S431 USB 3.0 eXtensible Host Controller Code 10

In Device Manager this controller has a yellow flag and the device status is "This device cannot start. (Code 10)"
I have attempted the following:
1. Uninstalling/Installing drivers from Lenovo Support
http://support.lenovo.com/us/en/products/laptops-and-netbooks/thinkpad-s-series-laptops/thinkpad-s43...
2. Uninstalling ALL USB controllers and having Windows update them upon reboot.
3. Hours of searching online but only seeing the same sorts of "fixes" i.e. uninstalling the controllers and ensuring I am using device specific drivers.
Note: No pins are visibly bent or damaged in the USB port and I don't have anything plugged into them.

Bump
Note:
I need advice regarding a possible "fix"
Some forums suggest removing all power and resetting the CMOS. This would require me to open up the back and disconnect the battery.
Will an action like this void my warranty?

Similar Messages

Intel usb 3,0 extensible host controller driver not working

I have a hp envy sleekbook 6 1100se.
Im facing a problem with the driver of usb 3.0 extensible host controller 0100 microsoft. It says that the device cannot start. gives a CODE 10 error. Im using windows 8. i've tried updating it and uninstalling and reinstalling it but it doesnt help. I've restored the laptop to its factory settings and then for like 10 minutes the usb 3 ports worked fine and so did the driver. but i restarted my pc and again it gave me error code 10. Its also got something to do with the date of the computer. in the events of the driver it said device started in the date 8/28/2012. but after i changed the date it stopped working. but now this fix doesnt work when the second time i reset my computer.
i also know its not a hardware fault because when i plug in my usb in the usb 3 port, the device turns on its light which means that its working. put the computer does not open it or detect the usb drive.
Help please. !

Hi,
Please use the following post:
http://h30434.www3.hp.com/t5/forums/replypage/board-id/General/message-id/76373
Thanks.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

MSI GE60 2OC Windows 7 x64 USB 3.0 eXtensible Host

Hi,
I have another problem with my MSI GE60.
I have installed Windows 7 x64, updated everything and installed driver.
At last I installed the USB 3.0 eXtensible Host Controller driver from the msi homepage. But now my usb ports aren't working anymore!
I tried different driver and deleted them in safe mode from windows.
Help? ...
Thanks in advance

I just posted a similar issue on the same machine, except my USB ports will only work under certain circumstances. It's very odd and it sounds like a driver issue... Did you ever get it sorted out?

Usb pci1033,e0 Enhanced Host Controller G5 PowerPC 1.8GHz

Hi every one
need help to sort this silly problem out
We have a PowerPC G5 1.8 duel fitted with 8GB ram - everything works great until I ftted this USB PCI card
We have just fitted a PCI card into it:
usb pci1033,e0 Enhanced Host Controller (into slot 2)
When I look at mac info it say:
Card                                                       Type
Driver Intalled
pci1033,e0                                              USB Enhanced Host Controller               YES
but under neath type it says:
Card                                                       Type
Driver Intalled
usb                                                          usb                                                            No
usb                                                          usb                                                            No
Now since this PCI card has been fitted - The PowerPC G5 mac will not go to sleep or even shut down.
I have ran the CONSOLE - and cleared the cash prior to asking it to go to sleep and it, when I leave it for 5 munites and move mouse the screen comes back on it says
PROBLEM:
mac will not go to sleep - will not shut down - just says on all night !!!!
The Console gives me this
Anyone know the answer:
would be very much appricated
thanks

Anyone know the answer:
Remove the offending PCI card.
If it is a USB 2.0 PCI controller make sure it has the NEC chipset.
ALI or VIA chipset cards will always cause problems.
NEC chipsets are natively supported in 10.4.3 and onward.
Do NOT install third party USB drivers. Most all cause incompatibilities.
Read more about USB 2.0 PCI cards in PPC Macs:
B8B574BC-BB45-4B3E-9D9B-F97EBB3230BC.html
If it is a USB 3.0 PCI card, forget it. There is no support in PPC Macs.

Virtu Universal and Intel Extensible host controller

Hello guys, two questions
1) In the drivers cd I can't find the Virtu Universal MVP installation program, just the driver.
2) Before upgrading to Win8 , the system forced me to uninstall Intel Extensible USB 3.0 host controller, because it was not compatible.Now at the Intel site there isn't the Win8 compatible download.
My question is, what's the function of this controller ?
Thanks

Quote from: xmad on 03-November-12, 07:29:04
Just download the mvp drivers either from www.lucidlogix.com or msi.
I get this message: "No Intel Ivy Bridge or Sandy graphic device was found, check your bios and verify that integrated graphics is enabled"
Is this related to the fact that ClickBIOS don't work ?
I remember some day ago that I had a sort of Intel control center but I can't find it now in my pc...

VIA OHCI Compliant IEEE 1394 bus host controller Code 10 & 12

Yesterday I finally got my motherboard so I did a clean XP installation (my first board had a falure). The board is a K8N Neo2. The thing is that after the installation I could see an conflict in device manager.
The device that shows a conflict is my IEEE 1394 bus host controller - VIA OHCI Compliant IEEE 1394 bus host controller.
Yesterday it said: This device cannot start (code 10)
today it says: This device cannot find enough free resources that it can use. (Code 12)
Is ther anyone that can help me to get rid of this problem?

try install the lastest edition of via driver

USB 3.0 host controller and USB Root Hub xHCI not showing up on Windows 8.1 laptop

Greetings and thank you for taking the time to read the following message and 'maybe' attempt to help me with my current plight...
I have an HP envy m6 laptop running Windows 8.1 and Windows 7. The problem i am facing at current is that i have only 1 out of 4 usb ports working on my Windows 8.1 partition however on my Server 2012 partition, all four ports are working fine. After asking
around i have come to the conclusion that i'm having a driver issue. I compared what was present on the Windows 7 USB controllers (in Device Manager) to what was present on the Windows 8.1 controllers and i found that my Intel(R) USB 3.0 extensible host controller
- 0100 (Microsoft) and my USB Root Hub (xHCI) was missing on my Windows 8.1 partition.
Now for some background....the problem first occurred when i was trying to solve an external hard drive issue in which none of my external hard drives where showing up when i plugged them into my usb ports, i came across an online solution telling me to
uninstall all my USB drivers in device manager, restart the laptop and let the computer re install the drivers automatically, the result was that i only had 1 out of 4 ports working. Could someone please point me in the right direction in order to fix this
problem?

Windows 8 has native USB 3.0 drivers which explains why you are not seeing an option to roll back. I do not believe you can make the Windows 7 driver work. Have you tried uninstalling in the device manager all usb items and then rebooting to let the drivers reload? Do that with the computer off the dock and then plug it into the dock. As a general rule you should not do driver updates to a laptop through a docking station.

Lenovo Thinkpad E530 - USB 3.0 Ports Not Working Code 10

Hi everyone, so I own a Lenovo E530 with Windows 7 and just earlier today I plugged in my optical mouse into it, about 10 minutes in, Windows gave me a "not enough power message" for my USB 3.0 ports on the left side and they just stopped working. I have 3 USB 3.0 ports on the left side of the laptop, and one USB 2.0 on the right which works just fine.
From there it gave me Code 10 for Teredo Tunneling Pseudo-Interface in the Network Adapter section (which I was able to fix via a registry change) and now what is left to fix is the Intel USB 3.0 eXtensible Host Controller which I cannot seem to fix. I have tried the uninstall/reinstall processes, with Intel's own drivers and Lenovo drivers which were just older version of the Intel USB 3.0 drivers, over and over yet it is still stuck on Code 10, where it will not start.
I never really overused the USB ports either, aside from plugging in a portable USB fan and portable hard drive here and there, and a USB dongle for a wireless mouse and keyboard (Logitech all-in-ones), that is pretty much all I have done with it. I do not believe the ports are not bad or anything, although it may be a hardware problem, but all 3 USB ports still give power on my fan and external HDs when I plug it in, it is just that Windows does not recognize it and nothing happens when I plug something into. But on the other hand, the USB 2.0 port reads just fine and recognizes everything. I have also tried the Troubleshooter multiple times, but everytime it tries to reinstall I get the "Failed" message.
Here is a screenshot of what I am talking about.
http://i.imgur.com/mKqWpFU.png
http://i.imgur.com/RLkbyHY.png
I have tried reinstalling and uninstalling the Intel USB 3.0 eXtensible Host Controller Driver for W7 using the ones listed on the drivers page through Lenovo and using the newest version fround on Intel's webpage as well. Having done these I still could not get it working, so I did a full reformat of the Hard Drive, from there I am able to get the USB 2.0 and 1 of the 3 USB 3.0 ports to work (the very top one above/left of the HDMI port) and recognize devices when I plug them into Windows. But this is working through not having the USB 3.0 Driver installed and just the basic one without having any updates/drivers installed on. Once I install the USB 3.0 Driver back it, it goes back to the original problem.
The problem still persists even though I have done multiple reformats, uninstall/reinstalls, updating to newest drivers and BIOS, etc. I have owned and still own a whole family of Lenovo laptops which still work perfectly fine, but this is the first time I have seen anything like this go wrong in a laptop. Is there anything else I can try to fix this problem? The laptop just went out of warranty a few months ago, and if I were to send it in and get it repaired would it cost me a lot?
Lenovo Thinkpad Edge E530 w/ i5-3210M
Lenovo Thinkpad X230t w/ i5-3320M
Lenovo V570 w/ i5-2410M
Lenovo Thinkpad Edge 14 w/ i5-480M

Hi,
Can you try this
The Device You're missing drivers for (PCI\VEN_1022&DEV_7814&SUBSYS_380217AA&REV_01) is definitely for AMD USB 3.0, this one's off from AMD WEbsite
http://support.amd.com/us/gpudownload/windows/Pages/raid_windows.aspx#2
download the AMD Chipset Drivers see if that'll work.
Have you installed the energy management?
If not please install this as well, I'm thinking this is what the other device is for.
Lenovo Energy Management
emw7034.exe
21.4MB
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Toshiba A60 USB 2.0 Host Controller, Can Anyone Help?

Hi everyone,
I recentry purchased a new Toshiba Satellite A60 notebook. Of course, instantly I formatted it, and installed XP Pro, because I didn't need half the programs that the laptop comes installed with.
Problem is now that all they gave me was a recovery disk (DVD). I have found the ATI and RealTek Drivers with no problems off the Toshiba Download Centre, but I cannot find any USB 2.0 drivers (Host Controller). The USB goes really really slow now. I tried just using a Generic Host Controller, but it goes 10 times slower then if I dont have any controller in there lol.
Im thinking maybe I can get Norton Ghost, and try to view the files that Toshiba used in their Recovery Disk.
I am still stunned why they haven't given me a Drivers CD, first time this has happened to me.
Any Suggestions? Or maybe anyone know where I can get the Host Controller from, that suits the A60?
Thanks in Advance!

HI Ozzie,
Did you not receive the Toshiba Tools & Utilities CD in addition to the Recovery Disks ?
If not then perhaps you could re-install your system from the recovery disks (thereby getting all the correct drivers) and then delete the unwanted software afterwards. This would ensure that you get all the ccompatible drivers for your system
regards,

How to restore, reinstall to WIN 7 vers. USB 3.0 Host Controller after driver upgrade to Win 8

After an undate for the Intell USB 3.0 Host Controller (extensible) as a WIN 8 driver update my DynaDock does not work properly for any devices using the USB ports on the dock and connected to any USB port on the HP Envy 4-1043 laptop. Reading everywhere I can find anything it seems that there is a problem with the Microsoft or Intel driver for the USB 3.0 Host such that the USBs work find when things are plugged directly into them. BUT, when the dynadock is pluuged in and any of its 6 USB ports are used the devices either cannot be found or behavior extremely sluggishly.
This Dynadock has worked well with my last 4 HP computers and worked fine under WIn 7 and 8 on this Envy until the last update of the driver.
I do not know how to re-install the old driver (Hps' WIN7 version sp56724. Can someone please give me the steps or refer me to a source to do this properly?
There is no roll back option in the device manager for this driver. It is grayed out.
I have take pride in not experimenting with 'brihg tiddeas' of how to fix things on this machine. Not that 99% of my gut plus resources from help pages and Miscrosoft did not work before. I do not have a backup computer anymore and I cannot afford the lost of time and productive in making a mess and then spending days trying to undo and fix something that I know others have done well.

Windows 8 has native USB 3.0 drivers which explains why you are not seeing an option to roll back. I do not believe you can make the Windows 7 driver work. Have you tried uninstalling in the device manager all usb items and then rebooting to let the drivers reload? Do that with the computer off the dock and then plug it into the dock. As a general rule you should not do driver updates to a laptop through a docking station.

T430S device manager: USB-IF x HCI USB host controller is not working properly

Hi ,
How to change get ride off the exclamatory mark on this device:
Problem:
Device manger Intel WiUSB: USB IF x HCI USB Host Controller always has the exclamartory mark on it.
Device status: This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
Pls help, thanks.

Hey there wche5,
I found some information over on this thread may be beneficial to your situation. This controller enables USB over wireless as part of the Intel (WiDi) Wireless Display function. To obtain a fix you will need to go to the Intel Site, and run the Intel Driver Update Utility. This should identify any Intel drivers you have that are out of date, including the WiDi driver.
Other threads on the forums point directly to this driver by Intel that typically resolves the problem, found on this thread at the end.
I hope this able to assist you in getting a solution to your issue, Thank You wche5!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

USB Host Controller not recognized by Windows 7.

Just installed Windows 7 in a1130n desktop. The USB Host Controller and the Std USB Host Controller are not recognized by the operating system. The USB ports and the media memory ports on the front panel will not work.

My HP Z400 is suffering from the same problem. Did you discover a solution?

Problem in USB-IF xHCI USB Host Controller

Dear,
I hope that you will be fine. My name is Rana Imran and i am using HP ENVY Ultrabook 6-1106tx with Windows 8.1.
I think i have driver problem in USB-IF xHCI USB Host Controller. I am sending you pictures of problem. Please solve this problem.
Thanks
This question was solved.
View Solution.

Hi,
The first suggestion I'd make is to try downloading and reinstalling the switchable graphics driver on the following link as it lists a fix for WIDI.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-114949-1&cc=us&dlc=en&lc=en...
When the reinstallation has com[pleted, restart the notebook.
If you find this has not corrected the issue, try the download available from Intel on the link below.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23861&lang=eng&ProdId=3227
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

KT4VL USB Host controller Problems

I have a KT4VL (MS-67212) and am having problems with the USB Host controller. I am running Win 98SE. This happens wether or not I have any USB devices installed. I have taken out all installed add on cards and tried and still get the same problem.
If I reboot the computer with the USB Host Controller installed, it won't boot. It goes into safe mode where I can uninstall the USB host controller. I can then reboot fine.
Every time I reboot though the hardware detector pops up saying that I need to install the drivers for the USB host controller. If I install them, then everything works fine, all USB devices are found and and function perfectly. That is, until I reboot and it goes to safe mode.
It has the 1.1 bios in it. I didn't install a floppy drive in this PC so I can't flash it at this time, if that is what I need to do.
Can anyone help?
Thanks,
KTGBP

I have a Satellite C855D-S5320. I had my hard drive crash. I installed windows7 64 bit. All the drivers work except the USB Controller. just the Usb ports on the right side of the unit do not work. one of them is a USB 3. I tried all the driver updates off your web site, I tried windows driver search, I tried driver Genius program too. I also ran a diognostic on the motherboard, it shows all working fine. I upgraded the bios and checked settings there as well. Please help if you can, Tom
Attachments:
IMG_0071.JPG ‏452 KB

Windows reports that the "USB-IF xHCI USB Host Controller" device is not working properly.

I have been receiving the following error and instructions to fix it for a long time now, prior to updating to Windows 8.1:
A device is not working properly
Windows reports that the "USB-IF xHCI USB Host Controller" device is not working properly.
Recommended solution to the problemUse Windows Update to check whether new device drivers are available. Proceed as follows:
Open Device Manager
Search in the device manager for the device whose driver you would like to update and double-click on the device name. You may first have to enable the "Show hidden devices" entry in the "View" menu.
Switch to the Driver tab, click Update driver and follow the instructions
When I follow the instructions and try to update the driver, I am told "The best driver software for your device is already installed."
How do I update the driver to stop receiving the error?
This question was solved.
View Solution.

I have solved the initial problem.
I found the solution on the Forum at http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03926756&tmp_task=solveCategory&cc=us&dlc=en&la...

S431 USB 3.0 eXtensible Host Controller Code 10

Similar Messages

Maybe you are looking for