S10 noise level too high when closed

HI,
I just unpacked a new S10 6423 47G. I was startled by the noise level from the start and now that after completion of the windows setup the noise level has not gone down(I has hoping for a fan control issue), I have stopped further installation and am wondering what to do next.
The three fans seem ok and fairly quiet, I think the installation of the hard drive is also nicely solved.
When the unit is open the noise level is nothing great but ok. As soon as I put the side panel on, I have an increase in noise level that brings me over the tolerance treshold.
I am not sure about the reason, the panel is quite loose but when I press on certain or all parts there is no change in sound. It seems there is resonance in the entire case when I install the side panel. It starts even when the panel is not completey vertfical. In addition to the general noise level there also seems to be resonance of other frequencies as from time to time there is a humming with a frequency of a few changes a minute.
I am really disappointed, the "quiet like whipser noise level" (or so the ad went) was the thing that made me buy this computer without thinking much either about specs or price, I just wanted a reasonably quiet computer.
Any advice?
ThanksM.

Dear Brian,
thanks a lot for your info. I am relieved to see that the noise level is acceptable with your machine. That gives me hope.
FYI, I contacted Lenovo Germany and they were polite but not too helpful, they said that naturally this computer should be louder than a normal pc and did not want to hear much about the way the system is advertised as ultra-quiet. I do not believe in advertising promises but a moderately decent noise level i do expect.
I will return this unit to the dealer and order a new one - hoping that this is only a singular experience.
For me it is not an option to be unhappy with Lenovo - I like the Think series a lot and buy their notebooks all the time for business..
M.

Similar Messages

Mic level too high when recorded, how to fix?

I have an interview where the mic level has been too high when recorded.
The sound is basically usable, it's not all rubbish, but how to fix this?
I know there are tools for this, just don't know what they are.
Thanks for helping.

If the audio is clipped there's not much you can do other than re-record. But there is this: http://www.izotope.com/products/audio/RX/
-DH

Error Rounding Difference too high when reset cleared document using FBRA

My Client has posted cleared document with T_Code F-51. This cleared document has cleared 6040 open items.
And now, they want to reset and reverse that cleared document.
We found error "Rounding difference too high" when we are reset cleared document using FBRA.
Kindly need your advice.
Many thanks in advance.
Regards,

Hello,
Please let me know the ERROR number.
Regards,
Ravi

Audio level too high

I created a slideshow with music behind it in iPhoto. It plays fine althought the audio level is noticably higher than another project I made with a different song. I added both projects to an iDVD project so I can burn 1 disc with both slideshows. They both preview fine in iDVD. Now after I burnt the dvd the audio tracks are distorted when I play them on my home DVD player. It seems the audio level is too high. Is anyone able to tell me how I can adjust my background music level? Thanks for the help.
d

Thanks for the reply John. I thought I saw a setting to change levels somewhere but I think that was when I was importing a movie from my camcorder. I will try to edit the levels as you suggested later today and report back.
Incidentally, the audio is not distorted when I play the dvd from my computer. I am also going to see if I can get some other players to try it on.
Message was edited by: dguiley

Ms word95 to pdf - "security level too high"?

I'm a brand new user of Acrobat 9.0 (on XP system) - all kinds of problems (including major file crash and loss during 9.0 installation - more on that later). for now, I need to get started immediately on converting some MS Word doc files to pdfs - What I get from 9.0 is the message that "The Security Level is Too High". If it's referring to the MS word docs, they are unprotected (I've checked and tried several - Word shows they are not protected, and as far as I know, never have been). They were originally created on a mac with macWord - but were not protected and converted to windows with MacDrive7. They show in MS Word in good condition and unprotected. What do I need to do to get them into acrobat and into pdf format? I've also check the knowledge base here and elswhere without any clues except one chap who seemed to be having similar problems (along with serious crashes) using 8.1. Other than that, I'm mistified.
I've also tried using the context menu 'covert to pdf' method and also creating a new pdf (blank) and inserting them. In both cases the security message aborted the process. Need to do this right away. I'm not technically skilled, so if someone can give me some clear instructions I'd be grateful. - red

Thank you all for responding so quickly. First, I'll mention the serious message and a warning. DO NOT INSTALL ACROBAT 9.0 IN AN ENVIRONMENT WITH WORD 7.0 (or any old(er) MS Word version before 2k). The consequences are ghastly, including the deletion of half or more of your program files (including your email clients, av software and other primary programs), the corruption of your browser, registry (including restore points) and other not so nice events - worse than most bad viruses. That's a problem Adobe and I will probably be taking a look at next week. Mean time, they indicate that they are going to add the matter to their KB and elswhere so that users have a heads-up on the issue.
As for the conversion problem from Word 7.0 .doc to .pdf - Bill, you just about nailed it. It was, indeed, a problem that could be circumvented by going to the printer dialog and setting the printer to 'Adobe pdf file' (something a novice wouldn't think of, nor line tech-support for that matter.). As far as Word/pdf 'printer' is concerned you're just printing the file. However, as I understand things, that's how Adobe attaches the Word documents - It does it through the printer interface. Once that setting is changed to 'Adobe pdf printer' the file is simply picked from the print queue (or before) and loaded into A9. Save it from A9, and the job is done. So, Bill, If Adobe hadn't found the answer, I do believe you would have been telling me exactly how to do it after a few more posts. The credit, though, goes to Neo Johnson, tech-support supervisor in New Delhi. The last two days (almost 9 hours of phone time) were spent with various tech-support agents at Adobe; but, he was the one who finely thought about the interaction between A9 and Word and figured it out.
Ok -that's the brief. The rest is a little history/background for whomever is interested (skip, otherwise - not important). The problem begins with failure to install - first, setup can't find the msi file - it was there, and I browsed it, so that was solved. Then 'invalid licensing - process stopped' messages appear. That was a little tougher and http://kb2.adobe.com/cps/405/kb405970.html and some other articles had me doing repair, reinstall, and other complex (for me) procedures. One of the problems was that flexnet had failed to install, which was a stumper for me (I couldn't find it to download separately - barely knew what it was/did - and finally understood that Adobe was supposed to install it. After that, I did several uninstalls, to no effect. Finally I did a few moderate and then deep uninstalls (with Revo) and several reinstalls. Things got progressively worse. On one reboot, my desktop came up and all the program icons were broken links. I examined targets and such and then went to my 'program files' directory. To my horror, nearly all my primary program (including thunderbird email client, AVG etc.) files had disappeared. The folders were simply empty. Firefox still loaded, but the tabs were non functional. Several checks and some light disc analysis indicated the files vanished. No trace. However, my document folders and data were intact (also backed-up). I went to restore and found that all the old restore points (including the one's Revo sets before uninstalling) were gone. If it had been a virus, it couldn't have done a better job at making a mess of things. At that point, I knew the registry had been toasted and I was facing a complete OS reinstall. Instead, I opted for reinstalling some of the critical programs (and because the document files appeared to be intact). After the first few - thunderbird, firefox etc. - I was relieve to find that they were picking up on the old settings and restoring themselves to their previous states. I still have a number of these to do - and a few must be re-configured. But that's going ok.
Then the saga of Adobe, several phone calls; several times the phone connection was cut off and I had to call again and start over from the beginning with a new person. The matter always had to be esculated to the next tier - more time, more cues, no solutions. They went over the firefox settings, the adobe settings. They were puzzled about the broken links. Attempts to open doc files (after a fresh install of winword) were resulting in 'invalid win32 application'. All kinds of problems made progress difficult. We cleared up the 'invalid....' messages by reparing the file associations (in XP folder options) and then opening the docs in Word and resaving them as something else. It was a labor. Finally, there was simply no answer except, like the post here, Word 7 is simply too old and uses different scripting. The only solution was to either buy (ugh, ouch!) Word 2007 (and hope that it would load them and save them in A9 useable form) or, try installing Word2k (which I have) and processing them through that; and, then using Acrobat 8.x to load those and save the pdfs for A9 to use. However, when Adobe said they could not provide me with a free (even trial) version of 8.x to do the job - licensing problems etc. -- It seemed like a really ugly solution. Finally, I'm begging Adobe to give me a free copy of 8.x and in steps Neo. He can't provide the free copy, but he asks a few questions himself. We go to Adobe and reset some of the security settings (something other agents didn't know or think of). No dice - still can't load the docs. But then he says, Open up Word. Ok. load the file and then hit 'print' - ok, the print dialog comes up. 'Now,' he says, 'open the properties and see what printers are listed.' Ok I do that, and I'll be... 'Adobe pdf printer' is among them. "Just what I thought," he said, Adobe was hooking up with word, but didn't have its printer to attach." So we set 'Adobe pdf' as the printer and lo and behold, the docs loaded into Adobe as pdfs. End of that story. (so bill, you had it too - wish you had answered the phone in the first place!)
Clean up. So, there's a few simple solutions, I think (though i'm no techie and you folks will certainly have better ideas). First, I don't buy the story that early versions of Word are either 1) unsupported by MS or, 2) nobody uses them, as valid reasons why not to fix the problem of the "unloadable" docs. I figure there are at least a couple of aproaches and easy patches that will correct the matter. One is from the Word side - to is to set the current printer setting to use 'Adobe printer', get the file and then reset the printer back to what it was - default. The other is to patch A9 to detect legacy source applications and bypass things that would normally make the file unloadable, unless, of course, they were actually protected or, read only files. In that case, Adobe could simply inform the user to 'unprotect' them, the same as it now does with its 'Security Setting too High' message for later versions. I'm sure there are even better ways. But, that would fix things as far as file loading and conversion.
As to the installation and crash problems - those need to be addressed. Even if its only a few dozen people that might have the same problem, it needs 1) to be given as a noticable warning and keyword in Adobe documents (which now simply indicate that it can process .doc files); 2) it needs to be examined to insure systems that have Word 7.x or older can install without problem, and certainly without harming their system. Adobe has a good reputation and does a good job. That's worth protecting with all customers, even if Marketing can't quite see why and the bean counters can't find much profit in the task. It's what I expect from professionals and to do less certainly subtracts from Adobe's standing. That should be worth a great deal, I would imagine.
Anyway, thanks folks - got to get some sleept, and then get those pdfs done and sent to people who are waiting for them. - best to you all, red.

White Levels Too High?

Hey Everyone:
I am sort of new here, but I have a question. I run a television station and through our broadcast equipment I receive static on some videos I produce that play on a Public Access Channel. In speaking with the cable company we experience problems with they told me that our video levels are too high. The levels are causing static reception on the audio of our video broadcast. It appears that the yellows and whites are causing the most problems. In Final Cut Pro 4.5, I having been playing with the 3-way color corrector and it seems to have calmed down a bit, but I want to eliminate it completely. Does anyone have any suggestions? I want to solve this problem with out sacrificing a lot of the video's quality. I shoot with a Canon GL2 and the video quality is superb. Any suggestions are appreciated.
Thank you,
Chris Steuber

Welcome to the forum Christopher,
I'm not an engineer and don't know proper terminology (though I'm quickly learning , but others on this forum may be able to provide better insight...mine may be a bit vague...
Continue to use CC3way, as it gives you the best control over your image levels.
Are you using a Waveform/Vectorscope, either inside FCP or externally. You should use these tools for proper setting of levels. (preferably externally)
Are you using the FCP 'Range Check' function? This will at least signal you that there are luminance or chrominance hot spots.
Ken Stone has some great info about using CC3way.
One additional thing to consider is the hardware that is in play regarding the distribution of your signal.
I've worked with our local Government Access and Public Access channels (on Adelphia Cable locally) and some of these issues had to be addressed at the head end and some at our end of the signal flow chain...depending on which channel...and we occasionally had to push the Cable ops to tweak their settings, or we had to tweak our hardware at times as well.
In addition to 'hot' video, you should be aware of 'crushed' black levels. As I understand it, digital is not nearly as forgiving as analog when dealing with A/V signals.
Bottom line is, it's your responsibility to make sure your product conforms to 'broadcast standards'.
K

AppleTV distorts sound, output level too high

Hi
I have a problem and have already tried a number of solutions.
My AppleTV sound is distorted, due to the output level being too high. Initially I used the TVs headset jack-connector for connecting to my amp, and lowering the output level from the TV didn't work. It is distorted from the source (AppleTV)
Now I have bought a seperate D/A converter for connecting the AppleTVs optical output directly to my analog amplifier. Still doesn't work. Sound still distorted.
When playing music through AppleTV, I have the ability to adjust the volume level on the source device. And then everything is OK.
But airplaying video/youtube from my ipad (I do that a lot - playing kiddie-flics for my toddler) there is no option to reduce the sound level.
Effectively most content airplayed will be distorted - and I am sick of it. I have a high-end amp and speakers. I do not expect audiophile quality from the AppleTV. Still I didn't expect defective/destroyed sound... And no, the AMP isn't the issue, as this has been replaced as well, due to an upgrade. Same issue on both AMPs.
Any good suggestions? Or should I simply accept that the design criterias for the AppleTV doesn't involve a reasonable audio quality? Or is my particular product defective?
Thanks,
Claus

If the audio is clipped there's not much you can do other than re-record. But there is this: http://www.izotope.com/products/audio/RX/
-DH

HP Pavilion dv7-1130us IDT HD sound card problem: recording levels too high

I have been trying to get the IDT HD sound card in my HP Pavilion dv7-1130us laptop to allow me to switch from "microphone" to "Line In" input signal. I cannot find an option anywhere in the laptop do this. There is not a separate Line-In jack on the laptop. The mike jack is it.
The reason I'm trying to change the input setting is that I am using Audacity/Lame (the Win 7-compatible Beta version) to convert old cassettes to MP3. My laptop came with Vista but I upgraded to Windows 7 Professional (64-bit) earlier this year.
The problem is that recording levels are way too high using the mike input and so the recording comes out harsh and distorted. I have tried all possible recording level adjustments on the tape deck (no option), IDT sound card control panel, Windows device manager, etc.
From what I am reading on the online Audacity forums, using a mike input will cause the recording levels to be too high, and the setting has to be changed to "Line In" and not "microphone." Is there not a way to do that with this laptop and sound card?
The HP Support Assistant tells me that the driver for my sound card is up-to-date.
Thanks in advance for any help or suggestions. I've been trying to find a solution on my own for a couple days with no luck.

Hi Amanda,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp52501-53000/sp52658.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, shut down the notebook, unplug the AC Adapter and then remove the battery. Hold down the Power button for 30 seconds. Re-insert the battery and plug in the AC Adapter.
Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu. Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Let Windows fully load - it will automatically load an audio driver, but just let this complete. Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Error message Translational currency is too high when posting GR for a PO

Hi,
I am trying to post a GR for a PO,with document currency say in GBP and local currency in EUR,when i tried to post a GR the system gives the message with-"Translational currency is too high" and also the value updated for previous GRs(for a qty 10) is vary high like 37,056,361,610.68 GBP,just i want to know how this value is picked by the system,i know exhange rate table maintained is plays important role,but the value i am getting is too high which is not at all related with rates we maintained in the table TCURR.
I want to know why system is giving such a high value.
further PO quantity is 17,000 and net price is 1 GBP.
we have posted very sucessfull GR earlier,but now this high value and error in GR we are facing.
with regards,

Hi,
Good afternoon and greetings,
Wishing you a Happy New Year 2007
Please go through the following OSS Note
Note 191927 - Posting logic: GR for foreign currency PO
Please reward points if found useful
Thanking you
With kindest regards
Ramesh Padmanabhan

Video bit rate too high when try to build and burn. Audio is AC3

I am trying to burn a dual layer DVD and when I go to build/format the DVD it says that the video bit rate is too high. I am confused by this because this DVD was burned previously without a problem. Changes had to be made to the project and the files were compressed in compressor with the same settings and now they do not work. The audio is AC3 dolby. Is there some setting that needs to be changed in DVDSP? What am I missing here...
I am using FC Studio 2.
Thanks!
Natalie

I don't know exactly what the total length of the video is in minutes, but I do know that it is 6.8GB for a dual layer. Probably at least 3 hours. I don't know what the target bit rate is? Is what you are referring is to what the compression I used in compressor?
I am using the setting DVD Best Quality 150 minutes 3.7mbps for video and the AC3 for the audio.
I am recompressing all the videos again just in case there was a problem with one of the compressions. I don't understand why it isn't working this time when none of the settings or compression had changed.
Thanks!!

Noise margin too high

Hi,
I have always had 7Mbps since getting broadband more than 8 years ago. This continued when I switched to bt 3 years ago. I have got a bit lazy checking the speed but have found it has dropped to 2Mbps (checked with BT speed checker and others) when I checked last week. Last year I lost broadband to a fault that was eventually traced to the exchange and fixed. I believe the noise margin was adjusted up then.
I have not changed any phone wiring, router settiings etc in the 3 years I have had bt broadband and the hh3. I don't need it a such a high figure as my broadband has always been stable. I have even moved my hh3 from an extension in the living room to being plugged into the master socket in the hall, to no avail.
Can the mods drop my noise margin to 6db ?
The connection to my hub is 8Mbps from the exchange :
Line state:
Connected
Connection time:
2 days, 05:24:55
Downstream:
7.938 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
13.5 dB / 26.0 dB
Line attenuation (Down/Up):
14.1 dB / 6.5 dB
Output power (Down/Up):
19.9 dBm / 12.1 dBm
FEC Events (Down/Up):
204101 / 102
CRC Events (Down/Up):
192 / 36
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
5811 / 37
Error Seconds (Local/Remote):
17 / 18
Solved!
Go to Solution.

Hi jonbaker65,
Your noise margin is fine. As you are on the 20cn network and close to the exchange the high noise margin just means that if your exchange get's upgraded to the 21cn network then you have lots of margin for improvement.
As your on the 20cn network and on ADSLMax, your IP profile has decreased to 2mbps possibly due to a recently lower sync rate (which has now gone back to ~8mbps)
Normally when this happens the IP Profile should automatically increase in 3 to 5 days time with a stable connection
To confirm this, please can you run a http://speedtest.btwholesale.com speedtest and post the further diagnostic test (You will need to do the quick test first and then click the further diagnostics button)
Then post the speedtest results with the IP Profile, it should look something like this (though ofcourse better then my example below ) :
It is also advised to keep the homehub/router switched on constantly and connected 24/7, as any restarts/disconnections or turning off of the router/homehub will make the dlm (exchange equipment) think there is a problem with your line and will either increase your noise margin, decrease your IP Profile, decrease your sync rate.
This is done automatically to stabilise the line.
Sometimes the IP Profile will not automatically release in the 3 to 5 day period and will require the BT Care Team to manually reset the IP Profile for you.
The BT Care Team usually require a 3+day DSL connection up time to show that your line is stable so that the IP Profile will not just get stuck at 2mbps again in a few days time.
I'm no expert, so please correct me if I'm wrong

Black level too high after calibration

I calibrate my MBP's display (MB470) using Monaco Optix XR. I tried EZ Color and ColorEyes software to create profiles. The result is pretty good in both applications, but both create profiles with lifted black level.
It's much noticable when looking at dark underexposured photos: shadows are 'posterized'.
So. With native MBP profile (Color LCD) shadows are more accurate, but colors are a bit shifted. Calibrated profiles are good at colors, but bad at shadows.
Anybody got good results at calibrating?

Hey Drew,
Gotcha, I just realized it must be fixing something with markers. I haven't had a problem with that yet though, fortunately. I've been exporting directly out of FCP using Compressor, so there's no intermediate file. Like I said, the encoded ac3 sounds perfect, so it seems like it's something happening in DVDSP. Do you know of anything in that program that might have caused this? If it makes any difference, I burned the disc by simply hitting the "burn" button rather than building. Could that cause this sort of thing?
Cameron

Fax Transmission Level too high

Hi,
I have a HP Fax which connecting to my vg224 and a 3745 router to ISDN. The fax report specify that the transimission level -10.2dB was too loud. Is there a way this can be adjustable at the VG 224 voice port? How?
Thanks
Henry

Are you using Fax Relay or Passthrough and if you are using T38 or cisco proprietary protocol.
One thing you might want to check is output attenuation and input gain setting under the voice port configuration mode. try to adjust these settings. It should help.
RGDS
Kashif

Sound level too high new iMac

I see many complaints about low sound, but i have the opposite problem. Whether I use the earphone jacks or my USB headset,the sound level is uncomfortably high.
The only way I can make it at all reasonable is to drag the volume down to where it shuts off and then go into Control Panel to unclick the "Mute" box, leaving the volume bar where it is.
Is there any way to recalibrate this so that the volume slider is useful?

If the audio is clipped there's not much you can do other than re-record. But there is this: http://www.izotope.com/products/audio/RX/
-DH

Audio line-in level too high - an intel issue?

I'd love to hear from anyone who uses their line-in jack to feed in audio; I use mine a lot to digitize old records and tapes.
I've just changed from an eMac G4 to an intel iMac and, using the same audio source (the 'line out' feeds from my home amplifier) connected to the iMac's line-in jack, I'm finding the sound levels are much higher than they used to be. I've checked the Sound Preferences and even with the input volume set at zero, the levels are so high they're almost distorting.
I'm sure this isn't a problem specific to my machine; I've tried my wife's MacBook - also intel - and the same problem occurs.
Having rung Apple Support they say it's not an issue they've come across, so I'd really appreciate hearing from anyone else who has......especially if you're an audio expert!
Best regards and thanks
Chris

Hang on, I'm an idiot...
I've recently put in a new PCI sound card, and I was playing with the input level for that device!
The method in your first post did let me alter the line-in level.
However - here's the problem. I found the level slider was actually right at the bottom. I can now adjust it - but only upwards. So now instead of having a capture that clips the loudest peaks, I can have a capture that clips all the time!
I tried updating the drivers with the ones from NVIDIA's site you linked to, but that did not alter the level of the audio input. (The source is a hi-fi VCR, by the way, and I don't think the output level is particularly high.)
I guess the only way is to put something else in the chain to attenuate the level before feeding it into the line-in?

S10 noise level too high when closed

Similar Messages

Maybe you are looking for