/correct/27684871> Helpful Answer <https://discussions.apple.com/email/thread/6836494/helpful/27684871>
Use the buttons above to tell Kappy and the rest of the community if this reply solved your question or helped you get closer to finding a solution.
To reply to Kappy, go to the discussion<https://discussions.apple.com/message/27684871?ac_cid=op123456#27684871> in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile<https://discussions.apple.com/user-preferences!input.jspa>.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved<http://www.apple.com/legal/> | Privacy Policy<http://www.apple.com/legal/privacy/> | Terms of Use<https://discussions.apple.com/docs/DOC-5952> | Apple Support<http://www.apple.com/support/>

I was trying to make a new screen recording using quicktimeplay, but when I watched the video after recording it all I could hear was me talking while the video was showing on the screen. How do I turn off that recording and turn the right one on? thanks

I was trying to make a new screen recording using quicktimeplay, but when I watched the video after recording it all I could hear was me talking while the video was showing on the screen. How do I turn off that recording and turn the right one on? thanks

Hi j2399123,
It sounds like your screen recording is doing what it was designed to do, capture what is happening on your screen, with optional voice over with the microphone.
Screen recording is for recording what you see on the screen, it is not a "video capture" option, like for capturing a movie with sound that is playing on your screen.
For the QuickTime recording options, check out "Recording with QuickTime Player" in
Mac Basics: QuickTime Player creates, plays, edits, and shares video and audio files
http://support.apple.com/kb/ht4024
And for screen recording specifically, there's
QuickTime Player 10.x: Record your computer’s screen
http://support.apple.com/kb/PH5882
Thank you for thinking of Apple Support Communities for your support needs.
Nubz

New iPad Air 2 with a persisting blank screen. Support site suggests a restore after turning off 'Find my iPhone' on the device. How can I do this with a blank screen?

New iPad Air 2 (December 2014) with a persisting blank screen. Support site suggests a restore after turning off 'Find my iPhone' on the device. How can I do this with a blank screen?

Thanks JimHdk,
After a little more searching across various online resources I was able to cure it by holding down the home button and the on/off button for 10 seconds to restart it and it all came back with a clear screen.

HT201210 My iPod starts to turn on , then it will go white then turn off, then on and repeat.. If I do these steps, will it help ?

Just questioning this.
It says to update software , so I do but once it finishes updating it turns black and turns on with the picture saying I must connect to iTunes.. I tried doing that but for some reason iTunes kept popping up saying that it was in recovery mode and I need to fix it.. so I clicked the button saying restore and 2 times it said it couldn't do it. but the third time it did and once it updated my iPod screen went completely black.. then it turned on as if it was starting up, and it stayed like that for about 5 minutes.. then the screen would flash, turn off, then start up again. It keeps repeating this until my batttery is flat and by that time it tells me to plug it in to a power source. I plug it into the power source hoping it would fix it but it doesn't...once its recharged it starts up the whole, coming on , screen going white, then turning off again and so on. I only just bought my iPod 2 weeks ago so I don't know whats wrong... HELP?
Cheers,
Chelsea

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

After turning off private browsing Safari crashes immediately upon launch.

After turning off private browsing Safari crashes immediately upon launch. I tried soft-resetting, and clearing my cookies and cache. I basically launches in private browsing mode and then immediately tries to switch to regular browsing. When the screen changes, it crashes to desktop.
Any ideas, other than wiping my iPad?
(I'm using iOS 5, of course, but it is not available under the Operating System dropdown in this forum)

I'm seeing the same problem, and it was repeatable for me. iPad (original 3G, 64GB), iOS 5. (There are now a couple threads with this same problem.)
Once the crashes start, it would continue to crash every time I tried to bring up Safari. It crashes just as it finishes showing the tool bars, but before any content is displayed.
Manually killing the app did not make the problem go away.
One time, shutting down and restarting the iPad fixed it, but that solution did not work the next time I went in and out of Private browsing. Also, once the crashing begins, going back into Private browsing did not stop the crashing.
The last time it got into the crashing condition, I stopped the crashing by turning off the setting to display the Bookmark bar. Strange!
I have like 20 Safari crash logs that I hope will get auto-sent to Apple sometime today (I reenabled the send data to Apple option).

I just got my battery and iphone 4 screen fixed and when it turned off because there weren't any battery left, I tried charging it. Now it won't turn on or charge... what do i do?

I just got my battery and iphone 4 screen fixed and when it turned off because there weren't any battery left, I tried charging it. After charging it for like thirty minutes, I pressed the home & lock button and it turned on for a moment for me to see that it was only at 1%... So basically it wasn't charging for that entire half hour. Then, I tried connecting it to my computer and nothing is popping up... so it won't turn on or charge... what do i do?

Who repaired the phone? I suggest taking it back to this repair facility. Since Apple replaces phones instead of repair, the repair facility would be the one to take care of your problem.

HT201401 my iphone has a frozen screen and it does not turn off to reset. what do I do?

My iphone has a frozen screen. It will not turn off to reset. What can I do?

Press and hold the Home and Power buttons for 15-20 seconds until the white Apple logo appears to reset the device.

Efax 7510 still won't work after turning off/on ePrint several times

I'm trying to send an eFax over and over after turning off and on the ePrint button under the webservices menu but without any success. The message keeps stating that it's not connected to a network. I am 100% sure that it is connected to my wireless network because I check that out and print a copy of the page stating that this printer is connected.
What could the problem be? Please help!

Hi daisyforu,
Welcome to the HP Support forums. I understand that you are getting an error message about not being connected when you try to enable the web services for your Photosmart 7510.
The error message you are receiving is indicating that the printer doesn't have an independent connection the internet. Please set a static ip address and manual DNS servers by following the steps below.
1)       Please enter the ip address of the printer into the address bar of your browser (Internet Explorer, Chrome, Firefox, or Safari, etc). My screen shots below are from Safari but the location of everything is the same regardless of the browser. This will bring up the embedded web server of the printer.
2)      Please click on the network tab. You should see the Network Summary for your printer. Please click on 'Networking' on the left hand side menu.
3)      Please click on 'Network Address (IP)' on the left hand side menu.
4)      Please on the radial button beside "Manual IP" then click on "Suggest a Manual IP Address" button. The Manual IP address, Manual Subnet Mask and Manual Default Gateway should populate for you. Please click on radial button beside "Manual DNS Server". For the Manual Preferred DNS Server please enter 8.8.8.8 and for the Manual Alternate DNS Server please enter 8.8.4.4.
5)      Please click on 'Apply'. If you get a warning message about changing the ip address please click 'OK'.
6)      Please turn the printer off by the printer's power button. Please wait a minimum of 15 seconds and then turn the printer back on.
7)      Please press the ePrint icon in the upper left hand corner of the printer's front panel. This should prompt you to accept the terms of service. Please choose 'Accept'.
8)      When prompted about the automatic updates please choose 'Yes'. The printer should now show the HP logo while the printer communicates with the HP servers. The Web Services information sheet should print with the claim code for your printer.
Now that you have the ePrint feature is turned on before using the Fax feature I would recommend that you customize your ePrint email address. I have included a document here on how to do that.
You should now be able to get your eFax setup. I have included a document for you on how to do this here.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

My screen is frozen and wont turn off

The screen is frozen. I can see face time invites appearing on the screen and messages, even the alarm has come on this morning but the screen touch has gone and the sleep button only makes the screen request you 'slide to turn off' but then after plenty of time, the screen it's stuck on comes back - it wont bring the apple icon up.

Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414

No power after turning off and plugging into a new functioning outlet.

No power after turning off and plugging into a new functioning outlet

Perhaps corruption of the Energy Saver settings...
Reset the PRAM cannot hurt.
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Excerpt from http://support.apple.com/kb/ht1379

My 4th gen ipod touch has crashed, just displaying a dark blue screen. It won't turn off or do anything. Connecting it to the laptop does nothing either. Is this common and any ideas??

My 4th Gen ipod touch has crashed, just displaying a bark blue screen. It will not turn off or respond to any buttons being pressed or held for a number of minutes. Connecting to the laptop does not help either. Has anyone had this happen on their i touch or have a solution??
Thanks

If not successful, try the remaining actions of:
iOS: Not responding or does not turn on

My bookmarks are lost after turning off the computer unexpectedly (power problem),how can it recovers?

My bookmarks are lost after turning off the computer unexpectedly (power problem),how can it recovers？ Thanks a lot !!!!
我的书签在电脑突然被断电之后全部丢失了，我该怎么办呢？？谢谢啦！！~~~~

This can also be a problem with the file places.sqlite that stores the bookmarks and the history.
* http://kb.mozillazine.org/Locked_or_damaged_places.sqlite
* http://kb.mozillazine.org/Lost_bookmarks

Notebook showing network activity after turned off

Hi, after turn off my notebook HP Probook 4540s with connected ethernet cable and power source, the RJ-45 connector on my notebook still indicates(LED shines) like there is a network transmission in progress. If I disconnects ethernet cable, indication stops. When I reconnect it back, it starts indicating agian. I thought it was by bios settings something like boot on lan, but it doesn't seem so. Is it common for RJ-45 port to indicates even when is computer turned off? Also I have d-link router, maybe is it a d-link setting?
How to disable network indication when is computer turned off?

I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this HERE.
http://h30499.www3.hp.com/hpeb/
HP ProBook 4540s Notebook PC Support
TwoPointOh
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Restarting music from last played after turn off!!

Has anyone been able to figure out how to resume playback of shuffled music after turning off the ipod touch?? When U turn mine off or the battery runs out I have to start the shuffle from the beginning again. Really annoying isn't it?? Are there any fixes or solutions. Also I have downloaded 1.1.3 and it does the same thing.

Hey sully404847,
Are you turning the iPod off completely? http://docs.info.apple.com/article.html?artnum=305743
Just put the iPod to sleep by tapping the sleep/wake button. Then you can wake it and continue playback. You can also double tap the home button to see iPod playback controls while the iPod is locked.
This article will show you how-to get the most out of your iPods battery.
http://www.apple.com/batteries/ipods.html
Jason

S10-2 LCD screen stays bright white after turning off

Similar Messages

Maybe you are looking for