SA30-414 boot from the USB floppy drive

Hi All!
I'm tryin to get my my satellite A30-414 to boot from the USB floppy drive and enter the dos mode, but all i get is a black screen (without a cursor, of course!!), and then the windows XP logon page directly. Can you tell me whether this model has a boot device menu hotkey?
Also, I may have permanently changed some boot configurations (namely by holding down the F12 at startup and then the F2 key at a later try) with my attempts to get the machine to boot from floppy drive: now even when the floppy drive is not connected i get this awkward black screen and then, after a few seconds, the windows logon page. How can I acceed the setup menu and check?
Thanks in advance for your help!

Thanks to you all for your support!
Now I'll tell how this problem originated. I connected the standard usb fdd with a standard DOS boot disk to which I had added a firmware upgrade for my DVDrom unit. I powered on and held the F12 key down expecting to see the boot device selection menu, instead i got a black screen for a few seconds and then the winXP logon page. At this point i rebooted and held down the F2 key with the same purpose. But the computer went into some kind of hybernation and by pressing the power-on button it shut down.
From that moment on startup I don't see the BIOS POST page anymore: countless seconds of black screen and then the WinXP logon page. The most optimistic explanation to this is that i inadvertently changed the boot order, so it searches for floppy first, and when it doesn't find it then it goes to C:\. Does it sound logical?

Similar Messages

  • Will a T21 boot from a USB floppy drive?

    Hiya,
    I've got a few problems with my T21 and I need to boot it from floppy to sort them, but don't have a floppy drive for it - if I get hold of a USB floppy drive, will it recognise it and boot from it okay or will I be wasting my money?  Unfortunately, I need to sort it today so only have time to get a USB drive - if I had the time I'd just order an ultrabay one and all would be well!
    Cheers,
    Mel.

    Craig,
    You are correct that you cannot boot an OSX USB drive to a PPC (PowerPC) computer but this will not be necessary to install the software on the HD.
    However, let me ask a few more questions:
    -Which model eMac do you have? For example, in your System Profiler, it should report 'Model Identifier: PowerMac4,4' if you have the 800MHz or 1.0GH eMac released in 2003. Depending on your model, only certain versions of OSX will boot your eMac.
    -Are the 10.3 and 10.4 OSX DVDs you have retail, full-install versions, or are they machine-specific, meaning they came bundled with a particular computer?
    -Do you wish to install MacOS 9 on the Lombard?
    OWC does ship International and I believe they are very fast. Please email them for specifics.
    You might consider spending a few more dollars for this combo FireWire/USB2.0 HD enclosure. I have a few and they are excellent; it has the FireWire Oxford 911 chipset plus USB 2.0. Using the FireWire connection, you could install OSX, then reboot your eMac to the Lombard's HD to make sure everything works. If using USB, you can install the software but cannot boot the eMac from the USB HD.
    http://eshop.macsales.com/item/Other%20World%20Computing/MOTGFWU2OB/
    It would be nice if your Lombard had a DVD-ROM drive; then if you ever had to reinstall OSX on the Lombard, you would not have to go through all these hoops. Take a look at this guide and see if you would like to replace your old optical drive. It really is just three or four small screws to remove. The new optical drive will have a generic bezel/faceplate already attached so it won't quite match the old drive.
    http://www.xlr8yourmac.com/PBG3/oem_combo_drives/build_guide/build_combodrive.html
    Message was edited by: jpl

  • I have a MacBook pro late 2011 version it's not booting up so I am trying to boot from a USB recovery drive but when I select it nothing happens it jus goes to the restore options

    I have a MacBook pro late 2011 version it's not booting up so I am trying to boot from a USB recovery drive but when I select it nothing happens it jus goes to the restore options

    Bahamaguy wrote:
    I have a MacBook pro late 2011 version it's not booting up ....
    So what you want is to be able to boot from OS X and retrieve your files
    Create a data recovery/undelete external boot drive
    Of course if it's not booting up, it's easier to fix in place
    ..Step by Step to fix your Mac
    https://discussions.apple.com/community/notebooks/macbook_pro?view=documents#/
    ...so I am trying to boot from a USB recovery drive but when I select it nothing happens it just goes to the restore options
    "Recovery HD" is a partition on your boot drive which you option or commnad r key held at boot time to get into and then repair the Macintish HD partition.
    If you have this on a external USB thumb drive, then that's all it is, no OS X, programs or files.
    If your talking a USB external drive, it has to be a OS X bootable clone made with Carbon Copy Cloner or SuperDuper and the option key held at boot time gives you that boot option.
    Most commonly used backup methods
    So what your saying is you have a external clone and by holding the option key down at boot all you get is it directly going to Recovery HD?
    There is no Startup Manager option to choose what to boot from?
    This could mean Apple changed something, or your external bootable clone isn't one, or the wrong software used so it's not being recognized by Startup Manager as a bootable option.
    What did you use to make the external OS X USB bootable drive?

  • I have a 2012 Mini with a fusion drive that won't boot from a usb cloned drive. It came with 10.8.2 pre installed. I have zapped the PRAM and reset the SMC. Any thoughts?

    I have a 2012 Mini with a fusion drive that won't boot from a usb cloned drive. It came with 10.8.2 pre installed. I have zapped the PRAM and reset the SMC. Any thoughts?

    When I tried using a recently downloaded (from the App store) version of MtLion 10.8.2 (12C60) I could NOT get the new MacMini to install or boot from a USB I had previously made. I was however able to use the Recovery Mode of the MacMini to create a bootable SSD which I had installed. The problem arose when I went back into Recovery DU as it saw the seperate drives (SSD & HD) as a broken Fusion Drive. Interestingly DU from the boot volume had NO issues and reported NO faults. It was the Recovery DU that identified the faulty Fusion Drive configuration. At this point I am definately out of my depth but my speculation is that the Recovery Volume is being used in some fashion to form the method or pattern that DU assigns files to the drives, System Report sees the drives as seperate volumes with all their individual characteristics.
    Disk Utility did not make a bootable USB, I don't have or use CCC or Super Duper.
    Here is the longer version I've been compiling:
    Having bought a late 2012 Mac Mini(6,2) i7 2.66GHZ with the standard 1TB 5400 HD and 4GB of RAM (base model) I immediately decided to install a Mercury Elite 6g 240GB SSD and up the RAM to 16GB. I received both shipments on the same day and had all my new toys in front of me. After following the video advice on OWC’s website for the installation of the second drive I started the mini and formatted the SSD to accept the OS from Recovery on the original HD. This MacMini shipped with 10.8.2 (12C2034) as the OS, the normal build of 10.8.2 is (12C60). Having used Recovery Disk Utility to format the SSD it came back with an error that DU could’t Repair. I went ahead and installed the OS on the SSD and the Mini booted normally from both drives. The issue I encountered with this setup was that iMovie encountered an “unexpected error” and would not save a completed project. I therefore decided to figure the drive issue out because I suspect the new Fusion File Management software didn’t like my configuration with drives that Recovery DU saw as needing to be “fixed”. After spending some time on the phone with both OWC and Apple Support I took the plunge and used Internet Recovery Disk Utility and allowed both drives to be “fixed” after which DU created a Fusion Drive (Logical Drive) that I then ran Repair Disk on and it showed up as a single drive in DU. It works perfectly as described by Apple’s site:
    http://support.apple.com/kb/HT5446
    Having checked the Link Speed and Negotiated Speed they both show as 6g so I’m pleased not to have lost performance due to it being fuzed to a 3g 5400 drive. The biggest drawback is that Apple’s Fusion Management only allows for 1 additional partition and I would have preferred more than that.
    I have sourced some additional information here:
    http://blog.macsales.com/15619-special-note-for-adding-an-ssd-to-a-2012-mac-mini ?
    http://blog.macsales.com/15619-special-note-for-adding-an-ssd-to-a-2012-mac-mini ?
    http://blog.macsales.com/15619-special-note-for-adding-an-ssd-to-a-2012-mac-mini ?
    http://blog.fosketts.net/2011/08/05/undocumented-corestorage-commands/
    If anyone has a factory Fusion Drive could you please post the Link and Negotiated Speeds of both drives? This information can be found in Apple > About This Mac > More Info… > System Report >  Serial ATA and the drives should show up as discrete drives with their info listed separately.

  • How do I boot from a USB flash drive?

    I have two different Toshiba laptops. In the BIOS settings I only see the following options.
    Laptop 1:
    CD/DVD
    FDD
    LAN
    HDD1/SSD1
    Laptop 2:
    HDD1/SSD1
    HDD2/SSD2
    eSATA HDD
    CD/DVD
    FDD
    LAN
    Is it possible to make either computer boot from a USB flash drive?
    Thanks in advance for any help,
    yeto

    FDD (Floppy Disk Drive) equates to USB in my Toshiba laptops. Seems like it's taking some BIOS designers a long time to catch up with the rest of the computer world!
    C.B.
    Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

  • I have a time machine backup file on a USB hard drive.  I bought a time capsule / airport extreme, flat 3TB.  I wish to transfer the backup file from the usb hard drive to the time capsule hard drive.  10.6.8

    I have a time machine backup file on a USB hard drive.  I bought a time capsule / airport extreme, flat 3TB.  I wish to transfer the backup file from the usb hard drive to the time capsule hard drive.  10.6.8

    Unfortunately, Time Machine backups that are stored on a drive that has been connected directly to a Mac are completely different than Time Machine backups that are stored on a Time Capsule.
    Frankly, it is not worth the effort and trouble to try to transfer the old backups to the new Time Capsule.....my opinion....having done this in the past.
    It is possible though, but I would not recommend it due to the complexity and downsides involved with this. To give you an idea of how to do this, check out this support article.
    http://pondini.org/TM/18.html
    Even if you transfer the "old" backups over to the Time Capsule successfully, Time Machine will not simply "add on" to the old backups.
    Time Machine will make a new complete backup of your Mac and then add incremental backups from that point.
    My advice.....start a new backup on the Time Capsule and move forward. Keep the USB hard drive around for a month, maybe 2 or 3 in case you need to go back to an old backup for some reason.  At that time, you will not likely need the old backups at all since you will have a current 2-3 month history of new backups.  At that point, you can erase the USB drive and use it for another purpose.

  • My Macbook air flash had gone for a month and I saw Apple's Macbook air flash storage drive replacement program. I'm not sure whether that program is still available for the broken device or not. Now, I'm booting from the external hard drive. Thank you.

    My Macbook air flash had gone for a month and I saw Apple's Macbook air flash storage drive replacement program. I'm not sure whether that program is still available for the broken device or not. Now, I'm booting from the external hard drive. Warranty has gone in October 2013..
    I want to send back my macbook air back to apple store. The problem is that I bought it from US and now, I'm using it in Myanmar. If the program is free of charge for my device, it's worth trying to send back to US. Since mine is broken, I'm afraid Apple will take charges for reparing.
    So, if anyone having the same problem as me, I would like to get suggestion....
    Thank you!!

    I have no idea about how to handle the international aspect of your question.
    But here is the Apple writeup about the problem and the remedy.  Maybe that will help you.
    http://www.apple.com/support/macbookair-flashdrive/

  • Can't boot from a USB flash drive

    I believe this ability was lost after updating to BIOS 80.52 following HP's "strong recommendation".No warning was given that this update would remove this ability and see that "Due to security changes, after this BIOS update is installed, previous versions cannot be reinstalled."
    I have tried disabling Secure Boot and enabling Legacy Boot, and tried re-applying BIOS defaults.
    Is there a particular combination of BIOS settings that I haven't been able to find?As the warranty on my computer expired in July 2014, the HP Customer Support Contact page won't even accept my request for assistance - despite the "strongly recommended" BIOS update being made available *after* this date. I require the ability to boot from USB flash drives ... how can this now be achieved?
    Is there an HP BIOS for a more recent HP product with the JasmineR motherboard (or an AMI or other BIOS) available and how could I install it?
    Boot a BIOS flashing program from CD or DVD and somehow bypass the HP BIOS's block on updates? Thanks in advance for any advice

    Hi, thanks for the quick reply. I don't have another PC handy but will try to find one. The USB flash drive definitely does NOT appear in the boot menu - even as an HDD or CD/DVD as I have seen mentioned elsewhere as a possibility - and all USB devices are enabled in the BIOS settings and USB HDD and USB Floppy/CD are above rEFInd and all other entries in the boot order. I should also have mentioned that I've tried a (Lexar) USB flash drive prepared approximately a year ago with GParted Live which *has* previously booted the machine, and also different models of flash drives (Toshiba, Transcend) and different methods of preparing them such as burning bootable ISO images with Win32DiskImager, Universal USB Installer and Rufus, and manually creating and formatting a bootable FAT32 partition with diskpart (as per https://technet.microsoft.com/en-us/library/jj200124.aspx) and copying in System Rescue CD/GParted/Clonezilla files, ensuring there is an /EFI/BOOT/BOOTX64.efi file. In diskpart, the "attributes disk" command shows that the USB drives are not marked as bootable and "help attributes disk" says READONLY is currently the only disk flag that may be changed. (Don't know if this means anything as the GParted disk isn't "bootable" but did boot) Did the BIOS update disable enumerating USB devices until later in the Windows 8.1 boot process? 

  • My compaq cq62-214nr will not boot from a usb flash drive

    I have a Compaq CQ62-214 NR Notebook. When I enter the bios boot options screen with F9 there is a blank space where Boot from USB/Flash Drive should be. If I enter the bios setup and move usb flash drive up to the first option above Notebook hardrive and Internal CD/DVD Rom ,save the changes to the BIOS then Reboot. Enter the boot options screen again the blank line moves up to the first choice slot but still is blank. If I press enter over that black option the computer does not boot from the OS I have install on the usb flash drive it just starts its normal windows boot screen. YES I have upgraded the BIOS to the lates version F.37
    Can somone tell me what is wrong.

    Try booting into the one time boot menu.
    Step 1: As soon as you turn on the computer on the hp invent screen keep tapping F9 key.
    Step 2: you will get boot otions such as hard drive, optical drive, USb drive
    Step 3: You can hit enter on the usb flash drive. Should boot from the os on your flash drive
    *Although I am an HP employee, I am speaking for myself and not for HP.
    ****Click the White Kudos star to say thanks****
    ****Please mark Accept As Solution if it solves your problem****

  • Booting from a USB DVD drive

    hello,
    i kept searching for solutions to my problem for hours but i didn't find an answer to my question.
    I want to install windows 7 on my 2007 macbook pro (yes pretty old...) but my optical drive is dead and i don't have bootcamp 5 so i can't create a USB disk and boot from it . so i want to know if it's possible to install win from a usb external drive because i really need it .
    thank you

    aycarambaboy wrote:
    so i want to know if it's possible to install win from a usb external drive because i really need it .
    Connect the external drive to the MBP and start it with the OPTION key down.  Then select the external HDD.
    Ciao.

  • Satellite L20-100 can be booted from external USB hard drive?

    I recently bought Toshiba Satellite L20-100 and I wonder if:
    1. is there any possibility to boot this machine from external usb hard drive?
    2. it is possible to attach another internal hard drive?
    Supposing that the both answers above are 'no', how can I solve the following problem: I need hdd space, I need to boot 3 separate Wxp Operating Systems onto the same machine (Toshiba Satellite L20-100).

    Booting from external USB HD - "No" would be the official, mcrsoft sponsored, answer. However, it is possible. Not easy but it can be done. I've seen it done with my own eyes and there are guides how to do this. Just look for it with search engine. But if you have enough disk space you better do what was suggested here - create 3 partitions and use boot manager.

  • Can a Lombard boot from a USB DVD Drive?

    Hi,
    As the title states really, is there a way I can do it?
    Cheers
    Craig

    Craig,
    You are correct that you cannot boot an OSX USB drive to a PPC (PowerPC) computer but this will not be necessary to install the software on the HD.
    However, let me ask a few more questions:
    -Which model eMac do you have? For example, in your System Profiler, it should report 'Model Identifier: PowerMac4,4' if you have the 800MHz or 1.0GH eMac released in 2003. Depending on your model, only certain versions of OSX will boot your eMac.
    -Are the 10.3 and 10.4 OSX DVDs you have retail, full-install versions, or are they machine-specific, meaning they came bundled with a particular computer?
    -Do you wish to install MacOS 9 on the Lombard?
    OWC does ship International and I believe they are very fast. Please email them for specifics.
    You might consider spending a few more dollars for this combo FireWire/USB2.0 HD enclosure. I have a few and they are excellent; it has the FireWire Oxford 911 chipset plus USB 2.0. Using the FireWire connection, you could install OSX, then reboot your eMac to the Lombard's HD to make sure everything works. If using USB, you can install the software but cannot boot the eMac from the USB HD.
    http://eshop.macsales.com/item/Other%20World%20Computing/MOTGFWU2OB/
    It would be nice if your Lombard had a DVD-ROM drive; then if you ever had to reinstall OSX on the Lombard, you would not have to go through all these hoops. Take a look at this guide and see if you would like to replace your old optical drive. It really is just three or four small screws to remove. The new optical drive will have a generic bezel/faceplate already attached so it won't quite match the old drive.
    http://www.xlr8yourmac.com/PBG3/oem_combo_drives/build_guide/build_combodrive.html
    Message was edited by: jpl

  • Booting from a USB Flash Drive and Optimizing Performance

    I know that you can boot Leopard from a USB flash drive, and I have a 16GB flash drive I'm using as a bootup disk on this 2006 MacBook I have that has a broken hard drive (it was recalled, but the recall ended in 2010).
    The problem is that it's very slow. I have about 8GB of free space on it, so it can't be the VRAM being too small. The USB speed just stinks. There must be ways to optimize the OS to run off of a slow drive by accessing data as infrequently as possible. What can I do to speed this up? Should I disable hard disk sleeping? Should I use some kind of Mac tuneup/optimization tool's feature?
    I plan to get an internal hard drive for it, but I'm stuck with this for a while.

    Not all USB2 Flash drives are equal, in fact I bought 2 16 GB USB drives for cheap, as along side of them were even the same brand 16 GB Flash Drives just a different model, for 5 times as much!
    Me was thinking how bad could they be? Well, they could be 5 times worse than other USB2 flash drives... LOL on me!
    They under extremely rare occasions will Read or Write at 5 MB/s, & very often 1 MB/s...
    My Buffalo Flash drives do near USB2's top speed, see some diffs...
    http://usbspeed.nirsoft.net/
    Optimizing yours will give little benefit.
    You could also do a USB2 RAID0 setup if you have enough ports.

  • Can I configure my HP dv7-4165dx to boot from the second hard drive?

    I have had an HP dv7-4165dx for about 20 months now. About 10 months in, the original hard drive burned up because of the placement directly under the GPU (bottom left corner, left of the touchpad and below the keys), which gets hot enough on the top side to make your hand uncomfortable. The symptoms included blue screens, troubles on startups, and finally a system message on boot that said the drive was damaged. Since it was under warrantee, I carried it to Best Buy to have the drive replaced, which took nearly 2.5 months.
    Now, at about 20 months, I am facing the beginning of the exact same symptoms. I noticed that there was a second hard drive bay, away from the GPU, so I purchased the wire needed to use that bay. Now it tells me that there is no bootable disc installed (the hard disk test, in system diagnostics, knows it is there) . I am sure I can swap the drive back to the original bay and be fine but that puts me out $75 for the kit from HP (yeah, I know I may have to eat that if there is no way), but far more importantly it means that I will have another burned out drive (losing everything, again) within a month or two.
    I have looked but I can't seem to find any way to tell it boot from that drive. Is there a way, or am I just out of look due to a poor design? It's been a great machine, except for this issue.
    This question was solved.
    View Solution.

    Hi,
    Unfortunately there is no option to be able to boot from the HDD in the 2nd bay in any of the dv7 series - sorry for the bad news.
    Best regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • C30: Booting from external USB hard drive

    I carry my OS on an external portable USB drive, and then make use of whatever hardware is available where I visit.
    I recently attempted to boot a Lenovo C30 Thinkstation with this external drive, and was unable to do so.  In looking at the BIOS settings, there is no option to boot from USB (other than floppy(?!?) or memory stick).
    Is it possible to boot from an external USB hard drive, and if not, why?
    jerry

    The boot sequence section of our setup menus has been troublesome to say the least (at least through the development phase).  There are various reasons why it is the way it is now....from spec requirements to customer requirements.  So long story short it really needs to be this way, even though situations like the one you encoutered is inconvenient. 
    The USB issue is actually done for security reasons.  For example, many large customers don't want users to have the ability to just walk up and plug in a USB device and allow the system to detect that and attempt to boot to it right away as it is a risk to their image/security.  For this reason, USB devices don't automatically get added to the boot order, and must be added throught he setup menu if needed.

Maybe you are looking for